Quad Small Form factor Pluggable Plus (QSFP/QSFP+)

Transcription

1 Quad Small Form-factor Pluggable Plus (QSFP/QSFP+) Product Description Lightwave Link Inc. Quad Small Form-factor Pluggable (QSFP) product is a new high speed pluggable I/O interface products. This interconnecting system offers 4 channels and maximum bandwidth of 40Gbps which are based on the proprietary technique Silicon Optical Bench (SiOB). This module provides high performance and excellent efficiency in the optical communication. Features Compliant with 40G Ethernet IEEE 802.3ae 40GBASE-SR4 standards QSFP footprint (Quad small form-factor, pluggable) Applications 40GBASE-SR4 Ethernet links Infiniband QDR and DDR interconnects Client-side 40G Telecom connections Supports 40 Gbps data rate links of up to 150 meters Compliant with QDR/DDR Infiniband data rates Hot pluggable electrical interface RoHS-6 Compliant (lead-free)

2 Absolute Maximum Rating Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operation Conditions. It should not be assumed that limiting values of more than one parameter can be applied to the module concurrently. Exposure to any of the Absolute Maximum Ratings for extended periods can adversely affect reliability. Parameter Symbol Min Typical Max Unit Note Storage Temperature Ts 0 85 Relative Humidity RH 0 85 % ESD Specifications ESD EN , Criterion B 15KV air discharge during operation and 8kV direct contact discharge to the case without damage. JESD22-A114-B Signal pad 1000V HBM. Other pads 2KV HBM (SFF-8436 Rev 4.1) High speed signal contacts can withstand 1000V electrostatic discharge based on HBM without damage. All host contacts with exception of the module and host high speed signal contacts canl withstand 2KV electrostatic discharge based on HBM without damage. EMC Specifications Parameter Requirements Typ Unit Note EMC FCC Class B +6dB Margin +6dB

3 Recommended Operating Conditions Recommended operating conditions specify parameters for which the optical and electrical characteristics hold unless otherwise noted. Optical and electrical characteristics are not defined for operation outside the Recommended Operating conditions, reliability is not implied and damage to the module may occur for such operation over an extended period of time. Parameter Symbol Min Typical Max Unit Note Case Temperature Tc 0 70 Power Supply Voltage Vcc V Signal Rate per Channel Gbps Control Input Voltage High Vih 2 Vcc+0.3 V Control Input Voltage Low Vil V Two Wire Serial (TWS) Interface Clock 400 khz Rate Power Supply Noise 50 mvpp Receiver Differential Data Output Load 100 Ohms Fiber Length: 500 MHz km 50_m MMF m (OM2) Fiber Length: 2000 MHz km 50_m 100 m MMF (OM3) Fiber Length: 4700 MHz km 50_m 150 m MMF (OM4) Electrical Characteristics Parameter Symbol Min Typical Max Unit Note Power Consumption W Supply Current 320 ma Initialization Time t_ init 2000 ms 1 Notes: 1. Initialization Time is the time from when the supply voltages reach and remain above the minimum Recommended Operating Conditions to the time when the module enables TWS access. The module at that point is fully functional.

4 Optical Characteristics Optical Parameter Symbol Min Typical Max Unit Note Center Wavelength λ nm Receiver Characteristics Electrical Parameter Symbol Min Typical Max Unit Note Data Output Differential Peak-to-Peak ΔVDO pp mvpp Voltage Swing Output Total Jitter 60 ps BER PRBS31 QSFP+ Module Pad Assignments and Descriptions Pin Logic Symbol Description Plug Sequence Notes 1 GND Ground CML-I Tx2n Transmitter Inverted Data Input 3 3 CML-I Tx2p Transmitter Non-Inverted Data Input 3 4 GND Ground CML-I Tx4n Transmitter Inverted Data Input 3

5 6 CML-I Tx4p Transmitter Non-Inverted Data Input 3 7 GND Ground LVTTL-I ModSelL Module Select 3 9 LVTTL-I ResetL Module Reset 3 10 Vcc Rx +3.3V Power Supply Receiver LVCMOS-I/O SCL 2-wire serial interface clock 3 12 LVCMOS-I/O SDA 2-wire serial interface data 3 13 GND Ground CML-O Rx3p Receiver Non-Inverted Data Output 3 15 CML-O Rx3n Receiver Inverted Data Output 3 16 GND Ground CML-O Rx1p Receiver Non-Inverted Data Output 3 18 CML-O Rx1n Receiver Inverted Data Output 3 19 GND Ground GND Ground CML-O Rx2n Receiver Inverted Data Output 3 22 CML-O Rx2p Receiver Non-Inverted Data Output 3 23 GND Ground CML-O Rx4n Receiver Inverted Data Output 3 25 CML-O Rx4p Receiver Non-Inverted Data Output 3 26 GND Ground LVTTL-O ModPrsL Module Present 3 28 LVTTL-O IntL Interrupt 3 29 Vcc Tx +3.3V Power supply transmitter Vcc1 +3.3V Power supply LVTTL-I LPMode Low Power Mode 3 32 GND Ground CML-I Tx3p Transmitter Non-Inverted Data Input 3 34 CML-I Tx3n Transmitter Inverted Data Input 3 35 GND Ground CML-I Tx1p Transmitter Non-Inverted Data Input 3 37 CML-I Tx1n Transmitter Inverted Data Input 3 38 GND Ground 1 1 Note 1: GND is the symbol for signal and supply (power) common for the QSFP module. All are common within the QSFP+ module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal-common ground plane. Note 2: Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power supplies and shall be applied concurrently. Requirements defined for the host side of the Host Edge Card Connector are listed in Table. Recommended host board power supply filtering is shown in Host board power supply circuit. Vcc Rx Vcc1 and Vcc Tx may be internally connected within the

6 QSFP+ module in any combination. The connector pins are each rated for a maximum current of 500 ma. Recommended Host Board Power Supply Circuit Mechanical Design Diagram Unit: mm

7 Memory Map

8 Lower Memory Map (A0h) Address Description Default/Typical value 0 Identifier 0C 1 Reserved 00 2 Status 02 3 Rx LOS 00 4 Tx Fault 00 6 Temp High/Low alarm/warning 00 7 Vcc high/low alarm/ warning Reserved Supply voltage Reserved Tx bias Reserved Tx disable Reserved Module and Channel Masks Reserved Password Change Entry Area (optional) Password Entry Area (optional) 127 Page Select Byte 00

9 Upper Memory Map (A0h)

10 Address Description Default/Typical value 128 Identifier 0C 129 Ext. Identifier Connector 0C Module 10, 00, 00, 01, 40, 40, 04, Encoding BR, nominal Extended rate select Compliance Length(SMF) Length(OM3 50 um) Length(OM2 50 um) 0A 145 Length(OM um) Length(Copper) Device tech Vendor name 164 Extended Module Vendor OUI Vendor PN Vendor rev Wave length or Copper cable Attenuation 42, Wavelength tolerance 0F, A0 190 Max case temp CC_BASE Options Vendor SN Date Code 220 Diagnostic Monitoring Type Enhanced Options Reserved CC_EXT Vendor Specific

11 Upper Memory Map (A3h) Address Description Default/Typical value Temp high alarm Temp low alarm Temp high warning Temp low warning Vcc high alarm(3.6v) Vcc low alarm(3.0v) Vcc high warning(3.5v) Vcc low warning (3.1V) Rx power high alarm Optional Rx power low alarm Optional Rx power high warning Optional Rx power low warning Optional Tx bias high alarm Tx bias low alarm Tx bias high warning Tx bias low warning