LAB5: OSPF IPv4. OSPF: Stub. Disclaimer
|
|
|
- Alaina Hubbard
- 5 years ago
- Views:
Transcription
1 Page1 LAB5: SPF IPv4 Disclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material is as complete and accurate as possible, the enclosed material is presented on an as is basis. Neither the authors nor Forum assume any liability or responsibility to any person or entity with respect to loss or damages incurred from the information contained in this guide. This Lab Guide was developed by RSTForum. Any similarities between material presented in this configuration guide and any other material is completely coincidental. SPF: Stub
2 Page2 LAB 5: Diagram Note: This Lab was developed on isco IS Version15.2(4) M1 ADVENTERPRISEK9-M.
3 Page3 LAB 5: SPF Stub: Task 1: onfigure SPF Stub Step 1 In the configuration mode of router configure loopbacks with network address in sequence & redistribute these connected network in SPF process: R1: interface loopback 100 ip address interface loopback 101 ip address interface loopback 102 ip address interface loopback 103 ip address R1: redistribute connected subnet metric-type 1 R2#show ip route! (Show router s routing table and IPv4 entries) odes: L - local, - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, - SPF, IA - SPF inter area N1 - SPF NSSA external type 1, N2 - SPF NSSA external type 2 E1 - SPF external type 1, E2 - SPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - DR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override Gateway of last resort is not set L L /32 is subnetted, 3 subnets [110/65] via , 00:56:32, Serial2/ [110/65] via , 00:56:32, Serial2/ [110/65] via , 00:56:32, Serial2/ /8 is variably subnetted, 2 subnets, 2 masks /24 is directly connected, Serial2/ /32 is directly connected, Serial2/ /8 is variably subnetted, 6 subnets, 2 masks /24 is directly connected, Loopback /32 is directly connected, Loopback /24 is directly connected, Loopback2
4 Page4 L /32 is directly connected, Loopback /24 is directly connected, Loopback3 L /32 is directly connected, Loopback /8 is variably subnetted, 2 subnets, 2 masks /24 is directly connected, Ethernet0/0 L /32 is directly connected, Ethernet0/ /32 is subnetted, 3 subnets [110/11] via , 00:55:48, Ethernet0/ [110/11] via , 00:55:48, Ethernet0/ [110/11] via , 00:55:48, Ethernet0/ /24 is subnetted, 1 subnets IA [110/74] via , 00:55:48, Ethernet0/ /32 is subnetted, 3 subnets IA [110/75] via , 00:55:10, Ethernet0/0 IA [110/75] via , 00:55:10, Ethernet0/0 IA [110/75] via , 00:55:10, Ethernet0/ /24 is subnetted, 4 subnets E [110/84] via , 00:00:39, Serial2/0 E [110/84] via , 00:00:39, Serial2/0 E [110/84] via , 00:00:39, Serial2/0 E [110/84] via , 00:00:39, Serial2/0 Step 2 onfigure SPF Stub R3: area 2 stub R4: area 2 stub Task 2: Verification: Step 1 Verify routes on neighbor router routing table R4#show ip route! (Show router s routing table and IPv4 entries) odes: L - local, - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, - SPF, IA - SPF inter area N1 - SPF NSSA external type 1, N2 - SPF NSSA external type 2 E1 - SPF external type 1, E2 - SPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - DR, P - periodic downloaded static route, H - NHRP, l - LISP
5 Page5 + - replicated route, % - next hop override Gateway of last resort is to network *IA /0 [110/65] via , 00:00:46, Serial2/ /32 is subnetted, 3 subnets IA [110/139] via , 00:00:46, Serial2/0 IA [110/139] via , 00:00:46, Serial2/0 IA [110/139] via , 00:00:46, Serial2/ /24 is subnetted, 1 subnets IA [110/138] via , 00:00:46, Serial2/ /32 is subnetted, 3 subnets IA [110/75] via , 00:00:46, Serial2/0 IA [110/75] via , 00:00:46, Serial2/0 IA [110/75] via , 00:00:46, Serial2/ /24 is subnetted, 1 subnets IA [110/74] via , 00:00:46, Serial2/ /32 is subnetted, 3 subnets IA [110/65] via , 00:00:46, Serial2/0 IA [110/65] via , 00:00:46, Serial2/0 IA [110/65] via , 00:00:46, Serial2/ /8 is variably subnetted, 2 subnets, 2 masks /24 is directly connected, Serial2/0 L /32 is directly connected, Serial2/ /8 is variably subnetted, 6 subnets, 2 masks /24 is directly connected, Loopback1 L /32 is directly connected, Loopback /24 is directly connected, Loopback2 L /32 is directly connected, Loopback /24 is directly connected, Loopback3 L /32 is directly connected, Loopback3 (Stub area is area in which external routes LSA 5 does not propagate, instead it automatically creates default route towards ABR.) R4#ping Type escape sequence to abort. Sending 5, 100-byte IMP Echos to , timeout is 2 seconds:!!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 8/8/9 ms
LAB11: EIGRP IPv4. EIGRP: Stub. Disclaimer
Page1 AB11: EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB8: OSPF IPv4. OSPF: Virtual Link. Disclaimer
Page1 AB8: OSPF IPv4 Disclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB8: Named EIGRP IPv4
Page1 AB8: Named EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB15: EIGRP IPv4. LAB 15: Diagram. Disclaimer
AB15: EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material is as
LAB1: BGP IPv4. BGP: Initial Config. Disclaimer
Page1 LAB1: BGP IPv4 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB16: Named EIGRP IPv4
AB16: Named EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB12: OSPF IPv6. OSPF: Redistribution. Disclaimer
Page1 LAB12: OSPF IPv6 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
Layer3 VPN with RIP protocol between CE-PE
MPLS Layer3 VPN with IP protocol between E-PE Disclaimer This onfiguration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made to
LAB20: EIGRP IPv6. EIGRP: Summarization. Disclaimer
Page1 LAB20: EIGRP IPv6 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB1: EIGRP IPv4. EIGRP: Initial Config. Disclaimer
Page1 AB1: EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
Layer3 VPN with OSPF Protocol between CE-PE
MPLS Layer3 VPN with OSPF Protocol between CE-PE Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made
LAB2: Named EIGRP IPv4
Page1 AB2: Named EIGRP IPv4 isclaimer This onfiguration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
LAB24: EIGRP IPv6. EIGRP: Load Balancing. Disclaimer
Page1 LAB24: EIGRP IPv6 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
Failover with EIGRP Using VRF Configuration Example
Failover with EIGRP Using VRF onfiguration Example ocument I: 113446 ontents Introduction Prerequisites Hardware and Software Versions onventions onfigure Network iagram onfigurations Verify Show ommands
MPLS Troubleshooting. Contents. Prerequisites. Document ID: Requirements. Components Used
MPLS Troubleshooting Document ID: 12492 ontents Introduction Prerequisites Requirements omponents Used onventions Troubleshoot Procedures Verify That Routing Protocol Runs Verify EF Switching Verify MPLS
Chapter 7 Lab 7-2, Using the AS_PATH Attribute
Chapter 7 Topology Objectives Use BGP commands to prevent private AS numbers from being advertised to the outside world. Use the AS_PATH attribute to filter BGP routes based on their source AS numbers.
Page1. Cisco IOS Software, Linux Software (I86BI_LINUX-ADVENTERPRISEK9-M), Version 15.2(4)M1, DEVELOPMENT TEST SOFTWARE
BGP Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made to ensure that all material is as complete
Implement Static Routes for IPv6 Configuration Example
Implement Static Routes for IPv6 Configuration Example Document ID: 113361 Contents Introduction Prerequisites Components Used Conventions Configure Network Diagram Configurations Verify Related Information
DMVPN Topology. Page1
DMVPN DMVPN Topology Page1 LAB 2: Configure EIGRP over DMVPN: Task 1: Configure EIGRP over DMVPN Process Step 1 In the configuration mode of router configure EIGRP over DMVPN by following command: R1:
Easy Virtual Network Configuration Example
Easy Virtual Network Configuration Example Document ID: 117974 Contributed by Fabrice Ducomble, Cisco TAC Engineer. Aug 04, 2014 Contents Introduction Prerequisites Requirements Components Used Background
Lab- Configuring Basic Single-Area OSPFv2
Lab- onfiguring Basic Single-Area OSPFv2 Topology G0/0 G0/0 2013 isco and/or its affiliates. All rights reserved. This document is isco Public. Page 1 of 29 Addressing Table Objectives Device Interface
Chapter 4 Lab 4-1, Redistribution Between EIGRP and OSPF. Topology. Objectives. CCNPv7 ROUTE
hapter 4 Topology Objectives Review EIGRP and OSPF configuration. Summarize routes in EIGRP. Summarize in OSPF at an ABR. Redistribute into EIGRP. Redistribute into OSPF. Summarize in OSPF at an ASBR.
Adapted from the Synchronization example in g/case/studies/icsbgp4.html
Adapted from the Synchronization example in http://www.cisco.com/en/us/docs/internetworkin g/case/studies/icsbgp4.html When an AS provides transit service to other ASs when there are non-bgp routers in
Configuration and Management of Networks
Configuring BGP using the AS_PATH attribute Topology Objectives Background Use BGP commands to prevent private AS numbers from being advertised to the outside world. Use the AS_PATH attribute to filter
LAB14: Named EIGRP IPv4
Page1 LAB14: Named EIGRP IPv4 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all
RR> RR> RR>en RR# RR# RR# RR# *Oct 2 04:57:03.684: %AMDP2_FE-6-EXCESSCOLL: Ethernet0/2 TDR=0, TRC=0 RR#
RR> RR> RR>en *Oct 2 04:57:03.684: %AMDP2_FE-6-EXCESSCOLL: Ethernet0/2 TDR=0, TRC=0 term len 0 show run Building configuration... Current configuration : 2568 bytes version 15.4 service timestamps debug
LAB16: BGP IPv6. BGP: Route Reflector. Disclaimer
Page1 LAB16: BGP IPv6 Disclaimer This Configuration Guide is designed to assist members to enhance their skills in respective technology area. While every effort has been made to ensure that all material
RealCiscoLAB.com. Chapter 6 Lab 6-2, Using the AS_PATH Attribute. Topology. Objectives. Background. CCNPv6 ROUTE
RealCiscoLAB.com CCNPv6 ROUTE Chapter 6 Lab 6-2, Using the AS_PATH Attribute Topology Objectives Background Use BGP commands to prevent private AS numbers from being advertised to the outside world. Use
Adjust Administrative Distance for Route Selection in Cisco IOS Routers Configuration Example
Adjust Administrative Distance for Route Selection in Cisco IOS Routers Configuration Example Document ID: 113153 Contents Introduction Prerequisites Requirements Components Used Conventions Configure
Network Layer Week 5. Module : Computer Networks Lecturer: Lucy White Office : 324
Network Layer Week 5 Module : Computer Networks Lecturer: Lucy White lbwhite@wit.ie Office : 324 1 Network Layer Network Layer Protocols Common Network Layer Protocols Internet Protocol version 4 (IPv4)
Chapter 7 Lab 7-1, Configuring BGP with Default Routing
Chapter 7 Topology Objectives Configure BGP to exchange routing information with two ISPs. Background The International Travel Agency (ITA) relies extensively on the Internet for sales. For this reason,
Contents. Introduction. Prerequisites. Requirements
Contents Introduction Prerequisites Requirements Components Used Configure Network Diagram Configurations Verify Inheritence with EIGRP Named mode Route Replication with EIGRP name mode Routing Context
Chapter 3 Lab 3-3, OSPF Virtual Links and Area Summarization
NPv6 RUTE hapter 3 Lab 3-3, SPF Virtual Links and Area Summarization Topology bjectives Background onfigure multi-area SPF on a r. Verify multi-area behavior. reate an SPF virtual link. Summarize an area.
GRE Tunnel with VRF Configuration Example
GRE Tunnel with VRF Configuration Example Document ID: 46252 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot Caveats
Distance vector Routing protocols. 2000, Cisco Systems, Inc. 9-1
Distance vector Routing protocols 2000, Cisco Systems, Inc. 9-1 IP Routing Configuration Tasks Router configuration Select routing protocols Specify networks or interfaces RIP Network 172.16.0.0 IGRP,
Configuration and Management of Networks
onfiguration and Management of Networks SPF Virtual Links and Area Summarization The lab is built on the topology: bjectives Background! onfigure multi-area SPF on a r.! Verify multi-area behavior.! reate
Chapter 3 Lab 3-2, Multi-Area OSPFv2 and OSPFv3 with Stub Area
Chapter 3 Topology Objectives Configure multi-area OSPFv2 for IPv4. Configure multi-area OSPFv3 for IPv6 Verify multi-area behavior. Configure stub and totally stubby areas for OSPFv2. Configure stub and
Chapter 1 Lab 1-1, Basic RIPng and Default Gateway Configuration
Chapter 1 Lab 1-1, Basic RIPng and Default Gateway Configuration Topology Objectives Configure IPv6 addressing. Configure and verify RIPng on R1 and R2. Configure IPv6 static routes between R2 and R3.
IP NAT Troubleshooting. Solutions. Luke Bibby, CCIE #45527
IP NAT Troubleshooting Solutions Luke Bibby, CCIE #45527 Quick Overview of Scenario Solutions Scenario #1 R2 s E0/0 should be NAT inside not NAT outside ACL 100 is configured incorrectly NAT policy missing
Lab 3.2 Configuring a Basic GRE Tunnel
Lab 3.2 onfiguring a Basic GRE Tunnel Learning Objectives onfigure a GRE tunnel onfigure EIGRP on a router onfigure and test routing over the tunnel interfaces Topology iagram Scenario This lab is designed
Lab 2-3 Summarization and Default Network Advertisement
Lab 2-3 Summarization and efault Network Advertisement Learning Objectives Review basic EIGRP configuration onfigure and verify EIGRP auto-summarization onfigure and verify EIGRP manual summarization Learn
EIGRP Lab / lo1. .1 lo / /30
EIGRP Lab 172,16,1.0/24.1 lo1 192.168.20.0/30.2.1 Merida fa0 fa0 Vargas lo2.1 lo2.5.1 lo1 192.168.30.0/24 172.16.2.0/24 192.168.20.4.0/30 Scenario: Loopback0 is used for RouterID Loopback1 is a virtual
Lab Configuring IPv4 Static and Default Routes (Solution)
(Solution) Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.0.1 255.255.255.0 N/A S0/0/1 10.1.1.1 255.255.255.252 N/A R3 G0/1 192.168.1.1 255.255.255.0
Chapter 4 Lab 4-1, Redistribution Between RIP and OSPF
hapter 4 Lab 4-1, Redistribution Between RIP and OSPF Topology Objectives Review configuration and verification of RIP and OSPF. onfigure passive interfaces in both RIP and OSPF. Filter routing updates
CCNA Exploration: Routing Protocols and Concepts Chapter 11 Case Study
bjectives: Consolidate SPF knowledge. Describe the operation of SPF multi-area. Introduce the concept of route summarization with SPF. Introduce the concept of SPF optimization. Intro: Trevni Inc. needed
Routing Information Protocol Version 2.0
Routing Information Protocol Version 2.0 RIPv2 Objective: onfigure RIPv2 between R1 and R2 to obtain connectivity between Networks Directions onfigure R1's interface F0/0 with the IP address 10.1.0.1/16
The information in this document is based on Cisco IOS Software Release 15.4 version.
Contents Introduction Prerequisites Requirements Components Used Background Information Configure Network Diagram Relevant Configuration Verify Test case 1 Test case 2 Test case 3 Troubleshoot Introduction
Chapter 8 Lab 8-3, Configuring 6to4 Tunnels
Chapter 8 Lab 8-3, Configuring 6to4 Tunnels Topology Objectives Configure EIGRP for IPv4. Create a 6to4 tunnel. Configure static IPv6 routes. Background In this lab, you configure EIGRP for full connectivity
LAB 5: DMVPN BGP. LAB 5: Diagram. Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M.
LAB 5: DMVPN BGP LAB 5: Diagram Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M. LAB 5: Configure BGP over DMVPN Configuration Step 1: Enable loopback and physical interfaces
Building the Routing Table. Introducing the Routing Table Directly Connected Networks Static Routing Dynamic Routing Routing Table Principles
Building the Routing Table Introducing the Routing Table Directly Connected Networks Static Routing Dynamic Routing Routing Table Principles Introducing the Routing Table R1# show ip route Codes: C - connected,
Chapter 3 Lab 3-1, Single-Area OSPF Link Costs and Interface Priorities
NPv6 ROUTE hapter 3 Lab 3-1, Single-Area OSPF Link osts and Interface Priorities Topology Objectives onfigure single-area OSPF on a router. Advertise loopback interfaces into OSPF. Verify OSPF adjacencies.
Lab - Troubleshooting Connectivity Issues
Lab - Troubleshooting Connectivity Issues Topology Addressing Table R1 ISP Objectives Device Interface IP Address Subnet Mask Default Gateway G0/1 192.168.1.1 255.255.255.0 N/A S0/0/0 10.1.1.1 255.255.255.252
INTERNET TEACHING LAB: Interior Gateway Protocol (IGP) LAB
INTERNET TEACHING LAB: Interior Gateway Protocol (IGP) LAB Overview In this lab, we will explore some common interior gateway protocols - RIP version 1 (Routing Information Protocol) - OSPF (Open Shortest
Initial Configurations for OSPF over a Point to Point Link
Initial onfigurations for OSPF over a Point to Point Link Document ID: 13687 ontents Introduction Prerequisites Requirements omponents Used onventions OSPF over a Point to Point Link with IP Addresses
CCNA Exploration: Routing Protocols and Concepts Chapter 8 Case Study
Objectives: Consolidate routing table reading skills. Introduce the idea of more than 1 routing protocol running into the same router. Explain the use of routes to Null0 interface. Intro: Connex Inc. is
Basic Router Configuration
This section includes information about some basic router configuration, and contains the following sections: Default Configuration, on page 1 Configuring Global Parameters, on page 2 Configuring Gigabit
RealCiscoLAB.com. Chapter 2 Lab 2-2, EIGRP Load Balancing. Topology. Objectives. Background. CCNPv6 ROUTE
RealCiscoLAB.com CCNPv6 ROUTE Chapter 2 Lab 2-2, EIGRP Load Balancing Topology Objectives Background Review a basic EIGRP configuration. Explore the EIGRP topology table. Identify successors, feasible
Lab - Configuring Basic Single-Area OSPFv2
Lab - Configuring Basic Single-Area SPFv2 Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway G0/0 192.168.1.1 255.255.255.0 N/A R1 S0/0/0 (DCE) 192.168.12.1 255.255.255.252
Configuration and Management of Networks
EIGRP Summarization and efault Network Advertisement The lab is built on the topology: Topology Objectives Review a basic EIGRP configuration. onfigure and verify EIGRP auto-summarization. onfigure and
Route Redistribution 2005 Cisco Systems, Inc. All rights reserved. 1of 38
1of 38 Basic Route Redistribution Presented by: Allan Johnson Cisco Academy Conference 2005 2of 38 Outline of Discussion Route Redistribution Overview Example 1: IGRP and EIGRP Automatic Redistribution
Lab- Troubleshooting Basic EIGRP for 1Pv4
Lab- Troubleshooting Basic EIGRP for 1Pv4 Topology G0/0 G0/0 PC-A PC-C 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 27 Addressing Table efault Gateway
Configuration and Management of Networks
onfiguration and Management of Networks Single Area SPF Link osts and Interface Priorities The lab is built on the topology: bjectives Background! onfigure single-area SPF on a r.! Advertise loopback interfaces
FlexVPN HA Dual Hub Configuration Example
FlexVPN HA Dual Hub Configuration Example Document ID: 118888 Contributed by Piotr Kupisiewicz, Wen Zhang, and Frederic Detienne, Cisco TAC Engineers. Apr 08, 2015 Contents Introduction Prerequisites Requirements
Lab 8a. OSPF. Set up OSPF in a single area so that all subnets are visible from all routers.
Rev. 08.09 Lab 8a. OSPF c cnac o okbook.com G O A L Set up OSPF in a single area so that all subnets are visible from all routers. Gi 0/0 Gi 0/0 Lo 0. 0..0.0 /0. 0..0. / Topology You'll need routers of
OSPF Commands. Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols IP2R-61
OSPF Commands Use the commands in this chapter to configure and monitor the Open Shortest Path First (OSPF) routing protocol. For OSPF configuration information and examples, refer to the Configuring OSPF
Chapter 6 Lab 6-3, Configuring IBGP and EBGP Sessions, Local Preference, and MED
Chapter 6 Lab 6-3, Configuring IBGP and EBGP Sessions, Local Preference, and MED Topology Objectives Background For IBGP peers to correctly exchange routing information, use the next-hop-self command with
CCNA Semester 2 labs. Part 2 of 2 Labs for chapters 8 11
CCNA Semester 2 labs Part 2 of 2 Labs for chapters 8 11 8.2.4.5 Lab - Configuring Basic Single-Area OSPFv2 8.3.3.6 Lab - Configuring Basic Single-Area OSPFv3 9.2.2.7 Lab - Configuring and Verifying Standard
Chapter 6: Network Layer
Chapter 6: Network Layer Introduction to Networks Intro to Networks v5 Network Layer Intro to Networks v5 2 The Network Layer End to End Transport processes Addressing end devices Encapsulation of Packets
OSPF Support for Multi-VRF on CE Routers
OSPF Support for Multi-VRF on CE Routers Finding Feature Information OSPF Support for Multi-VRF on CE Routers Last Updated: June 24, 2011 The OSPF Support for Multi-VRF on CE Routers feature provides the
Chapter 5 Lab 5-1, Configure and Verify Path Control
hapter 5 Lab 5-1, onfigure and Verify Path ontrol Topology Objectives Background onfigure and verify policy-based routing. Select the required tools and commands to configure policy-based routing operations.
Chapter 4 Lab 4-3, Manipulating Administrative Distances
hapter 4 Lab 4-3, Manipulating Administrative Distances Topology bjectives Background onfigure RIP on a router. onfigure SPF on a router. Manipulate administrative distances. ompare routing protocol behavior.
Shortcut Switching Enhancements for NHRP in DMVPN Networks
Shortcut Switching Enhancements for NHRP in DMVPN Networks Routers in a Dynamic Multipoint VPN (DMVPN) Phase 3 network use Next Hop Resolution Protocol (NHRP) Shortcut Switching to discover shorter paths
Case Study 2: Frame Relay and OSPF Solution
Case Study 2: Frame Relay and OSPF Solution Objective In this case study, you troubleshoot a complex scenario involving Frame Relay and Open Shortest Path First (OSPF). Figure 2-1 shows the topology for
Activity 2.5.1: Basic PPP Configuration
Activity 2.5.1: Basic PPP onfiguration Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 Fa0/1 192.168.10.1 255.255.255.0 N/A S0/0/0 10.1.1.1 255.255.255.252
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
Chapter 4 Lab 4-2, Redistribution Between EIGRP and OSPF
Chapter 4 Lab 4-2, Redistribution Between EIGRP and OSPF Topology Objectives Review EIGRP and OSPF configuration. Redistribute into EIGRP. Redistribute into OSPF. Summarize routes in EIGRP. Filter routes
Chapter 6 Lab 6-4, BGP Route Reflectors and Route Filters
Chapter 6 Lab 6-4, BGP Route Reflectors and Route Filters Topology Objectives Background Configure IBGP routers to use a route reflector and a simple route filter. The International Travel Agency maintains
CCNA Exploration: Routing Protocols and Concepts Chapter 10 Case Study
Objectives: Use OSPF single area to illustrate basic Link State components and operation. Migrate from EIGRP to OSPF single area. Intro: Trevni Inc. decided to upgrade their routing protocol from EIGRP
Chapter 1 Lab 1-1, Single-Area OSPF Link Costs and Interface Priorities
Chapter 1 Lab 1-1, Single-Area OSPF Link Costs and Interface Priorities Topology Objectives Configure single-area OSPF on a router. Advertise loopback interfaces into OSPF. Verify OSPF adjacencies. Verify
Understanding and Configuring the ip unnumbered Command
Understanding and onfiguring the ip unnumbered ommand Document D: 13786 ontents ntroduction Prerequisites Requirements omponents Used onventions What is an Unnumbered nterface? P and P Unnumbered onfiguration
CIS 83 LAB 2 - Single Area OSPF Rich Simms September 12, Objective. Scenario. Topology
CIS 83 LAB 2 - Single Area OSPF Rich Simms September 12, 2006 Objective The objective of this lab is to become familiar setting up and configuring OSPF on three routers for a single area. OSPF is our first
RIP. Table of Contents. General Information. Summary. Specifications
RIP Document revision 1 (Wed Mar 24 12:32:12 GMT 2004) This document applies to V2.8 Table of Contents Table of Contents General Information Summary Specifications Related Documents Additional Documents
Troubleshooting LSP Failure in MPLS VPN
Troubleshooting LSP Failure in MPLS VPN Document ID: 23565 Contents Introduction Prerequisites Requirements Components Used Conventions Network Diagram Router Configurations Problem Cause of the LSP Failure
Chapter 3 Lab 3-2, Multi-Area OSPF with Stub Areas and Authentication
NPv6 ROUTE hapter 3 Lab 3-2, Multi-Area OSPF with Stub Areas and Authentication Topology Objectives Background onfigure multiple-area OSPF on a r. Verify multiple-area behavior. onfigure OSPF stub, totally
AS 100 AS 300. Lab -1 Private Communities - II .1 S1/2. Task 1. On R1: / / /24. Configure the above topology.
Lab -1 Private Communities - II AS 100.1 R1 S1/2 12.1.1.0/24 S1/1.2 R2 S1/3 S1/3 13.1.1.0/24 23.1.1.0/24 S1/1.3 R3 S1/2 Lo0 6.6.6.0/24 Lo1 7.7.7.0/24 AS 300 Task 1 Configure the above topology. On R1:
Disclaimer. IOS used: c7200-p-mz s.bin. Page1
MPLS Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made to ensure that all material is as complete
Lab 4: Routing using OSPF
Network Topology:- Lab 4: Routing using OSPF Device Interface IP Address Subnet Mask Gateway/Clock Description Rate Fa 0/0 172.16.1.17 255.255.255.240 ----- R1 LAN R1 Se 0/0/0 192.168.10.1 255.255.255.252
Lab 8.4.2: Show IP Route Challenge Lab
Addressing Table Device Interface IP Address Subnet Mask R1 R2 R3 R4 R5 Learning Objectives Upon completion of this lab, you will be able to: Determine network topology based on the outputs from the show
IPv6 BGP AS Path. R1 Router Config:! ipv6 unicast-routing ipv6 cef. R4 Router Config:! ipv6 unicast-routing ipv6 cef Page1
IPv6 IPv6 BGP AS Path Disclaimer This Configuration Guide is designed to assist members to enhance their skills in particular technology area. While every effort has been made to ensure that all material
Step 1: IP Configuration: On R1: On R2: On R3: R1(config)#int s1/2 R1(config-if)#ip addr R1(config-if)#no shu
Step 1: IP Configuration: n R1: R1(config)#int s1/2 R1(config-if)#ip addr 12.1.1.1 255.255.255.0 R1(config-if)#no shu R1(config-if)#int lo0 R1(config-if)#ip addr 1.1.1.1 255.0.0.0 R1(config-if)#int lo1
Configure Initial Router Settings on Cisco 4000 Series ISRs
Configure Initial Router Settings on Cisco 4000 Series ISRs This chapter describes how to perform the initial configuration on Cisco 4000 Series Integrated Services Routers (ISRs). It contains the following
Configuring Easy Virtual Network Shared Services
Configuring Easy Virtual Network Shared Services This chapter describes how to use route replication and redistribution to share services in an Easy Virtual Network (EVN). Finding Feature Information,
Lab - Configuring Multi-area OSPFv3 Topology
Topology 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 8 Addressing Table Device Interface IPv6 Address R1 R2 R3 S0/0/0 (DCE) Lo0 Lo1 Lo2 Lo3 S0/0/0 S0/0/1
Lab Configuring Per-Interface Inter-VLAN Routing (Solution)
(Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/0 192.168.20.1 255.255.255.0 N/A G0/1 192.168.10.1 255.255.255.0 N/A S1 VLAN 10 192.168.10.11
STUDENT LAB GUIDE CCNA ( )
STUDENT LAB GUIDE CCNA (640-802) Developed By, Router Infotech Career Academy LAB: 09 Static Route Configuration Objective: To configure & implement Static Route successfully on said devices and test its
Lab 19a. Router On A Stick
Rev. 00.0 Lab a. Router On A Stick c cnac o okbook.com G O A L Configure routing on R, enabling host H to communicate with host H, then make VLAN 0 native on the trunk. Topology You'll need A router (R)
Lab Configuring Per-Interface Inter-VLAN Routing (Instructor Version)
(Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask
Configuring Redundant Routing on the VPN 3000 Concentrator
Configuring Redundant Routing on the VPN 3000 Concentrator Document ID: 13354 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Router Configurations
address-family ipv4 vrf vrf-name - Selects a per-vrf instance of a routing protocol.
LAB 1: Initial MPLS VPN Setup LAB 2: Running OSPF between PE and CE Routers LAB 3: Running BGP between PE and CE Routers LAB 4: Overlapping VPNs LAB 1: Initial MPLS VPN Setup Introduction: Introduction
Config. Router# show ip ospf
Config cc na c ookb ook.com R1(config)#router ospf 10 R1(config-router)#router-id 0.0.0.1 Do router-id first, before relationships are formed using it R3(config-router)#do clear ip ospf process Necessary