DX-1000 Series. Rugged Workstation. 7/6th Generation Intel Xeon and Core Processors, Extreme Performance, Compact and Modular Rugged Workstation

Transcription

1 Rugged Workstation 7/6th Generation Intel Xeon and Core Processors, Extreme Performance, Compact and Modular Rugged Workstation DX-1000 Series DOC No: DX-1000 _R1.04_

2 Contents Preface Revision Copyright Notice.. 04 Acknowledgement Disclaimer Declaration of Conformity.. 04 Product Warranty Statement Technical Support and Assistance Conventions Used in this Manual Safety Precautions Package Contents.. 08 Ordering Information Optional Modules & Accessories Chapter 1 Product Introductions 1.1 Overview Highlights Product Pictures Key Features Hardware Specification System I/O Front Rear Mechanical Dimension Chapter 2 System Pin Definitions and Settings 2.1 Settings Location of Connectors, Jumpers and Switches Top View Bottom View Connector / Jumper / Switch Definition Definition of Switches Definition of Connectors Chapter 3 System Setup 3.1 Disassembling the System for Installation Installing Components on Top Side Installing the CPU Installing SO-DIMM Memory Installing a Mini-PCIe/mSATA Card Installing Antennas Installing CFM & CMI Modules Installing a CFM-IGN Power Ignition Module Installing a CMI-COM Module Installing a CMI-DIO Module Installing a CMI-M12 Module Installing a CFM-PoE Module Assembling the System Installing Thermal Pad Installing Top Cover Installing Bottom Cover Installing Components at Front Side Removing the Front Cover Plate Installing a SATA Hard Drive at Front Side Installing a SIM Card Installing the CMOS Battery Fasten the Cover Install an External Fan Installing the Front Cover Plate Wall Mount Brackets DIN-Rail Mount Brackets VESA Mount Side Mount Brackets

3 Chapter BIOS Setup BIOS Introduction Main Setup System Date System Time Advanced Setup CPU Configuration SATA And RST Configuration PCH-FW Configuration ACPI Settings F81866 Super IO Configuration Hardware Monitor S5 RTC Wake Settings Serial Port Console Redirection Network Stack Configuration CSM Configuration USB Configuration Chipset Setup System Agent (SA) Configuration PCH-IO Configuration Security Setup Administrator Password User Password Boot Setup Setup Prompt Timeout Bootup NumLock State Quiet Boot Fast Boot New Boot Option Policy Hard Drive BBS Priority Save & Exit Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset Save Changes Discard Changes Restore Defaults Save as User Defaults Restore User Defaults Chapter 5 Product Application 5.1 Digital I/O (DIO) Application Digital I/O Programming Guide (DIO) Hardware Specification DIO Connector Definition Chapter 6 Optional Module Pin Definitions and Settings 6.1 CFM-IGN Power Ignition Module Connector Location Definitions of Switches CMI-COM Module Connector Definition and Settings CMI-M12 LAN Module Pin Definitions CMI-M12 PoE Module Pin Definitions

4 Preface Revision Revision Description Date 1.0 New Release 2017/10/ Modified CPU Heat Sink picture and related description 2017/10/ Modified IGN DIP Switch Setting 2017/11/ Remove words Pending 2018/1/ Modified steps of Installing CMI-PoE Module. 2018/3/20 Copyright Notice 2017 by Cincoze Co., Ltd. All rights are reserved. No parts of this manual may be copied, modified, or reproduced in any form or by any means for commercial use without the prior written permission of Cincoze Co., Ltd. All information and specification provided in this manual are for reference only and remain subject to change without prior notice. Acknowledgement Cincoze is a registered trademark of Cincoze Co., Ltd. All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners. Disclaimer This manual is intended to be used as a practical and informative guide only and is subject to change without notice. It does not represent a commitment on the part of Cincoze. This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication. Declaration of Conformity FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE The product(s) described in this manual complies with all application European Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques. 4

5 Product Warranty Statement Warranty Cincoze products are warranted by Cincoze Co., Ltd. to be free from defect in materials and workmanship for 2 years from the date of purchase by the original purchaser. During the warranty period, we shall, at our option, either repair or replace any product that proves to be defective under normal operation. Defects, malfunctions, or failures of the warranted product caused by damage resulting from natural disasters (such as by lightening, flood, earthquake, etc.), environmental and atmospheric disturbances, other external forces such as power line disturbances, plugging the board in under power, or incorrect cabling, and damage caused by misuse, abuse, and unauthorized alteration or repair, and the product in question is either software, or an expendable item (such as a fuse, battery, etc.), are not warranted. RMA Before sending your product in, you will need to fill in Cincoze RMA Request Form and obtain a RMA number from us. Our staff is available at any time to provide you with the most friendly and immediate service. RMA Instruction Customers must fill in Cincoze Return Merchandise Authorization (RMA) Request Form and obtain a RMA number prior to returning a defective product to Cincoze for service. Customers must collect all the information about the problems encountered and note anything abnormal and describe the problems on the Cincoze Service Form for the RMA number apply process. Charges may be incurred for certain repairs. Cincoze will charge for repairs to products whose warranty period has expired. Cincoze will also charge for repairs to products if the damage resulted from acts of God, environmental or atmospheric disturbances, or other external forces through misuse, abuse, or unauthorized alteration or repair. If charges will be incurred for a repair, Cincoze lists all charges, and will wait for customer s approval before performing the repair. Customers agree to insure the product or assume the risk of loss or damage during transit, to prepay shipping charges, and to use the original shipping container or equivalent. Customers can be send back the faulty products with or without accessories (manuals, cable, etc.) and any components from the system. If the components were suspected as part of the problems, please note clearly which components are included. Otherwise, Cincoze is not responsible for the devices/parts. Repaired items will be shipped along with a "Repair Report" detailing the findings and actions taken. Limitation of Liability Cincoze liability arising out of the manufacture, sale, or supplying of the product and its use, whether based on warranty, contract, negligence, product liability, or otherwise, shall not exceed the original selling price of the product. The remedies provided herein are the customer s sole and exclusive remedies. In no event shall Cincoze be liable for direct, indirect, special or consequential damages whether based on contract of any other legal theory. 5

6 NOTE CAUTION WARNING DX-1000 Series Rugged Workstation User s Manual Technical Support and Assistance 1. Visit the Cincoze website at where you can find the latest information about the product. 2. Contact your distributor or our technical support team or sales representative for technical support if you need additional assistance. Please have following information ready before you call: Product name and serial number Description of your peripheral attachments Description of your software (operating system, version, application software, etc.) A complete description of the problem The exact wording of any error messages Conventions Used in this Manual This indication alerts operators to an operation that, if not strictly observed, may result in severe injury. This indication alerts operators to an operation that, if not strictly observed, may result in safety hazards to personnel or damage to equipment. This indication provides additional information to complete a task easily. 6

7 Safety Precautions Before installing and using this device, please note the following precautions: 1. Read these safety instructions carefully. 2. Keep this User s Manual for future reference. 3. Disconnected this equipment from any AC outlet before cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage. 7. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 8. Use a power cord that has been approved for using with the product and that it matches the voltage and current marked on the product s electrical range label. The voltage and current rating of the cord must be greater than the voltage and current rating marked on the product. 9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11.If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. 12. Never pour any liquid into an opening. This may cause fire or electrical shock. 13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. If one of the following situations arises, get the equipment checked by service personnel: The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment does not work well, or you cannot get it work according to the user's manual. The equipment has been dropped and damaged. The equipment has obvious signs of breakage. 14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. 7

8 Package Contents Before installation, please ensure all the items listed in the following table are included in the package. Item Description Q ty 1 Rugged Workstation 1 2 CPU Heatsink Thermal Pad 1 3 Utility DVD Driver 1 4 Screw Pack 1 5 Wall Mounting Kit 1 6 Power Terminal Block Connector 1 7 Remote Power On/Off Terminal Block Connector 1 8 FAN Terminal Block Connector 1 9 DVI-I to VGA Adaptor 1 Note: Notify your sales representative if any of the above items are missing or damaged. Ordering Information Model No. Product Description DX-1000-R10 7/6th Generation Intel Xeon and Core Processors, Extreme Performance, Compact and Modular Rugged Workstation 8

9 Optional Modules & Accessories Model No. CFM-IGN01 Description CFM Module with Power Ignition Sensing Control Function, Select 12V/24V CFM-PoE01 CFM Module with PoE Control Function, Individual Port 25.5W CMI-COM01/UB0903 CMI Module with 2x RS232/422/485, 1x Universal Bracket [97 x 18 mm] CMI-DIO01/UB0918 CMI Module with 16x Optical Isolated DIO (8 in/8 out), 1x Universal Bracket [97 x 18 mm] CMI-LAN01/UB0912 CMI Module with 4x RJ45 Ports, Intel I210-AT GbE LAN, 1x Universal Bracket [97 x 18 mm] CMI-M12LAN01/UB0910 CMI Module with 4x M12 A Coded Connectors, Intel I210-AT GbE LAN, 1x Universal Bracket [97 x 18 mm] MEC-COM-M212A/UB0903 Mini-PCIe Module with 2x COM Ports, thin DB9 connector,1x Universal Bracket [97 x 18 mm] MEC-COM-M334A/2xUB0903 Mini-PCIe Module with 4x COM Ports, thin DB9 connector, 2x Universal Brackets [97 x 18 mm] MEC-FIR-M003/UB0901 Mini-PCIe Module with 1x 1394A Port, 2x 1394B Ports, 1x Universal Bracket [97 x 18 mm] MEC-LAN-M002/UB0911 Mini-PCIe Module with 2x LAN Ports, 1x Universal Bracket [97 x 18 mm] MEC-USB-M002/UB0914 Mini-PCIe Module with 2x USB 3.0 Ports, 1x Universal Bracket [97 x 18 mm] FAN-EX100 External Fan with 4pin Terminal Block Plug, Mounting Bracket GS120A24-CIN1 Adapter AC/DC 24V 5.0A 120W with 3pin Terminal Block Plug 5.0mm Pitch, with Tubes GS220A24-CIN1 Adapter AC/DC 24V 9.2A 220W with 3pin Terminal Block Plug 5.0mm Pitch, with Tubes Side-DX DX Series Side Mount Kit Dinrail mount Dinrail Mount Kit, KMRH-K175 9

10 Chapter 1 Product Introductions

11 1.1 Overview The Cincoze DX-1000 is a rugged workstation series based on LGA 1151 socket and Intel C236 chipset supporting 7 th /6 th generation Intel Xeon and Intel Core Processors, DX Series supports 4K resolution through Intel Gen 9 graphics engine with two DDR4 SO- DIMM sockets up to 32GB memory which delivers outstanding computing performance for high-end applications. Despite remarkably compact footprint and rich I/O including 1x DVI-I, 2x Display ports, 2x GbE LAN ports, 4x RS232/422/485 serial ports and 8x USB 3.0 ports, Cincoze provides its exclusive CMI (Combined Multiple I/O) and CFM (Control Function Module) technologies to make DX-1000 Series a highly scalable system for specific applications such as Industrial automation, transportation, machine vision, in-vehicle and mobile surveillance. DX-1000 Series can be expanded with powered serial port, optical isolated digital I/O, multiple GbE LAN, M12 connector, Power over Ethernet and power ignition sensing function through versatile modules. Featuring wide operating temperature (-40 ~ +70 C), wide range DC power input (9~48 VDC), high tolerance to vibration and shock (5/50 Grms), rugged uni-body construction, fanless, cable-less and jumper-less design, the DX-1000 Series is ideal to be deployed in harsh environments. 1.2 Highlights High Performance Supports Intel Xeon /Core i7/i5/i3 processors, DX Series is specially designed to delivering workstation grade performance for multi-task applications. Compact Size Small footprint (3.2 liter) with rich I/O for greater connectivity, 2x front accessible HDD/SDD trays for ease of data maintenance Modular Design Unique CMI, CFM and MEC technologies for modular expansion to satisfy diversified applications 11

12 1.3 Product Pictures Front Rear 1.4 Key Features Supports 7/6th Generation Intel Xeon / Core LGA1151 Socket Type Processors with Intel C236 Chipset 2x DDR SO-DIMM Sockets, up to 32GB Memory Triple Independent Display (1x DVI-I, 2x DisplayPort) 2x 2.5" Hot Swap SATA III HDD/SSD bays, Supports RAID 0/1 3x CMI Interfaces for RJ45/M12 GbE LAN, COM & DIO Expansions 2x CFM Interfaces for Power Ignition Sensing and PoE Functions 4x Full-size Mini-PCIe Slots for Wireless & I/O Expansions EN50155 / EN Certification for Railway Application E-Mark Certification for In-vehicle Application 12

13 1.5 Hardware Specification System Processor Kaby Lake-S - Intel Core i3-7100t: 3M Cache, 3.4 GHz, TDP 35W - Intel Core i5-7500t: 6M Cache, up to 3.3 GHz, TDP 35W - Intel Core i7-7700t: 8M Cache, up to 3.8 GHz, TDP 35W - Intel Core i3-7300: 4M Cache, 4.0 GHz, TDP 51W - Intel Core i5-7500: 6M Cache, up to 3.8 GHz, TDP 65W - Intel Core i7-7700: 8M Cache, up to 4.2 GHz, TDP 65W - Intel Xeon E v6: 8M Cache, up to 4.2 GHz, TDP 73W Skylake-S - Intel Core i3-6100te: 4M Cache, 2.7 GHz, TDP 35W - Intel Core i5-6500te: 6M Cache, up to 3.3 GHz, TDP 35W - Intel Core i7-6700te: 8M Cache, up to 3.4 GHz, TDP 35W - Intel Xeon E3-1268L v5: 8M Cache, up to 3.4 GHz, TDP 35W - Intel Core i3-6100: 3M Cache, 3.7 GHz, TDP 51W - Intel Core i5-6500: 6M Cache, up to 3.6 GHz, TDP 65W - Intel Core i7-6700: 8M Cache, up to 4.0 GHz, TDP 65W - Intel Xeon E v5: 8M Cache, up to 3.7 GHz, TDP 80W - Intel Xeon E v5: 8M Cache, up to 4.0 GHz, TDP 80W Chipset Intel C236 BIOS AMI 16MB BIOS Memory 2x DDR4 260-pin SO-DIMM Sockets, Support up to 32 GB (2133/2400 MHz, Un-buffered and Non-ECC type) Graphics Integrated Intel HD Graphics supports triple independent display (1x DVI-I, 2x DisplayPort) Audio Realtek ALC888-GR High Definition Audio I/O Interface 1x DVI-I Connector (VGA: 1920 x DVI: 1920 x 2x DisplayPort Connectors (3840 x 2x GbE LAN (Support WoL, Teaming, Jumbo Frame, IEEE 1588v2 and PXE), RJ45 GbE1: Intel I210AT, GbE2: Intel I219LM 4x RS-232/422/485 with Auto Flow Control (Support 5V/12V), DB9 8x USB 3.0 (Type-A) 1x Line-out & 1x Mic-in, Phone Jack 3.5mm 1x ATX Power On/Off Button 1x Reset Button 1x AT/ATX Mode Switch 1x Clear CMOS Switch 1x Remote Power On/Off Connector, 2-pin Terminal Block 1x External FAN Connector, 4-pin Terminal Block Expansion Support CFM (Control Function Module) Technology - CFM IGN Module, CFM PoE Module Support CMI (Combined Multiple I/O) Technology - 4x RJ45 GbE LAN Module, 4x M12 GbE LAN Module (via 2x High Speed CMI Interfaces) - 2x COM Module, 16x Optical Isolated DIO Module (via 1x Low Speed CMI Interface) 4x Full-size Mini-PCIe Sockets 1x SIM Socket Storage 2x 2.5 Hot Swap SATA III HDD/SSD Bays, Support RAID 0/1 4x msata (SATA III shared by Mini-PCIe socket) Supports S/W RAID 0, 1, 5 & 10 Other Function Support Instant Reboot Technology (0.2 sec) SuperCap Integrated for CMOS Battery-free Operation Watchdog Timer: Software Programmable Supports 1~255 sec. System Reset Power Requirement Support AT/ATX Power Type Power Input Voltage 9~48VDC 3-pin Terminal Block Power Adapter AC/DC 24V/5A 120W or 24V/9.2A 220W (Optional) Physical Dimension (WxDxH): x 173 x mm Weight: 3.6 kg Extruded Aluminum with Heavy Duty Metal Support Wall / DIN-RAIL / VESA Mounting /Side Mounting Unibody Chassis Fanless Design Jumper-less Design Cable less Design Protection Reverse Power Input Protection Over Voltage Protection: 58V Over Current Protection: 15A ESD Protection: +/-15kV (air), +/-8kV (contact) Surge Protection: 3.84 kv (impedance 12 ohm 1.2/50us waveform) Operating System Windows 10 / 8.1 / 7 Environment Operating Temperature: Kaby Lake-S - 35W TDP CPU: -20 C to 50 C - 51W~65W TDP CPU: -20 C to 45 C - 73W TDP CPU: -40 C to 40 C Skylake-S - 35W TDP CPU: -40 C to 70 C - 51W~65W TDP CPU: -40 C to 55 C - 80W TDP CPU: -40 C to 40 C (With Extended Temperature Peripherals; Ambient with Air Flow; According to IEC , IEC , IEC ) Storage Temperature: -40 C to 85 C Relative Humidity: 40 95% RH (non-condensing) Shock: Operating, 50 Grms, Half-sine 11 ms Duration (w/ SSD, according to IEC ) Vibration: Operating, 5 Grms, Hz, 3 Axes (w/ SSD, according to IEC ) EMC: CE, FCC Class A Safety: LVD (EN ) Fire Protection: EN Railway: EN50155, EN In-Vehicle: E-Mark MTBF: 457,941 Hours Database: Telcordia SR-332 Issue 3, Method 1, Case 3 13

14 1.6 System I/O Front ATX Power On/Off Button Press to power-on or power-off the system DisplayPort Port Used to connect the system with DisplayPort monitor Power LED Indicates the power status of the system HDD LED Indicates the status of the hard drive IGN LED Indicates the status of the IGN function Temperature LED Indicates the temperature of the system Universal I/O Bracket Used to customized I/O output with optional modules IGN Setting Switch Used to set up IGN function USB 3.0 Port Used to connect USB 3.0/2.0/1.1 device AT/ATX Mode Select Switch Used to select AT or ATX power mode Reset Button Used to reset the system Clear CMOS Switch Used to clear CMOS to reset BIOS Removable 2.5 SATA HDD/SSD Bay Used to inserts a 2.5 HDD/SSD SIM Card Slot Used to inserts a SIM card 14

15 1.6.2 Rear DC IN Terminal Block Used to plug a DC power input with terminal block Antenna Hole Used to install an antenna jack LAN Port Used to connect the system to a local area network DisplayPort Port Used to connect the system with DisplayPort monitor DVI-I Port Used to connect a DVI monitor or connect optional split cable for dual display mode Remote Power On/Off Terminal Block Used to plug a remote power on/off terminal block Mic-in Used to connect a microphone Line-out Used to connect a speaker Universal I/O Bracket Used to customized I/O output with optional modules USB 3.0 Port Used to connect USB 3.0/2.0/1.1 device COM Port COM #1 ~ COM #4 support RS232/422/485 serial device 15

16 1.7 Mechanical Dimension 16

17 Chapter 2 System Pin Definitions and Settings

18 2.1 Settings When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is open. Refer to below for examples of the 2- pin and 3-pin jumpers when they are short (on) and open (off). Two-Pin Jumpers Three-Pin Jumpers Open Short All pins are open Pins 1 and 2 are short Pins 2 and 3 are short 2.2 Location of the Connectors, Jumpers and Switches Top View 18

19 2.2.2 Bottom View 19

20 2.3 Connector / Jumper / Switch Definition List of Connector / Jumper / Switch Connector Location COM1_1, COM1_2 CN1 CN2 CN3 CN4, 5, 6 DC_IN1 PWR_SW1 PWR_SW2 DP1 DVI_I1 FAN1 AUDIO1 DP2 LED_B1 USB3_1, USB3_2 USB3_3, USB3_4 BTB_FH2, BTB_FH4 SATA1, SATA2 FS_1 IGN_PH1 BTB_FH1 SW1 SW2 SW3 Power 1~4 24V_12V_1 AT_ATX1 CLR_CMOS1 Reset1 Definition RS232 / RS422 / RS485 Connector LAN1 and USB3.0 Ports LAN2 and USB3.0 Ports Mini PCI-Express Socket + msata + 3G Module Mini PCI-Express / msata Socket 3-pin DC 9~48V Power Input with Power Ignition Connector Power Button Remote Power on/off DisplayPort Connector DVI-I Connector External PWM Fan Connector Audio Jack / MIC_IN / LINE_OUT DisplayPort Connector System LED Connector USB 3.0 Ports USB 3.0 Ports POE LAN Port Board to Board Connector 22 Pin SATA Connector Input Fuse 15A IGN Board to Board Connector DIO+COM Port Board to Board Connector COM1~4 with Power Select IGN Board Function Setting Super CAP SW +5V / +12V Power Output IGN Board Function Select AT / ATX Power Mode Switch Clear BIOS Switch Reset Button 20

21 2.4 Definition of Switches SW1: COM1 / COM2 / COM3 / COM4 Power Select COM1 / 2 / 3 / 4 Voltage Function Setting : Pin Define Switch Location Function DIP1 DIP2 0V(RI) ON (Default) ON (Default) SW1 COM1 5V ON OFF 12V OFF OFF Location Function DIP3 DIP4 0V(RI) ON (Default) ON (Default) SW1 COM2 5V ON OFF 12V OFF OFF Location Function DIP5 DIP6 0V(RI) ON (Default) ON (Default) SW1 COM3 5V ON OFF 12V OFF OFF Location Function DIP7 DIP8 0V(RI) ON (Default) ON (Default) SW1 COM4 5V ON OFF 12V OFF OFF SW3: Super CAP Switch Switch mode Function ON OFF OFF 1 Super CAP Enable (Default) Disable 2 N/A N/A N/A ON 21

22 AT_ATX1: AT / ATX Power Mode Switch Pin Definition 1-2 (Left) AT Power Mode 2-3 (Right) ATX Power Mode (Default) CLR_CMOS1: Clear BIOS Switch Pin Definition 1-2 (Left) Normal Status (Default) 2-3 (Right) Clear BIOS 22

23 2.5 Definition of Connectors CN3: Mini PCI-Express Socket (Support msata and SIM Card to Link feature) Pin Definition Pin Definition Pin Definition 1 WAKE# 19 NA 37 RESERVED 2 3.3V V 38 USB_D+ 3 NA 21 GND 39 RESERVED 4 GND 22 PERST# 40 GND 5 NA 23 PERN0 / SATARP V 6 1.5V V 42 NA 7 CLKREQ# 25 PERP0 / SATARN0 43 GND 8 RESERVED 26 GND 44 NA 9 GND 27 GND 45 CLINK_CLK 10 SIM_DATA V 46 NA 11 REFCLK- 29 GND 47 CLINK_DATA 12 SIM_CLK 30 SMB_CLK V 13 REFCLK+ 31 PETN0 / SATATN0 49 CLINK_RST 14 SIM_Reset 32 SMB_DATA 50 GND 15 GND 33 PETP0 / SATATP0 51 NA 16 SIM_VPP 34 GND V 17 NA 35 GND 18 GND 36 USB_D- 23

24 CN4 / CN5 / CN6: Mini PCI-Express Socket (Support msata feature) Pin Definition Pin Definition Pin Definition 1 WAKE# 19 NA 37 GND 2 3.3V V 38 USB_D+ 3 NA 21 GND V 4 GND 22 PERST# 40 GND 5 NA 23 PERN0 / SATARP V 6 1.5V VAUX 42 NA 7 CLKREQ# 25 PERP0 / SATARN0 43 GND 8 NA 26 GND 44 NA 9 GND 27 GND 45 NA 10 NA V 46 NA 11 REFCLK- 29 GND 47 NA 12 NA 30 SMB_CLK V 13 REFCLK+ 31 PETN0 / ATATN0 49 NA 14 NA 32 SMB_DATA 50 GND 15 GND 33 PETP0 / SATATP0 51 NA 16 NA 34 GND V 17 NA 35 GND 18 GND 36 USB_D- 24

25 LED_B1: Power LED Status LED B1 Power LED HDD LED IGN LED TEMP LED Reset1: System Reset Button Button Push Definition Reset System CN1 / CN2: LAN1 / 2 LED Status Definition Act LED Status Definition Link LED Status Definition Blinking Yellow Data Activity Steady Green 1Gbps Network Link Off No Activity Steady Orange 100Mbps Network Link Off 10Mbps Network Link DC_IN1: DC Power Input Connector (+9~48V) Connector Type: Terminal Block 1x3 3-pin, 5.0mm pitch Pin Definition 1 +9~48VIN 2 Ignition 3 GND 25

26 POWER1 / 2 / 3 / 4: Power Connector Connector Type: 1x4 4-pin Wafer, 2.0mm pitch Pin FAN1: External PWM Fan Connector Connector Type: Terminal Block 1X4 3-pin, 3.5mm pitch Definition 1 +5V 2 GND 3 GND 4 +12V Pin 1 Gap PWR_SW2: Power On/Off, SW Switch Pin Definition 1 GND 2 +12V 3 SENSE 4 Control Pin Definition 1 GND 2 PWR_SW (Note: Please do not apply power to the pins. This port is used to connect a switch.) COM1 / 2 / 3 / 4: RS232 / RS422 / RS485 Connector Connector Type: 9-pin D-Sub COM1 / COM2 / COM3 / COM4 DB9 Pin RS232 Definition RS422 / 485 Full Duplex Definition RS485 Half Duplex Definition 1 DCD TX- DATA- 2 RXD TX+ DATA+ 3 TXD RX+ 4 DTR RX- 5 GND 6 DSR 7 RTS 8 CTS 9 RI 26

27 Chapter 3 System Setup

28 WARNING DX-1000 Series Rugged Workstation User s Manual 3.1 Disassembling the System for Installation In order to prevent electric shock or system damage, before removing the chassis cover, must turn off power and disconnect the unit from power source. 1. Turn over the unit to have the bottom side face up, loosen the 6 screws of bottom cover and place them aside for later use. 2. Remove the bottom cover from the chassis. 28

29 3. Loosen the 4 screws. Pull out 4 latches as marked on photo. 4. Hold front and rear panel and lift up the body of unit vertically. 29

30 5. Turn over the body of the unit and place it gently. 30

31 3.2 Installing Components on Top Side Installing the CPU 1. Locate the CPU socket, remove the protection cover on it. 2. Press the CPU socket lever and pull it aside away from the socket to unlock it. Pull back the lever to open the socket. 31

32 3. Align the notches on CPU with the alignment post on socket. 4. The notches of socket provide the space for fingers while lowering the CPU, hold the CPU by the edges toward the notches and insert the CPU gently. 32

33 5. Place the thermal pad on the CPU heat spreader. Press down the socket lever to lock the CPU. Thermal pad 6. Align mounting holes of heat sink with the four nut studs. 33

34 7. Flip the corner of thermal pad and fasten the heat sink with provided 4 screws.(showing as the picture below) 34

35 3.2.2 Installing SO-DIMM Memory 1. Locate the SODIMM socket on the top side of system. 2. Insert a SO-DIMM module at a 45 degree angle until its edge connector is connected to SO-DIMM socket firmly Lower socket Upper socket 3. Press down the module until the retaining clips snap back in place. Lower socket Upper socket 35

36 3.2.3 Installing a Mini-PCIe/mSATA Card 1. Locate the Mini-PCIe slot on the top side of system. 2. Insert the Mini-PCIe card at a 45 degree angle until its edge connector is connected firmly into slot. For 3G/4G Mini-PCIe card, please install on CN3 slot CN3,4,5,6 slot CN3 slot 3. Press down the card and fasten two screws to fix it. 36

37 CAUTION DX-1000 Series Rugged Workstation User s Manual Installing Antennas Please installing a Mini PCIe Wireless Lan Card on top side before you put on washer and fasten the nut with antenna jack. 1. Remove the antenna rubber covers on rear panel. 2. Penetrate the antenna jack through the hole at both sides as illustrated. 37

38 3. Put on washer and fasten the nut with antenna jack. 4. Assemble the antenna and antenna jack together 5. Attach the RF connector at another end of cable onto the module. 38

39 3.3 Installing CFM & CMI Modules Installing a CFM-IGN Power Ignition Module 1. Locate the IGN connector on the bottom side of system. 2. Fasten 1 copper pillar before insert IGN module. 39

40 3. Insert IGN module vertically to the female connector on the system s mainboard, and fasten 2 screws to fix it. 40

41 3.3.2 Installing a CMI-COM Module 1. Locate the connector of CMI-module on the bottom side of system. 2. Loosen the 2 screws on rear bezel to remove the cover plate 41

42 3. Insert the CMI-COM module carefully into the CMI connector on main board. Fix it with 2 screws. 4. Loosen the 4 D-Sub jack screws as marked on photo. 5. Attach the COM bracket. Fasten 2 screws and 4 D-Sub jack screws to fix it. 42

43 3.3.3 Installing a CMI-DIO Module 1. Locate the connector of CMI-DIO module on the bottom side of system. 2..Loosen the 2 screws on rear bezel to remove the cover plate 43

44 3. Insert the CMI-DIO module carefully into the CMI connector on main board. Fix it with 2 screws. 4. Attach the DIO bracket, and fasten 2 screws to fix it. 44

45 3.3.4 Installing CMI-M12LAN Module Note: The photo example in this section is illustrated by CMI-M12LAN01/UB0910 module as shown in below picture. 1. Loosen the 2 screws on front bezel to remove the cover plate. 45

46 2. Remove 4 rubber rings on M12 jacks; Penetrate M12 jacks of CMI module through the accompanying M12 I/O bracket. then fasten 4 ring hexes onto jacks as illustrated in right hand picture below. Rubber rings 3. Locate the CMI connector on the top side of system. 46

47 4. Exchange screw to copper pillar before insert the CMI module. 5. Insert the CMI module vertically into the female connector on system s mainboard until it s connected firmly and fasten 4 screws to fix it. 47

48 6. Fasten 2 screws on cover plate. 48

49 3.3.5 Installing a CFM-PoE Module 1. If you use CMI-RJ45LAN Module (CMI-LAN01), please paste the shading tape to the place which was marked by red circle. If you use CMI-M12LAN Module please skip this step. (Note: Please don t block the LED.) 2. Insert the CMI-M12 module vertically into the female connector on system s mainboard until it s connected firmly, and fasten 4 copper pillars to fix it. 49

50 3. Turn over the heatsink and locate the two places which were marked by red circles. 4. Please paste the 2 thermal pads onto the heatsink carefully. 50

51 5. Please paste the heatsink onto the CMI-PoE module carefully and connect the PoE module to the CMI-M12 module. 6. Fasten 4 screws to fix it. 51

52 7. Please paste the thermal pad onto the heatsink carefully. 52

53 3.4 Assembling the System Installing Thermal Pad Note: The DX-1000 series don t need to additional installation of the PCH thermal pad. Thermal pad Installing Top Cover 1. Hold front and rear panel and put the body of unit back to chassis and fasten the 4 screws as marked on photo.. 53

54 3.4.3 Installing Bottom Cover 1. Place the bottom cover back to system. 2. Fasten the bottom cover with 6 screws. 54

55 3.5 Installing Components at Front Side Removing the Front Cover Plate 1. Loosen 2 screws on front panel to remove cover plate. Note: It s advised to fasten the 2 screws manually. If fastened with an electrical screw driver, please set the torque of the driver to 2.5KgF Installing a SATA Hard Drive at Front Side 1. Locate the removable HDD bay and loosen the screw. 55

56 2. Pull the rotating arm and pull the HDD bracket out of system Make the bottom side of the HDD face up, place the HDD bracket on it. Ensure the direction of bracket is correct and use 4 provided screws to assemble HDD and HDD bracket together. 56

57 4. Align the HDD bracket assembly with the entrance of removable HDD bay. Holding the rotating arm and insert the HDD bracket until the connector of HDD contact the SATA connector firmly. 5. Place the rotating arm back and fasten the screw. 57

58 3.5.3 Installing a SIM Card 1. Locate the SIM card slot at front side. 2. Insert a SIM card into SIM slot with the gold contacts facing up. Please pay attention to the insert orientation as illustrated. 58

59 3.5.4 Installing the CMOS Battery 1. Locate the removable CMOS Battery and loosen the screw. 2. Pull out the CMOS battery bracket with assistance of a tweezer. 59

60 3. Insert a CMOS battery in the battery slot. 4. Insert the battery bracket firmly and fasten the screw. 60

61 3.5.5 Fasten the Cover 1. Fasten the cover by using the two screws Install an External Fan 1. Prepare an external fan. Loosen the 2 screws halfway on mounting frame before attempting to install it. 61

62 2. Slide the FAN into the middle groove of chassis as illustrated. Tighten the 2 screws to fix it onto chassis. 3. Move the fan to the center of chassis. Tighten the 2 screws marked on photo to secure it. 62

63 4. Connect the FAN cable to external fan power connector at rear panel. 63

64 3.6 Wall Mount Brackets DX-1000 series offers wall mount brackets that customers can install system on the wall in convenient and economical ways. 1. The mounting holes are at the bottom side of system. Use provided 8 screws to fasten the bracket on each side. 2. There are 2 bracket mounting holes at left and right side for customer fix the system on the wall. 64

65 3.7 DIN-Rail Mount Brackets DX-1000 series offers DIN-Rail Mount that customer can install system on the DIN Rail. 1. Please refer to section 3.6 Wall Mount Brackets to install mounting bracket at both sides of system. 2. Fasten 2 DIN rail mounting clips to mounting brackets on both sides with provided 4 screws as illustrated. 65

66 3. Clip the system into DIN rail as illustrated by the following steps. (1) Have lower end of mounting clip snaps into the DIN rail. (2) Press the system toward to have upper end of mounting clip snaps into the other side of DIN rail VESA Mount DX-1000 series supports VESA mounting that customer can mount system with panel complying with VESA 75mm and 100 mm standard for various usage. 66

67 1. The following picture illustrates the installation of DX-1000 series on a VESA stand. Align the 4 screw holes of VESA stand with the screw holes on bottom side of system. Fasten 4 screws to fix it. 2. Provided below is mounted with VESA stand. 67

68 3.9 Side Mount Brackets DX-1000 series offers Side Mount that customer can install system to the right or left side of wall to create effective of space. 1. The mounting holes are at the bottom of system. Fasten the 8 screws to fix the side mount bracket with system together. 68

69 2. Fasten the screws through the bracket mounting hole to mount system on the wall. 69

70 Chapter 4 BIOS Setup

71 4.1 BIOS Introduction The BIOS (Basic Input/Output System) is a program located on a Flash Memory on the motherboard. When you start the computer, the BIOS program will gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. BIOS Setup Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing <Ctrl>, <Alt> and <Delete> keys. Control Keys < > < > < > < > <Esc> <Enter> <Page Up/+> <Page Down/-> <Tab> <F1> <F2> <F3> <F10> Move to select screen Move to select item Quit the BIOS Setup Select item Increases the numeric value or makes changes Decreases the numeric value or makes changes Select setup fields General help Previous value Load Optimized defaults Save configuration and Exit Main Menu The main menu lists the setup functions you can make changes to. You can use the arrow keys ( ) to select the item. The on-line description of the highlighted setup function is displayed at the bottom of the screen. Sub-Menu If you find a right pointer symbol appears to the left of certain fields that means a sub-menu can be launched from this field. A sub-menu contains additional options for a field parameter. You can use arrow keys ( ) to highlight the field and press <Enter> to call up the sub-menu. Then you can use the control keys to enter values and move from field to field within a sub-menu. If you want to return to the main menu, just press the <Esc >. 71

72 4.2 Main Setup Press <Del> key to enter BIOS CMOS Setup Utility, the Main Menu (as shown below) will appears on the screen. Use arrow keys to move among the items and press <Enter> to accept or enter a sub-menu System Date Set the date. Please use <Tab> to switch between date elements System Time Set the time. Please use <Tab> to switch between time elements. 72

73 4.3 Advanced Setup This section allows you to configure and improve your system and allows you to set up some system features according to your preference CPU Configuration 73

74 Intel (VXM) Virtualization Technology Enables or disables Intel Virtualization Technology, which will allow a platform to run multiple operating systems and applications in independent partitions. With virtualization, one computer system can function as multiple virtual systems. Active Process Cores Allows you to choose the number of active processor cores. Configuration options: [All] [1] SATA And RST Configuration SATA Controller(s) [Enabled] Enables or disables SATA device. SATA Mode Selection [AHCI] Allows you to select which mode SATA controller will operates. Configuration options: [AHCI], [RAID] 74

75 Serial ATA Port 0 Port 0 [Enabled] Enables or disables SATA Port 0. Hot Plug [Disabled] Enables or disables Port0 as Hot Pluggable. Serial ATA Port 1 Port 1 [Enabled] Enables or disables SATA Port 1. Hot Plug [Disabled] Enables or disables Port1 as Hot Pluggable. Serial ATA Port 2 Port 2 [Enabled] Enables or disables SATA Port 2. Serial ATA Port 3 Port 3 [Enabled] Enables or disables SATA Port 3. Serial ATA Port 4 Port 4 [Enabled] Enables or disables SATA Port 4. Serial ATA Port 5 Port 5 [Enabled] Enables or disables SATA Port 5. 75

76 Software Feature Mask Configuration RAID OROM(Option ROM) / RST(Intel Rapid Storage Technology) driver will refer to the software feature configuration to enable or disable the storage features. HDD Unlock Enables or disables HDD Unlock. LED Locate Enables or disables LED Locate. 76

77 4.3.3 PCH-FW Configuration ME State Enables or disables PCH-FW Configuration Manageability Features State Enables or disables ME Unconfig on RTC Clear Enables or disables Firmware Update Configuration Configure Management Engine Parameters Me FW Image Re-Flash Enables or disables ME firmware Image Re-Flash function. 77

78 4.3.4 ACPI Settings Enable ACPI Auto Configuration [Disabled] Enables or disables BIOS Advanced Configuration Power Interface (ACPI) auto configuration. Enable Hibernation [Enabled] Enables or disables system ability to hibernate state (OS/S4 state). This option may not be effective with some OS. ACPI Sleep State [S3 (Suspend to RAM)] Allows users to select the highest Advanced Configuration Power Interface (ACPI) sleep state that system will enter when suspend button is pressed. [Suspend Disabled]: Disables entering suspend state. [S3 (suspend to RAM)]: Enables suspend to RAM state. Lock Legacy Resources [Disabled] Enables or disables Lock Legacy Resources. S3 Video Repost [Enabled] Enable or disable S3 Video Repost. 78

79 4.3.5 F81866 Super IO Configuration Set Parameters of Serial Ports. User can Enable/Disable the serial port and Select an optimal settings for the Super IO Device Serial Port 1~6 Configuration. 79

80 Serial Port [Enabled] Enables or disables serial port. Change Settings [Auto] Allows you to change the IO Address & IRQ settings of the specified serial port. Onboard Serial Port 1~6 Mode [RS232] Allows you to select Serial Port Mode. Configuration options: [RS232] [RS422/RS485 Full Duplex] [RS485 Half Duplex] Watch Dog Function You can setup the system watch-dog timer, a hardware timer that generates a reset when the software that it monitors does not respond as expected each time the watch dog polls it. Watch Dog [Disabled] Enables or disables watch dog function. Watch Dog Mode [Sec] Allows to set watchdog timer unit <Sec> or <Min>. Watch Dog Timer [0] Allows you to set watchdog timer s value in the range of 0 to Hardware Monitor This screen displays the current status of all monitored hardware devices/components such as voltages, temperatures and all fans speeds. 80

81 PC Health Status PWM Fan Function [Enabled] Enables or disables PWM Fan function S5 RTC Wake Settings Wake system from S5 [Disabled] Enables or disables wake system from S5 (soft-off state). [Disabled]: Disables wake system from S5. [Fixed Time]: Sets a fixed time (HH:MM:SS) to wake system from S5. [Dynamic Time]: Sets a increase minute(s) from current time to wake system from S5. 81

82 4.3.8 Serial Port Console Redirection Console Redirection Allow users to enable or disable COM0, COM1, COM2, COM3, COM4, COM5 console redirection function. COM0 = Serial Port 1 COM1 = Serial Port 2 COM2 = Serial Port 3 COM3 = Serial Port 4 COM4 = Serial Port 5 COM5 = Serial Port 6 82

83 4.3.9 Network Stack Configuration Network Stack [Disabled] Enables or disables UEFI Network Stack CSM Configuration This option controls legacy/uefi ROMs priority. 83

84 CSM Support [Enabled] Enables or disables compatibility support module. Boot option filter [UEFI and Legacy] Allows you to select which type of operating system to boot. [UEFI and Legacy]: Allows booting from operating systems that support legacy option ROM or UEFI option ROM. [Legacy only]: Allows booting from operating systems that only support legacy option ROM. [UEFI only]: Allows booting from operating systems that only support UEFI option ROM. Network PXE [Do not launch] Controls the execution of UEFI and Legacy PXE (Network Preboot execution Environment) option ROM. [Do not launch]: Disables option ROM execution. [UEFI]: Enables UEFI option ROM only. [Legacy]: Enables legacy option ROM only. Storage [Legacy] Controls the execution of UEFI and Legacy Storage option ROM. [Do not launch]: Disables option ROM execution. [UEFI]: Enables UEFI option ROM only. [Legacy]: Enables legacy option ROM only. Video [Legacy] Controls the execution of UEFI and Legacy Video option ROM. [Do not launch]: Disables option ROM execution. [UEFI]: Enables UEFI option ROM only. [Legacy]: Enables legacy option ROM only. Other PCI devices [Do not launch] Allows users to determine option ROM execution policy for devise other than network, storage, or video. 84

85 USB Configuration Legacy USB Support [Enabled] This item allows you to enable or disable legacy USB support. When set to [Auto], legacy USB support will be disabled automatically if no USB devices are connected. XHCI Hand-off [Enabled] Enables or disables XHCI (USB3.0) hand-off function. Use this feature as a workaround for operating systems without XHCI hand-off support. USB Mass Storage Driver Support [Enabled] Enables or disables USB mass storage driver support. 85

86 4.4 Chipset Setup This section allows you to configure chipset related settings according to user s preference System Agent (SA) Configuration 86

87 VT-d [Enabled] Enables or disables Intel Virtualization Technology for Directed I/O (VT-d) capability. Above 4GB MMIO BIOS assignment [Diabled] Enables or disables Above 4GB Memory Mapped IO BIOS assignment. This is disabled automatically when Aperture Size is set to 2048MB. Memory Configuration This item displays detailed memory configuration in the system. Graphics Configuration Primary Display [Auto] Allows users to select which graphics device should be primary display or select SG for switchable graphics. Configuration options: [Auto] [IGFX] [PEG] [PCIe] Internal Graphics [Auto] Allows users to enable or disable Internal Graphics. Configuration options: [Auto] [Disabled] [Enabled] PCH-IO Configuration 87

88 PCI Express Configuration PCI Express (Mini PCIe1 (CN3)) PCI Express (Mini PCIe1 (CN3)) [Enabled] Enables or disables PCI Express Root Port. PCIeSpeed [Auto] Allows you to select PCI Express port speed. Configuration options: [Auto] [Gen1] [Gen2] [Gen3]. PCI Express (Mini PCIe1 (CN4)) PCI Express (Mini PCIe1 (CN4)) [Enabled] Enables or disables PCI Express Root Port. PCIeSpeed [Auto] Allows you to select PCI Express port speed. Configuration options: [Auto] [Gen1] [Gen2] [Gen3]. PCI Express (Mini PCIe1 (CN5)) PCI Express (Mini PCIe1 (CN5)) [Enabled] Enables or disables PCI Express Root Port. PCIeSpeed [Auto] Allows you to select PCI Express port speed. Configuration options: [Auto] [Gen1] [Gen2] [Gen3]. PCI Express (Mini PCIe1 (CN6)) PCI Express (Mini PCIe1 (CN6)) [Enabled] Enables or disables PCI Express Root Port. PCIeSpeed [Auto] Allows you to select PCI Express port speed. Configuration options: [Auto] [Gen1] [Gen2] [Gen3]. 88

89 LAN i219lm Controller [Enabled] Enables or disables i219lm LAN Controller. Wake on LAN Enabled [Enabled] Enables or disables integrated LAN Wake On LAN function. LAN i210at Controller [Enabled] Enables or disables i210at LAN Controller. Power Failure [Keep last state] Allows you to specify which power state system will enter when power is resumed after a power failure (G3 state). [Always on]: Enters to power on state. [Always off]: Enters to power off state. [Keep last state]: Enters to the last power state before a power failure. CN3 msata Function Switch [Mini-PCIe] Allows you to change Mini PCIe1 (CN3) as [Mini-PCIe] or [msata]. CN3 USB3 Function Switch [Disabled] Enables or disables CN3 USB3 Controller. CN4 msata Function Switch [Mini-PCIe] Allows you to change Mini PCIe1 (CN4) as [Mini-PCIe] or [msata]. CN4 USB3 Function Switch [Disabled] Enables or disables CN4 USB3 Controller. CN5 msata Function Switch [Mini-PCIe] Allows you to change Mini PCIe1 (CN5) as [Mini-PCIe] or [msata]. CN6 msata Function Switch [Mini-PCIe] Allows you to change Mini PCIe1 (CN6) as [Mini-PCIe] or [msata]. Amplifier Function [Enabled] Enables or disables Amplifier Function. 89

90 4.5 Security Setup This section allows you to configure BIOS security settings Administrator Password Allows you to set Administrator Password to control access to the BIOS Setup utility User Password Allows you to set User Password to control access to the system at boot and to the BIOS Setup utility. 90

91 4.6 Boot Setup This section allows you to configure Boot settings Setup Prompt Timeout Use this item to set number of seconds ( ) to wait for setup activation key Bootup NumLock State Allows you to set NumLock key to [On] or [Off] state when system boots up Quiet Boot Allows you to enable or disable Quiet Boot function Fast Boot Allows you to enable or disable Fast Boot function. If enabled, system boots with initialization of a minimal set of devices required to launch active boot option New Boot Option Policy Allows you to change New Boot Option Policy. Configuration options: [Default] [Place First] [Place Last] Hard Drive BBS Priority Allows you to set the order of the legacy devices in this group. 91

92 4.7 Save & Exit Save Changes and Exit This item allows you to exit system setup after saving changes Discard Changes and Exit This item allows you to exit system setup without saving changes Save Changes and Reset This item allows you to reset the system after saving changes Discard Changes and Reset This item allows you to reset system setup without saving any changes Save Changes This item allows you to save changes done so far to any of the setup options Discard Changes. This item allows you to discard changes done so far to any of the setup options Restore Defaults This item allows you to restore/ load default values for all the setup options Save as User Defaults This item allows you to save the changes done so far as user defaults Restore User Defaults This item allows you to restore the user defaults to all the setup options. 92

93 Chapter 5 Product Application (For DIO only)

94 This chapter describes the DIO applications. 5.1 Digital I/O (DIO) Application This section describes DIO application of the product. The content and application development are better understood and implemented by well experienced professionals or developers Digital I/O Programming Guide Pins for Digital I/O Item Standard Item Standard GPIO70 (Pin103) GPIO80 (Pin111) GPIO71 (Pin104) GPIO81 (Pin112) GPIO72 (Pin105) GPIO82 (Pin113) GPIO73 (Pin106) GPIO74 (Pin107) DI GPIO83 (Pin114) GPIO84 (Pin115) DO GPIO75 (Pin108) GPIO85 (Pin116) GPIO76 (Pin109) GPIO86 (Pin117) GPIO77 (Pin110) GPIO87 (Pin118) Programming Guide To program the F81866A configuration registers, the following configuration procedures must be followed in sequence: (1) Enter the Extended Function Mode (2) Configure the configuration registers (3) Exit the Extended Function Mode The configuration register is used to control the behavior of the corresponding devices. To con- figure the register, using the index port to select the index and then writing data port to alter the parameters. The default index port and data port are 0x4E and 0x4F, respectively. To enable configuration, the entry key 0x87 must be written to the index port. To disable configuration, write exit entry key 0xAA to the index port. Following is an example to enable configuration and disable configuration by using debug. -o 4e 87 -o 4e 87 (enable configuration) -o 4e aa (disable configuration) 94

95 Relative Registers To program the F81866A configuration registers, the following configuration procedures. 95

96 96

97 Sample Code in C Language Control of GP70 to GP77 (DI1 ~ DI8) #define AddrPort 0x4E #define DataPort 0x4F <Enter the Extended Function Mode> WriteByte(AddrPort, 0x87) WriteByte(AddrPort, 0x87) //Must write twice to entering Extended mode <Select Logic Device> WriteByte(AddrPort, 0x07) WriteByte(dataPort, 0x06) //Select logic device 06h <Input Mode Selection> //Set GP70 to GP77 input Mode WriteByte(AddrPort, 0x80) // Select configuration register 80h WriteByte(DataPort, 0x0X) //Set (bit 0~7) = 0 to select GP 70~77 as Input mode. <input Value> WriteByte(AddrPort, 0x82) // Select configuration register 82h ReadByte(DataPort, Value) // Read bit 0~7(0xFx)= GP70 ~77 as High. <Leave the Extended Function Mode> WriteByte(AddrPort, 0xAA) 97

98 Control of GP80 to GP87 (DO1 ~ DO8) #define AddrPort 0x4E #define DataPort 0x4F <Enter the Extended Function Mode> WriteByte(AddrPort, 0x87) WriteByte(AddrPort, 0x87) //Must write twice to entering Extended mode <Select Logic Device> WriteByte(AddrPort, 0x07) WriteByte(DataPort, 0x06) // Select logic device 06h <Output Mode Selection> //Set GP80 to GP87 output Mode WriteByte(AddrPort, 0x88) // Select configuration register 88h WriteByte(DataPort, (0xXF)) //Set (bit 0~7) = 1 to select GP 80 ~87 as Output mode <Output Value> WriteByte(AddrPort, 0x89) // Select configuration register 89h WriteByte(DataPort, Value) // Set bit 0~7=(0/1) to output GP 80~87 as Low or High <Leave the Extended Function Mode> WriteByte(AddrPort, 0xAA) Change base address <Enter the Extended Function Mode> WriteByte(AddrPort, 0x87) WriteByte(AddrPort, 0x87) //Must write twice to entering Extended mode <Select Logic Device> WriteByte(AddrPort, 0x07) WriteByte(dataPort, 0x06) //Select logic device 06h WriteByte(AddrPort, 0x60) // Select configuration register 60h (High Byte address) WriteByte(DataPort, ( 0x0A)) WriteByte(AddrPort, 0x61) // Select configuration register 61h (Low Byte address) WriteByte(DataPort, ( 0x00)) <Leave the Extended Function Mode> WriteByte(AddrPort, 0xAA) Cincoze default DIO Port base address is set to 0x0A00h 98

99 DATA Bit Table (DIO) bit Value 1 /h bit Value 2 /h bit Value 4 /h = DI1 (Base address +3) (0xA03) = DI2 (Base address +3) (0xA03) = DI3 (Base address +3) (0xA03) bit Value 8 /h = DI4 (Base address +3) (0xA03) bit Value 10 /h = DI5 (Base address +3) (0xA03) bit Value 20 /h bit Value 40 /h = DI6 (Base address +3) (0xA03) = DI7 (Base address +3) (0xA03) bit Value 80 /h = DI8 (Base address +3) (0xA03) 99

100 bit Value 1 /h bit Value 2 /h bit Value 4 /h = DO1 (Base address +2) (0xA02) = DO2 (Base address +2) (0xA02) = DO3 (Base address +2) (0xA02) bit Value 8 /h = DO4 (Base address +2) (0xA02) bit Value 10 /h = DO5 (Base address +2) (0xA02) bit Value 20 /h bit Value 40 /h = DO6 (Base address +2) (0xA02) = DO7 (Base address +2) (0xA02) bit Value 80 /h = DO8 (Base address +2) (0xA02) 100

101 DIO I/O Port Address (Default Address 0xA00) DI8 DI7 DI6 DI5 DI4 DI3 DI2 DI1 Pin Definition Data Bits Digital Input 0xA03 DIO I/O Port address DO8 DO7 DO6 DO5 DO4 DO3 DO2 DO1 Pin Definition Data Bits Digital Output 0xA02 DIO I/O Port address 5.2 (DIO) Hardware Specification XCOM+ : Isolated power in V+ XCOM- : Isolated power in V- Isolated power in DC voltage : 5~48V 8x Digital Input (Source Type) Input Signal Voltage Level - Signal Logic 0 : XCOM+ = 5V, Signal Low - V- < 0.4V XCOM+ > 5V, V+ - Signal Low > 4.6V - Signal Logic 1 : > XCOM+ - 3V Input Driving Sink Current : - Minimal : 1 ma - Normal : 5 ma 8x Digital Output (Open Drain) - DO Signal have to pull up resistor to XCOM+ for external device, the resistance will affect the pull up current - Signal High Level : Pull up resistor to XCOM+ - Signal Low Level : = XCOM- - Sink Current: 1A (Max) 101

102 5.2.1 DIO Connector Definitions DIO1: Digital Input Connector Connector Type: Terminal Block 1X10 10-pin, 3.5mm pitch Pin Definition XCOM+ DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 XCOM- Pin 1 DIO2: Digital Output Connector Connector Type: Terminal Block 1X10 10-pin, 3.5mm pitch Pin Definition XCOM+ DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8 XCOM- Pin 1 102

103 Chapter 6 Optional Module Pin Definitions and Settings

104 6.1 Location of the Connectors and Switches Model No. CFM-IGN01 CMI-COM01/UB0903 CMI-DIO01/UB0918 Description CFM Module with Power Ignition Sensing Control Function, Select 12V/24V CMI Module with 2x RS232/422/485, 1x Universal Bracket CMI Module with 16x Optical Isolated DIO (8 in/8 out), 1x Universal Bracket 6.2 CFM-IGN Power Ignition Module Connector Location SW2: IGN Function Switch Set shutdown delay timer when ACC is turned off Pin 1 Pin 2 Pin 3 Pin 4 Definition ON ON ON 0 second ON ON OFF 1 minute ON OFF ON 5 minutes ON OFF OFF ON OFF ON ON OFF 10 minutes 30 minutes OFF ON OFF 1 hour OFF OFF ON 2 hours OFF OFF OFF Reserved (0 second) 24V_12V_1: 12V / 24V Car Battery Switch Pin Definition V Car Battery Input V Car Battery Input 104

105 6.3 CMI-COM Module Connector Definition and Settings COM5 / COM6: RS232 / RS422 / RS485 Connector Connector Type: 9-pin D-Sub COM5 / COM6 DB9 Pin RS232 Definition RS422 / 485 Full Duplex Definition RS485 Half Duplex Definition 1 DCD TX- DATA- 2 RXD TX+ DATA+ 3 TXD RX+ 4 DTR RX- 5 GND 6 DSR 7 RTS 8 CTS 9 RI COM5/6 Voltage Function Setting : Pin Define SW2 Switch Location Function DIP1 DIP2 0V(RI) ON (Default) ON (Default) SW2 COM5 5V ON OFF ON 12V OFF OFF OFF Location Function DIP3 DIP4 0V(RI) ON (Default) ON (Default) SW2 COM6 5V ON OFF ON 12V OFF OFF OFF 105

106 6.4 CMI-M12 LAN Module Pin Definitions Connector Type: M12 A coded 8pin connector Pin Definition Pin Definition 1 2_LAN1_0+ 2 2_LAN1_0-3 2_LAN1_1+ 4 2_LAN1_2+ 5 2_LAN1_2-6 2_LAN1_1-7 2_LAN1_3+ 8 2_LAN1_3-6.5 CMI-M12 PoE Module Pin Definitions Connector Type: M12 A coded 8pin connector POE type: Midspan (B-Type) Pin Definition Pin Definition 1 2_LAN1_0+ 2 2_LAN1_0-3 2_LAN1_1+ 4 2_LAN1_2+(Power PIN) 5 2_LAN1_2-(Power PIN) 6 2_LAN1_1-7 2_LAN1_3+(Power PIN) 8 2_LAN1_3-(Power PIN) 106

107 Cincoze Co., Ltd. All rights reserved. The Cincoze logo is a registered trademark of Cincoze Co., Ltd. All other logos appearing in this catalog are the intellectual property of the respective company, product, or organization associated with the logo. All product specifications and information are subject to change without notice. 107