ETH-1000 Version Info

Transcription

1 ETH-1000 Version Info Main CPU Firmware V5.600 Metasys, FLN release Added ability to release an object s value to Metasys N2 Master. Added ability to release a point s value to Siemens FLN Master Main CPU Firmware V5.500 Modbus, Generic Serial, DMX-512 release Improved timeout detection in Modbus RTU Slave, Generic Serial Slave, and DMX-512 slave drivers to account for receive errors and packets not intended for the device. Fixed issue with timeout detection in Modbus RTU Sniffer and Generic Serial Slave drivers where a timeout could take twice as long under certain circumstances Main CPU Firmware V5.400 Modbus, Generic Serial, DMX-512 release Added timeout detection capability to Modbus Sniffer driver. Fixed issue with Modbus Sniffer detection of packets with strict 3.5 character gap time. Improved Generic Serial ASCII decimal data encoding and detection. Fixed issue with Generic Serial Slave ASCII decimal leading spaces for fixed length elements. Fixed issue in DMX-512 where receive errors on the first byte of the packet were ignored. Fixed issue in DMX-512 where characters with receive errors after the configured length caused the packet to not be processed V4.002 release Fixed issue in BACnet/IP Client where simultaneous write requests would not be serviced. Page 1 of 12

2 V5.300 Generic Serial release Added support to Generic Serial driver for handling leading + characters for ASCII decimal numbers V5.200 release Fixed issue where the serial driver would not detect errors on the first byte of a packet. Fixed issues with using the USB Virtual COM port with Windows 10. Added support for 7 data bits to the USB Pass-Through Mode V5.100 Generic Serial release Fixed issue with Generic Serial drivers where transactions with a large amount of variable sized packet data objects could cause the device to hang. Added support for the Database Matched Byte packet data object to Generic Serial drivers. Fixed issue where the serial driver would not detect errors on the first byte of a packet V5.000 release Added Generic Serial Master protocol. Added Generic Serial Slave protocol. Added support for Internal Float (ADF), Internal Integer (ADI), and Internal Byte (BD) object types to Metasys N2 Slave. Modified Siemens FLN Slave driver s interpretation of non-zero intercept values so that the physical value sent on the network matches the database value for LAI and LAO points. Fixed USB connection issue where the device is sometimes not detected by the USB host when plugging in the USB cable to an already powered device. V4.001 release Added support for a null PROFINET device name. Added NAT support to BACnet/IP BBMD driver. Added support for Alerton BBMD devices to BACnet/IP Client, Server, and BBMD Page 2 of 12

3 BACnet BTL Changes (IP and MS/TP) Enabled support for Device Communication Control. Added data type checks to Present Value writes so that only the proper data type is allowed. Added support for configurable APDU Timeout. Added support for configurable Number of APDU Retries. Added support for APDU retries for confirmed requests. Made the following device properties network writable: APDU Timeout, Number of APDU Retries, and Max Master. Fixed issue with APDU Timeout timer where the timer started before the request was transmitted on the network. Added support for the Reliability property in all supported object types. Added support for configurable Number of States for Multi-state objects. Added support for Offset by One option for Multi-state objects for both Client and Server. Changed behavior of Multi-state Objects Present Value property so that it cannot go outside of the range 1 - Number of States. If the database value is out of that range, the FAULT Status Flag is set and the Reliability will be either Under Range or Over Range. Added error code when accessing Priority Array and Relinquish Default properties for virtual objects, because these properties are not supported. Added feature to BACnet client to detect if a server device is no longer online and begin transmitting Who-Is requests to it instead of continuing to send read or write requests. Removed support for 4800 baud rate, since the BACnet specification states the minimum is Updated Revision to 12. Updated Object Types Supported Device object property. Fixed Number of States datatype for Multi-state objects. Improved error handling and error responses for error conditions when handling all packets. Fixed issue with the ReadPropertyMultiple ALL properties for the Device object. Corrected the properties reported for ReadPropertyMultiple ALL, OPTIONAL, and REQUIRED for all objects. Fixed issue when reading a Device object property using the wildcard instance number where the Object ID in the response used the wildcard instance number instead of the device s actual instance number. Fixed NPoll token count from 52 to 50. Added password to ReinitializeDevice. Fixed issue where device would respond to Confirmed Broadcast Request packets. Fixed issue where the device would ignore Data Expecting Reply packets targeted to the broadcast address. Fixed issue where the device would not properly ignore packets not for us by adding the Skip Data state to the receive state machine. Fixed EventCount handling error in MS/TP Master Node State Machine as described in addendum d-8. Fixed poll for master to self issue in the DONE_WITH_TOKEN and PASS_TOKEN states. Added support to SubscribeCOV for the situation where the Lifetime argument is omitted from the request and should be assumed to be 0 (indefinite lifetime). Fixed issue where a COV could be issued after the COV has expired. Page 3 of 12

4 Added support to initiate a COV notification after receiving a subscribe COV request. Fixed issue with reading the ACTIVE_COV_SUBSCRIPTIONS property of the device object. Fixed issue with reading the DEVICE_ADDRESS_BINDINGS property of the device object. Fixed issues with configured Relinquish Default value data type conversion. Fixed issue with Susbscribe COV requests Lifetime parameter not supporting the full Unsigned range. Fixed error code returned when a Subscribe COV request is received for the Device object. Fixed issue with DeviceCommunicationControl Time Duration timer not supporting the full Unsigned range. Fixed error code returned when a ReinitializeDevice request is received after a DeviceCommunicationControl DISABLE request is received. Fixed issue with COV Increment property s internal unused signifier value. Set maximum limit on Multi-state Number Of States property so that the internal reserved NULL value cannot be used. Added error reporting for BACnet Client when a Diagnostics object is used for Multi-state objects that have an invalid value. Fixed implementation of Device Instance wildcard value of to be interpreted as if the device instance matches. Optimized performance for scenarios where the device is connected to a live BACnet network while powered on. Relaxed MS/TP timing parameters to ensure the specified times are never violated January 1, V4.100 release Fixed issue where received bytes could be dropped during critical sections when the receiver is disabled. Changed BACnet MS/TP Client static device destination address limit to 254 to support MS/TP slave-only addresses. Added Protocol Format setting for the USB Serial Sniffer Settings protocol. Added Network Information which includes IP Address, Subnet Mask, and Default Gateway to the device information shown in the ICC Configuration Studio. Fixed issue where USB task may not be running if a fatal error occurs during startup. Added error code response to USB communications to prevent pipe stalls. Fixed packet corruption issue in USB serial sniffer when sniffer buffer overflows occur. Fixed issue with USB Serial Pass-Through mode. Improved the check device ready functionality with the ICC Configuration Studio. Improved compiler optimizations. Page 4 of 12

5 V3.022 release Modified EtherNet/IP to ignore socket address info items to improve the connection establishment Add Inverted, Auto Reset, and Bitmask trigger options to database logic enable triggers. Added Bit Copy, Indirect Copy, Flag Test & Set, Value Change Detection, Multiplexer, and Byte Reverse database logic operations. Ethernet network configuration settings now return the configured values instead of live values when uploaded by the ICC Configuration Studio. Added Network Information which includes IP Address, Subnet Mask, and Default Gateway to the device information shown in the ICC Configuration Studio. Improved booting time so that it is no longer dependent on the method used to obtain an IP address. Changed IP address acquisition behavior. GSDML file GSDML-V2.0-ICC-ETH_ xml Limit the lowest I/O cycle update time to 8ms Update the maximum input, output, and total sizes to account for overhead data April 1, V4.000 release Added floating point as a native database data type. Added USB Virtual COM Port support. Added FLN Master protocol. Added Toshiba Computer Link Master protocol. Added USB Serial Sniffer Settings protocol to use for packet capturing. Added Trigonometric Operations to Database Logic. Added Random operation to Database Logic. Fixed issue where writing to FLN LDO points fails. Added ability to relinquish written values in BACnet Client. Removed 0xFF byte pad in BACnet MS/TP packets. Improved packet handling for DMX-512 Slave driver. Fixed issues in M-Bus Master driver when decoding and encoding string values. Fixed issue with device info string displaying extra characters. Fixed issue with BACnet which could cause a duplicate packet to be sent 40 bit times after the first. Fixed issue in BACnet where the first reply to a poll for master was ignored if the last packet received was a partial packet. Page 5 of 12

6 Fixed issue in Modbus when converting negative 32-bit integer values to floating point. Optimized startup order of all tasks. Fixed BACnet DeviceCommunicationControl service. Corrected BACnet Protocol_Services_Supported Device property flags. Added check in Modbus Slave to respond with an exception to requests spanning multiple incompatible register remaps. Various code optimizations V4.000 release Added floating point as a native database data type. Added Trigonometric Operations to Database Logic. Added ability to relinquish written values in BACnet Client. Added write support for COV Increment property for BACnet Analog objects and added a configuration setting. Fixed detection of a dead socket due to a broken Ethernet link. Fixed internal update of the MELSEC (MC Protocol) Client configuration to be compatible with the new file format. Improved handling and recycling of network resources. Fixed issue with INCON client connection October 2, No changes V3.012 release Internal compatibility fix. Fix handling of database logic filtering operations when the operations are disabled. Added support to configure BACnet/IP UDP port November 20, V3.300 release Added database logic Page 6 of 12

7 Internal bug fixes. V3.010 release Added database logic Fixed INCON Client response data overflow July 31, Modbus-BACnet V3.100 release Added check to Modbus Master to compare received data bytes against the expected number of bytes. Metasys-Toshiba V3.100 release Fixed issue with Metasys Master writes with VMA devices V3.000 release Fixed issue in Metasys Slave driver which caused gateway to become non-responsive on some noisy networks. Added VMA device support for Metasys Master. Added Multi-state object support for BACnet Client and Server. Added range checking for writes for BACnet Server. Added ability to enable and disable the default mapping for Modbus Slave and BACnet Server. Added support for the ICC Configuration Studio. V3.004 release Modified the handling of modules after the PROFINET connection is terminated. The modification will improve the compatibility with the PROFINET controller on the subsequent connection. Added Generic Socket Client driver. Added Generic Socket Server driver. Added VeriSens Client driver. Added Multi-state object support for BACnet/IP Client. Added Multi-state object support for and BACnet/IP Server. Added range checking for writes for BACnet/IP Server. Added ability to enable and disable the default mapping for BACnet/IP Server. Added ability to enable and disable the default mapping for Modbus/TCP Server. Fixed Modbus/TCP Server handling of remap objects with a multiplier of 0. Relaxed EtherNet/IP Client API (actual packet interval) check. Relaxed EtherNet/IP Client multicast address check to accept any valid IP multicast address in the T O direction. Page 7 of 12

8 Added INCON Client driver. Added Green Fume Hood (GFH) Client driver. Modified the FTP server to improve Windows Explorer FTP compatibility. Removed Ethernet protocol configuration from the embedded web server. All Ethernet configuration will be completed via the Configuration Studio. Added support for the ICC Configuration Studio May 15, Metasys-Toshiba V2.400 release Fixed issue where ETH-1000 took too long to respond, due to COS checking, when many N2 objects were configured April 23, Modbus, BACnet V2.500 release Added default mapping for BACnet MS/TP Server Changed Modbus Sniffer Reflect Status to not update Current Status on TX Counter increments Fixed Modbus Slave remap scaling issues Improved coprocessor communication V2.330 release Increased Modbus/TCP Client max number of connection objects to 16 Added default mapping for BACnet/IP Server April 23, Chillgard V2.400 release A.O. Smith V2.300 release Added A.O. Smith AIN and PDNP drivers Page 8 of 12

9 Added support for different types of scaling for the concentration values including new % units in Chillgard Added support for more gas types in Chillgard V2.320 release Added BACnet BBMD support Added EtherNet/IP Client slot, element data type, database data type, and multiplier configurability January 15, V2.300 release Added DMX-512 Master and Slave drivers Added M-Bus Master driver Added function code 05 (Force Single Coil) to Modbus RTU Master driver Increased Service Object memory usage Fixed FLN response timing issues by caching data from coprocessor V2.300 release Added CSP Server logical ASCII addressing for both Typed Read and Typed Write commands Improved Modbus/TCP Client packet resynchronization Improved MELSEC Client packet resynchronization Added MELSEC Server driver Reduced max MELSEC client device points to 719 words, due to the 3E batch write command payload limitation Added Modbus/TCP Client support for function code 5 (Force Single Coil) Fixed directed broadcasts when the subnet mask is set to a value other than Added PROFINET IO support for timeout processing Added EtherNet/IP Server class 1 I/O support for point-to-point (unicast) in the T O direction Fixed MELSEC Client auto-detect to correctly detect 3E frames EtherNet/IP EDS file V2.1 Updated connection description to support point-to-point (unicast) in the T O direction August 15, 2011 Page 9 of 12

10 V2.200 release Added MSA Chillgard driver Added Metasys N2 Master driver Added Siemens FLN driver Added TCS Basys driver Fixed Modbus Master bug when Floating Point is checked and multiplier is 1, the value is now correctly converted as a floating point number Improved accuracy of Modbus multiplier scaling Updated Metasys Slave driver so that it won t reset the object configuration upon receiving the F command Fixed Modbus Slave remap object issues V2.200 release Fixed BACnet/IP Server response with Device Object character strings. The character set is now correctly set to ANSI X3.4. Fixed loading of BACnet/IP Server objects to the webpage when BACnet/IP Server is disabled Fixed BACnet/IP Server COVs from deadlocking and preventing the BACnet/IP Server driver from responding Fixed CSP Server endianness conversion Fixed MELSEC Client bypass request to search only the existing MELSEC connections to prevent index out of bounds error Added PROFINET IO support for slots 1 to February 1, V2.100 release Added Sullair master driver Added Modbus sniffer driver Added Enron/Daniel 32-bit Modbus extension to Modbus master and slave drivers In Modbus RTU slave driver, holding registers and input registers can now be remapped independently, and can have multipliers applied Decreased object memory usage for BACnet objects in BACnet MS/TP server driver BACnet MS/TP client driver now sends Who-Is for all configured destination devices on startup, not just statically bound ones Improved efficiency of service object handling in BACnet MS/TP client driver Fixed Poll-For-Master to self bug in BACnet MS/TP drivers Page 10 of 12

11 Fixed multiply by 1 rounding issues Fixed bug where master/client protocol would not generate a write after changing a value in the monitor tab of the Configuration Utility V2.100 release Added EtherNet/IP client produced tag connection configuration Increased range of produce, consume, and configuration connection points for EtherNet/IP client Class 1 message type configuration Allow a value of 0 for the produced and consumed byte count for EtherNet/IP client Class 1 message type configuration Increased max number of BACnet/IP server objects from 100 to 200 Added EtherNet/IP client explicit messaging scan rate Added BACnet/IP client driver Added support for BACnet/IP server SubscribeCOV service Added MELSEC client scan rate Added support for Enron/Daniel 32-bit extensions for Modbus/TCP client and server drivers Added Modbus/TCP client scan rate Added support for Modbus/TCP server remap register types March 1, V2.000 release Added Metasys N2 slave driver Added Toshiba ASD master driver Fixed bug whereby an RS-485 master/client would starve if service objects were mapped from an Ethernet master/client but not in any service objects Fixed bug where device info would leave remnants of old device information Attempts to write to BACnet binary inputs will now return an error Improved efficiency of scanning function for master protocols V2.000 release Added EtherNet/IP and CSP client driver Added PROFINET IO driver Added Modbus/TCP client driver Added support for MELSEC 1E frame types Removed MELSEC service object data type from other device code Redesigned web server Page 11 of 12

12 Improved efficiency of scanning function for client protocols October 30, V1.000 initial release V1.000 initial release July 1, 2009 Page 12 of 12