Generating Vectors Overview

Size: px
Start display at page:

Download "Generating Vectors Overview"

Transcription

1 Generating Vectors Overview Vectors are mathematically defined shapes consisting of a series of points (nodes), which are connected by lines, arcs or curves (spans) to form the overall shape. Vectors can be generated directly within by using the Vector Tools in the Assistant or on the top Vector toolbar (as shown). Vectors can be rectangles, squares, circles, polylines, ellipses, polygons, stars or text. These can be edited if required to make the final vectors to create a relief from. Vectors can also be imported from another drawing package, using the File Import menu option, or copied and pasted from another package using the standard Windows commands. Press Create New Model. Set the size as Height 150 and Width 150. Set the Datum in the middle of the model. Set the resolution as 600 x 600 points by using the slider. Once the model size has been set, the design can begin. Select OK. The model is now opened and the Vectors are generated in the 2D View. The 3D View is used for displaying the relief. From the Assistant or Vector toolbar, select the Create Rectangle icon.

2 The rectangle creation page appears, showing the options available. The rectangle can be created by clicking in the screen and dragging to a size, or by entering in the values. Several rectangles can be created without closing down the page. Each Assistant Page has help available, indicated by the word Show Help. Press Show Help. The Assistant displays help at the side of each option. Typically, this increases the length of the page and you will have to move the page down to see further instructions, by moving the bar down. Some commands have a video clip to show the command in use. Just press the video icon. Once help is switched on it is displayed for each command. To switch this off, you need to Hide the Help. Hide Help. Press down the left mouse button in the 2D view and drag a rectangle of any size.

3 The rectangle appears as dotted. The length and height can be dragged by moving the big squares in the middle of the sides. A radius can be put on the corners by dragging in one corner. The rectangle can be rotated by dragging around the lever in the centre. Click on a corner and drag inwards. A radius has been given to the corners of the rectangle. If you press Create the rectangle will be generated, leaving the form in creation mode. Press Create. Generate more rectangles, pressing space bar after each one (instead of create. Press Close. There are now several vectors in the 2D View. Vectors are removed by selecting them individually, using the left mouse button or by picking a group and then pressing delete on the keyboard or the cut icon in the assistant. Stretch a box completely over all of the vectors so they turn pink. This means they are selected, Select Cut From the File area of the Assistant. has an Undo facility, which will allow the user to go back 20 steps with Vectors and back one step with a relief.

4 MP3 Casing Example Now that all the original vectors are removed, the same model (Size and Resolution) will be used for the creation of the Vectors required for an IPod Mp3 player casing. Below is a drawing of the item including basic dimensions, so that the user can get an idea of how the final product should look before working through the step by step instructions

5 Select the Create Rectangle icon. Click on the option rectangle. Enter a Width of 60; a Height of 110; Corner Radii of 3 and a centre point of X 0 and Y 0. Press Create. The main shape of the casing is generated Change the Width to 50, Height to 40, Corner Radii to 1 and the centre point to X = 0 and Y = 30. Press the right mouse button. By pressing the right mouse button, the rectangular vector is generated and the Rectangle Assistant page is closed. The second rectangle will represent the screen. Click on the Circle icon. The Circle Creation form appears in the Assistant.

6 Set the Circle centre as X 0 Y 20, Radius as 25 and press Create. Change the Circle radius to 10, and press Create and then Close. This will create the two circles of the Control Panel Now you are going to create the FF icon use the Zoom tool to zoom in on the right hand side of the circles Select the Create Polygons icon Enter No of Sides 3; Angle 90; Centre of Polygon at X = 16, Y = -20 and Radius of 2 Click Create - this will create the first triangle Keep the same values except for the X value change this to 19 Click Create > Close this will create the second triangle.

7 Your FF icon should now look like this The simplest way to create the Rewind icon is to use the Mirror tool to copy the FF icon you have just drawn. Use the Select Vectors to draw a box around the FF icon it should turn pink Choose the Mirror Vectors icon Choose the Right icon - > Close Now use the Select Vectors tool to pick up the copy and move it across to the left side of the circle

8 The next task is to insert the MENU icon at the top of the control panel. Select the icon Vector Text. Note: Any additional fonts loaded onto the computer will be recognised, as well as the standard fonts. Save the model as MP3 player. Close the model. Select Font as Arial, Script Western, Size as 2 mm. Click at the top of the control and type MENU. Text Spacing allows the user to vary the spacing between the individual characters. Select Done. Task : Open a new model of height 150, width 100. Generate the vectors for this apple juice model, using your own values. Save the model as apple.

9

Tutorial 3: Constructive Editing (2D-CAD)

Tutorial 3: Constructive Editing (2D-CAD) (2D-CAD) The editing done up to now is not much different from the normal drawing board techniques. This section deals with commands to copy items we have already drawn, to move them and to make multiple

More information

Paint/Draw Tools. Foreground color. Free-form select. Select. Eraser/Color Eraser. Fill Color. Color Picker. Magnify. Pencil. Brush.

Paint/Draw Tools. Foreground color. Free-form select. Select. Eraser/Color Eraser. Fill Color. Color Picker. Magnify. Pencil. Brush. Paint/Draw Tools There are two types of draw programs. Bitmap (Paint) Uses pixels mapped to a grid More suitable for photo-realistic images Not easily scalable loses sharpness if resized File sizes are

More information

Paint Tutorial (Project #14a)

Paint Tutorial (Project #14a) Paint Tutorial (Project #14a) In order to learn all there is to know about this drawing program, go through the Microsoft Tutorial (below). (Do not save this to your folder.) Practice using the different

More information

Drawing Tools. Drawing a Rectangle

Drawing Tools. Drawing a Rectangle Chapter Microsoft Word provides extensive DRAWING TOOLS that allow you to enhance the appearance of your documents. You can use these tools to assist in the creation of detailed publications, newsletters,

More information

StickFont Editor v1.01 User Manual. Copyright 2012 NCPlot Software LLC

StickFont Editor v1.01 User Manual. Copyright 2012 NCPlot Software LLC StickFont Editor v1.01 User Manual Copyright 2012 NCPlot Software LLC StickFont Editor Manual Table of Contents Welcome... 1 Registering StickFont Editor... 3 Getting Started... 5 Getting Started...

More information

Build a flying buttress of Chartres Cathedral

Build a flying buttress of Chartres Cathedral Build a flying buttress of Chartres Cathedral Overview: Step 1. Create a new Design Layer Step 2. Measure reference image Step 3. Build the buttress Step 4. Build the arches Dimensions for the buttress

More information

TYPE EDIT V12. Tutorial 03. Multicopy to create a set of medals COPYRIGHT 2014 GRAVOTECH MARKING SAS ALL RIGHTS RESERVED

TYPE EDIT V12. Tutorial 03. Multicopy to create a set of medals COPYRIGHT 2014 GRAVOTECH MARKING SAS ALL RIGHTS RESERVED TYPE EDIT V12 Multicopy to create a set of medals COPYRIGHT 2014 GRAVOTECH MARKING SAS ALL RIGHTS RESERVED Multicopy to create a set of medals Creation Time : 45 minutes Level : Intermediate Module : TypeEdit

More information

BASICS OF MOTIONSTUDIO

BASICS OF MOTIONSTUDIO EXPERIMENT NO: 1 BASICS OF MOTIONSTUDIO User Interface MotionStudio combines draw, paint and animation in one easy easy-to-use program gram to save time and make work easy. Main Window Main Window is the

More information

Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013

Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013 SketchUp Level of Difficulty Time Approximately 15 20 minutes Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013

More information

A Comprehensive Introduction to SolidWorks 2011

A Comprehensive Introduction to SolidWorks 2011 A Comprehensive Introduction to SolidWorks 2011 Godfrey Onwubolu, Ph.D. SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Chapter 2 Geometric Construction Tools Objectives: When

More information

User Manual Version 1.1 January 2015

User Manual Version 1.1 January 2015 User Manual Version 1.1 January 2015 - 2 / 112 - V1.1 Variegator... 7 Variegator Features... 7 1. Variable elements... 7 2. Static elements... 7 3. Element Manipulation... 7 4. Document Formats... 7 5.

More information

Trace Bitmap. Chapter 7. A. Page Size. Step 1. Click File Menu > New (Ctrl-N).

Trace Bitmap. Chapter 7. A. Page Size. Step 1. Click File Menu > New (Ctrl-N). Chapter 7 Trace Bitmap Riverview Rams Sarasota High Booker High A. Page Size. Step 1. Click File Menu > New (Ctrl-N). Step 2. Set page size in the Property bar: Width to 3.2 Fig. 1 Height to 2 Step 3.

More information

1. Create a map of the layer and attribute that needs to be queried

1. Create a map of the layer and attribute that needs to be queried Single Layer Query 1. Create a map of the layer and attribute that needs to be queried 2. Choose the desired Select Type. This can be changed from the Map menu at the far top or from the Select Type Icon

More information

Microsoft Visio Working with Shapes

Microsoft Visio Working with Shapes Working with Visio Shapes Shape is the general term for the objects you will find on a stencil and objects created using the drawing tools. These include geometric shapes such as rectangles, triangles

More information

Tutorial VCarving Christmas Decorations

Tutorial VCarving Christmas Decorations Getting Started With Tutorial VCarving Christmas Decorations VCarve Pro Disclaimer All CNC machines (routing, engraving, and milling) are potentially dangerous and because Vectric Ltd has no control over

More information

A Study of Angles & Curves

A Study of Angles & Curves A Study of Angles & Curves Method 1: Cutting Quilt Shapes/Using the Shapes Tools Open BERNINA CutWork Software. Make sure that Create New is selected. Click Next. Place a dot in front of New Graphic. Select

More information

DinoCapture Additional Software Instructions for Measurement models

DinoCapture Additional Software Instructions for Measurement models DinoCapture Additional Software Instructions for Measurement models Window tools Microtouch: The microtouch is a touch sensitive area on the dome that connects to the USB Cable. It functions as a button

More information

Press the Plus + key to zoom in. Press the Minus - key to zoom out. Scroll the mouse wheel away from you to zoom in; towards you to zoom out.

Press the Plus + key to zoom in. Press the Minus - key to zoom out. Scroll the mouse wheel away from you to zoom in; towards you to zoom out. Navigate Around the Map Interactive maps provide many choices for displaying information, searching for more details, and moving around the map. Most navigation uses the mouse, but at times you may also

More information

Adobe Illustrator CC 2018 Tutorial

Adobe Illustrator CC 2018 Tutorial Adobe Illustrator CC 2018 Tutorial GETTING STARTED Adobe Illustrator CC is an illustration program that can be used for print, multimedia and online graphics. Whether you plan to design or illustrate multimedia

More information

Let s Make a Front Panel using FrontCAD

Let s Make a Front Panel using FrontCAD Let s Make a Front Panel using FrontCAD By Jim Patchell FrontCad is meant to be a simple, easy to use CAD program for creating front panel designs and artwork. It is a free, open source program, with the

More information

Quick Crash Scene Tutorial

Quick Crash Scene Tutorial Quick Crash Scene Tutorial With Crash Zone or Crime Zone, even new users can create a quick crash scene diagram in less than 10 minutes! In this tutorial we ll show how to use Crash Zone s unique features

More information

VHSE - COMPUTERISED OFFICE MANAGEMENT MODULE III - Communication and Publishing Art - PageMaker

VHSE - COMPUTERISED OFFICE MANAGEMENT MODULE III - Communication and Publishing Art - PageMaker INTRODUCTION : It is one Adobe PageMaker 7.0 software is the ideal page layout program for business, education, and small- and home-office professionals who want to create high-quality publications such

More information

The Rectangular Problem

The Rectangular Problem C h a p t e r 2 The Rectangular Problem In this chapter, you will cover the following to World Class standards: The tools for simple 2D Computer Aided Drafting (CAD) The Command Line and the Tray The Line

More information

Laser Machine User Manual:

Laser Machine User Manual: Laser Machine User Manual: OPERATOR ( EasyCut / LaserCut version 5.3 ) v1.0 CTR Laser Machine Operator Manual ( EasyCut version 5.3 ) ~ version 1.0 1 CONTENTS Section 1: Tutorials...5 1.1. How to Cut with

More information

An Introduction to GeoGebra

An Introduction to GeoGebra An Introduction to GeoGebra Downloading and Installing Acquiring GeoGebra GeoGebra is an application for exploring and demonstrating Geometry and Algebra. It is an open source application and is freely

More information

GDL Toolbox 2 Reference Manual

GDL Toolbox 2 Reference Manual Reference Manual Archi-data Ltd. Copyright 2002. New Features Reference Manual New Save GDL command Selected GDL Toolbox elements can be exported into simple GDL scripts. During the export process, the

More information

Part 1: Basics. Page Sorter:

Part 1: Basics. Page Sorter: Part 1: Basics Page Sorter: The Page Sorter displays all the pages in an open file as thumbnails and automatically updates as you add content. The page sorter can do the following. Display Pages Create

More information

3D Modeler Creating Custom myhouse Symbols

3D Modeler Creating Custom myhouse Symbols 3D Modeler Creating Custom myhouse Symbols myhouse includes a large number of predrawn symbols. For most designs and floorplans, these should be sufficient. For plans that require that special table, bed,

More information

3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD

3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD 3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions

More information

Battery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1

Battery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1 Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.

More information

Minimal AutoCAD 2011

Minimal AutoCAD 2011 PDHonline Course G371 (2 PDH) Minimal AutoCAD 2011 Instructor: Thomas Mason, P.E. 2012 PDH Online PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658 Phone & Fax: 703-988-0088 www.pdhonline.org

More information

2D Design. Window. 3D Window. Toolpat h Operati ons. Navigation Homepage. Layer Managemen t. Component Manager. Modeling Tools

2D Design. Window. 3D Window. Toolpat h Operati ons. Navigation Homepage. Layer Managemen t. Component Manager. Modeling Tools Navigation Homepage Click on the region of the interface you are interested in to navigate to the relevant section of this manual. At the foot of each page is a Navigation Homepage link, click on this

More information

National Weather Map

National Weather Map Weather Map Objectives Each student will utilize the Google Docs drawing application to create a map using common weather map symbols that show the current state of the weather in the United States. Benchmarks

More information

Beginning Paint 3D A Step by Step Tutorial. By Len Nasman

Beginning Paint 3D A Step by Step Tutorial. By Len Nasman A Step by Step Tutorial By Len Nasman Table of Contents Introduction... 3 The Paint 3D User Interface...4 Creating 2D Shapes...5 Drawing Lines with Paint 3D...6 Straight Lines...6 Multi-Point Curves...6

More information

GraphWorX64 Productivity Tips

GraphWorX64 Productivity Tips Description: Overview of the most important productivity tools in GraphWorX64 General Requirement: Basic knowledge of GraphWorX64. Introduction GraphWorX64 has a very powerful development environment in

More information

4. Generating a Relief

4. Generating a Relief ArtCAM Pro 5.5 Relief. The 3D model created by ArtCAM Pro is called a Relief and is shown in the 3D View. The Relief is defined by a resolution in a similar way to a bitmap image. But, instead of each

More information

V-BOX Cloud Configuration

V-BOX Cloud Configuration V-BOX Cloud Configuration Website: http://www.we-con.com.cn/en Technical Support: support@we-con.com.cn Skype: fcwkkj Phone: 86-591-87868869 QQ: 1043098682 Technical forum: http://wecon.freeforums.net/

More information

Autodesk Inventor - Basics Tutorial Exercise 1

Autodesk Inventor - Basics Tutorial Exercise 1 Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be

More information

Tutorial 3 Kitchen Cabinet Door

Tutorial 3 Kitchen Cabinet Door Getting Started With Tutorial 3 Kitchen Cabinet Door VCarve Pro Disclaimer All CNC machines (routing, engraving, and milling) are potentially dangerous and because Vectric Ltd has no control over how

More information

Introduction to AutoCAD 2010

Introduction to AutoCAD 2010 Introduction to AutoCAD 2010 Alf Yarwood Chapter 3 Exercise 1 1. Open AutoCAD 2010 with a double-click on its shortcut icon in the Windows desktop. 2. Call the Line tool with a left-click on its tool icon

More information

Corel Draw 11. What is Vector Graphics?

Corel Draw 11. What is Vector Graphics? Corel Draw 11 Corel Draw is a vector based drawing that program that makes it easy to create professional artwork from logos to intricate technical illustrations. Corel Draw 11's enhanced text handling

More information

Draw Guide. Chapter 2 Drawing Basic Shapes

Draw Guide. Chapter 2 Drawing Basic Shapes Draw Guide Chapter 2 Drawing Basic Shapes Copyright This document is Copyright 2005 2011 by its contributors as listed below. You may distribute it and/or modify it under the terms of either the GNU General

More information

Guide to WB Annotations

Guide to WB Annotations Guide to WB Annotations 04 May 2016 Annotations are a powerful new feature added to Workbench v1.2.0 (Released May 2016) for placing text and symbols within wb_view tabs and windows. They enable generation

More information

7/21/2009. Chapters Learning Objectives. Fillet Tool

7/21/2009. Chapters Learning Objectives. Fillet Tool Chapters 12-13 JULY 21, 2009 Learning Objectives Chapter 12 Chapter 13 Use the FILLET tool to draw fillets, rounds, and other rounded corners. Place chamfers and angled corners with the CHAMFER tool. Separate

More information

Insight: Measurement Tool. User Guide

Insight: Measurement Tool. User Guide OMERO Beta v2.2: Measurement Tool User Guide - 1 - October 2007 Insight: Measurement Tool User Guide Open Microscopy Environment: http://www.openmicroscopy.org OMERO Beta v2.2: Measurement Tool User Guide

More information

2 Solutions Chapter 3. Chapter 3: Practice Example 1

2 Solutions Chapter 3. Chapter 3: Practice Example 1 1 Solutions This section includes the step by step solutions for the practice exercise for the following chapters and sections: Chapter 3 Chapter 4 Chapter 5 Chapter 11: Rainbow Springs sample test Final

More information

Tutorial 1 Engraved Brass Plate R

Tutorial 1 Engraved Brass Plate R Getting Started With Tutorial 1 Engraved Brass Plate R4-090123 Table of Contents What is V-Carving?... 2 What the software allows you to do... 3 What file formats can be used?... 3 Getting Help... 3 Overview

More information

Draw Guide. Chapter 2 Drawing Basic Shapes

Draw Guide. Chapter 2 Drawing Basic Shapes Draw Guide Chapter 2 Drawing Basic Shapes Copyright This document is Copyright 2005 2012 by its contributors as listed below. You may distribute it and/or modify it under the terms of either the GNU General

More information

1 General Principles. General Principles. In this chapter 1-1

1 General Principles. General Principles. In this chapter 1-1 1 General Principles In this chapter 1 General Principles 1.1 User Interface 1.2 Title bar 1.3 Menu bar 1.4 Standard Toolbar 1.5 The drawing area 1.6 Component tabs 1.7 Status Bar 1.8 Manipulating Components

More information

City of La Crosse Online Mapping Website Help Document

City of La Crosse Online Mapping Website Help Document City of La Crosse Online Mapping Website Help Document This document was created to assist in using the new City of La Crosse online mapping sites. When the website is first opened, a map showing the City

More information

Designer Reference 1

Designer Reference 1 Designer Reference 1 Table of Contents USE OF THE DESIGNER...4 KEYBOARD SHORTCUTS...5 Shortcuts...5 Keyboard Hints...5 MENUS...7 File Menu...7 Edit Menu...8 Favorites Menu...9 Document Menu...10 Item Menu...12

More information

Technique or Feature Where Introduced

Technique or Feature Where Introduced Part 6: Keypad 4 Mirrored features Patterned features First extrusion Rounded corners In the earpiece part, you defined a radial pattern, one that created new instances of a feature at intervals around

More information

USER S MANUAL Software Usage Agreement Registered Trademarks Notes on this Manual Disclaimer

USER S MANUAL Software Usage Agreement Registered Trademarks Notes on this Manual Disclaimer USER S MANUAL Software Usage Agreement Registered Trademarks Notes on this Manual Disclaimer 1 1.1 1.2 2 3 Introduction 2.1 2.2 Features System Requirements Installing Xyron Wishblade Software 3.1 3.2

More information

Using SymPrint to Make Overlays, Templates & More...

Using SymPrint to Make Overlays, Templates & More... Welcome to SymPrint SymPrint is an easy-to-use tool for creating communication overlays, worksheets, classroom activities and more using a modern toolbar and common-sense interface modeled after the programs

More information

Motic Images Plus 3.0 ML Software. Windows OS User Manual

Motic Images Plus 3.0 ML Software. Windows OS User Manual Motic Images Plus 3.0 ML Software Windows OS User Manual Motic Images Plus 3.0 ML Software Windows OS User Manual CONTENTS (Linked) Introduction 05 Menus and tools 05 File 06 New 06 Open 07 Save 07 Save

More information

SketchUp Starting Up The first thing you must do is select a template.

SketchUp Starting Up The first thing you must do is select a template. SketchUp Starting Up The first thing you must do is select a template. While there are many different ones to choose from the only real difference in them is that some have a coloured floor and a horizon

More information

to display both cabinets. You screen should now appear as follows:

to display both cabinets. You screen should now appear as follows: Technical Support Bulletin: AllenCAD Tutorial Last Updated November 12, 2005 Abstract: This tutorial demonstrates most of the features of AllenCAD necessary to design or modify a countertop using the program.

More information

- Is the process of combining texts and graphics layout to produce publications e.g. cards,

- Is the process of combining texts and graphics layout to produce publications e.g. cards, DESKTOP PUBLISHING (DTP) - Is the process of combining texts and graphics layout to produce publications e.g. cards, newspapers, catalogues etc. - A special DTP software is always used. PURPOSE OF DTP

More information

3ds Max Cottage Step 1. Always start out by setting up units: We re going with this setup as we will round everything off to one inch.

3ds Max Cottage Step 1. Always start out by setting up units: We re going with this setup as we will round everything off to one inch. 3ds Max Cottage Step 1 Always start out by setting up units: We re going with this setup as we will round everything off to one inch. File/Import the CAD drawing Be sure Files of Type is set to all formats

More information

ADOBE TRAINING CS6 PHOTOSHOP BASICS: EDITING PHOTOS & WORKING WITH TEXT - 1

ADOBE TRAINING CS6 PHOTOSHOP BASICS: EDITING PHOTOS & WORKING WITH TEXT - 1 ADOBE TRAINING CS6 PHOTOSHOP BASICS: EDITING PHOTOS & WORKING WITH TEXT Photoshop is the leading professional software for editing and adjusting photos, images and other graphic projects. It is a very

More information

The Villa Savoye ( ), Poisy, Paris.

The Villa Savoye ( ), Poisy, Paris. Learning SketchUp Villa Savoye This tutorial will involve modeling the Villa Savoye by Le Corbusier Files needed to complete this tutorial are available in Mr. Cochran s Web Site The Villa Savoye (1929-1931),

More information

Lesson 1: Creating T- Spline Forms. In Samples section of your Data Panel, browse to: Fusion 101 Training > 03 Sculpt > 03_Sculpting_Introduction.

Lesson 1: Creating T- Spline Forms. In Samples section of your Data Panel, browse to: Fusion 101 Training > 03 Sculpt > 03_Sculpting_Introduction. 3.1: Sculpting Sculpting in Fusion 360 allows for the intuitive freeform creation of organic solid bodies and surfaces by leveraging the T- Splines technology. In the Sculpt Workspace, you can rapidly

More information

Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013

Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013 SketchUp Level of Difficulty Time Approximately 15 20 minutes Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013

More information

creating files and saving for web

creating files and saving for web creating files and saving for web the template files assume a default image size of 300 x 300 pixels images intended for the web should be produced in rgb mode name your images in a logical format, so

More information

Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment

Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment ANSYS Workbench Tutorial Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS

More information

March 2006, rev 1.3. User manual

March 2006, rev 1.3. User manual March 2006, rev 1.3 User manual Note concerning the warranty and the rights of ownership The information contained in this document is subject to modification without notice. The vendor and the authors

More information

Creating a 3D bottle with a label in Adobe Illustrator CS6.

Creating a 3D bottle with a label in Adobe Illustrator CS6. Creating a 3D bottle with a label in Adobe Illustrator CS6. Step 1 Click on File and then New to begin a new document. Step 2 Set up the width and height of the new document so that there is enough room

More information

Contents escope Software Guide Execute Software Calibration and Measurement escope Software Interface Instructions Main Interface

Contents escope Software Guide Execute Software Calibration and Measurement escope Software Interface Instructions Main Interface Contents escope Software Guide Execute Software...3 Capture Photo...3 Capture Video...3 Time-lapsed Picture / Video...4 Picture / Video Save as...4 Calibration and Measurement Calibration...5 Measurement...7

More information

file://c:\dokumente und Einstellungen\Lot\Lokale Einstellungen\Temp\~hhD434.htm

file://c:\dokumente und Einstellungen\Lot\Lokale Einstellungen\Temp\~hhD434.htm Seite 1 von 56 Welcome to splan 7.0 splan is an easy-to-handle and comfortable CAD-software, developed for electronic and electric circuit diagrams. Dragging and dropping components from the library to

More information

Creating a Text Frame. Create a Table and Type Text. Pointer Tool Text Tool Table Tool Word Art Tool

Creating a Text Frame. Create a Table and Type Text. Pointer Tool Text Tool Table Tool Word Art Tool Pointer Tool Text Tool Table Tool Word Art Tool Picture Tool Clipart Tool Creating a Text Frame Select the Text Tool with the Pointer Tool. Position the mouse pointer where you want one corner of the text

More information

Create a unit using United Streaming and PowerPoint. Materials: Microsoft PowerPoint, Internet access, United Streaming account

Create a unit using United Streaming and PowerPoint. Materials: Microsoft PowerPoint, Internet access, United Streaming account Create a unit using United Streaming and PowerPoint Materials: Microsoft PowerPoint, Internet access, United Streaming account Find United Streaming Clips: 1. Decide on a topic for your unit. 2. Search

More information

OrthoWin ShapeDesigner Manual V OrthoWin ShapeDesigner Software Manual

OrthoWin ShapeDesigner Manual V OrthoWin ShapeDesigner Software Manual OrthoWin ShapeDesigner Software Manual ORTHEMA Page 1 of 21 Content 1 Introduction...3 2 Menu prompting...3 3 Main window...4 4 File menu...5 4.1 New and Open...5 4.2 Save and Save As...5 4.3 Export to

More information

Chapter 5 Managing Graphic Objects

Chapter 5 Managing Graphic Objects Impress Guide Chapter 5 Managing Graphic Objects Moving, rotating, distorting, and positioning objects; animations; Fontwork This PDF is designed to be read onscreen, two pages at a time. If you want to

More information

Dolphin PartMaster Wire EDM

Dolphin PartMaster Wire EDM Dolphin PartMaster Wire EDM Copyright 2000-2017 Dolphin CADCAM Systems Ltd. This document is copyrighted and all rights are reserved. This document may not, in whole or in part, be copied or reproduced

More information

How to create shapes. Drawing basic shapes. Adobe Photoshop Elements 8 guide

How to create shapes. Drawing basic shapes. Adobe Photoshop Elements 8 guide How to create shapes With the shape tools in Adobe Photoshop Elements, you can draw perfect geometric shapes, regardless of your artistic ability or illustration experience. The first step to drawing shapes

More information

Introduction To Inkscape Creating Custom Graphics For Websites, Displays & Lessons

Introduction To Inkscape Creating Custom Graphics For Websites, Displays & Lessons Introduction To Inkscape Creating Custom Graphics For Websites, Displays & Lessons The Inkscape Program Inkscape is a free, but very powerful vector graphics program. Available for all computer formats

More information

Undo Button Clicking this tool will undo the last action. Clicking on this tool multiple times will undo all subsequent changes that were made.

Undo Button Clicking this tool will undo the last action. Clicking on this tool multiple times will undo all subsequent changes that were made. SMS Featured Icons: Editor Window This document includes a brief description of the tools in the SMS Desktop Software Editor windows, as well as showing you the toolbar shortcuts to easily access these

More information

SketchUp. SketchUp. Google SketchUp. Using SketchUp. The Tool Set

SketchUp. SketchUp. Google SketchUp. Using SketchUp. The Tool Set Google Google is a 3D Modelling program which specialises in making computer generated representations of real-world objects, especially architectural, mechanical and building components, such as windows,

More information

ROBO Master OPS656. USER'S MANUAL MANUAL NO. OPS656m-UM Introduction 1.1 Features System Requirements... 3

ROBO Master OPS656. USER'S MANUAL MANUAL NO. OPS656m-UM Introduction 1.1 Features System Requirements... 3 USER'S MANUAL MANUAL NO. m-um-152 Software Usage Agreement... 2 Registered Trademarks... 2 Notes on this Manual... 2 Disclaimer... 2 1 Introduction 1.1 Features... 3 1.2 System Requirements... 3 2 Installing

More information

Webtorial: 2-Point Tracking

Webtorial: 2-Point Tracking This webtorial will show you how to use 2-point tracking to attach a missing arrowhead to its clock hand and track the hand s movement to ensure that the arrowhead stays on its hand as it rotates. You

More information

Acknowledgement INTRODUCTION

Acknowledgement INTRODUCTION Submitted by: 1 Acknowledgement INTRODUCTION Computers are increasingly being used for doing engineering drawings and graphics work because computers allow the graphics designer or the draughtsman to change

More information

Module 1: Basics of Solids Modeling with SolidWorks

Module 1: Basics of Solids Modeling with SolidWorks Module 1: Basics of Solids Modeling with SolidWorks Introduction SolidWorks is the state of the art in computer-aided design (CAD). SolidWorks represents an object in a virtual environment just as it exists

More information

Code Finix Label Designer V 1.0 User Guide

Code Finix Label Designer V 1.0 User Guide Code Finix Label Designer V 1.0 User Guide Introduction Welcome, Code Finix Label Designer is a family of professional labeling software products that brings a complete barcode printing solution for desktop

More information

Ai Adobe. Illustrator. Creative Cloud Beginner

Ai Adobe. Illustrator. Creative Cloud Beginner Ai Adobe Illustrator Creative Cloud Beginner Vector and pixel images There are two kinds of images: vector and pixel based images. A vector is a drawn line that can be filled with a color, pattern or gradient.

More information

SOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering

SOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now

More information

Toolbar. Actions Panel. Plug-Ins Panel. Tools Panel

Toolbar. Actions Panel. Plug-Ins Panel. Tools Panel Toolbar The Toolbar enables user to select and work with a variety of tools. The buttons on the toolbar are organized in panels: Actions Panel Buttons provide user to make changes to.notebook files Plug-Ins

More information

2D & 3D CAD SOFTWARE USER MANUAL. AutoQ3D CAD for ipad & iphone

2D & 3D CAD SOFTWARE USER MANUAL. AutoQ3D CAD for ipad & iphone Type to enter text 2D & 3D CAD SOFTWARE USER MANUAL AutoQ3D CAD for ipad & iphone AUTOQ3D TEAM FIRST EDITION AutoQ3D CAD for ipad & iphone 2D / 3D cad software user manual 2015 by AutoQ3D Team. All rights

More information

FactoryLink 7. Version 7.0. Client Builder Reference Manual

FactoryLink 7. Version 7.0. Client Builder Reference Manual FactoryLink 7 Version 7.0 Client Builder Reference Manual Copyright 2000 United States Data Corporation. All rights reserved. NOTICE: The information contained in this document (and other media provided

More information

Creating T-Spline Forms

Creating T-Spline Forms 1 / 28 Goals 1. Create a T-Spline Primitive Form 2. Create a T-Spline Revolve Form 3. Create a T-Spline Sweep Form 4. Create a T-Spline Loft Form 2 / 28 Instructions Step 1: Go to the Sculpt workspace

More information

Exercise Guide. Published: August MecSoft Corpotation

Exercise Guide. Published: August MecSoft Corpotation VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4

More information

BDM s Annotation User Guide

BDM s Annotation User Guide ETS :Foothill De Anza CC District April 17, 2014 1 BDM s Annotation User Guide Users with Read/Write access can annotate (markup) documents if they retrieve the document using Microsoft s Internet Explorer

More information

Module 5: Creating Sheet Metal Transition Piece Between a Square Tube and a Rectangular Tube with Triangulation

Module 5: Creating Sheet Metal Transition Piece Between a Square Tube and a Rectangular Tube with Triangulation 1 Module 5: Creating Sheet Metal Transition Piece Between a Square Tube and a Rectangular Tube with Triangulation In Module 5, we will learn how to create a 3D folded model of a sheet metal transition

More information

Exploring Translations

Exploring Translations Exploring Translations 1. New Sketch: To open a new sketch go to FILE and click on New Sketch 2. Create a triangle. a. Using the SEGMENT tool, construct a triangle. b. Drag the cursor and release for each

More information

ATNS. USING Google EARTH. Version 1

ATNS. USING Google EARTH. Version 1 ATNS USING Google EARTH Version 1 ATNS/HO/Using Google Earth Page 1 25/04/2013 CONTENTS 1. BASIC SETUP 2. NAVIGATING IN GOOGLE EARTH 3. ADDING OBJECTS TO GOOGLE EARTH 4. USER HELP REFERENCES ATNS/HO/Using

More information

Chapter 5. Inserting Objects. Highlights

Chapter 5. Inserting Objects. Highlights Chapter 5 Inserting Objects Highlights 5. Inserting AutoShapes, WordArts and ClipArts 5. Changing Object Position, Size and Colour 5. Drawing Lines 5.4 Inserting Pictures and Text Boxes 5.5 Inserting Movies

More information

Input CAD Solid Model Assemblies - Split into separate Part Files. DXF, IGES WMF, EMF STL, VDA, Rhino Parasolid, ACIS

Input CAD Solid Model Assemblies - Split into separate Part Files. DXF, IGES WMF, EMF STL, VDA, Rhino Parasolid, ACIS General NC File Output List NC Code Post Processor Selection Printer/Plotter Output Insert Existing Drawing File Input NC Code as Geometry or Tool Paths Input Raster Image Files Report Creator and Designer

More information

Sending image(s) to report Click Send Snapshot on any screen in Dolphin3D and choose the Send to Report option

Sending image(s) to report Click Send Snapshot on any screen in Dolphin3D and choose the Send to Report option Dolphin 3D Reports Sending image(s) to report Click Send Snapshot on any screen in Dolphin3D and choose the Send to Report option Creating a report step by step 1. Generate the desired images in Dolphin3D

More information

Getting Started. Moving Around in 3D

Getting Started. Moving Around in 3D Getting Started 1 Double-click the SketchUp icon or click: Start All Programs SketchUp 2018 SketchUp 2018 The start screen should look something like this: This person is about 5 5 tall this sets the scale

More information

Getting Started. Double-click the SketchUp icon or click: Start All Programs SketchUp 2018 SketchUp 2018

Getting Started. Double-click the SketchUp icon or click: Start All Programs SketchUp 2018 SketchUp 2018 Getting Started 1 Double-click the SketchUp icon or click: Start All Programs SketchUp 2018 SketchUp 2018 The start screen should look something like this: This person is about 5 5 tall this sets the scale

More information

PLAY VIDEO. Fences can be any shape from a simple rectangle to a multisided polygon, even a circle.

PLAY VIDEO. Fences can be any shape from a simple rectangle to a multisided polygon, even a circle. Chapter Eight Groups PLAY VIDEO INTRODUCTION There will be times when you need to perform the same operation on several elements. Although this can be done by repeating the operation for each individual

More information