KasBar COB Tri 5. 5x15w 3in1 COB LEDs (RGB) USER MANUAL

Transcription

1 KasBar COB Tri 5 5x15w 3in1 COB LEDs (RGB) USER MANUAL

2 Table of Contents 1. Introduction Safety DMX Values & Function Display Operation Menu Guide & Operation DMX Connections Master/Slave Mode Operation Troubleshooting Technical Information

3 1. Introduction Ø Summary Thank you for purchasing the ColorKey KasBar COB Tri 5. Please read these instructions carefully before use. Operating this fixture according to these instructions is important to avoid any possible damage or accidents caused by misuse. Ø Product Introduction The ColorKey KasBar COB Tri 5 uses an aluminum housing and adopts a 5, 15W 3in1 (RGB) COB LEDs. This fixture features long life span, low power consumption, amazing color mixing and bright output. Each of the 3 colors can be independently controlled. Built-in modes include; dimming, strobe, gradual change, color fading, color pulse as well as other programs. This fixture uses a switching power supply that is light weight and requires minimal power consumption. This fixture also features universal protocol DMX-512. Ø Packing list 1x KasBar COB Tri 5 1x IEC Power Cable User Manual Warranty Card 1

4 2. Safety Ø Safety Notes Caution! Opening this unit voids warranty. Contact ColorKey for any service requests. Warning! To avoid electrical shock, be sure to disconnect power before any service or when moving or setting up the fixture. Caution! Avoid direct eye exposure with the fixture when on. Ø Safety instruction The KasBar COB Tri 5 has an automatic voltage switch and will automatically detect voltage when connected to power. Please be sure to check voltage is within the range of this fixtures specifications. Before use, check this fixture for damage that may have been caused during the shipping process. If damage is found to the unit, do not use and contact ColorKey immediately. This fixture is designed for indoor use only; operating this fixture outdoors may cause damage. This fixtures maybe mounted in any position provided there is adequate space for ventilation. 2

5 3. DMX Values & Functions Ø DMX 1 Channel Mode Channel Value Function Priority Off CH1 Ø DMX 3 Channel Mode 003 Red = 100% Red = 100% Green 039 Red Green = 100% Green =100% Red 075 Green =100% Green =100% Blue 111 Green Blue =100% Blue =100% Green 147 Blue =100% Blue =100% Red 183 Red Blue =100% Red =100% Blue 219 Red =100% Red =100% Green Blue 255 Red Green Blue =100% Channel Value Function Notes Priority CH Red 0-100% CH Green 0-100% CH Blue 0-100% 3

6 Ø DMX 7/8 Channel Mode Channel Value Function Notes Priority CH Master Dimmer 0-100% CH Red 0-100% CH Green 0-100% 1 CH Blue 0-100% CH N/A Not Used Strobe Speed (Fast-Slow) N/A Not Used Red Green Blue Red + Green Green + Blue Red + Blue Red + Green + Blue Program Program Program 3 CH Program Program Program Program Program Program Program Program Program Program Program Program Program Program Program Program 1-18 CH Speed (Slow-Fast) Use node setting Dimming 0 CH Dimming Dimming Dimming Dimming 4 4

7 Ø DMX 19/20 Channel Mode Channel Value Function Notes Priority CH Master Dimmer 0-100% CH Red 0-100% Pixel 1 CH Green 0-100% Pixel 1 CH Blue 0-100% Pixel 1 CH Red 0-100% Pixel 2 CH Green 0-100% Pixel 2 CH Blue 0-100% Pixel 2 CH Red 0-100% Pixel 3 1 CH Green 0-100% Pixel 3 CH Blue 0-100% Pixel 3 CH Red 0-100% Pixel 4 CH Green 0-100% Pixel 4 CH Blue 0-100% Pixel 4 CH Red 0-100% Pixel 5 CH Green 0-100% Pixel 5 CH Blue 0-100% Pixel 5 CH N/A Not Used Strobe (Fast Slow) N/A Not Used Red Green Blue Red + Green Green + Blue Red + Blue Red + Green + Blue Program 1 CH Program Program Program Program Program Program Program Program Program Program Program Program Program 14 5

8 Program Program 16 CH Program Program Program 1-18 CH Speed Adjustment (Slow-Fast) Use node Setting Dimming 0 CH Dimming Dimming Dimming Dimming 4 6

9 4. Display Operation DMX IN DMX OUT DMX IN/OUT MENU UP DOWN ENTER LED display 4 buttons Ø MENU : access the menu or return to a previous menu option Ø ENTER: select the current menu option Ø UP: menu selection or parameter increments Ø DOWN: menu selection or parameters decrease 7

10 5. Menu Guide & Operation Addr d001-d512 DMX Mode UEm UE2.0 Software Version node nod0-nod4 Speed Limitor LEd On/oFF Display on/off SoUA So.UA Sound Activated bl- - b000-b255 Blue Dimming MENU GL- - G000-G255 Green Dimming rl- - r000-r255 Red Dimming FLAS FL00-FL15 Strobe Mode (Fast-Slow) FAdE FA00-FA15 Color Fade (Fast-Slow) ASC AC00-AC15 Color Jump Change Pr- - Pr00-Pr15 Preset Selection 8

11 SP- - SP00-SP15 Program Speed (Fast-Slow) SLAU SL.AU Slave Mode CHnd 1/3/7/8/19/20 DMX Channel Mode 1.Operating instruction: To operate your unit in DMX mode, follow these steps: Ø Press MENU to activate display / return to main menu screen. Ø Press UP/DOWN until Addr is displayed. Ø Press ENTER to proceed. Display will flash indicating you have entered edit mode. Ø Press UP/DOWN to select desired DMX address. This will display as d001-d512. Ø Press ENTER to save and store your selections. The screen will stop flashing indicating you have exited edit mode. To select DMX Channel Mode, follow these steps: Ø Press MENU to activate display / return to main menu screen. Ø Press UP/DOWN until CHnd is displayed. Ø Press ENTER to proceed. Display will flash to indicating you have entered edit mode. Ø Press UP/DOWN to select desired DMX channel mode (3CH, 6CH, 10CH or 11CH). Ø Press ENTER to save and store your selections. The screen will stop flashing indicating you have exited edit mode. 9

12 To select Display On/Off, follow these steps: Ø Press MENU to activate display / return to main menu screen. Ø Press UP/DOWN until LED is displayed. Ø Press ENTER to proceed. Display will flash indicating you have entered edit mode. Ø Press UP/DOWN until desired selection is displayed ( On or OFF ). Ø Press ENTER to save and store your selections. The screen will stop flashing indicating you have exited edit mode. Note*** Display will remain on for approximately 2 minutes after the last button selection. When the display is off, press any button to activate display. 2. Details of Built-in Programs (Pr- -) Ø Press MENU to activate display / return to main menu screen. Ø Press UP / DOWN until Pr- - is displayed. Ø Press ENTER to proceed. Display will flash indicating you have entered edit mode. Ø Press UP / DOWN until desired selection is displayed (see chart below Pr- - ). Ø Press ENTER to save and store your selections. The screen will stop flashing indicating you have exited edit mode. Built-in Program Chart: Ø Pr32 - Pr35 are speed adjustable. SP00 is the fastest, SP15 is the slowest. Ø Pr00 - Pr63:R,G,B,A,W,UV single color or multi-colors lighting Ø Pr64-6 Color Change mode. Ø Pr65-6 Color Change + Strobe Ø Pr66 - Multi-Color Change Ø Pr67 - Multi-Color Change + Strobe 10

13 7. DMX Connections Ø DMX Cable: The KasBar COB Tri 5 can be controlled via DMX using a 3-pin XLR connection. The standard DMX connection is XLR is: one end connects to the male plug, and the other connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal Noted:In order to avoid failures and interference signal transmission,we connect a resistance120ω ( 1/4W ) at the end of the DMX connecting as below: Ø The Conversion between 3 pin and 5 pin XLR If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable 11

14 6. Master/Slave Mode Operation Master/Slave Master/Slave mode allows you to connect multiple units together using one (1) unit to control others in a chain. When a fixture is set to Master Mode, this unit will always act as a controlling unit until it is switched out of Master Mode. The Master unit will send out signal via DMX to Slave units which will react in synchronization. When a fixture is set into Slave Mode, this fixture will receive the Master signal. To ensure a fixture is in Slave Mode the fixture s display must read SLAV. To avoid master signal and DMX signal interference, do not connect DMX when using Master/Slave mode. If using a DMX run longer than 60 meters and/or over 32 units, a signal amplifier may be required. 8. Troubleshooting Problem Solutions u Make sure that the DMX cable is properly connected No DMX control u Make sure that the DMX controller is operational u Check the DMX cable for tears or breaks u Make sure that the fixture is in DMX mode Fixture does not respond to sound u Make sure that the fixture is in Sound Active mode. 12

15 9. Technical Information Input Voltage: AC 100V-260V/50-60HZ Power Consumption: 90W Lamp Spec: 5PC 15W 3in1(RGB) COB LED Refresh Rate :> 400HZ (32 BIT MCU processing, 16bit PWM) Control Mode: DMX512, Mater/Slave, Sound Activated, Stand Alone Channel: 1/3/7/8/19/20 Beam Angle: 80 Cooling Mode: Fan Cooling Anti-electricity Intension:>1.5KV Insulation Resistance:>2MΩ IP rated: IP20 Dimension: 270*225*405mm N.W.: 2.8KG ColorKey offers a 2-year limited warranty. Please visit our website at to register your product. Please note: As we continue to work towards improving our products and your experience as a user, we recommend that you check our website periodically for updates to user manuals and specifications at or you may contact us directly at info@colorkeyled.com. 13