The router with ADSL 2+ and UMTS (3.5G/HSPA+) bintec RS230au+

Transcription

1 The router with ADSL 2+ and UMTS (3.5G/HSPA+) UMTS (3.5G, HSPA+, 21.1/5.76 Mbps) modem ADSL 2+ modem - ADSL over POTS 5 x Gigabit Ethernet Web-based configuration / wizards IPSec - 5 tunnels, HW acceleration Prepared for IPv6 Stateful Inspection Firewall

2 The router with ADSL 2+ and UMTS (3.5G/HSPA+) The with integrated ADSL 2+ Annex A and HSPA+ UMTS modem (21.1/5.76 Mbps) is, thanks to its high-speed UMTS capability, especially suited for scenarios where high availability and redundancy are indispensable. The is a powerful and, thanks to its comprehensive equipment, flexible router. The integrated UMTS modem supports the HSPA+ (3.5G) standard with a maximum download rate of 21.1 Mbit/s and a maximum upload rate of 5.76 Mbit/s. In addition, the device has an integrated ADSL 2+ modem which supports Annex A (ADSL over POTS) in accordance with ITU G The router in the fan-free metal housing guarantees long-term reliability in critical corporate applications and is ideal for use as an access router in SMEs, branch offices and home offices. In addition to the integrated ADSL 2+ modem, the device has five Gigabit Ethernet ports, which can be configured for LAN, WAN or DMZ, and comes with a licence for five hardware-accelerated IPSec tunnels. Thanks to the variety of different connection technologies used, the RS230au+ sets new standards for the flexibility of access routers. By using an external indoor or outdoor UMTS antenna it is possible to significantly improve reception. Using functions flexibly Only a few functions are required to forward data packets between two networks. The bintec RS230au+ has features that go far beyond just routing and allow it to be integrated into complex IT infrastructures. By using Extended Routing and NAT (ERN) the data can be routed in IP routing according to criteria such as IP protocols (Layer 4), source or destination IP address, source or destination port, TOS/DSCP, source or destination interface and the status of the destination interface. In addition, you can also use network address translation to translate the data traffic for both inbound and outbound connections and individually for each interface based on a wide range of criteria. The comprehensive multicast support makes the device ideal for use in multimedia and streaming applications. The Stateful Inspection Firewall (SIF) offers effective protection against attacks from the Internet through dynamic packet filtering. Firewall handling is made easier through numerous pre-configured services. An optional content filter rounds off the security functions of the devices*. In this case, all the outgoing Internet enquiries are classified and allow contents not wanted to be reliably filtered out. The basic equipment of the RS Series also offers a SIP application level gateway (ALG) for the direct connection of IP telephones in the network or for registering with a VoIP provider, without affecting the security of the WAN connection. The corresponding releases in NAT and the internal Stateful Inspection Firewall are controlled automatically by ALG for the length of the communication. Quality of Service is more than a watchword in FEC devices. Thanks to the rising convergence between voice and data, the classification of data streams is gaining in importance. Our routers provide corresponding QoS mechanisms for prioritising the VoIP traffic ahead of normal internet traffic, for example, and to guarantee it sufficient bandwidth. Alternatively you can give normal data traffic priority over traffic. The bintec QoS implementation allows voice data to be Page 2 / 10

3 processed before e-mal data, for example, within a VPN tunnel. The DNS proxy function supports the LAN for address implementation and the automated IP configuration of PCs is carried out over an integrated DHCP server. Comprehensive IPSec implementation The IPSec implementation integrated in works not only with preshared keys but also with certificates. This allows a public key infrastructure to be created for maximum security. (The German Federal Office for Information Security also recommends the use of certificates.) Furthermore, the bintec IPSec implementation offers support when creating VPN connections with dynamic IP addresses: Even small branch offices can be reached without having to be permanently online. If both VPN nodes only have dynamic IP addresses, confidential information can continue. The exchange of IP addresses is carried out over a dynamic DNS provider. Load Balancing/Backup The devices offer a unique level of flexibility thanks to the wide variety of interfaces supported. The supports the ability to configure two interfaces as WAN interfaces. As a result, there is not only more bandwidth available, but there is the opportunity to spread data traffic across individual WAN connections according to load or data type. Equally, you can use a connection (e.g. UMTS) for the VPN connection to the head office and use a second WAN port for a low-cost ADSL connection to guarantee the company's other data traffic. If either connection fails, the other can take over the entire data transfer. Simple configuration and maintenance The router is configured over the Funkwerk Configuration Interface (FCI), using the integrated configuration wizards for example. The FCI is a web-based graphic user surface that you can use from any PC with an up-to-date Web browser via an HTTP or encrypted HTTPS connection. It also offers the opportunity to manage the devices locally and remotely over other configuration accesses such as Telnet, SSH and GSM dialin. DIME Manager from Funkwerk Enterprise Communications (FEC) is a free tool for managing FEC devices. Dime Manager is aimed at administrators who manage networks with up to 50 devices. The software simplifies the management and configuration of routers or access points either individually or in logical groups. When developing DIME Manager, simple and efficient operation was the primary aim. It allows, for example, software updates or configurations to be applied to individual devices or groups of devices simply by drag and drop. DIME Manager recognises and manages new devices in the network using SNMP multicasts, in other words independent of their current IP address. * Content filtering is a fee-paying service and is available as a 30-day trial version. Variants - UK ( ) IP Access Router; incl. ADSL modem (Annex A, POTS); UMTS (3,5G/USPA+) Modem; incl. IPSec (5 tunnels), certificates, HW encryption; 4+1 Gigabit Eth. switch; USB port; not for use with Deutsche Telekom equipment; UK version. Page 3 / 10

4 ( ) IP Access Router; incl. ADSL modem (Annex A, POTS); UMTS (3,5G/USPA+) Modem; incl. IPSec (5 tunnels), certificates, HW encryption; 4+1 Gigabit Eth. switch; USB port; not for use with Deutsche Telekom equipment; german and intern. version. Features DSL ADSL ADSL over POTS (ITU G Annex A G.Lite (ITU G.922.2) ADSL 2 / ADSL 2+ ADSL over POTS (ITU G.992.3, ITU G Annex A) ADSL 2 ADSL 2 ADSL ADSL2 over POTS Annex L ADSL2 over POTS Annex M Support of Dying Gasp ATM Support of layer 1 protocol AAL5, PVCs, RFC 1483 ATM ATM ATM Support of up to 7 virtual channels (VC) Support of OAM F4/F5 line monitoring Support of ATM traffic management (COS - CBR, VBR, UBR) GSM / UMTS Supported standards UMTS (3.5G) / WCDMS bands Support of UMTS (3.5G/HSPA+), (download rate up to 21.1 Mbps, upload rate up to to 5.76), GPRS, Edge and GSM 850/900/1900/2100 MHz VPN PPTP (PAC/PNS) GRE v.0 L2TP Number of VPN tunnels IPSec Number of IPSec tunnels IPSec Algorithms IPSec hardware acceleration IPSec IKE IPSec IKE Config Mode Point to Point Tunneling Protocol for establishing fo Virtual Privat Networks, inclusive strong encryption methods with 128 Bit (MPPE) up to 168 Bit (DES/3DES, Blowfish) Generic Routing Encapsulation V.0 according RFC 2784 for common encapsulation Layer 2 tunnelling protocol inclusive PPP user authentication Inclusive 5 active VPN tunnels with the protocols IPSec, PPTP, L2TP and GRE v.0 (also in combination possible) Internet Protocol Security establishing of VPN connections Inclusive 5 active IPSec tunnels DES (64 Bit), 3DES (192 Bit), AES (128,192,256 Bit), CAST (128 Bit), Blowfish ( Bit), Twofish (256 Bit); MD-5, SHA-1, RipeMD160, Tiger192 Hashes Integrated hardware acceleration for IPSec encryption algorithms DES, 3DES, AES IPSec key exchange via preshared keys or certificates IKE Config Mode server enables dynamic assignment of IP addresses from the address pool of the company. IKE Config Mode client enables the router, to get assigned dynamically an IP address. Page 4 / 10

5 VPN IPSec IKE XAUTH (Client/Server) IPSec IKE XAUTH (Client/Server) IPSec NAT-T IPSec IPComp IPSec certificates (PKI) IPSec SCEP IPSec Certificate Revocation Lists (CRL) IPSec Dead Peer Detection (DPD) IPSec dynamic DNS IPSec RADIUS IPSec Multi User IPSec QoS IPSec NAT IPSec throughput (1400) IPSec throughput (256) Internet Key Exchange protocol Extended Authenticaion client for login to XAUTH server and XAUTH server for loging of XAUTH clients Inclusive the forwarding to a RADIUS-OTP (One Time Password) server (supported OTP solutions see Support of NAT-Traversal (Nat-T) for the application at VPN lines with NAT IPSec IPComp data compression for higher data throughput via LZS Support of X.509 multi-level certificates compatible to Micrososft and Open SSL CA server; upload of PKCS#7/8/10/12 files via TFTP, HTTP, HTTP, LDAP, file upload and manual via FCI Certificates management via SCEP (Simple Certificate Enrollment Protocol) Support of remote CRLs on a server via LDAP or local CRLs Continuous control of IPSec connection Enables the registering of dynamic IP addresses by a dynamic DNS provider for establishing a IPSec connection. Authentication of IPSec connections at a RADIUS server. Additionally the IPSec peers, which were configured on a RADIUS server, can be loaded into the gateway (RADIUS dialout). Enables the Dial-in of several IPSec clients via a single IPSec peer configuration entry The possibility to operate Quality of Service (traffic shaping) inside of an IPSec tunnel By activating of NAT on an IPSec connection it is possible, to implement several remote locations with identical local IP addess networks in different IP nets for the VPN connection 34 Mbps with 1400 Byte packets with AES 256 / AES 128 / 3 DES encryption 11 Mbps with 256 Byte packets with AES 256 / AES 128 / 3 DES encryption Security NAT/PAT Policy based NAT/PAT Policy based NAT/PAT Content Filtering Stateful Inspection Firewall Packet Filter Symmetric Network and Port Address Translation (NAT/PAT) with randomly generated ports inclusive Multi NAT (1:1 translation of whole networks) Network and Port Address Translation via different criteria like IP protocols, source/destination IP Address, source/destination port For incoming and outgoing connections and for each interface variable configurable Optional ISS/Cobion Content filter (30 day test license inclusive) Packet filtering depending on the direction with controling and interpretation of each single connection status Filtering of IP packets according to different criteria like IP protocols, source/destination IP address, source/destination port, TOS/DSCP, layer 2 priority for each interface variable configurable Routing Page 5 / 10

6 Routing Policy based Routing Multicast IGMP Multicast IGMP Proxy Multicast inside IPSec tunnel RIP Extended RIP Routing throughput (1518) Routing throughput (256) Extended routing (Policy Based Routing) depending of diffent criteria like IP protocols (Layer4), source/destination IP address, source/destination port, TOS/DSCP, source/destination interface and destination interface status Support of Internet Group Management Protocol (IGMP v1, v2, v3) for the simultaneous distribution of IP packets to several stations For easy forwarding of multicast packets via dedicated interfaces Enables the transmission of multicast packets via an IPSec tunnel Support of RIPv1 and RIPv2, separated configurable for each interface Triggerd RIP updates according RFC 2091 and 2453, Poisened Rerverse for a better distribution of the routes; furthermore the possibility to define RIP filters for each interface. 199 Mbps with 1518 Byte packets 198 Mbps with 256 Byte packets Protocols / Encapsulations PPP/MLPPP PPPoE (Server/Client) MLPPPoE (Server/Client) PPPoA IPoA DNS DYN DNS DNS Forwarding DHCP Packet size controling Support of Point to Point Protocol (PPP) for establishing of standard PPP connections, inclusive the Multilink extension MLPPP for the bundeling of several connections Point-to-Point Protocol over Ethernet (Client and Server) for establisching of PPP connections via Ethernet/DSL (RFC 2516) Multilink extension MLPPPoE for bundeling several PPPoE connections (only if both sides support MLPPPoE) Point to Point Protocol over ATM for establishing of PPP connections via ATM/DSL Enables the easy routing of IP via ATM DNS client, DNS server, DNS relay and DNS proxy Enables the registering of dynamic assigned IP addresses at adynamic DNS provider, e.g. for establishing of VPN connections Enables the forwarding of DNS requests of free configurable domains to assigned DNS server. DHCP Client, Server, Proxy and Relay for siplified TCP/IP configuration Adaption of PMTU or automatic packet size controling via fragmentation QoS Policy based Traffic Shapping Bandwidth reservation DiffServ Layer2/3 tagging TCP Download Rate Control Dynamic bandwidth management via IP traffic shaping Dynamic reservation of bandwidth, allocation of guaranteed and maximum bandwidths Priority Queuing of packets on the basis of the DiffServ/TOS field Conversion of 802.1p layer 2 priorisation information to layer 3 diffserv attributes For reservation of bandwidth for VoIP connections Page 6 / 10

7 Redundancy / Loadbalancing BRRP BoD Load Balancing VPN backup Optional: Bintec Router Redundancy Protocol for backup of several passive or active devices with free selectable priority Bandwidth on Demand: dynamic bandwidth to suit data traffic load Static and dynamic load balancing to several WAN connections on IP layer Simple VPN backup via different media. Additional enables the Funkwerk interface based VPN concept the application of routing protocols for VPN connections. Layer 2 Functionality Bridging VLAN Proxy ARP Support of layer 2 bridging with the possibility of separation of network segment via the configuration of bridge groups Support of up to 32 VLAN (Virtual LAN) for segmentation of the network in independent virtual segments (workgroups) Enables the router to answer ARP requests for hosts, which are accessible via the router. That enables the remote clients to use an IP address from the local net. Logging / Monitoring / Reporting Internal system logging External system logging alert SNMP traps Activity Monitor IPSec monitoring Interfaces monitoring IP accounting RADIUS accounting Keep Alive Monitoring Tracing Tracing Syslog storage in RAM, display via web-based configuration user interface (http/https), filter for subsystem, level, message Syslog, several syslog server with different syslog level configurable Automatic alert by definable events SNMP traps (v1, v2, v3) configurable Sending of information to a PC on which Brickware is installed Display of IPSec tunnel and IPSec statistic; output via web-based configuration user interface (http/https) Statistic information of all pysical and logical interfaces (ETH0, ETH1, SSIDx,...), output via web-based configuration user interface (http/https) Detailed IP accounting, source, destination, port, interface and packet/bytes counter, transmission also via syslog protocol to syslog server RADIUS accounting for PPP, PPTP, PPPoE and ISDN dialup connections Control of hosts/connections via ICMP polling Detailed traces can be done for different protocols e.g. ISDN, PPPoE,... generation local on the device and remote via DIME manager Traces can be stored in PCAP format, so that import to different open source trace tools (e.g. wireshark) is possible. Administration / Management Page 7 / 10

8 Administration / Management RADIUS RADIUS dialout TACACS+ Time synchronization Automatic Time Settings Supported management systems Configurable scheduler Funkwerk Configuration Interface (FCI) Software update Remote maintenance Configuration via serial interface GSM remote maintenance Device discovery function On The Fly configuration SNMP SNMP configuration Configuration export and import SSH login HP OpenView XAdmin Central check of access authorization at one or several RADIUS server, RADIUS (PPP, IPSec inclusive X-Auth and login authentication) On a RADIUS server configured PPP und IPSec connection can be loaded into the gateway (RADIUS dialout). Support of TACACS+ server for login authentication and for shell comando authorization The device system time can be obtained via ISDN and from a SNTP server (up to 3 time server configurable). The obtained time can also be transmitted per SNTP to SNTP clients. Time zone profiles are configurable. That enables an automatic change from summer to winter time. DIME Manager, XAdmin Configuring of time and event controlled tasks, e.g. reboot device, activate/deactivate interface, activate/deactivate WLAN, trigger SW update and configuration backup Integrated web server for web-based configuration via HTTP or HTTPS (supporting self created certificates). This user interface is by most of Funkwerk EC products identical. Software updates are free of charge; update via local files, HTTP, TFTP or via direct access to the FEC web server Remote maintenance via telnet, SSL, SSH, HTTP, HTTPS and SNMP (V1,V2,V3) Serial configuariton interface is available Remote maintenance via GSM login (external USB UMTS (3G) modem required) Device discovery via SNMP multicast. No reboot after reconfiguration required SNMP (v1, v2, v3), USM model, VACM views, SNMP traps (v1, v2, v3) configurable, SNMP IP access list configurable Complete management with MIB-II, MIB , Enterprise MIB Load and save configurations, optional encrypted; optional automatic control via scheduler Supports SSH V1.5 and SSH V2.0 for secure connections of terminal applications Integration into Network Node Manager Support of XAdmin roll out and configuration management tool for larger router installations (IP) Interfaces Ethernet USB 2.0 host Serial console ADSL/ADSL 2+ 5 x 10/100/1000 Mbps Ethernet Twisted Pair, autosensing, Auto MDI/MDI-X, up to 4 ports can be switches as additional WAN ports incl. load balancing, all Ethernet ports can be configured as LAN or WAN. USB 2.0 full speed host port for connecting UMTS (3G) USB modem sticks (supported sticks: see Serial console interface / COM port (mini USB) ADSL over POTS Page 8 / 10

9 Interfaces GSM/UMTS (3.5G) External UMTS antenna connectors UMTS (3G), HSPA+ (3.5G), GPRS, Edge or GSM with intergrated GSM/UMTS (3.5G) modem Two SMA antenna connectors for external UMTS antennas Hardware Realtime clock Wall mounting System time persists even at power failure for some hours. Integrated in housing Environment Temperature range: Operational 0 C to 40 C; storage -10 C to 70 C; Max. rel. humidity 10-95% (non condensing) Power supply Power consumption Housing External wall power supply V / 12 V DC, 1.5 A, with energy efficient switching controler; complies with EuP directive 2008/28/EC Less than 5 Watt Metal case, opening for Kensington lock, connectors at back side, prepared for wall mounting Dimension Ca. 235 mm x 31.5 mm x 146,5 mm (W x H x D) Weight Fan Reset button Status LEDs Standards and certifications Ca. 1100g Fanless design therefor high MTBF Restart or reset to factory state possible Power, Status, 10 * Ethernet, ADSL, ISDN, WLAN, USB R&TTE Directive 1999/5/EG; EN 55022; EN EN 55024/A1; EN ; EN ; EN ; EN ; EN ; EN ; EN ; EN ; EN ; EN Content of Delivery Manual DVD Ethernet cable Power supply ADSL cable UMTS (3G) antenna Quick Installation Guide in German and English DVD with system software, management software and documentation 1 Ethernet cable, 3m Wall power supply V / 12 V DC, 1.5 A, with high efficient switching controler ADSL cable (RJ11-RJ11), 3m Two external 2 dbi dipol quadband antennas Service Warranty Software Update 2 year manufacturer warranty inclusive advanced replacement Free-of-charge software updates for system software (BOSS) and management software (DIME manager) Options Page 9 / 10

10 Software Licenses RS-Series-BRRP ( ) Cobion Content Filter Small (80551) RS-Series software license for Bintec Router Redundancy Protocol (BRRP) Cobion content filter for RSxxx, Rxx02, RTxx02 series; R230a(w), R232b(w), TR200, R1200(w/wu), R3000(w), R3400, R3800, R232aw; list price for one year Pick-up Service / Warranty Extension Service Package 'medium' ( ) Warranty extension of 3 years to a total of 5 years, including advanced replacement for FEC products of the category 'medium'. Please find a detailed description as well as an overview of the categories on Product Services HotSpotHosting 1yr 1 location ( ) Hot Spot solution hosting fee for 1 year and 1 location Additional HotSpot location ( ) Additional location for Hot Spot solution ( ) HotSpotHosting 2yr 1 location ( ) Hot Spot solution hosting fee for 2 year and 1 location Add-ons PS-UK-RSxxx ( ) PS-EURO-RSxxx ( ) Active Antenna UMTS-USB-sticks ( ) Home Compenser ( ) ANT-Omni-3G-UMTS ( ) Power supply UK for RSxxx Power supply EURO for RSxxx Funkwerk active UMTS (3G) antenna for UMTS (3G) USB Sticks, UMTS band 1 active antenna, 7db, 15m cable Funkwerk Home Compenser ; GSM/GPRS/EDGE/UMTS/HSCSD/HSDPA/HSUPA send and receive signal booster, inclusive antenna and 7m cable, SMA connector for RS120wu, RS230au+, RS232bu+ Omni-directional multi-band GSM-3G (UMTS) antenna incl. mounting kit and 5 m cable for outdoor usage, SMA connector for RS120wu, RS230au+, RS232bu+ Cables Console Cable MiniUSB to DSUB9 ( ) Serial console cable for RS, RT, Rxx02 Series and hybird (Mini USB to D-SUB 9) Page 10 / 10