Recommended Pick & Place Tools (Nozzles) for LEDs of OSRAM Opto Semiconductors Application Note

Transcription

1 Recommended Pick & Place Tools (Nozzles) for LEDs of OSRAM Opto Semiconductors Application Note In order to achieve the functionality of SMT mounting machines in production regarding equipment performance and accuracy with concomitant flexibility the use of device adapted pick & place tools (nozzles) is essential. A zero defect and in particular with LEDs a damage-free processing can only be reached and guaranteed by the use of an appropriate, individual nozzle. Therefore OSRAM Opto Semiconductors selected suitable nozzle for its specific LED product groups in co-operation with SIEMENS and verified their applicability with automated assembly test runs on SIPLACE pick and place machines. A catalogue with a linkage of the tools to the associated LED product family is listed on the following sides. Beside the SIPLACE number for the reference nozzle, the general design of the tools is represented. Beyond that numbers for possible alternatives are also indicated. More detailed information on the recommended nozzles, like technical drawings, material, etc. can be found in the product catalogue on the homepage of SIPLACE ( General it must be additionally ensured for the processing of LEDs that the process parameters are conformed to the package characteristics during assembly. If other nozzle or designs than the recommendations are used, it must be strictly observed, that especially the critical and optical relevant area (area over die/s and wire bond/s) is not loaded. If further information needed or support regarding the processing of LEDs please contact OSRAM Opto Semiconductors. Figure 1: General notice about the layout and content of the summary April, 2013 Page 1 of 14

2 Summary April, 2013 Page 2 of 14

3 April, 2013 Page 3 of 14

4 April, 2013 Page 4 of 14

5 April, 2013 Page 5 of 14

6 April, 2013 Page 6 of 14

7 April, 2013 Page 7 of 14

8 April, 2013 Page 8 of 14

9 April, 2013 Page 9 of 14

10 April, 2013 Page 10 of 14

11 April, 2013 Page 11 of 14

12 April, 2013 Page 12 of 14

13 Authors: Andreas Stich, Kurt-Jürgen Lang ABOUT OSRAM OPTO SEMICONDUCTORS OSRAM AG (Munich, Germany) is a wholly-owned subsidiary of Siemens AG and one of the two leading light manufacturers in the world. Its subsidiary, OSRAM Opto Semiconductors GmbH in Regensburg (Germany), offers its customers solutions based on semiconductor technology for lighting, sensor and visualization applications. OSRAM Opto Semiconductors has production sites in Regensburg (Germany) and Penang (Malaysia). Its headquarters for North America is in Sunnyvale (USA), and for Asia in Hong Kong. OSRAM Opto Semiconductors also has sales offices throughout the world. For more information go to DISCLAIMER PLEASE CAREFULLY READ THE BELOW TERMS AND CONDITIONS BEFORE USING THE INFORMATION. IF YOU DO NOT AGREE WITH ANY OF THESE TERMS AND CONDITIONS, DO NOT USE THE INFORMATION. The Information shown in this document was produced with due care, but is provided by OSRAM Opto Semiconductors GmbH as is and without OSRAM Opto Semiconductors GmbH assuming, express or implied, any warranty or liability whatsoever, including, but not limited to the warranties of correctness, completeness, merchantability, fitness for a particular purpose, title or non-infringement. In no event shall OSRAM Opto Semiconductors GmbH be liable - regardless of the legal theory - for any direct, indirect, special, incidental, exemplary, consequential, or punitive damages related to the use of the Information. This limitation shall apply even if OSRAM Opto Semiconductors GmbH has been advised of possible damages. As some jurisdictions do not allow exclusion of certain warranties or limitations of liability, the above limitations or exclusions may not apply. The liability of OSRAM Opto Semiconductors GmbH would in such case be limited to the greatest extent permitted by law. OSRAM Opto Semiconductors GmbH may change the Information at anytime without notice to user and is not obligated to provide any maintenance or support related to the Information. The Information is based on specific Conditions and, therefore, alterations to the Information cannot be excluded. April, 2013 Page 13 of 14

14 Any rights not expressly granted herein are reserved. Except for the right to use the Information included in this document, no other rights are granted nor shall any obligation be implied requiring the grant of further rights. Any and all rights or licenses to patents or patent applications are expressly excluded. Reproduction, transfer, distribution or storage of part or all of the contents of this document in any form without the prior written permission of OSRAM Opto Semiconductors GmbH is prohibited except in accordance with applicable mandatory law. September, 2010 Page 14 of 14