Instruction Manual AC-E75. Ultra-Slim PIEZO 2 x 6 Matrix 500-User Outdoor Secured Access Control Unit. AC-E75 Ultra-Slim Secure Keypad IM Page 1

Transcription

1 Instruction Manual AC-E75 Ultra-Slim PIEZO 2 x 6 Matrix 500-User Outdoor Secured Access Control Unit AC-E75 Ultra-Slim Secure Keypad IM Page 1

2

3 Contents Contents...3 Introduction...7 Equipment Provided...7 Additional Equipment Required...8 Technical Specifications...9 Electrical Characteristics...9 Environmental Characteristics...9 Mechanical Characteristics...9 Key Features...10 Installation...11 Mounting the AC-E75 Controller...11 Wiring the AC-E Wiring Diagram # Wiring Diagram # Wiring Diagram # AC-E75 Ultra-Slim Secure Keypad IM Page 3

4 Normal, Secure, & Master Users s of Operation Changing the s of Operation Auxiliary Input Functions Alarms Case and Back Tamper Request to Exit (REX) Function PC-15T Power Supply Unit Programming the AC-E Entering Programming Exiting Programming Changing Lock Strike Code Changing Lock Strike Code Changing the Programming Code Changing the Normal / Secure Code Changing the Normal / Bypass Code and Chime settings Setting Fail Safe/Secure Operation Setting Tamper Siren Time Setting the Lock Strike Release Time AC-E75 Ultra-Slim Secure Keypad IM Page 4

5 Defining the Auxiliary Input...39 Enrolling Primary & Secondary Codes...42 Primary Codes...42 Secondary Codes...42 Enrolling Primary and Secondary Codes...43 Enrolling Primary and Secondary Codes using the Standard Method...43 Enrolling Secondary Codes using the Code Search Method...45 Deleting Primary & Secondary Codes...47 Deleting Primary and Secondary Codes using the Standard Method...47 Deleting Primary and Secondary Codes using the Code Search Method...48 Return to Factory Default Settings...50 Replacing a Lost Programming Code...51 Replacing a Lost Normal / Secure Code...52 PC-15T / PS-A15T/ PS-B15T / PS-E15T / PS- F15T POWER SUPPLY INSTALLATION INSTRUCTIONS...53 INTRODUCTION & KEY FEATURES...53 ELECTRICAL SPECIFICATIONS...54 ENVIRONMENTAL SPECIFICATIONS...55 MECHANICAL SPECIFICATIONS...55 WIRING RECOMMENDATIONS...56 PCB MOUNTING DIMENSIONS...56 AC-E75 Ultra-Slim Secure Keypad IM Page 5

6 PS-15T WITH ENCLOSURES PS-A15T / PS-E15T PS-B15T / PS-F15T Wiring Diagram Limited Lifetime Warranty WARRANTY WARRANTY DURATION WARRANTY COVERAGE EXCLUSIONS AND LIMITATIONS LIMITED LIFETIME WARRANTY TERMS PC15T Warranty Technical Support AC-E75 Ultra-Slim Secure Keypad IM Page 6

7 Introduction The AC-E75 is a vandal-resistant keypad access control unit suitable for external applications. The unit accepts up to 500 users and provides entry via the use of PIN codes. It is designed for high security applications, due to the fact that lock strike output and Request to Exit input are not located directly on the AC-E75, which eliminates the possibility of unauthorized entry to the restricted area. A specific Power Supply Unit, PC-15T, must be used in conjunction with the AC-E75. See page 53 for a detailed description of the PC-15T. Equipment Provided The following is provided as part of every AC-E75 package: AC-E75 Access Control Unit. Installation Kit Installation and Operating Instructions AC-E75 Ultra-Slim Secure Keypad IM Page 7

8 Additional Equipment Required Secured Power Supply PC-15T which connects to the following items: 1) Electric Lock Strike mechanism or a Magnetic Lock device, which implements Fail Safe (Power to Lock) or Fail Secure (Power to Open) functions. 2) Request to Exit (REX) button Normally open type. Switch is closed when pressed. Other Rosslare accessories can be found at Rosslare's Web Site: AC-E75 Ultra-Slim Secure Keypad IM Page 8

9 Technical Specifications Electrical Characteristics Operating Voltage Range: VDC Provided from Secure Power Supply (PC-15T) Maximum Input Current: Standby: Maximum: LEDs 15mA 40mA Two Tri-colored LEDs Communication C1, C2 Open collector 5V terminated Environmental Characteristics Operating Temperature: Operating Humidity: 0 F to 145 F (-18 C to 63 C) 0 to 95% (Non- Condensing) Suitable for outdoor use. (IP 65) Mechanical Characteristics Dimensions: Weight: 6.10"(155mm)L x 1.73"(44mm)W x 0.2"(5mm)D 0.33 lbs (150g) AC-E75 Ultra-Slim Secure Keypad IM Page 9

10 Key Features Here are some of the AC-E75 s key features: Bi-directional secure communication with Secure PC-15T Power Supply Ultra-Slim Flush-mount design on flat surface Built-in piezoelectric keypad for PIN code entry Internal Buzzer Two Status / Programming Interface LED's Three User Levels Normal User Secure User Master User Three s of Operation Normal Bypass Secure "Code Search" feature that helps make maintaining user codes easier Request-to-Exit (REX) signal from PC-15T Built-in Back Tamper Bell feature is available with PC-15T Programmable Lock Strike Release, Siren, and Alarm Delay timers Fully-potted construction for outdoor use AC-E75 Ultra-Slim Secure Keypad IM Page 10

11 Installation Mounting the AC-E75 Controller 1) Before starting, select the location to mount the AC-E75 controller. This location should be at shoulder height. 2) For wall mounting, use the included mounting template as a guide for drilling holes for mounting screws and wiring. For US Gang Box mounting, no hole drilling is necessary. CAUTION! DO NOT DRILL (This will damage the unit) A A 3) Mount the unit onto the Gang Box, feeding the cable though the hole and secure in the screws. It is preferred to use security screws, and a special tool. 4) Wire the controller according the wiring instructions on the following page. AC-E75 Ultra-Slim Secure Keypad IM Page 11

12 Wiring the AC-E75 The controller is supplied with a 17-cm pigtail, having a 6-conductor cable. To wire the Controller, perform the following steps: 1) Prepare the controller cable by cutting the cable jacket back 1¼ inch and strip the wire ½ inch. 2) Splice the controller pigtail wires to the corresponding devices and cover each connection. Refer to the wire color guide provided below and to the wiring diagrams provided following pages. Wire Color Guide RED Color BLACK / Shield WHITE GREEN PURPLE V INPUT Description GROUND C1 - Data C2 - Data Tamper Output BROWN Auxiliary Input 3) Trim and cover all conductors that are not used. AC-E75 Ultra-Slim Secure Keypad IM Page 12

13 Wiring Diagram #1 Wiring diagram and schematic for the AC-E75. AC Mains 16VAC 1.5A 25VA FROM A TRANSFORMER Not provided in PS-E15T and PS-F15T 12V LEADACID BATTERY ROSSLARE PC15-T SPEAKER OUT OUTPUT LED UP TO 7 AH RECOMMENDED +V C1 C2 N.C. N.O. REX. SECURED CONTROLLERLOCK 12VDC +V mA (Red) AC-E75 AC-S73 C1 C2 (Black) (White) (Green) Wiring Diagram #2 Wiring diagram for Monitor and Tamper input to external Alarm system. AC-E75 Ultra-Slim Secure Keypad IM Page 13

14 Wiring Diagram #3 Wiring diagram for Auxiliary signal input to external Alarm system. AC-E75 Ultra-Slim Secure Keypad IM Page 14

15 Normal, Secure, & Master Users The AC-E75 accepts up to 500 users and provides entry via the use of PIN codes. Each user is provided with two code memory slots, Memory Slot 1 (Primary Code) and Memory Slot 2 (Secondary Code). The way in which the two memory slots are programmed determines a user s access level and also determines the way in which the AC-E75 grants access in its three modes of operation. There are three user levels: Normal User A Normal User only has a Primary Code and is only granted access when the AC-E75 is in Normal or Bypass. Secure User A Secure User must have a Primary and Secondary Code programmed; the two codes must not be the same. The Secure User can gain access when the AC-E75 is in any of its three modes of operation. In Normal the Secure User must use their Primary Code to gain entry. In Secure the Secure User must present both their Primary and Secondary Codes in order to gain entry. AC-E75 Ultra-Slim Secure Keypad IM Page 15

16 Master User A Master User must have both Primary and Secondary Codes programmed with the same PIN code. The Master User can gain access during any mode of operation by presenting their PIN code once to the controller. (The Master User is convenient but is less secure than a Secure User.) AC-E75 Ultra-Slim Secure Keypad IM Page 16

17 s of Operation The AC-E75 has three modes of operation: 1) Normal MODE LED is GREEN green Normal is the default mode. In Normal mode the door is locked until a Primary Code is presented to the controller. Special codes such as Lock Strike Code 1 and Lock Strike Code 2 are active in Normal mode. (See pages for more information on the Lock Strike Codes). 2) Bypass MODE LED is ORANGE orange In Bypass, access to the premises is dependent on whether the controller's Lock Strike Relay is programmed for Fail Safe Operation or Fail Secure Operation. When the Lock Strike is programmed for Fail Secure Operation, the door is locked until the doorbell button is pressed. When the Lock Strike is programmed for Fail Safe Operation, the door is constantly unlocked. 3) Secure MODE LED is red RED AC-E75 Ultra-Slim Secure Keypad IM Page 17

18 Only Secure and Master Users can access the premises during the Secured. A Secure User must enter their Primary and Secondary Codes to gain entry. After entering their Primary Code the LED will flash green for 10 seconds, during which the Secondary Code must be entered. A Master User only needs to present their code once to gain entry. AC-E75 Ultra-Slim Secure Keypad IM Page 18

19 Changing the s of Operation Changing from Normal to Secure The default factory setting for the Normal / Secure code is ) Enter the 4-digit GREEN Normal / Secure code LED will flash RED red 2) Press the # key to confirm the mode change. LED is red RED Changing from Secure to Normal The default factory setting for the Normal / Secure code ) Enter the 4-digit RED Normal / Secure code. LED will flash GREEN green 2) Press the # key to confirm the mode change. LED will turn green GREEN AC-E75 Ultra-Slim Secure Keypad IM Page 19

20 Changing from Normal to Bypass See page 35 to create/modify the Normal / Bypass code. 1) Enter the 4 digit GREEN Normal / Bypass code. LED will flash orange ORANGE 2) Press the # key to confirm the mode change. LED will turn orange ORANGE Changing from Bypass to Normal See page 35 to create/modify the Normal / Bypass code. 1) Enter the 4 digit ORANGE Normal / Bypass code. LED will flash GREEN green 2) Press the # key to confirm the mode change. LED will turn green GREEN AC-E75 Ultra-Slim Secure Keypad IM Page 20

21 Auxiliary Input Functions The auxiliary input can be configured for use as one of the following functions: 1) Monitor Input providing a - Forced alarm 2) Monitor Input providing a Ajar alarm 3) Input for toggling between Normal and Secure Access modes 4) LED Control Input to control LED Alarms alarms can be generated by connecting the Auxiliary Input to a Position Switch. Either -Forced or -Ajar conditions are supported, as well as, a configurable delay timer for each alarm type. Only one -alarm is enabled at any one time. AC-E75 Ultra-Slim Secure Keypad IM Page 21

22 Case and Back Tamper If the case of the controller is opened or the controller is removed from the wall, a tamper event is triggered and a coded tamper signal is sent to the PC-15T Power Supply, or other compatible device, which will activate the siren. In addition, another output is opened, which can be connected to another device or alarm system, as necessary. Clearing a tamper event is done by entering a valid Employee or Lock Strike Code that will open the Lock Strike Output in the current mode of operation. For example, while in Secure mode, using the Lock Strike Codes to clear tamper event will not work because the Strike Codes does not work in Secure mode. However, applying a Master Code or Secure Code will clear the tamper event in Secure mode. AC-E75 Ultra-Slim Secure Keypad IM Page 22

23 Request to Exit (REX) Function The REX button is connected to the Power Supply Unit (PC-15T). The REX button must be located inside the premises to be secured and is used to open the door without the use of a PIN code. It is usually located in a convenient location, e.g. inside the door or at a receptionist's desk. The function of the REX button depends on whether the Lock Strike Relay is programmed for Fail Safe Operation or Fail Secure Operation. 1) Fail Secure Operation: From the moment the REX button is pressed, the door will be unlocked until the Lock Strike Release Time has passed. After this time, the door will be locked even if the REX button has not been released. Fail Safe Operation: From the moment the REX button is pressed, the door will be unlocked until the REX button is released, plus the Lock Strike Release Time. In this case the Lock Strike Relay only begins its count down once the REX button has been released. AC-E75 Ultra-Slim Secure Keypad IM Page 23

24 PC-15T Power Supply Unit The PC-15T is designed for use with Rosslare's secured series, stand alone access control units, including AC-E75. It is designed to operate indoors and installed within the premises to be secured. The AC-E75 must be used with PC-15T, which provides its Lock Strike output, Request to Exit (REX) Input and Speaker Functions: Bell and Siren*. Both units communicate through a proprietary Rosslare protocol, which provides a secure link between the controller and the power supply unit. This in turn activates the door unlocking. The PC-15T also functions as the power supply for the AC-E75. * The unit signal from the keypad used for Bell is also used for the door-opened chime. AC-E75 Ultra-Slim Secure Keypad IM Page 24

25 Programming the AC-E75 Programming the AC-E75 is done solely via the unit's keypad driven Programming Menu System. To reach the Programming Menu System the AC-E75 must first be placed into Programming mode. See Entering Programming on page 27 for more information. During the AC-E75's manufacturing process certain codes and settings are preprogrammed. These settings are the called the Default Factory Settings. The table below shows the names of all the AC-E75 Menus. It also shows of all the AC- E75 s default factory codes and settings. AC-E75 Ultra-Slim Secure Keypad IM Page 25

26 Programming Menu Menu Menu Description Number 1 Changing Lock Strike Code 1 2 Changing Lock Strike Code 2 3 Changing Program Code 4 Changing Normal/Secure Code 5 Changing Normal/Bypass Code 6 Changing Release Time Defining Auxiliary Input 7 Enrolling PIN Code 8 Deleting PIN Code 0 Return to Default Factory Setting Factory Settings N/A You will find a complete description and instructions for each of the above menu items on the following pages. AC-E75 Ultra-Slim Secure Keypad IM Page 26

27 Entering Programming 1) Press the # key two times within 2 seconds. LED will turn off LED will turn red 2) Enter your 4-digit Programming Code. If the Programming Code is valid the door LED will turn green and the AC- E75 will be in Programming RED GREEN NOTE: The AC-E75 must be in Normal to enter the Programming mode. The factory default Programming Code is If a Programming Code is not entered within 5 seconds, the AC-E75 will return to Normal mode. AC-E75 Ultra-Slim Secure Keypad IM Page 27

28 Exiting Programming 1) To exit the Programming mode at any time: Press the # key two times within 2 seconds (except for mode 7, where a double-press may be required.) You will hear 3 beeps. The LED will turn off and the LED will return to Normal. 2) Wrong entries may reset the controller back to Normal mode. 3) While in Programming mode if no key is pressed for 1 minute the AC-E75 will exit Programming mode and return to Normal mode. GREEN AC-E75 Ultra-Slim Secure Keypad IM Page 28

29 Changing Lock Strike Code 1 The Lock Strike Code 1 is mainly used as a method to quickly test the Lock Strike Relay during installation. When the first user is added to the controller, the default Lock Strike Code 1 will automatically be deleted. Once the code is programmed again, it will not be deleted with the entry of additional User Codes. 1) Enter Programming GREEN mode 2) Press 1 to enter Menu 1 The LED will turn red 3) Enter the new 4-digit code you wish to set as Lock Strike Code 1. 4) System returns to Normal mode You will hear three beeps RED???? GREEN GREEN NOTE: Lock Strike Code 1 does not function in Secure. AC-E75 Ultra-Slim Secure Keypad IM Page 29

30 Wrong entries will return the controller to Normal. Code 0000 will erase the Lock Strike Code 1. The Default Lock Strike code is AC-E75 Ultra-Slim Secure Keypad IM Page 30

31 Changing Lock Strike Code 2 The Lock Strike Code 2 is mainly used as a method to quickly test the Lock Strike Relay during installation. When the first user is added to the controller, the default Lock Strike Code 2 will automatically be deleted. Once the code is programmed again, it will not be deleted with the entry of additional User Codes. 1) Enter Programming mode 2) Press 2 to enter Menu 2 The LED will turn orange 3) Enter the new 4-digit code you wish to set as Lock Strike Code 2. 4) System returns to Normal mode You will hear three beeps GREEN ORANGE GREEN???? GREEN NOTE: Lock Strike Code 2 does not work in Secure. AC-E75 Ultra-Slim Secure Keypad IM Page 31

32 Wrong entries will return the controller to Normal. Code 0000 will erase the Lock Strike Code 2. The Default Lock Strike code is AC-E75 Ultra-Slim Secure Keypad IM Page 32

33 Changing the Programming Code 5) Enter Programming mode 6) Press 3 to enter Menu 3 The LED will turn green 7) Enter the new 4-digit code you wish to set as Programming Code 8) System returns to Normal mode You will hear three beeps GREEN GREEN GREEN???? GREEN NOTE: Programming Code cannot be erased, i.e. the code 0000 is not valid and will not erase the Programming Code. Default programming code is AC-E75 Ultra-Slim Secure Keypad IM Page 33

34 Changing the Normal / Secure Code 1) Enter Programming mode 2) Press 4 to enter Menu 4 The LED will flash red 3) Enter the new 4-digit code you wish to set as Normal / Secure Code 4) System returns to Normal mode You will hear three beeps GREEN RED GREEN???? GREEN NOTE: Code 0000 will erase the Normal / Secure Code. This code is disabled in case the Auxiliary Input is set to toggle between Normal and Secure access modes. Default Normal/Secure code is AC-E75 Ultra-Slim Secure Keypad IM Page 34

35 Changing the Normal / Bypass Code and Chime settings 1) Enter Programming mode 2) Press 5 to enter Menu 5 The LED will flash orange GREEN ORANGE GREEN 3) Below is a list of the four different ways that the Normal / Bypass Code and Chime can be programmed. a) Disable Bypass - Disable Chime b) Disable Bypass - Enable Chime c) Enable Bypass - Disable Chime d) Enable Bypass - Enable Chime a) Disable Bypass Code - Disable Chime Enter the 4-digit code b) Disable Bypass Code - Enable Chime Enter the 4-digit code c) Enable Bypass Code - Disable Chime Enter any 4-digit code??? 0 ending with 0 AC-E75 Ultra-Slim Secure Keypad IM Page 35

36 d) Enable Bypass Code - Enable Chime Enter any 4-digit code??? 0 not ending with 0 4) System returns to Normal You will hear three beeps The LED will turn off The LED will turn green NOTE: GREEN Code 0000 will erase the Normal / Bypass Code. Default Normal/Bypass code none. The chime is only generated when the Lock Strike Relay is activated due to a valid code entry. AC-E75 Ultra-Slim Secure Keypad IM Page 36

37 Setting Fail Safe/Secure Operation Setting Tamper Siren Time Setting the Lock Strike Release Time 1) Enter Programming mode Do GREEN 2) Press 6 to enter Menu 6 The LED will flash green 3) Construct the 4-digit code using the instructions below: First Digit For Fail Secure Operation the first digit should be 0 For Fail Safe Operation the first digit should be 1 Second Digit Siren Time in minutes (1-9, 0-disabled) Third and Fourth Digit Enter the number of seconds (from 1 to 99) that you want the Lock Strike to be released. Do GREEN GREEN???? AC-E75 Ultra-Slim Secure Keypad IM Page 37

38 For example, 0312 means Fail Secure Operation, a 2-minute Siren, and a 12- second Lock Strike release time. 4) System returns to Normal mode You will hear three beeps NOTE: GREEN Default value is 0004 which corresponds to Fail Secure operation, no siren, and 4- seconds Lock Strike release time. AC-E75 Ultra-Slim Secure Keypad IM Page 38

39 Defining the Auxiliary Input The default auxiliary setting is ) Enter Programming mode 2) Press 6 to enter Menu 6 The LED will flash green 3) Construct the 4-digit using the instructions below: Auxiliary Auxiliary Setting GREEN GREEN GREEN???? Auxiliary In addition to the Lock Strike Relay and Lock Strike REX, the AC-E75 features an Auxiliary Output Relay and an Auxiliary Input. The Auxiliary defines the function of the Auxiliary Input and Output. The Auxiliary also determines if the Auxiliary Output Relay is set for Fail Safe or Fail Secure Operation. AC-E75 Ultra-Slim Secure Keypad IM Page 39

40 Auxiliary Settings Each of the Auxiliary s has a two digit setting that affects how the Auxiliary functions. 4) System returns to Normal GREEN You will hear three beeps The LED will turn off. The LED will turn green The Second digit defines Auxiliary Input function while the Third and Fourth digits may have no meaning or otherwise they define delay times for door monitor functions. Digit 1 Digit 2 Digit 3+4 Auxiliary Input menu Auxiliary Input Function 2 3 Toggle Normal/Secure 2 6 Monitor + Forced Alarm N/A Delay* AC-E75 Ultra-Slim Secure Keypad IM Page 40

41 Digit 1 Digit 2 Digit Monitor + Ajar Alarm 2 8 LED Control RED 2 9 LED Control Green * Alarm Delay 0-99 seconds Delay* N/A N/A AC-E75 Ultra-Slim Secure Keypad IM Page 41

42 Enrolling Primary & Secondary Codes Primary Codes Primary Codes can only be enrolled to an empty User Slot, i.e. a slot where there is no existing Primary Code. Primary Codes must be unique, i.e. one user s Primary Code may not be the same as other users Primary Code. Primary Codes cannot be the same as any system codes, such as the Normal / Secure Code or Lock Strike Code. Users who hold a Primary Code can gain entry only during Normal mode. Secondary Codes Secondary Codes can only be enrolled to User Slot that already has a Primary Code enrolled but no Secondary Code. Secondary Codes do not have to be unique, i.e. multiple users can all hold the same Secondary Code. Secondary Codes cannot be the same as any system codes, such as the Normal / Secure Code or Lock Strike Codes. Users who hold Secondary Codes can gain entry in any of Operation. AC-E75 Ultra-Slim Secure Keypad IM Page 42

43 Enrolling Primary and Secondary Codes There are two methods to enroll Primary and Secondary codes, the Standard Method and the Code Search Method. a. The Standard Method is mainly used when the User Slot number for the user you wish to program is known. You can program both Primary and Secondary Codes using the Standard method. (See Enrolling Primary and Secondary Codes using the Standard Method - page 43.) b. The Code Search Method is mainly used when enrolling a user s Secondary Code and the User Slot Code is unknown. The Code Search method only works if a user s Primary Code is already enrolled but the Secondary Code is not. (See Enrolling Secondary Codes using the Code Search Method - page 45.) Enrolling Primary and Secondary Codes using the Standard Method 1) Enter Programming 2) Press 7 to enter Menu 7 The LED will turn orange GREEN ORANGE AC-E75 Ultra-Slim Secure Keypad IM Page 43

44 3) Enter the 3-digit User Slot number between 001 to 500 that you wish to enroll a Primary or Secondary code to. For example, the User Slot 003 represents User #3. 4) If the selected slot has no Primary Code, the LED will flash green, indicating that the controller is ready to accept a Primary Code. If the selected slot already has a Primary Code but no Secondary Code, the LED will flash red, indicating that the controller is ready to accept a??? GREEN ORANGE ORANGE AC-E75 Ultra-Slim Secure Keypad IM Page 44 RED Secondary Code. If the selected slot already has a Primary and Secondary Code, you will hear a long beep and the controller will return to Normal.

45 5) Enter the 4-digit PIN that you want to assign as the Primary or Secondary Code for this slot number. If the PIN that is entered is valid the LED will stop flashing and then the controller is ready for you to enter the next 3-digit slot number (refer to step 3) that you want to assign a code to, or press the # key to move to the next slot number (refer to step 4). If you do not wish to continue enrolling codes, press the # key twice and the controller will return to Normal mode. Enrolling Secondary Codes using the Code Search Method The Code Search feature enables you to quickly enroll a Secondary Code to a user who already has a Primary Code. 1) Enter GREEN Programming 2) Press 7 to ORANGE enter Menu 7 The LED will turn orange 3) Enter the 3-digit User Slot number 000 The LED will flash orange ORANGE AC-E75 Ultra-Slim Secure Keypad IM Page 45

46 The controller is now waiting for the Primary Code of the User you want to add a Secondary Code to. 4) Enter the 4-digit PIN Code of the Primary Code belonging to the user you want to add a Secondary Code to. The LED will flash red RED If the Primary Code entered is not valid, you will hear a long beep and the AC-E75 will continue to wait for a valid Primary Code. 5) Enter the 4-digit PIN Code to be used as the Secondary Code. If the Secondary Code is valid the controller will beep three times and return to Normal. If the Secondary Code is invalid the controller will sound a long beep and the AC-E75 will continue to wait for a valid Secondary Code to be entered. ORANGE AC-E75 Ultra-Slim Secure Keypad IM Page 46

47 Deleting Primary & Secondary Codes There are two methods to delete Primary and Secondary codes: the Standard Method and the Code Search Method. When deleting a User Slot, both the Primary Code and the Secondary code are erased. Deleting Primary and Secondary Codes using the Standard Method 1) Enter Programming GREEN 2) Press 8 to enter RED Menu 8 The LED will turn red 3) Enter the 3-digit User Slot codes you wish to delete. The LED will flash red Indicating the controller is waiting for the Programming Code to confirm the deletion.??? ORANGE RED ORANGE AC-E75 Ultra-Slim Secure Keypad IM Page 47

48 If the User Slot is empty you will hear a long beep and the AC-E75 will return to Normal. 4) Enter your Programming Code to confirm the deletion.???? If the Programming Code is valid, you will hear three beeps and the AC-E75 will return to Normal. If the Programming Code is invalid, you will hear a long beep and the AC- E75 will return to Normal. NOTE: It is recommended that a record be kept of added and deleted users so that it will be easier to keep track of which user slots are empty and which user slots are not. Deleting Primary and Secondary Codes using the Code Search Method 1) Enter Programming GREEN 2) Press 8 to enter RED Menu 8 The LED will turn red ORANGE AC-E75 Ultra-Slim Secure Keypad IM Page 48

49 3) Enter the 3-digit User Slot number 000 The LED will flash orange ORANGE AC-E75 Ultra-Slim Secure Keypad IM Page 49 RED The controller is now waiting for the Primary Code of the user you want to delete. 4) Enter the 4-digit PIN???? Code of the Primary Code belonging to the user you want to delete. The LED will flash red RED ORANGE 5) Enter your Programming Code to confirm the deletion. If the Programming Code is valid, you will hear three beeps and the AC-E75 will return to Normal. If the Programming Code is invalid, you will hear a long beep and the AC-E75 will return to Normal. NOTE: It is recommended that a record be kept of added and deleted users so that it will be easier to keep track of which user slots are empty and which user slots are not.

50 Return to Factory Default Settings WARNING: You must be very careful before using this command! Doing so will erase the entire memory which includes all User and Special Codes, and return all codes to their factory default settings. 1) Enter Programming GREEN 2) Press 0 to enter Menu 0 RED RED The LED will flash red The LED will flash red 3) Enter your 4-digit Programming Code.???? If the Programming Code is valid, all memory will be erased. You will hear three beeps and the controller will return to Normal. If the Programming Code is invalid you will hear a long beep and the controller will return to Normal without erasing the memory of the controller. AC-E75 Ultra-Slim Secure Keypad IM Page 50

51 Replacing a Lost Programming Code NOTE: The AC-E75 must be in Normal mode otherwise this will not work. Make sure that the LED is green before proceeding. 1) Remove power from the Power Supply Unit (PC-15T). 2) Press the REX button on the Power Supply Unit (PC-15T). 3) Apply power to the unit with REX button pressed. 4) Release the REX button. 5) You now have 15 seconds to program a new Programming code into the Access Control unit using the initial default code 1234, before the controller reverts to the existing code. AC-E75 Ultra-Slim Secure Keypad IM Page 51

52 Replacing a Lost Normal / Secure Code NOTE: The AC-E75 must be in Secure otherwise this will not work. Make sure that the LED is red before proceeding. 1) Remove power from the Power Supply Unit (PC-15T). 2) Press the REX Button on the Power Supply Unit (PC-15T). 3) Apply power to the unit with the REX button pressed. 4) Release the REX Button. 5) You now have 15 seconds to program a new Normal / Secure code into the Access Control unit using the initial default code 3838, before the controller reverts to the existing code. AC-E75 Ultra-Slim Secure Keypad IM Page 52

53 PC-15T / PS-A15T/ PS-B15T / PS-E15T / PS-F15T POWER SUPPLY INSTALLATION INSTRUCTIONS INTRODUCTION & KEY FEATURES The PC-15T Power Supply is designed for use with all Rosslare secured series standalone access control units. The PC-15T contains two power supplies. One power supply is for the lock strike, the other is for the access control unit (ACU). The lock strike is attached directly to the power supply. This design isolates the lock from the ACU securing the functionality of lock even if the ACU is tampered with. When a valid code is entered at the ACU, the ACU communicates to the power supply using a Rosslare proprietary protocol sending a command to activate the lock. Similarly, the Release to Exit (REX) button is attached directly to the power supply, when the REX is pushed the power supply will communicate the REX request to the ACU and then the ACU will communicate back to the power supply to activate the lock strike. If the data line between the ACU and the power supply is cut, the system will immediately detect that the data line has AC-E75 Ultra-Slim Secure Keypad IM Page 53

54 been tampered with, and will generate a siren for one minute. A sealed lead acid battery charger is built-in to provide back-up power for the ACU and the Lock Strike. The PC-15T can also power an external speaker that is controlled by the ACU to annunciate Belland Siren tones. The PC-15T is also available in two steel enclosures. For more details on the models with enclosures, PS-A15T, PS-B15T, PS- E15T, and PS-F15 see page 57. ELECTRICAL SPECIFICATIONS AC Input: 16 ~ 18 VAC (1.5 A, 25 VA) DC Battery Charger: 12V DC Lead Acid Battery Up to 7AH recommended DC Input wired to backup battery terminals: VDC Battery current draw depends on attached devices Lock Strike Output and Power Supply: 5 A Relay SPDT connection available via terminal blocks 12 VDC, constant voltage AC-E75 Ultra-Slim Secure Keypad IM Page 54

55 1.2 A current limit Controller Power Supply: 12 VDC, constant voltage 300 ma current limit Communications: Rosslare proprietary protocol Power LED & Speaker Output: Power LED indicator. 8 OHM, 0.25 W (Minimum) For bell, chime and siren alerts ENVIRONMENTAL SPECIFICATIONS Operating Temperature: -10 C to 70 C (14 F to 158 F) Operating Humidity: 0 to 95% (Non-Condensing) MECHANICAL SPECIFICATIONS Weight: 59 grams (0.11 lbs) Dimensions: 77mm (3.0 ) Length 57mm (2.2 ) Width 33mm (1.3 ) Depth AC-E75 Ultra-Slim Secure Keypad IM Page 55

56 WIRING RECOMMENDATIONS Maximum distance between the Controller and the PC-15T is 50m (150ft). Lock wiring should be 20 Gage Communication wiring (C1 & C2) should be twisted Pair, 22 Gage, shielded or unshielded. PCB MOUNTING DIMENSIONS Dimensions for PCB mounting holes are provided below. 46mm (1.8 ) 66mm (2.6 ) AC-E75 Ultra-Slim Secure Keypad IM Page 56

57 PS-15T WITH ENCLOSURES PS-A15T / PS-E15T The PS-A15T and PS-E15T enclosures include a built-in speaker and enough room for a CE or UL approved transformer. PS-A15T The PS-A15T comes with a built-in CE approved transformer. That is Class II Rated (Double insulated) and contains thermal fuse protection. Max: 125 C, 1A. See transformer specifications below: Input: Output: Certifications: Compliance: 230 VAC ~ 50Hz, 0.14 A 16 VAC ~ 1.5A, 25 VA CE A1:1998 EN :1997 EN :1997 AC-E75 Ultra-Slim Secure Keypad IM Page 57

58 PS-E15T The PS-E15T is shipped without a transformer and is designed to be powered from an external transformer. When sold in the United States a UL approved transformer is recommended. The enclosure weight and dimensions are provided below: Dimensions: 182mm (7.2 ) Length 80mm (3.1 ) Width 68mm (2.7 ) Depth Weight: 1.24Kg (2.7lbs) PS-A15T 0.63Kg (1.3lbs) PS-E15T PS-B15T / PS-F15T The PS-B15T and PS-F15T enclosures include a built-in speaker and enough room for a CE or UL approved transformer as well as a lead acid backup battery (up-to 7 AH). AC-E75 Ultra-Slim Secure Keypad IM Page 58

59 PS-B15T The PS-B15T comes with a built-in CE approved transformer. That is Class II Rated (double insulated) and contains thermal fuse protection. Max: 125 C, 1A. See transformer specifications below: Input: Output: Certifications: Compliance: 230 VAC ~ 50Hz, 0.14 A 16 VAC ~ 1.5A, 25 VA CE A1:1998 EN :1997 EN :1997 PS-F15T The PS-F15T is shipped without a transformer and is designed to be powered from an external transformer. When sold in the United States a UL approved transformer is recommended. The enclosure weight and dimensions are provided below: Dimensions: 205mm (8.1 ) Length 200mm (7.9 ) Width 82mm (3.2 ) Depth Weight: 1.24Kg (2.7lbs) PS-B15T 0.63Kg (1.3lbs) PS-F15T AC-E75 Ultra-Slim Secure Keypad IM Page 59

60 Wiring Diagram Wiring Diagram and schematic for the PC- 15T, PS-A15T, PS-B15T, PS-E15T, PS- F15T are provided below: 16V AC (1.5A, 25VA) AC Mains FROM A TRANSFORMER Not provided in PS-E15T and PS-F15T 12V LEAD ACID BATTERY VIN +BAT 16VAC 12VDC ROSSLARE PC-15T SPEAKER OUT OUTPUT LED UP TO 7 AH RECOMMENDED +V C1 C2 N.C. N.O. REX. SECURED CONTROLLER LOCK 12VDC OP-PSA12-V4 N.C. N.O. +V (12 300mA) COMPATIBLE ROSSLARE CONTROLLER C1 C2 AC-E75 Ultra-Slim Secure Keypad IM Page 60

61 Limited Lifetime Warranty ROSSLARE ENTERPRISES LIMITED S (Rosslare) LIMITED LIFETIME WARRANTY is applicable worldwide. This warranty supersedes any other warranty. Rosslare's LIMITED LIFETIME WARRANTY is subject to the following conditions: WARRANTY Warranty of Rosslare's products extends to the original purchaser of the Rosslare product and is not transferable. WARRANTY DURATION Rosslare warrants this product against defects in material and/or workmanship for the life of the product from the date of original purchase to the original purchaser. WARRANTY COVERAGE Rosslare will repair or replace, at its option, any product that under normal conditions of use and service proves to be defective in material or workmanship. No charge will be made for labor or parts with respect to defects covered by this warranty, provided that Rosslare does the work or a Rosslare authorized service center. This warranty does not cover expenses incurred in the transportation, removal or reinstallation of the product, whether or not proven defective. Replacement or repairs furnished under this warranty are subject to the same terms and conditions of the original warranty. AC-E75 Ultra-Slim Secure Keypad IM Page 61

62 EXCLUSIONS AND LIMITATIONS Specifically excluded from this warranty are failures caused by abuse, neglect, misuse, improper operation, normal wear, accident, improper maintenance or modification. This warranty does not cover repair or replacement where normal use has exhausted the life of a part or instrument. Service life of the product is dependent upon the care it receives and the conditions under which it has to operate. In no event shall Rosslare be liable for incidental or consequential damages. LIMITED LIFETIME WARRANTY TERMS The terms of this warranty may not be varied by any person, whether or not purporting to represent or act on behalf of Rosslare. This warranty represents the full extent of Rosslare's responsibility. Repair, replacement, or refund of the original purchase price, of the product is the exclusive remedy. This limited lifetime warranty is provided in lieu of all other warranties. All other warranties expressed or implied, including without limitation, implied warranties of merchantability and fitness for a particular purpose, are specifically excluded. In no event shall Rosslare be liable for damages in excess of the purchase price of the product, or for any other incidental, consequential or special damages, including but not limited to loss of use, loss of time, commercial loss, inconvenience, and loss of profits, arising from the installation, use, or inability to use such product, to the fullest extent that any such loss or damage may be disclaimed by law. This warranty shall become null and void in AC-E75 Ultra-Slim Secure Keypad IM Page 62

63 the event of a violation of the provisions of this limited warranty. PC15T Warranty The Manufacturer's warranty on this product is for a period of two years from the date of manufacture against defects in materials and workmanship. Manufacturer's warranty hereunder is limited to repair or replacement, at the manufacturer's sole option, if the product is found to be defective in normal use during the warranty period. The warranty is given in favor of the original purchase only. Subject to the above warranty, manufacturer's liability and that of it's distributors, re-sellers and agents and is wholly limited to the original purchase price and no payment will be made for related or consequential loss including but not limited to labor costs incurred in inspection, replacement or repair of defective products. This warranty is given expressly and in place of all other expressed or implied warranties of merchantability and fitness for a particular purpose and this warranty is the only warranty made by the manufacturer. No agent, representatives or employee of the manufacturer has the authority to waive, alter or add to the printed provisions of this warranty, to make representation of warranty not contained herein or to extend this warranty to anyone other than the original purchaser of the product. The PC-15T, PS-A15T, PS-B15T, PS-E15T, and PS- F15T are guaranteed against defects in workmanship and material for a period of 24 (Twenty Four) months from date of purchase. Return the faulty product with a dated proof of purchase to your dealer for replacement. AC-E75 Ultra-Slim Secure Keypad IM Page 63

64 Technical Support International Web Site: Asia, Australia, & Middle East: Rosslare Enterprises Ltd Wing Fat Industrial Bldg., 12 Wang Tai Road, Kowloon Bay, Hong Kong Tel: (852) Fax: (852) Europe & Russia Rosslare Israel, Ltd. HaMelecha 22, Rosh HaAyin, 48091, Israel Tel: (972) Fax: (972) support@rosslaresecurity.com United States and Canada: Rosslare NAPDC 200 East Howard Street, Suite 238, Des Plaines, IL USA Tel: (847) Fax: (847) support@rosslaresecurity.com AC-E75 Ultra-Slim Secure Keypad IM Page 64

65 South America: Rosslare Latin America Pringles 878, 1640 Martinez, Buenos Aires, Argentina Tel: (54) Fax: (54) / 9J-RSP-069 AC-E75 Ultra-Slim Secure Keypad IM Page 65