ECE 333: Introduction to Communication Networks Fall 2002

Transcription

1 ECE 333: Introduction to Communication Networks Fall 2002 Lecture 26: Transport layer I 1 Transport Layer In the remaining lectures, we will discuss several issues that are commonly addressed at the transport layer in a network. We will consider several general transport layer issues, and, as a specific example, we will use the transport layer in the. The has two primary transport layer protocols and UDP both of these will be discussed. In the architecture, the transport layer sits between the application layer and the network layer. For this reason, it is the most visible layer to application designers. The service of the transport layer is to provide a virtual end-to-end message-pipe for applications. In other words, two applications on different hosts can communicate messages to each other as if they are directly connected the details of the underlying network are hidden. 2

2 Transport Layer The transport layer is an end-to-end layer this means that nodes within the subnet do not participate in transport layer protocols only the end hosts. As with other layers, transport layer protocols send data as a sequence of packets. In /IP these packets are called segments. 1 Application Application Transport Transport 1 Actually only packets are called segments and UDP packets are referred to as datagrams but we will use segments to refer to either of these. 3 Transport layer issues Two main issues addressed at the transport layer are Multiplexing Improving the service offered by network layer 4

3 Multiplexing The network layer provides communication between two hosts. The transport layer provides communication between two processes running on different hosts. A process is an instance of a program that is running on a host. There may be multiple processes communicating between two hosts for example, there could be a FTP session and a Telnet session between the same two hosts. The transport layer provides a way to multiplex/demultiplex communication between various processes. To provide multiplexing, the transport layer adds an address to each segment indicating the source and destination processes. Note these addresses need only be unique locally on a given host. In /IP these transport layer addresses are called port-numbers. In other protocols, different names are used transport layer addresses; for example, in ATM networks these are called AAL-SAP s (ATM Adaptation Layer Service Access Points). In the port numbers are 16-bits long. The port numbers between 0 and 1023 are reserved and called well-known ports. These numbers are assigned to well-known applications such as FTP, Telnet, and HTTP. For example HTTP is assigned well-known port number Multiplexing Most network applications are based on a client-server architecture where one process, the client, requests services from a second process, the server. For example, a web browser implements the client side of HTTP and a web server implements the server side. The client initiates communication and the server responds. A client sending a request to a web server would use the destination port 80, and in IP would indicate the transport layer protocol is (this is the transport layer protocol used by HTTP). The sending port number is picked from some other port numbers that are not being used for another session by the client. In this way if several different HTTP sessions are established between the two hosts, the sending port number distinguishes them. Thus, the 4-tuple: (sending port, sending IP address, destination port, destination IP address) uniquely identifies a process-to-process connection in the. The use of well-known ports is just one way for finding the destination address. Another example is to use a special process called a process or directory server, which responds to requests for services with the correct port number. 6

4 Improving the Network layer service When the underlying network layer does not offer adequate service for an application, it is the job of the transport layer to improve this service. For example, suppose the network layer does not guarantee that every packet will arrive. Then the transport layer could provide a way to recover from lost packets and ensure that each packet is delivered correctly. As with the other layers, the service provided by the transport layer can have different characteristics. For example, it may be reliable or unreliable, connection-oriented or connectionless, etc. It could also try to guarantee a certain Quality of Service (QoS), i.e. a given data rate or delay. The service provided by the underlying network layer will determine: 1. How much work has to be performed at the transport layer to provide a certain service. 2. What types of service can even be provided. For example, consider designing a transport layer to offer a service that guarantees the delay of a message. If the underlying network layer already offers this, than little work would be needed at the transport layer. However, if the network layer did not provide any delay guarantees, then it may be impossible to provide this service at the transport layer. 7 Transport layer services in the The network layer in the provides an unreliable, connectionless datagram service. IP tries to deliver each datagram to the destination, but makes no guarantees, that the data will arrive correctly, in order or even at all. This is sometimes described as a best effort service. In the there are two transport layer protocols, each offering a different service. UDP (User Datagram Protocol) provides an unreliable, connectionless transport layer protocol. The second transport layer protocol, (Transport Control Protocol), provides a reliable, connectionoriented transport service. Some common applications and the corresponding transport layer protocol used are shown below: Application protocol SMTP( ) DNS HTTP (web browsing) Telephony FTP Telnet Typical transport protocol UDP UDP 8

5 UDP The packet format for UDP is shown below. Basically all UDP provides is a multiplexing capability on top of IP. The length field gives the length of the entire packet including the header. The checksum is calculated on the entire packet (and also on part of the IP header). Calculating the checksum is optional, and if an error is detected the packet may be discarded or may be passed on to the application with an error flag. 16 bits 16 bits Source port Destination port UDP length UDP checksum Data 9 converts the unreliable, best effort service of IP into a reliable service, i.e., it ensures that each segment is delivered correctly, only once, and in order. Converting an unreliable connection into a reliable connection is basically the same problem we have considered at the data link layer, and essentially the same solution is used. That is numbers each segment and uses an ARQ protocol to recover lost segments. Some versions of implement Go Back N and other versions implement Selective Repeat. However, there are a few important differences between the transport layer and the data link layer. At the data link layer, we viewed an ARQ protocol as being operated between two nodes connected by a point-to-point link. At the transport layer, this protocol is implemented between two hosts connected over network. In the later case, packets can arrive out-of-order, and packets may also be stored in buffers within the network and then arrive at much later times. Also the round-trip time will change with different connections and connection establishment is more complicated. 10