TTL TO ETHERNET Module. MODEL No: TTL-Sereth1P VER 1.0

Transcription

1 TTL TO ETHERNET Module MODEL No: TTL-Sereth1P VER 1.0 MILLENNIUM TECHNOLOGIES 440, MASTER MIND 1, ROYAL PALMS ESTATE AAREY MILK COLONY, GOREGAON (EAST), MUMBAI INDIA. PH: , TTL TO ETH_1P.doc, Ver1.0 1 of 1

2 Table of Contents 1.0 INTRODUCTION PRODUCT DESCRIPTION FEATURES SPECIFICATIONS CONNECTION DETAILS SOFTWARE INSTALLATION DEVICE CONFIGURATION CONFIGURATION PARAMETERS...11 TTL TO ETH_1P.doc, Ver1.0 2 of 2

3 1.0 INTRODUCTION PRODUCT DESCRIPTION This module is a Serial (TTL)-to-Ethernet converter module. This module is very useful for connecting a legacy serial device to an Ethernet network. It supports virtual mode of operation. In virtual mode, one can configure the board as a PC COM port, which enables to run legacy application software based on standard PC COM port. We also provide various Data Acquisition Cards with serial interfaces such as Digital I/O Cards, Relay Driver Cards, and Analog I/O Cards etc FEATURES 10/100Mbps Ethernet port TTL logic levels 3.3 V and 5 V Asynchronous Serial Ports RJ-45 Socket for Ethernet Device Configuration utility Automatic detection of device 5 Volts operation SPECIFICATIONS Baud Rate Supported 1200,2400,4800,9600,19200,38400,57600, Core Module Memory 64KB Flash, 4KB RAM Ethernet 10/100Mbps Dimension 60x30x25 mm Power Consumption 300mA@5V, 2Watt max. TTL TO ETH_1P.doc, Ver1.0 3 of 3

4 1.0.4 CONNECTION DETAILS TOP View of Module PIN NUMBER DESCRIPTION 1 NC 2 NC 3 NC 4 NC 5 NC 6 NC 7 TX-EN0 8 NC 9 RX0 10 TX0 11,12 5V (I/P) 13 NC 14 NC 15,16 3.3V (O/P) 18,20 GND 19 NC TTL TO ETH_1P.doc, Ver1.0 4 of 4

5 2.0 SOFTWARE INSTALLATION Unpacking the product you will find Software installation CD. Please browse Single Port Setup Utility folder and run Setup.exe, which will install the necessary software and files in to your computer. The installation steps are as follows: Setup will initialize installation Then you will next screen as shown below. Click Next to continue to the next window. TTL TO ETH_1P.doc, Ver1.0 5 of 5

6 The software will install to default directory i.e. C:\Program Files\Millennium Technologies\MT_1P_SERETH_CONFIG. If you want to change location please browse the desired folder. TTL TO ETH_1P.doc, Ver1.0 6 of 6

7 Please click on Next button The installation process will begin. You can see progress on the screen. After finishing the process you will se following screen. Click on Finish button. TTL TO ETH_1P.doc, Ver1.0 7 of 7

8 3.0 DEVICE CONFIGURATION NOTE: - Please disable windows firewall, while detecting and configuring device. The user will have to configure the device using the configuration Utility. This utility is provided to search, install and configure the device in a network. All settings like baud rate, IP address, subnetmask, gateway etc. can be set using this utility. These settings are stored in permanent flash memory of the converter. To run the utility, click on desktop icon or browse installation folder and run MT_1P_SERETH_CONFIG.exe.. First you will see welcome screen. Then you will see following screen Please click on Search Broadcast Search menu. The utility will start searching device(s). TTL TO ETH_1P.doc, Ver1.0 8 of 8

9 You can see detected devices in table. After search is finished you can see all the devices found in the table. Please double click on the device you want to configure. The configure screen will appear. Please set various parameters displayed on screen. The description of each parameter is given in next section. To apply changes click on Apply button. The device selection screen will appear again. Please search the device again and verify all changes are applied correctly. TTL TO ETH_1P.doc, Ver1.0 9 of 9

10 If converter and computer are in two different networks, you can configure device using Search by IP method. Please click on Search Search By IP menu. You will be asked IP of converter as shown below. Please enter IP address of converter and click on OK. The remaining steps to search and configure converter are similar. TTL TO ETH_1P.doc, Ver of 10

11 4.0 CONFIGURATION PARAMETERS Network Settings: 1. Host IPADDRESS: This IP address is the IP address of the PC where the configuration utility is installed. 2. DIN: Device Identification No.(No need for users). Default: 2 3. IP ADDRESS: Put the IP address for the device u want to set. Default SUBNET: put subnet mask for the device according to your network settings. Default: GATEWAY: put Gateway for the device according to your network settings. Gateway is required only when the device is in other network Default: Serial Settings: 1. BAUD RATE: Baud rate for the serial device. You can configure from 1200 to Default: Parity: Parity you can select from NO Parity, Even Parity, and Odd parity according to the serial device supports. Default: No Parity 3. Interface: Interface can be RS-232, RS-485 and RS-422. Default: RS Socket Alive Time: If there is no any activity on Ethernet for the amount of time (in mins) specified in parameter, then device closes its socket after time is over. Default : 0 mins.(socket is never closed) TTL TO ETH_1P.doc, Ver of 11