M4000 Version 4.1 Installation Guide

Transcription

1 Established 1981 Advanced Test Equipment Rentals ATEC (2832) M4000 Version 4.1 Installation Guide Requirements Downloading M4000 This document explains how to install the M4000 software version 4.1 on a laptop or the M4200C Controller. Laptop requirements are as follows: Operating system Windows 2000 or newer Web browser Microsoft Internet Explorer V5.0 or newer The M4200C Controller must run the M4200 Thermal printer driver as the default. To confirm that the M4200 Thermal driver is the default printer driver: 1. Open the Start menu and select Control Panel. 2. Select Printers and Other Hardware. 3. Open View installed printers and fax printers. 4. Confirm that M4200 Thermal is selected as the default (a black circle with a checkmark in it should appear next to the driver name in the list). If it is not the default printer, highlight the M4200 Thermal printer icon, open File on the menu and select Set as Default Printer. If the M4200 Thermal printer is not listed, please contact your Doble principal engineer or local representative. To download M4000 from the Doble web site: 1. Go to 2. Open the Support menu and click Downloads. 3. Click the M4000 link, and on the M4000 page, click the M4KV41.exe link. 4. Click Save to save the file to your hard disk, or click Run to run Setup.exe immediately. Go to Installing the Software on page 2. 72A Rev. A 12/2009 1

2 Installing the Software To install M4100: 1. Double-click the Setup.exe file. The Choose Setup Language window appears. It enables you to select the language in which the remaining setup instructions will be presented. 2. Select a language from the drop-down list and click OK. 3. Read the Welcome advisory information and, if acceptable, click Next. 4. Read the software license agreement and, if acceptable, click Yes. 5. In the Choose Destination Location window: Click Next to accept the default folder for the M4000 software. or Browse to another folder and click Next. 6. In the Select Program Folder window, choose a location for the M4000 program icon and click Next. The Laptop/M4200 Controller Options window appears. 7. Select these options as appropriate: Launch M4000 at Startup Automatically starts M4000 each time the PC or M4200 Controller is turned on. Set the serial port to COM2 (default is COM1) Select this option if you use an M4200 Controller, which always requires COM2. 8. Click Next. The Safety Settings window appears. These settings are stored as Registry entries and can be changed by users through the Tools/Configuration menu, unless access is restricted. Check marks appear in the options that are turned on by default. 2 72A Rev. A 12/2009

3 9. In the Safety Settings window, select the safety options as appropriate: Beeper is enabled Enables the warning beep that signals the beginning of each test (recommended). Both LV Leads must be inserted to run test Requires that both the red and blue leads be inserted into the test set to run a test (rarely used). Safety strobe is required to run test If the strobe bulb or cable fails, you can disable it so that you can continue testing. Safety switch must be released between tests Discourages users from artificially holding the safety switch down for the duration of several tests. Restrict the Safety Configuration settings Locks the above four selections so that they cannot be changed from within the application. 10. Click Next. The Auto-fill the Company Field window appears. Any name entered in this field automatically appears in the Company field whenever a new test form is created. 11. Enter a name or leave the field blank. Click Next. 72A Rev. A 12/2009 3

4 12. In the M4000 Language Support window, select one or more languages for the M4000 user interface. Click Next. The Choose the M4000 Data Directory window appears. This directory will store all results of tests run with the M4100 clipboard. 13. Accept the default directory or browse to a different directory. Click Next. The Start Copying Files window appears. It summarizes the configuration options you have selected. 14. If necessary, click Back to modify the setup options. Then click Next to start file installation. The Copying Resource Files window appears and displays a progress bar. When the process is complete, the Setup Complete window appears. 15. As appropriate, select these options: Yes, I want to view the ReadMe file. Yes, I want to launch M Click Finish. Running Multiple Versions of M4000 Updating the Firmware You can run multiple versions of M4000 by installing them in different directories. Be aware that whenever you switch from one version to another, M4000 prompts you to download new firmware. To prevent this prompt from appearing: 1. Locate the M4i.x0, BootBlok.x0, and Loader.x0 in the directory in which version 3.4 or 4.0 is installed. The default directory is C:\Program Files\Doble\M Copy these three files into the other M4000 directories. This section is for newer M4100 instruments only, with a serial number format of four digits, a numeral one, and four more digits (xxxx1xxxx). Introduction When M4000 is updated, new firmware is downloaded with it but not installed. The updated M4000 automatically checks the currently installed firmware and, if appropriate, displays a message stating that new firmware is available. Immediate upgrade is not required; you can wait for a suitable time. 4 72A Rev. A 12/2009

5 Time Requirements The firmware upgrade takes 25 to 30 minutes. The associated amplifier upgrade, which is sometimes required, takes an additional 15 minutes. Cable Requirements The USB cable supplied with the M4100 is required for this upgrade. You must manually install the USB driver for this cable. If the upgrade is attempted using a USB-to-RS232 adapter with the old serial cable, the upgrade will fail. Procedures for Firmware and Amplifier Firmware Update The following procedures describe how to upgrade the firmware, and how to upgrade the amplifier (PUC) firmware if necessary. Read This First! As you begin upgrading, please keep the following information in mind: Do not power cycle the M4100 during the upgrade. Power cycling during a firmware or amplifier firmware upgrade causes the M4100 to become unusable. You will have to ship the unit back to Doble for reconfiguration. If M4000 is accidentally closed during an upgrade, power cycle the M4100 and start the upgrade over again. Depending on the version of the firmware or amplifier firmware you are upgrading, an Error 101 message may appear after the upgrade completes successfully. Close it and continue with the upgrade process. 72A Rev. A 12/2009 5

6 Upgrading the Firmware To upgrade the firmware: 1. Open the Tools menu and select Update the Firmware. A warning message appears. NOTE Do not power cycle the M4100 during the upgrade for any reason! If power cycling occurs, the M4100 becomes unusable and must be shipped back to Doble for reconfiguration. 2. To start the upgrade, click Yes. Several progress bars appear during the upgrade. Depending on the version of the firmware being updated, an Error 101 message may appear after the upgrade is completed successfully. 3. Click OK and power cycle the M4100. Upgrading the Amplifier (Power Unit Control) To determine if the Amplifier (PUC) firmware needs to be updated: 1. Open the Diagnostic menu and select System Status. The M System Status Diagnostic window appears. 2. Press F2 to run the test. When complete, the Reported Status for each item should be Enabled. 3. Look at the M4100 Instrument Amplifier Version field. If it displays a: Blank The Amplifier/PUC cannot be upgraded in the field and unit must be returned to Doble for upgrading. Number Go to step A Rev. A 12/2009

7 4. Open the Tools menu and select Update the Amplifier Firmware. One of these messages appears: Error 105 Indicates that the amplifier firmware cannot be upgraded in the field. Click OK and power cycle the M4100. You can continue to use the instrument while you make arrangements to ship it to Doble for upgrade. Update the M4100 Amplifier Firmware NOTE Do not power cycle the M4100 during the upgrade for any reason! If power cycling occurs, the M4100 becomes unusable and must be shipped back to Doble for reconfiguration. Reporting Problems 5. To start the upgrade, click Yes. Several progress bars appear during the upgrade. Depending on the version of the firmware being updated, an Error 101 message may appear after the upgrade is completed successfully. 6. Click OK and power cycle the M Run another System Status test. The following data should appear: M4100 Instrument Firmware Version: M4100 Instrument Amplifier Version: 1.31 Please communicate any problems or enhancement requests to your Doble principal engineer or local Doble representative. 72A Rev. A 12/2009 7

8 8 72A Rev. A 12/2009