ids24gf User s Manual Industrial Modbus Gateway Industrial 16-port Serial-to-Ethernet Device Server

Transcription

1 Industrial Modbus Gateway Industrial 16-port Serial-to-Ethernet Device Server Version 1.1 June, 2015

2 COPYRIGHT NOTICE Copyright 2013 is5 Communications Inc. All rights reserved. No part of this publication may be reproduced in any form without the prior written consent of is5 Communications Inc. (is5). TRADEMARKS is5com is a registered trademark of is5. All other trademarks belong to their respective owners. REGULATORY COMPLIANCE STATEMENT Product(s) associated with this publication complies/comply with all applicable regulations. Please refer to the Technical Specifications section for more details. WARRANTY is5 warrants that all products are free from defects in material and workmanship for a specified warranty period from the invoice date (5 years for most products). is5 will repair or replace products found to be defective within this warranty period including shipping costs. This warranty does not cover product modifications or repairs done by persons other than is5-approved personnel, and this warranty does not apply to products that are misused, abused, improperly installed, or damaged by accident. Please refer to the Technical Specifications section for the actual warranty period(s) of the product(s) associated with this publication. DISCLAIMER Information in this publication is intended to be accurate. is5 shall not be responsible for its use or infringements on third-parties as a result of its use. There may occasionally be unintentional errors on this publication. is5 reserves the right to revise the contents of this publication without notice. CONTACT INFORMATION is5 Communications Inc. # Pacific Circle, Mississauga, Ontario, L5T 2A3 Tel: // Fax: Website: Technical Support support@is5com.com Sales Contact sales@is5com.com is5 Communications Inc 1

3 Table of Content COPYRIGHT NOTICE... 0 TRADEMARKS... 1 REGULATORY COMPLIANCE STATEMENT... 1 WARRANTY... 1 DISCLAIMER... 1 CONTACT INFORMATION... 1 Getting Started About the ids24gf Software Features Hardware Specifications... 4 Hardware Overview Front Panel Ports and Connectors LED Back Panel Ports and Connectors... 6 Hardware Installation Rack-mount Installation Wiring Power Inputs Fault Relay Connection Ethernet Port Pin Assignment SFP Serial Port Pin Assignment is5 Communications Inc 2

4 3.3.4 RS-232 Console Port Pin Assignment Management Basic Settings LAN Serial Setting Serial Configuration Port Profile Service Mode Virtual COM Mode TCP Server Mode TCP Client Mode UDP Client Mode Modbus RTU Slave Mode Modbus RTU Master Mode Modbus ASCII Slave Mode Modbus ASCII Master Mode System Tools Login Setting Date & Time Device Restart Firmware Upgrade Save/Restore Configurations Miscellaneous Event Warning Settings System Log SMTP SNMP Settings System Status System Info Technical Specifications is5 Communications Inc 3

5 Getting Started 2.1 About the ids24gf The ids24gf is a RS-232/422/485-to-LAN device server with 16 serial ports and 6 Ethernet ports (4 Copper and 4 SFP ports optional). Besides standard features such TCP/IP interface and versatile operation mode support (Virtual Com, TCP Server, TCP Client, UDP, Modbus RTU Master and Slave modes and Modbus ASCII Master and Slave modes), the device can be managed using the Windows untility, DS-Tool, which allows you to configure multiple devices and set up the mappings of Virtual Com. On the other hand, ids24gf can simultaneously transfer data to up to five redundant host PCs to aovid Ethernet connection breakdown or any host PC failure. In compliance with the EN50155 standard, the device provides 4x10/100/1000Base-T(X) Ethernet ports and 2x100/1000Base-X SFP ports to meet demand for high bandwidth and long distance transmission. With a wide operating temperature from -40 o C to 70 o C, the device is ideal for harsh industrial environments. 2.2 Software Features Redundant multiple host devices including TCP Client and UDP modes with four IP ranges Supports multiple operating modes such as Virtual Com, TCP Server, TCP Client, UDP, Modbus RTU Master, Modbus RTU Slave, Modbus ASCII Master, Modbus ASCII Slave Update DNS hostname: DDNS Event warning by Syslog, , SNMP trap, and beeper Configurable by Web Interface and ids Tool Various Windows OS. supported: Windows NT/2000/ XP/ 2003/VISTA(32/64bit)/ Windows 7(32/64bit) 2.3 Hardware Specifications 4 x 10/100/1000Base-T(X) Ethernet ports 2 x 100/1000Base-X SFP ports ( option ) 16 x serial ports (RJ48 or/and DB9 connectons) EN50155 compliance for rolling stock application VAC power supply Operating Temperature: -40 to 85 o C Storage Temperature: -40 to 85 o C Operating Humidity: 5% to 95%, non-condensing Dimensions: 440 (W) x 325 (D) x 44 (H) mm is5 Communications Inc 4

6 Hardware Overview 2.4 Front Panel Ports and Connectors The device provides the following ports on the front panel, including four RJ-45 Ethernet ports, two SFP ports, and sixteen RJ48 serial ports Port LAN slots SFP port Serial port Power connector 4 x 10/100/1000Base-T(X) ports 2 x 100/1000Base-T(X) ports (option) 16 x RS-232/422/485 ports 1 x VAC with power socket 1. Serial ports 2. RJ-45 Ethernet LAN ports 3. SFP ports 4. Console port 5. Data transmitting/receiving LED for serial ports 6. Reset button 7. Power LEDs 8. Link/action LED for Ethernet ports is5 Communications Inc 5

7 2.1.2 LED LED Color Status PWR1 Green On Power module is activated Amber On Power module is inactivated PWR3 Green On Power module is activated Amber On Power module is inactivated Fault Amber On Fault alarm exists Amber OFF No fault alarm ETH LNK/ACT Green On Port is running at 1000Mbps Amber On Port is running at 10/100Mbps. SFP LNK/ACT Green On Port is linked Serial TX / RX Amber On Port is receiving data Green On Port is transmitting data 2.5 Back Panel Ports and Connectors is5 provides several configuration options for ids24gf serial server to meet various customer requirements. Please refer to the following table for available configuration. Module is5com # Serial Port 1-4 XX 4RJ48 4DB9 4BNC None 4 X RS232/422/485 RJ45 Serial Ports 4 X RS232/422/485 DB9 Serial Ports 2 X IRIB B - 2 In and 2 Out (Future) Serial Port 5-8 XX 4RJ48 4DB9 4BNC None 4 X RS232/422/485 RJ45 Serial Ports 4 X RS232/422/485 DB9 Serial Ports 2 X IRIB B - 2 In and 2 Out (Future) Serial Port 9-12 XX 4RJ48 4DB9 4BNC None 4 X RS232/422/485 RJ45 Serial Ports 4 X RS232/422/485 DB9 Serial Ports 2 X IRIB B - 2 In and 2 Out (Future) is5 Communications Inc 6

8 Serial Port Ethernet Ports 1-4 Ethernet Ports 5&6 XX 4RJ48 4DB9 4BNC 1V24 1V90 2SIM 1GSM 2GSM 1EVD 2EVD 1GSM1EVD XX 4GRJ45 XX 2GSFP None 4 X RS232/422/485 RJ45 Serial Ports 4 X RS232/422/485 DB9 Serial Ports 2 X IRIB B - 2 In and 2 Out (Future) V.24 Modem (Future) V.90 Modem (Future) Dual SIM GPRS/UMTS (Future) 1 Port Cell Modem GSM,EDGE,HSPA (Future) 2 Port Cell Modem GSM,EDGE,HSPA (Future) 1 Port Cell Modem EVDO (Future) 2 Port Cell Modem EVDO (Future) 1 Port Cell Modem GSM,EDGE,HSPA, 1 Port Cell Modem EVDO (Future) None 4 X 10/100/1000 Base TX RJ45 None 2 X 100/1000 Base X SFP** (Blank No Transceivers) The device provides the following connectors on the back panel: Power Supply PWR1 PWR VDC 36-72VDC VDC or VAC None 10-48VDC 36-72VDC VDC or VAC is5 Communications Inc 7

9 1. Power Connector Hardware Installation 3.1 Rack-mount Installation The device comes with two rack-mount kits to allow you to fasten the device to a rack in any environments. Rack-mount Kit Measurement (unit = mm) Follow the following steps to install the device to a rack. Step 1: Install left and right front mounting brackets to the device using 4 screws on each side. Step 2: With front brackets orientated in front of the rack, fasten the brackets to the rack using two more screws. Note: You can install the brackets on both sides at back of the device and mount it to the rack with the rear panel facing outward if the space for front panel cabling is limited. Remember, when installing the brackets on the front sides, use the four screw holes at the top and bottom. is5 Communications Inc 8

10 When installing the brackets on the back sides, use the four screw holes at the top and middle. 3.2 Wiring WARNING Do not disconnect modules or wires unless power has been switched off or the area is known to be non-hazardous. The devices may only be connected to the supply voltage shown on the type plate. ATTENTION 1. Be sure to disconnect the power cord before installing and/or wiring your devices. 2. Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. 3. If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your equipment. 4. Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point. 5. Do not run signal or communications wiring and power wiring through the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately. 6. You can use the type of signal transmitted through a wire to determine which wires should be kept separate. The rule of thumb is that wiring sharing similar electrical characteristics can be bundled together 7. You should separate input wiring from output wiring 8. It is advised to label the wiring to all devices in the system Power Inputs The ids24 supports dual redundant power supplies, Power Supply 1 (PWR1) and Power Supply 2 (PWR2). The connections for PWR1 and PWR2 are located on the terminal block. To connect power, follow the steps below: 2 Remove the cover designed for protection from the terminal block. 3 Connect the ground from the first power source to GND1 terminal screw. 4 Connect the Positive or Live from the first power source to the POWER 1 V+/L terminal is5 Communications Inc 9

11 screw. 5 Connect the Negative or Neutral from the first power source to the POWER 1 V-/N terminal screw. 6 If a redundant power supply is required repeat steps 2 to 4 connecting the wires from the second power source to the POWER 2 terminal screws. 7 To keep the wires from pulling loose, use a small flat-blade screwdriver to tighten the wire-clamp screws on the front of the terminal block connector. 8 After wiring is completed, put the transparent cover back onto the terminal block Fault Relay The relay contact of the terminal block connector is used to detect user-configured events. The switch provides fail open and fail close options to form relay circuits based on requirements. The contacts are energized upon power-up of the unit and remain energized unless a critical error occurs. One common application for this output is to signal an alarm if a power failure or removal of control power occurs. is5 Communications Inc 10

12 3.3 Connection Ethernet Port Pin Assignment The device is equipped with standard Ethernet ports. According to the link type, the device uses CAT 3, 4, 5,5e UTP cables to connect to any other network devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable specifications. Cable Types and Specifications: Cable Type Max. Length Connector 10BASE-T Cat. 3, 4, ohm UTP 100 m (328 ft) RJ BASE-TX Cat ohm UTP UTP 100 m (328 ft) RJ BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328ft) RJ-45 With 10/100Base-T(X) cables, pins 1 and 2 are used for transmitting data, and pins 3 and 6 are used for receiving data. 10/100Base-T(X) RJ-45 Port Pin Assignements: Pin Number Assignment 1 TD+ 2 TD- 3 RD+ 6 RD- 1000Base-T RJ-45 Port Pin Assignments: Pin Number Assignment 1 BI_DA+ 2 BI_DA- 3 BI_DB+ 4 BI_DC+ 5 BI_DC- 6 BI_DB- 7 BI_DD+ 8 BI_DD- The device supports auto MDI/MDI-X operation. You can use a cable to connect the device to a PC. The table below shows the 10/100Base-T(X) MDI and MDI-X port pin outs. is5 Communications Inc 11

13 10/100Base-T(X) MDI/MDI-X Pin Assignments: Pin Number MDI port MDI-X port 1 TD+(transmit) RD+(receive) 2 TD-(transmit) RD-(receive) 3 RD+(receive) TD+(transmit) 4 Not used Not used 5 Not used Not used 6 RD-(receive) TD-(transmit) 7 Not used Not used 8 Not used Not used 1000Base-T MDI/MDI-X Pin Assignments: Pin Number MDI port MDI-X port 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_DC+ 8 BI_DD- BI_DC- Note: + and - signs represent the polarity of the wires that make up each wire pair SFP The switch comes with SFP ports that can connect to other devices using SFP modules. The SFP modules are hot-swappable input/output devices that can be plugged into the SFP ports to connect the switch with the fiber-optic network. Remember that the TX port of Switch A should be connected to the RX port of Switch B. Switch A Switch B Fiber cord is5 Communications Inc 12

14 1. Insert clean dust plugs into the SFPs after the cables are extracted from them. 2. Clean the optic surfaces of the fiber cables before you plug them back into the optical bores of another SFP module. 3. Avoid getting dust and other contaminants into the optical bores of your SFP modules in cases of malfunction Serial Port Pin Assignment The device provides serial ports in RJ48 connector type. Please refer to the following table for pin assignment. Pin # RS-232 RS-422 RS-485 (4 wire ) RS-485 (2 wire ) 1 DCD TXD - TXD - DATA- 2 RXD TXD + TXD + DATA+ 3 TXD RXD + RXD + 4 DTR RXD - RXD - 5 GND GND GND GND 6 DSR 7 RTS 8 CTS 9 RI RS 232 mod act as DTE The device provides serial ports in DB9 connector type. Please refer to the following table for pin assignment. Pin # RS-232 RS-422 RS-485 (4 wire ) RS-485 (2 wire ) 1 DCD TXD - TXD - DATA- 2 RXD TXD + TXD + DATA+ 3 TXD RXD + RXD + 4 DTR RXD - RXD - 5 GND GND GND GND 6 DSR 7 RTS 8 CTS 9 RI RS 232 mod act as DTE is5 Communications Inc 13

15 3.3.4 RS-232 Console Port Pin Assignment The ids24gf can be managed via the console port using the RS-232 cable supplied with the switch. Connect the port to a PC using the RS-232 cable with a DB-9 female connector. The DB-9 female connector of the RS-232 cable should be connected the PC while the other end of the cable (RJ-45 connector) should be connected to the console port of the switch. DB9 PC pin out (male) RS-232 cable, female DB9 connector RS-232 cable, RJ 45 connector Pin #2 RD Pin #2 TD Pin #2 TD Pin #3 TD Pin #3 RD Pin #3 RD Pin #5 GD Pin #5 GD Pin #5 GD is5 Communications Inc 14

16 Management The device can be managed via a built-in web server which supports Internet Explorer (Internet Explorer 5.0 or above versions) and other Web browsers such as Chrome. Therefore, you can manage and configure the device easily and remotely. You can also upgrade firmware via a Web browser. The Web management function not only reduces network bandwidth consumption, but also enhances access speed and provides a user-friendly viewing screen. Note: By default, IE5.0 or later version do not allow Java applets to open sockets. You need to modify the browser setting separately in order to enable Java applets for network ports. Management via Web Browser Follow the steps below to manage your device via a Web browser System Login 1. Launch an Internet Explorer. 2. Type and the IP address of the device. Press Enter. 3. A login screen appears. 4. Type in the username and password. The default username and password is admin. 5. Press Enter or click OK, the management page appears. Note: you can use the following default values: IP Address: Subnet Mask: Default Gateway: User Name: admin is5 Communications Inc 15

17 Password: admin After logging in, you will see the information of the device as below. On the left hand side of the management interface shows links to various settings. Clicking on the links will bring you to individual configuration pages. 4.1 Basic Settings LAN This page allows you to configure the IP settings of the LAN interface of the device. The LAN IP address is private to your internal network and is not visible to Internet. is5 Communications Inc 16

18 Label Device Name IP Address Subnet Mask Gateway Modbus TCP Port Apply Cancel Enter the name of your device The IP address of the LAN. Default: The subnet mask of the LAN. Default: Default Gateway IP address. Default: Enable - enable Modbus service in ids24 platform Disable disable Modbus service in ids24 platform Default: disabled. The ports configuration for Modbus service. Default: 502 Click Apply to activate the configuration Click Cancel to cancel the configuration 4.2 Serial Setting Serial Configuration This page allows you to configure serial port parameters. is5 Communications Inc 17

19 Label Port Select the port that the configuration is applied to. Port Alias The given name of the port. The default are: port1, port2.port16 Interface Select an interface type for your serial device. Available options are: RS-232, RS-422, RS-485-2W, and RS-485-4W. The default is RS232 Baud Rate The baud rate can be set to: 110, 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600, , , or bps. The default is bps Data Bits Select the number of data bits to transmit. You can configure data bits to be 5, 6, 7, or 8. Data is transmitted as a series of five, six, seven, or eight bits (five and six bit data formats are used rarely for specialized communications equipment). The default is 8 Stop Bits Select the number of bits used to indicate the end of a byte. You can configure stop bits to be 1 or 1.5(2). If Stop Bits is 1.5, the stop bit is transferred for 150% of the normal time used to transfer one bit. Both the computer and the peripheral device must be configured to transmit the same number of stop bits. Parity Select the method of detecting errors in transmission. Parity control bit modes include None, Odd, Even, Mark, and Space. None: parity checking is not performed and the parity bit is not transmitted. None is the most common parity setting with error detection handled by a communication protocol. Odd: the last data bit transmitted will be a logical 1 if the data transmitted had an odd amount of 0 bits Even: the last data bit transmitted will be a logical 1 if the data transmitted had an even amount of 0 bits. Mark: the parity bit is always set to the mark signal condition (logical 1) Space: the last transmitted data bit will always be a logical 0 The default is None Flow Control Serial communication consists of hardware flow control and software flow control, so called as the control is handled by is5 Communications Inc 18

20 Force TX Interval Time Performance Apply Cancel software or hardware. XOFF and OXN is software flow control while RTS/CTS or DTR/DSR is hardware flow control. Choose XOFF to tell the computer to stop sending data; then the receiving side will send an XOFF character over its Tx line to tell the transmitting side to stop transmitting. Choose XON to tell the computer to begin sending data again; then the receiving side will send an XON character over its Tx line to tell the transmitting side to resume transmitting. In hardware flow control mode, when the device is ready to receive data, it sends a CTS (Clear To Send) signal to the device on the other end. When a device has something it wants to send, it will send a RTS (Ready To Send) signal and waits for a CTS signal to come back its way. These signals are sent apart from the data itself on separate wires. The default is None This setting will specify the timeout when no data has been transmitted. When the timeout is reached or TX buffer is full (4K Bytes), the queued data will be sent. 0 means disable. The default value is 0. Throughput: This mode is optimized for the highest transmission speed. Latency: This mode is optimized for the shortest response time. The default is Throughput. Click Apply to activate the configuration Click Cancel to cancel the configuration is5 Communications Inc 19

21 4.2.2 Port Profile Label Port Local TCP Port Command Port Flush Data Buffer After Delimiter (Hex 0-ff) Apply Cancel Select the port that the configuration is applied to. Indicates the TCP port the device uses to listen to connections, and that other devices must use to contact the device. To avoid conflicts with well-known TCP ports, the default is set to Indicates the listen TCP port for IP-Serial Lib commands from the host. In order to prevent a TCP port conflict with other applications, the user can set the Command port to another port if needed. The received data will be queuing in the buffer until all the delimiters are matched. When the buffer is full (4K Bytes) or after Flush Data Buffer After times out the data will also be sent. You can set the time from 0 to seconds. For advanced data packing options, you can specify delimiters for Serial to Ethernet and / or Ethernet to Serial communications. You can define max. 4 delimiters (00~FF, Hex) for each way. The data will be hold until the delimiters are received or the option Flush Serial to Ethernet data buffer times out. 0 means disable. Factory default is 0. Click Apply to activate the configuration Click Cancel to cancel the configuration is5 Communications Inc 20

22 4.2.3 Service Mode Virtual COM Mode In Virtual COM mode, the driver establishes a transparent connection between the host and the serial device by mapping the port of the serial server to a local COM port on the host computer. Virtual COM mode also supports up to 5 simultaneous connections, so that multiple hosts can send or receive data by the same serial device at the same time. Label Port Select the port that the configuration is applied to. Data Encryption Click Enable and the data will be encrypted with SSL. When serial port stops data transmission for a defined period of time (Idle Timeout), the connection will be closed and the port will Idle Timeout be freed and try to connect with other hosts. 0 indicate disable this function. Factory default value is 0. If Multilink is configured, only the first host connection is effective for this setting. The serial device will send TCP alive-check package in each defined time interval (Alive Check) to remote host to check the Alive Check TCP connection. If the TCP connection is not alive, the connection will be closed and the port will be freed. 0 indicate disable this function. Factory default is 0. The number of maximum connections can be supported. The Max Connection maximum value is 5, default values is 1. Apply Click Apply to activate the configuration Cancel Click Cancel to cancel the configuration *Not allowed to mapping Virtual COM from web is5 Communications Inc 21

23 TCP Server Mode In TCP Server mode, IMG is configured with a unique port combination on a TCP/IP network. In this case, IMG waits passively to be contacted by the device. After the device establishes a connection with the serial device, it can then proceed with data transmission. The TCP Server mode also supports up to 5 simultaneous connections, so that multiple device can receive data from the same serial device at the same time. Label Port Data Encryption TCP Server Port Idle Timeout Alive Check Max Connection Apply Cancel Select the port that the configuration is applied to. Click Enable and the data will be encrypted with SSL. Set the port number for data transmission. When serial port stops data transmission for a defined period of time (Idle Timeout), the connection will be closed and the port will be freed and try to connect with other hosts. 0 indicate disable this function. Factory default value is 0. If Multilink is configured, only the first host connection is effective for this setting. The serial device will send TCP alive-check package in each defined time interval (Alive Check) to remote host to check the TCP connection. If the TCP connection is not alive, the connection will be closed and the port will be freed. 0 indicate disable this function. Factory default is 0. The number of maximum connections can be supported. The maximum value is 5, default values is 1. Click Apply to activate the configuration Click Cancel to cancel the configuration is5 Communications Inc 22

24 TCP Client Mode In TCP Client Mode, the device can establish a TCP connection with the server by the method you set (Startup or any character). After the data has been transferred, the device can disconnect automatically from the server by using the TCP alive check time or idle timeout settings. Label Port Select the port that the configuration is applied to. Destination Host Set the IP address of host and the port number of data port.. When serial port stops data transmission for a defined period of time, the connection will be closed and the port will be freed and try Idle Timeout to connect with other hosts. 0 indicates disable this function. Factory default value is 0. If multilink is configured, only the first host connection is effective for this setting. The serial device will send TCP alive-check packages in each defined time interval to remote host to check the TCP connection. If Alive Check the TCP connection is not alive, the connection will be closed and the port will be freed. 0 indicate disable this function. Factory default is 0. is5 Communications Inc 23

25 Startup: the TCP Client will build TCP connection once the connected serial device is started. Connect Any Character: the TCP Client will build TCP connection once the connected serial device starts to send data. List of destination IP addresses of TCP server that TCP traffic is Destination Host sending to. Port TCP port that is used for TCP connection on the server side. Apply Click Apply to activate the configuration Cancel Click Cancel to cancel the configuration UDP Client Mode Compared to TCP communications, UDP is faster and more efficient. In UDP mode, you can uni-cast or multi-cast data from the serial device server to host computers, and the serial device can also receive data from one or multiple host. Label Port Listen Port Host Start/End IP Send Port Apply Cancel Select the port that the configuration is applied to. Allows the user to set a new TCP port number to listen on rather than the default value of the device If there are more than one destination hosts, specify the IP address range by inputting a value in Host Start / End IP. You can also auto scan the sending port number of the device Set the send port number. Click Apply to activate the configuration Click Cancel to cancel the configuration is5 Communications Inc 24

26 Modbus RTU Slave Mode The Modbus RTU Slave mode allows communications between a host computer and a slave device. After a host computer sends a command, the slave device processes the command and returns a response to the host computer. This process is repeated, allowing the host computer to monitor and control controller operation. Label Port TCP Server Port Max Connection Max Try Time Request Pause Response Wait Idle Timeout Apply Refresh Select the port that the configuration is applied to. Indicates the port used for the Modbus/TCP communication The total number of remote TCP/IP clients allowed to connect to this server. The maximum number of request retries performed serially. The delay between serial requests in milliseconds The serial response timeout in milliseconds Enter a TCP connection timeout in seconds. When no Modbus/TCP data is received within this timeout, the TCP connection will be dropped. Click Apply to activate the configuration Click Refresh to refresh the port configuration is5 Communications Inc 25

27 Modbus RTU Master Mode The ModBus RTU Master mode is used to connect to the serial device which runs as RTU slave. Serial port server will connect to the remote TCP Server, which is also called Modbus TCP Slave. Label Port Destination Host Idle Timeout Alive Check Apply Select the port that the configuration is applied to. Set the IP address of host and the port number of data port. When serial port stops data transmission for a defined period of time, the connection will be closed and the port will be freed and try to connect with other hosts. 0 indicate disable this function and is also the factory default value. If multilink is configured, only the first host connection is effective for this setting. The serial device will send TCP alive-check packages in each defined time interval to remote host to check the TCP connection. If the TCP connection is not alive, the connection will be closed and the port will be freed. 0 indicate disable this function. Factory default is 0. Click Apply to activate the configuration is5 Communications Inc 26

28 Modbus ASCII Slave Mode Modbus ASCII Slave mode works the same as Modbus/RTU Slave mode, except that the data format is Modbus/ASCII. Label Port TCP Server Port Max Connection Max Try Time Request Pause Response Wait Idle Timeout Apply Refresh Select the port that the configuration is applied to. Indicates the port used for the Modbus/TCP communication The total number of remote TCP/IP clients allowed to connect to this server. The maximum number of request retries performed serially. The delay between serial requests in milliseconds The serial response timeout in milliseconds Enter a TCP connection timeout in seconds. When no Modbus/TCP data is received within this timeout, the TCP connection will be dropped. Click Apply to activate the configuration Click Refresh to refresh the port configuration is5 Communications Inc 27

29 Modbus ASCII Master Mode Label Port Destination Host Idle Timeout Alive Check Apply Select the port that the configuration is applied to. Set the IP address of host and the port number of data port. When serial port stops data transmission for a defined period of time, the connection will be closed and the port will be freed and try to connect with other hosts. 0 indicate disable this function. Factory default value is 0. If Multilink is configured, only the first host connection is effective for this setting. The serial device will send TCP alive-check packages in each defined time interval to remote host to check the TCP connection. If the TCP connection is not alive, the connection will be closed and the port will be freed. 0 indicate disable this function. Factory default is 0. Click Apply to activate the configuration is5 Communications Inc 28

30 4.3 System Tools Login Setting Label Port Old Login Name Old Password New Login Name New Password Confirm New Password Apply Cancel Select the port that the configuration is applied to. This field shows the current login username. Enter the password you currently use to login the system if any. Enter a new login name containing characters in the range of '0-9', 'a-z', 'A-Z'. The length should be between 1 to 15 characters. An empty name is not acceptable. Enter a new login password. Acceptable characters of this field contains '0-9', 'a-z', 'A-Z' and must be between 0 to 15 characters in length. Retype the new password for confirmation. Acceptable inputs of this field contains '0-9', 'a-z', 'A-Z' and must be between 0 to 15 characters in length. Click Apply to activate the configuration Click Cancel to cancel the configuration is5 Communications Inc 29

31 4.3.2 Date & Time In this page, you can set the date & time of the device. A correct date and time will help the system log events. You can set up a NTP (Network Time Protocol) client to synchronize date & time with a NTP server on the Internet. Label NTP NTP Server 1 Time Zone Local Date Local Time Get Current Date & Time from Browser Apply Cancel Enables or disables NTP function The primary NTP server Select the time zone you are located in Set a local date manually Set a local time manually Click to set the time from your browser Click Apply to activate the configuration Click Cancel to cancel the configuration is5 Communications Inc 30

32 4.3.3 Device Restart This page allows you to configure restart settings for the router. Label Restart Now Click to restart the router via warm reset Firmware Upgrade is5 Communication launches new firmware constantly to enhance router performance and functions. To upgrade firmware, download new firmware from is5 s website to your PC and install it via Web upgrade. Make sure the firmware file matches the model of your router. It will take several minutes to upload and update the firmware. After upgrade completes successfully, reboot the router. During firmware upgrading, do not turn off the power of the router or press the reset button Save/Restore Configurations This page allows you to save configurations or return settings to previous status. You can download the configuration file from the Web. Note: users using old versions of Internet Explorer may have to click on the warning on top of the browser and choose Download File. is5 Communications Inc 31

33 Label Save Restore Mode Restore Factory Default Setting Click to save existing configurations as a file for future usage. You can restore configurations to previous status by installing a previous configuration file. To do this, choose Web Restore or Tftp Restore. If you choose Web Restore, you need to choose a file and click Web Restore. If you select Tftp Restore, fill in a Tftp server IP address and the file name before clicking Tftp Restore. Click to reset the router to the factory settings. The router will reboot to validate the default settings Miscellaneous This page enables you to run ping test which will send out ping packets to test if a computer is on the Internet or if the WAN connection is OK. Enter a domain name or IP address in the destination box and click Ping to test. is5 Communications Inc 32

34 4.3.7 Event Warning Settings When an error occurs, the router will notify you through system log, , SNMP, and relay. You can set up the targets or destinations which will receive error notifications in this page System Log Label Syslog Server IP Enter the IP address of a remote server if you want the logs to be stored remotely. Leave it blank will disable remote syslog. Syslog Server Port Specifies the port to be logged remotely. Default port is 514. Apply Click Apply to activate the configuration Cancel Click Cancel to cancel the configuration is5 Communications Inc 33

35 SMTP Label SMTP Server Server Port Address 1-4 Apply Cancel Enter a backup host to be used when the primary host is unavailable. Specifies the port where MTA can be contacted via SMTP server Enter the mail address that will receive notifications Click Apply to activate the configuration Click Cancel to cancel the configuration is5 Communications Inc 34

36 SNMP Settings Label SNMP Agent SNMP Trap Server 1-4 Community SysLocation SNMP (Simple Network Management Protocol) Agent is a service program that runs on the access point. The agent provides management information to the NMS by keeping track of various operational aspects of the AP system. You can enable or disable the function. Enter the IP address of the SNMP server which will send out traps generated by the AP. Community is a password to establish trust between managers and agents. Normally, public is used for read-write community. Specifies syslocation string is5 Communications Inc 35

37 SysContact Apply Cancel Specifies syscontact string Click Apply to activate the configuration Click Cancel to cancel the configuration 4.4 System Status System Info This page displays the detailed information of the router including model name, description, firmware version, WAN, LAN and wireless settings. is5 Communications Inc 36

38 Technical Specifications is5 Device Server Model ids24gf Physical Ports 10/100/1000Base-T(X) Ports in RJ45 Auto MDI/MDIX 100/1000Base-X with SFP port 4 2 (optional) RS-232 Serial Console Port RS-232 in DB9 connector with console cable bps, 8, N, 1 Serial Ports Connector Operation Mode Serial Baud Rate Up to RJ48 x 16 (10-pin RJ48) Up to DB9 x 16 (DB 9) RS-232/422/485-2w/485-4w 110 bps to Kbps Data Bits 7, 8 Parity odd, even, none, mark, space Stop Bits 1, 1.5, 2 RS-232 Flow Control TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND XON/XOFF, RTS/CTS, DTR/DSR Network Protocol Protocol ICMP, IP, TCP, UDP, DHCP, BOOTP, SSH, DNS, SNMP V1/V2c, HTTP/HTTPS, SMTP, DDNS, PPPoE LED indicators Power indicator 10/100/1000Base-T(X) port indicator RJ45 PWR / Ready: Green On: Power is on Green Blinking: Located by Administrator. Green for port Link/Act at 1000Mbps. Amber for port Link/Act at 10/100Mbps. 100/1000Base-X Fiber Port Indicator Serial TX / RX LEDs: Green for port Link/Act Amber: Serial port is receiving data Green: Serial port is transmitting data Power Power Input Power consumption (Typ.) Overload current protection Dual Power Supplies available in any combination of 10-48VDC (LV), 36-72VDC (MV) and VAC (50/60Hz)/ VDC TBD Present Physical Characteristic Dimension (W x D x H) Weight (g) 440 (W) x 325 (D) x 44 (H) mm TBD Environmental is5 Communications Inc 37

39 Storage Temperature -40 to 85 o C (-40 to 185 o F) Operating Temperature -40 to 85 o C (-40 to 185 o F) Operating Humidity 5% to 95% Non-condensing Regulatory approvals EMI EMS Shock Free Fall Vibration Safety Warranty FCC Part 15, CISPR (EN55022) class A, EN50155 (EN , EN55011, EN ) EN (ESD) EN (RS), EN (EFT), EN (Surge), EN (CS), EN , EN IEC IEC IEC EN years is5 Communications Inc 38