SD Series. modular stepping drives. Rack mounting stepper drives with AC or DC power input. Automation. SD series features

Transcription

1 SD modular stepping drives Rack mounting stepper drives with AC or DC power input SD drives are full/half and ministepping modules that offer high standards of performance for low to medium power applications. Delivering nominal currents of 2A, 3A and 5A, they provide the benefits of bipolar chopper operation at an economic price. These rack-mounting modular drives are extremely flexible in terms of power supply requirements and motor compatibility. They may be powered directly from the secondary winding of an isolating transformer or from unregulated DC supplies. Motor current is programmable using simple jumper links on the card, with selectable automatic current reduction at standstill. On standard drives the resolution is selectable between 2 and 4 steps/rev, whilst the SD15M offers four selectable resolutions up to 4 steps/rev. This makes it the perfect choice for applications requiring smooth rotation over a wide speed range. Step and direction pulses may be derived from a usersupplied pulse source, a rack-mounted indexer card, a standalone Parker indexer or an integral clock generator on the drive. The SD15M clock generator compensates automatically for resolution changes so that the preset shaft speed remains constant regardless of the selected resolution. Features common to the entire SD range include short circuit protection across and between phases, overvoltage protection and a remote de-energise facility. Versions with an integral power dump are available - please see below for further details. A range of pre-wired rack systems is available to house SD drives together with optional indexers. Please refer to the information on rack systems later in this catalogue. Regenerative power dump option Applications which involve rapid deceleration of high-inertia loads may require that the drive is fitted with a power dump circuit. The SD15MD and WD versions have the same electrical specification as the SD15 but incorporate a power dump with a continuous rating of 15 watts (17 watts peak). The MD or WD will be required if the deceleration time in seconds is less than {Jω 2 -.3} where ω is the maximum speed in revolutions per second and J is the total system inertia in Kg m 2. If the expression in brackets is negative, no power dump is required. The power dump is strongly recommended if a 16-size stepper motor is being used. SD series features Bipolar switch-mode drive with integral oscillator High-reliability, surface mount design 6VDC motor supply for improved high-speed torque Selectable resolutions up to 4 steps/rev Output current up to 5A per phase Operation from AC or DC supplies Phase-to-phase short circuit protection Motor current programmable by jumper links Selectable automatic current reduction at standby Regenerative power dump option Standard 3U rack mounting Compatible with standard 2/4 phase stepper motors 18

2 SD specifications Parameter Value Power Motor Supply Voltage to VAC or 24 to 6 VDC Motor Supply Current SD12-1.5A, SD13-2.5A, SD15 & SD15M - 5A Logic Supply Voltage VAC or +24 VDC at 35 ma max Amplifier Type Bipolar chopper Motor Resolution (selectable) SD12, SD13 & SD15-2 or 4 steps/rev SD15M - 4, 1, 2 or 4 steps/rev Short Circuit Protection Phase-to-phase Nominal Output Current SD12 2A/phase, SD13 3A/phase, SD15 & SD15M 5A/phase Current may be set to lower values by jumpers Maximum Stepping Rates 1 2 step/rev, 2 4 step/rev (2 4 step/rev for SD15M) Nominal Chopping Frequency 2 khz Edge Connector 32-way DIN Type D Physical Dimensions See diagram Rack mounting data Front panel 14HP wide, 3U high (see optional panels below) Weight 2g Command Interface SD Drive only via SDC Opto Motherboard Input Impedance/current 4K7 to +12VDC 2mA max. Input Logic Low Level <2.V TTL, <.8V Input Logic High Level 1V to 12V or open circuit TTL, >3.5V Clock (Step) Input Low-going pulse, 1µS min. Differential TTL pulse, 1µS min. (2.5µS for SD15M) (1µS for SD15M) Output Circuit NPN open-collector, Isolated NPN open-collector, 25V OFF max, 15mA ON max. 12V OFF max, 5mA ON max. Internal oscillator speed ranges SD12, SD13, SD15 SD15M Slow (not ramped) 3 1 steps/sec 3 13 rpm (independent of resolution) Fast (ramped) 6 2, steps/sec 6 3, rpm (independent of resolution) Acceleration Time 6 ms Deceleration Time 3 ms acceleration and deceleration times may be increased by additional capacitor Environmental Operating Temperature to 5 C Storage Temperature 4 to 85 C Humidity to 95% non-condensing Motors Type 2 phase hybrid; 4, 6 or 8 leads Minimum Inductance 1 mh Recommended induct. range 1-1mH Optional front panels FP36 for SD12; FP37 for SD13; FP38 for SD15; FP48 for SD15M Transformers T193 (3VA); T194 (6VA) 19

3 SD performance & dimensions Typical performance data.6 SD13 with ST57-51P motor SD15 with ST57-83P motor SD15 with ST57-12P motor* SD15 with ST83-62P motor SD15 with ST83-93P motor 3. SD15 with ST83-135P motor * connection available only on flying lead version of this motor SD dimensions (mm)

4 SC/CN rack systems & power supplies A range of pre-assembled rack systems for SD and CD series stepper drives To simplify the installation and commissioning of rackmounted drive modules, Parker offer a range of preassembled rack systems to house up to six drives. The system is based on individual motherboards for each drive, with additional motherboards catering for power supplies and control cards. Each rack system is fitted with the appropriate number of motherboards according to the module complement, allowing all external connections to be made via screw terminals or plug-in connectors. All assemblies are based on the standard Euro-rack system and are 3U high (132mm). Module and panel widths are always quoted in horizontal pitches (HP), the width of a standard rack being 84HP. For example, SD drive front panels are 14HP wide, so six panels will occupy the full rack width of 84HP. All drive motherboards used in SC and CN series racks incorporate opto-isolation of the control signals, making them directly compatible with the Parker indexers listed later in this catalogue. SC series racks for SD drives The SD drive operates directly from an isolating transformer and therefore requires no separate power supply module. This allows up to six SD drives to be housed in a single SC series rack. When combined with IFX indexer cards, the maximum number of axes per rack is three. CN series racks for CD drives CD6M and CD8M drives require a separate PM2CN power supply module, which is 24HP wide. This still allows room for six drives in a CN series rack since each drive front panel is only 1HP wide. When combined with IFX indexer cards, up to three axes can be accommodated in a single rack. PM2CN power supply module The PM2CN offers a convenient and economic method of powering CD series drives. All necessary components are included with the exception of the mains transformer which is mounted separately from the rack. The power module has an output current rating of 16A DC at a bus voltage of 12V. A regenerative power dump circuit is included, and the module comes complete with a 24HP front panel. The AC input to the PM2CN may be single or three phase. Transformers There is a range of standard transformers available to power SD or CD series drives. The required transformer size depends partly on motor size, shaft power demand and duty cycle, however the quantities listed in the table form a useful guide. These are based on no more than half the axes being in motion at any one time. All single-phase transformers may be operated from 115V and 23V supplies. Models TO181 and TO182 have fourwinding primaries which also permit line-to-line connection on 4V 3-phase supplies. Ordering information SC and CN racks can be supplied as drive-only versions or for drives with indexer cards. Please refer to the order codes and select the appropriate rack according to the number of axes required. Standard rack systems do not allow for a mix of drives with and without indexer cards, however other combinations are available to special order. The rack order code refers to the rack assembly only; all plug-in drive modules, power supplies, front panels and transformers are ordered separately. When all parts are ordered at the same time, the rack will be supplied with all modules and front panels fitted. Order codes SC 1 SC: for SD drives : drives only CN: for CD drives 2X/RS232C: drives Number of axes with IFX indexer cards Example - SC3: three SD drives CN22X/RS232C: two CD drives with IFX cards 24

5 SC/CN rack systems & power supplies 1-6 SD or 1-3 SD+IFX 14 HP wide each SC & CN rack dimensions (mm) SC- Racks CD or 1-3 CD+IFX 1 HP wide each PM2CN 24 HP wide Top view, all types 465 CN- Racks Ordering front panels Optional front panels are available for all drive modules as well as blank panels to cover control cards or unused spaces in the rack. Please note that these panels are not included with the drive and must be ordered separately if required. Panel type Width Part No. SD12 14HP FP36 SD13 14HP FP37 SD15 14HP FP38 SD15M 14HP FP48 CD6M 1HP FP52 CD8M 1HP FP53 Blank 1HP FP55 Blank 14HP FP39 Blank 2HP FP54 Completing the rack The table below shows the number of blank panels required for each rack type in order to cover control cards or empty slots in the rack. Rack type Number of blank panels required FP55 FP39 FP54 SC1, SC12X 5 SC2, SC22X 4 SC3, SC32X 3 SC4 2 SC5 1 CN1, CN12X 1 2 CN2 2 CN3 1 1 CN4 1 CN5 1 CN22X 2 1 CN32X 3 Transformers for rack-mounting drives Models for SD drives Models for CD drives TO193 TO194 TO181 TO182 TO185 TO186 AC input range 11-24v 11-24v 9-48v 9-48v 18-48v 18-48v Single/three phase DC bus voltage VA rating Max. number of drives* 3 x SD12 6 x SD12 8 x CD6M 4 x CD6M 8 x CD6M 11 x CD6M 2 x SD13 4 x SD13 6 x CD8M 3 x CD8M 6 x CD8M 8 x CD8M 1 x SD15 2 x SD15 Dimensions w x d x h 117x117x x168x x215x x195x234 32x132x319 38x14x359 Weight kg * Assumes 5% duty cycle. Larger numbers of drives may be accommodated at lower duty cycles 25