APP 700 Technical Specification

Transcription

1 Issued: 12/12 Supersedes: 4/12 Description The APP 700 hardware series are especially designed for waste and clean water systems, both in construction and functionality. The RTUs¹ are developed to meet the demands of powerful flexible monitoring and control units and are prepared to work with various types of communication e.g. SCADA system, radio, ethernet cellular systems, dedicated and dialed-up telephone lines. The RTUs complies with the required electromagnetic emission and immunity standards. The front panel is user-friendly with self-instructive symbols. The RTUs are easy to install and commission. Part Number Front mounted APP Pump Controller APP Pump Controller APP Pump Controller Approved standards EMC emission standard EN EMC immunity standard EN LVD EN CSA C22.2 No UL Recognized File Number E Environment Operational temperature Storage temperature Humidity (non-condensing) F F 90 % RH Frontal mounting Front panel; front side IP 65 Front panel; backside IP 20 I/O unit IP 20 Frontal unit Size (L x W x H) Weight, total Mounting Surface seal Connectors 11.30x7.36x1.73 in 3.97 lb I/O unit Size (L x W x H) 11.65x10.67x2.44 in Weight, total 4.41 lb Mounting Wall Connectors 1 DB 37 Wire terminals 68, screw locked Cable Front panel to I/O unit Length Minimum bend radius Double shielded 37pole 6.56 ft 1.97 in Data Processing power Processor Elan SC520 (486) Executed word length, protected mode 32 bits Clock frequency 100 MHz Primary memory 16 Mbytes, D-RAM Secondary memory 16 Mbytes, flashdrive Battery backup Li, 3 V replaceble Watchdog Yes Character set The RTU is capable of handling Unicode characters however, the standard display can only show a limited set of characters. A special version is available for Simplified Chinese characters. Expandable system The possible number of inputs and outputs can be expanded to 600 when external RIO modules are connected. The RTU communicates with the RIO modules on a SIO field bus and an optional SIO driver is mounted in the RTU to run the SIO bus. ¹ Remote Terminal Unit

2 Communication The RTUs series is equipped with serial communication ports for local PC connection and modems. Accessories Standard software. Level sensor. Modem. Power supply. Over voltage protection. SIO driver. RIO modules. Overlays.

3 Technical data APP 721 Pump Controller APP 731 Pump Controller APP 741 Pump Controller Digital inputs All in puts are individually opto-isolated Locic 0: V Locic: 1: V, 6-30 ma Digital outputs All outputs are individually isolated Relay Outputs: 6 Type: Normally open, unprotected Max load: 2 A 250 VAC/DC Solid State Outputs: 2 Type: Normally open, unprotected Output: 100 ma, 250 VAC/DC Leakage current max: 0,01 ma Analogue inputs All inputs are individually opto-isolated Resolution: 12 bits Signal range: 4-20 ma Internal dynamic resistance, full scale: 50 Ohm Inaccuracy, full scale, typ.: 0.1% Voltage drop: 8V Communication Communication port: Bus communication: Optional SIO Driver Max number of I/O: User interface Display: LCD 2x20 character, LED backlight Push buttons: Alarm indications: LEDs Pump well indications: LEDs RTU status indications: LEDs Power supply Supply voltage: 24 VDC -15% % Current consumption (no load): 1 A Fuse: 2A Digitals inputs, max load: 0,5 A Analogue inputs, max load: 24 V, 80 ma = included

4 Interface Functions COM1 COM2 COM3 COM4 Dialled-up connection GSM modem Dialled-up connection external modem Radio communication, polled system Dedicated line modem Dedicated line 232/RS485 converter Service Ethernet adapter

5 Logical 0 = -3 to +5V Voltage drop = 8V Relay outputs Semiconductor outputs Logical 1 = 11-30V, 6-30mA 4-20mA 2A 250V AC/DC 100mA 250V AC/DC DIGITAL INPUTS ANALOGUE INPUTS DIGITAL OUTPUTS

6 11.65 in in 2.14 in APP/AP Front Front mounted mounted I/O Unit I/O Unit 9.50 in in in 1.73 in 5.85 in in in APP/AP Front Front mounted Operator panel panel 6.90 in 5.45 in in