CNC MILLING MACHINE NER VC180)

Size: px
Start display at page:

Download "CNC MILLING MACHINE NER VC180)"

Transcription

1 CNC MILLING MACHINE (SPINNER NER VC180) PREPARED BY: RAFIZAH BINTI ABDUL RASHID NOR ZAIAZMIN BIN YAHAYA PREPARED FOR: ADVANCED MANUFACTURING TECHNOLOGY (EPT 311) Page 1 of 12

2 TURNING ON THE CNC MILLING MACHINE 1 Before using CNC Milling machine, make sure the air compressor is switched ON. 1 2 Turn ON the main power [Anti Clockwise]. 2 3 Press the ON button at the CNC Milling machine once. Make sure the EMERGENCY BUTTON is released Wait until the screen (as shown in 6) appear. Then, OPEN AND CLOSE THE DOOR. 6 Page 2 of 12

3 5 5 Button? MC will show a yellow alarm. Press the button and read the message. The Message: 7 WAITING FOR SIGNAL SERVO READY START AXIS START MCC OFF Press RESET, then press SERVO BUTTON (refer 8) 8 until you heard a sound. Press the SERVO BUTTON again. 8 Note: Press RESET button if there is any alarm/error. 6 Now, you can start using this CNC Milling machine. 9 MOVING THE AXIS MANUALLY 1 First, press HANDLE MULTIPLY button (X 1, X 10, X 100, or X 1000), then press the button Press the one of the HANDLE AXIS you want to move. Note: If you want to move X-Axis, press the X Button. 11 Page 3 of 12

4 3 Turn the handle. Note: Clockwise for positive increment and Anti Clockwise for negative increment. 12 USING MDI OPTION 1 Press MDI button at MODE SELECT button Then press PROG button (if necessary), at PROGRAM PANEL BUTTON and the screen as shown below will appear Then key in the command. Example (refer figure 16): To turn on the spindle, key in M03 S1000; To change the cutter, key in M06 T07; 16 4 Press CYCLE START button. 17 Page 4 of 12

5 KEY IN PART PROGRAMMING MANUALLY 1 Press EDIT button at MODE SELECT button Then press PROG button (if necessary), at PROGRAM PANEL button. 3 Press DIR at SOFTKEY button Check a program name that has not been used yet Key in a new program name, example O8005, press INSERT ** All the program name need to start with letter O. 5 Key in the part program using PROGRAM PANEL BUTTON. EOB means End of Block and the symbol of ; represent the EOB. CAN has the same function with BACKSPACE button at computer keyboard. SHIFT also has the same function with SHIFT button at computer keyboard. ALTER is used if you want to make an alteration, by moving the up and down and left and right cursor. DELETE is used if you want to delete, by moving the up and down and left and right cursor also. INSERT has the same function with ENTER button at computer keyboard. 20 Example: ;G40 ; Press,,,, and. Important!!! Make sure to put point at each coordinate number. 21 Page 5 of 12

6 UPLOAD PROGRAMMING FROM SERVER 1 At Mode Select, push the Edit Button 22 2 Push the Program button [PROG] and press [+] at the screen button 23 3 Push the [oprt] than [+] than [read] and finally [exec] button. 4 Open the CIMCO DNC software at the CNC Server Computer 5 Change the Communication Port to COM3 6 Click the Send button and select the NC file SIMULATION 1 Important!!! After finish key in the program, it is advisable to run the simulation first, before running the actual machining. Press GRAPH button until the screen appear (refer 30). Press twice if necessary Press AUTO at MODE SELECT Press SIMLAT at the SOFT KEY button, then press TLPATH and START If the part program run by the simulation has any error, made the correction until there is no errors Page 6 of 12

7 appear. SETTING TING UP AN ORIGIN TO THE WORKPIECE (COORDINATE SETTING) 1 Press PROG button at PROGRAM PANEL BUTTON. (Press twice if necessary) 2 Before setting the origin, you need to clamp your workpiece at the machine. Turn on the spindle manually using Manual Data Input (MDI) Refer page USING MDI OPTION 25 3 Then touch the rotating spindle to the workpiece, and set either X, Y or Z origin. X-Origin Y-Origin Z-Origin 26 4 How to set the origin at the machine? Press POS button at PROGRAM PANEL BUTTON, and REL at SOFT KEY button Press X, Y or Z at the PROGRAM PANEL BUTTON. Then Press Origin (refer figure 32) at the SOFT KEY button 27 Page 7 of 12

8 5 Press OFFSET SETTING button at PROGRAM PANEL BUTTON. Press WORK at SOFT KEY button (if necessary) Press ALL at SOFT KEY button if necessary (to show all the coordinate) Key in X and Y value of the machine coordinates to WORK COORDINATES ATES column and press INPUT. Press RESET and the Absolute coordinates will show X: 0.0 Y: Important!! If you state G54 as the work coordinate in your program, so key in the machine point at the G54 column [Make sure the Relative coordinate is showed the X0.0, Y0.0 and Z0.0, then you can take the Machine coordinate and put into the WORK COORDINATE column] Press OFFSET SETTING button at PROGRAM PANEL BUTTON. Key in Z-value of the machine coordinates to length (geometry) column and press INPUT. Key in the radius of cutter at radius (geometry) column and press INPUT. ** (The number of column is regarding to your tool number.) Important!! [The radius of cutter is important when you want to use cutter compensation command, G41 or G42.] 30 RUNNING NING THE PART PROGRAM 1 If the part program from the simulation runs smoothly, now you can start the real machining. (Important: Make sure you have done the coordinate setting properly.) Press PROG (if necessary), then press AUTO at MODE SELECT and press RESET button. Page 8 of 12

9 31 32 Turn the FEED OVERIDE to ZERO%. Press CYCLE START. Turn the FEED OVERIDE slowly first until you confirm the program will run safely before turn to 100% movement of the feed. Page 9 of 12

10 LAB 3 CNC MILLING Lab Report GROUP NUMBER : DATE OF EXPERIMENT : GROUP MEMBERS NAME : 1) signature: 2) signature: 3) signature: 4) signature: 5) signature: Page 10 of 12

11 DISCUSSION 1. State five (5) disadvantages of CNC over conventional machining. (5 marks) 2. Write the procedure in your own words how to set the work piece before you start the CNC Milling process. (5 marks) Page 11 of 12

12 3. Give at least 1 recommendation to improve the setting of the work piece for CNC Milling. (2 marks) 4. What are the commands / procedures for the CNC Milling to begin receiving file from CIMCO DNC software? (3 marks) 5. Why you need to setup work piece offset and tool offset setting before running the CNC program? (5 marks) MARKS: / 20 Marks Page 12 of 12

GE FANUC 21 CONCEPT 55 MILL ATC TEACHER GUIDE

GE FANUC 21 CONCEPT 55 MILL ATC TEACHER GUIDE GE FANUC 21 CONCEPT 55 MILL ATC TEACHER GUIDE 11/1/07 Version 2 Made by EMCO Authored by Chad Hawk Training Index Control Keyboard Pg 1 Fanuc 21 Control Machine Control Fanuc 21 Screen. Pg 2 Fanuc 21 Keys.

More information

Lesson 6 The Key Operation Procedures

Lesson 6 The Key Operation Procedures Lesson 6 The Key Operation Procedures Step-by-step procedures can keep you from having to memorize every function that you must perform on your CNC machining center. You will soon memorize procedures for

More information

GE FANUC 21 CONCEPT 55 TURN TEACHER GUIDE

GE FANUC 21 CONCEPT 55 TURN TEACHER GUIDE GE FANUC 21 CONCEPT 55 TURN TEACHER GUIDE 2/13/08 Version 2 Made by EMCO Authored by Chad Hawk Training Index Control Keyboard Pg 1 Fanuc 21 Control Machine Control Fanuc 21 Screen Pg 2 Fanuc 21 Keys Pg

More information

IEEM 215. Manufacturing Processes I Introduction to the ARIX CNC milling machine

IEEM 215. Manufacturing Processes I Introduction to the ARIX CNC milling machine IEEM 215. Manufacturing Processes I Introduction to the ARIX CNC milling machine The image below is our ARIX Milling machine. The machine is controlled by the controller. The control panel has several

More information

Polar coordinate interpolation function G12.1

Polar coordinate interpolation function G12.1 Polar coordinate interpolation function G12.1 On a Turning Center that is equipped with a rotary axis (C-axis), interpolation between the linear axis X and the rotary axis C is possible by use of the G12.1-function.

More information

2. INTRODUCTION TO CNC

2. INTRODUCTION TO CNC Q. Define NC Machines. 2. INTRODUCTION TO CNC A method of automation, in which various functions and processing of machine tools are controlled by letters and symbols. The general objective of NC technology

More information

Operation Manual. V3.3 December, Wuhan Huazhong Numerical Control Co., Ltd

Operation Manual. V3.3 December, Wuhan Huazhong Numerical Control Co., Ltd Century Star Milling CNC System Operation Manual V3.3 December, 2007 Wuhan Huazhong Numerical Control Co., Ltd 2007 Wuhan Huazhong Numerical Control Co., Ltd Preface Preface Organization of documentation

More information

HAAS Mini Mill User s Manual

HAAS Mini Mill User s Manual Using the Haas Mini Mills HAAS Mini Mill User s Manual Stanford Product Realization Laboratory Version 1.3 166 1. Machine (Pre) Start-Up a. Check Oil Reservoir (at rear of machine). If Oil Level is below

More information

Digital display for EMCO milling machines

Digital display for EMCO milling machines Digital display for EMCO milling machines Input box 7 8 9 1 X Y Z HELP 4 5 6 1 2 3 0. - ESC 3 CE ENT R + R - 2 REF RST 1... Screen (working window, displays) 2... 5 soft keys (function depends on the respective

More information

GE Fanuc Automation. Series 16i / 18i / 21i Model TA Manual Guide. Computer Numerical Control Products. Operator's Manual

GE Fanuc Automation. Series 16i / 18i / 21i Model TA Manual Guide. Computer Numerical Control Products. Operator's Manual GE Fanuc Automation Computer Numerical Control Products Series 16i / 18i / 21i Model TA Manual Guide Operator's Manual B-63344EN/01 July 1998 Warnings, Cautions, and Notes as Used in this Publication GFL-001

More information

OKUMA MACHINING CENTER OPERATORS GUIDE OSP P200M THiNC

OKUMA MACHINING CENTER OPERATORS GUIDE OSP P200M THiNC OKUMA MACHINING CENTER OPERATORS GUIDE OSP P200M THiNC OSP P200 Mill Training Rev1 1 OKUMA MACHINING CENTER OPERATORS GUIDE Scope 4 Section 1 Guide to Controls on Operation Panels 5 Section 2 Manual Tool

More information

Welcome to. the workshop on the CNC 8055 MC

Welcome to. the workshop on the CNC 8055 MC Welcome to the workshop on the CNC 8055 MC Sales Dpt-Training: 2009-sept-25 FAGOR CNC 8055MC seminar 1 Sales Dpt-Training: 2009-sept-25 FAGOR CNC 8055MC seminar 2 This manual is part of the course for

More information

SINUMERIK 828D / 840D sl quick reference chart

SINUMERIK 828D / 840D sl quick reference chart SINUMERIK 828D / 840D sl quick reference chart Jog functions 1. Power up with reference procedure (machine-dependent) Initial power up switch the main disconnect switch to on wait for the entire system

More information

dfab Laguna CNC Manual With FANUC Control

dfab Laguna CNC Manual With FANUC Control dfab Laguna CNC Manual With FANUC Control 1 Introduction Throughout this manual we use different nomenclature for [HARD KEYS] and (SOFT KEYS). A [HARD KEY] is a button on the CONTROL PANEL (upper panel)

More information

List of Macro Variables

List of Macro Variables APPENDIX C List of Macro Variables Variable Purpose Page #0 Null variable 22 #1 #33 Local variables 28 #34 #99 Not available 28 #100 #199 Common variables 28 #200 #499 Not available 28 #500 #999 Permanent

More information

ADT-CNC46208 CNC LATHE SYSTEM Maintenance Manual

ADT-CNC46208 CNC LATHE SYSTEM Maintenance Manual ADT-CNC46208 CNC LATHE SYSTEM Maintenance Manual http//www.salecnc.com Email sales@salecnc.com . Contents Contents 1. Foreword... - 3-2. System technical characteristics... - 3-2.1 System structure...-

More information

Xbox gamepad CNC pendant user manual

Xbox gamepad CNC pendant user manual Patrik Tegelberg 2017-09-04 Xbox gamepad CNC pendant user manual Computer controlled manufacturing machines are awesome, and not designed for manual cutting. This controller, for LinuxCNC, maintains the

More information

Lesson 4 Introduction To Programming Words

Lesson 4 Introduction To Programming Words Lesson 4 Introduction To Programming Words All CNC words include a letter address and a numerical value. The letter address identifies the word type. The numerical value (number) specifies the value of

More information

Conversational Programming for 6000i CNC

Conversational Programming for 6000i CNC Conversational Programming for 6000i CNC www.anilam.com P/N 634 755-22 - Contents Section 1 - Introduction Section 2 - Conversational Mode Programming Hot Keys Programming Hot Keys... 2-1 Editing Keys...

More information

3000M CNC Programming and Operations Manual for Two-Axis Systems

3000M CNC Programming and Operations Manual for Two-Axis Systems 3000M CNC Programming and Operations Manual for Two-Axis Systems www.anilam.com P/N 70000496G - Contents Section 1 - CNC Programming Concepts Programs... 1-1 Axis Descriptions... 1-1 X Axis... 1-2 Y Axis...

More information

6 Series Mill Controller Operation Manual

6 Series Mill Controller Operation Manual 6 Series Mill Controller Operation Manual Date: 2013/10/25 Version: 1.1 Contents 1 Function Key and System Configuration... 4 1.1 Main Screen Sections... 4 1.2 CNC System Configuration... 5 1.3 Coordinate...

More information

COMPUTER NUMERICAL CONTROL OF MACHINE TOOLS

COMPUTER NUMERICAL CONTROL OF MACHINE TOOLS COMPUTER NUMERICAL CONTROL OF MACHINE TOOLS Department of Mechanical Engineering and Aeronautics University of Patras, Greece Dr. Dimitris Mourtzis Associate professor Patras, 2017 1/52 Chapter 8: Two

More information

Prof. Steven S. Saliterman Introductory Medical Device Prototyping

Prof. Steven S. Saliterman Introductory Medical Device Prototyping Introductory Medical Device Prototyping Department of Biomedical Engineering, University of Minnesota http://saliterman.umn.edu/ Images courtesy of Haas You must complete safety instruction before using

More information

6 Series Mill Controller Operation Manual

6 Series Mill Controller Operation Manual 6 Series Mill Controller Operation Manual Date: 2015/11/13 Version: 1.3 2 Contents 1 Function Key and System Configuration... 4 1.1 Main Screen Sections... 4 1.2 CNC System Configuration... 5 1.3 Coordinate...

More information

Operation Manual (B) KVR-2418 (24L) Fanuc OiMD CNC. KENT INDUSTRIAL (USA) INC Edinger Ave., Tustin, CA 92780

Operation Manual (B) KVR-2418 (24L) Fanuc OiMD CNC. KENT INDUSTRIAL (USA) INC Edinger Ave., Tustin, CA 92780 Operation Manual (B) KVR-2418 (24L) Fanuc OiMD CNC KENT INDUSTRIAL (USA) INC. 1231 Edinger Ave., Tustin, CA 92780 Tel: (714) 258-8526 Fax: (714) 258-8530 Internet: WWW.KENTUSA.COM KENT USA THE WAY TO AFFORDABLE

More information

Ladybird Project - Vacuum Mould

Ladybird Project - Vacuum Mould - Vacuum Mould Prerequisite Mould drawn and saved as STL file from Solidworks Focus of the Lesson On completion of this exercise you will have completed: Opening STL file Setting Machining Constraints

More information

GSK218M Milling Machine CNC System

GSK218M Milling Machine CNC System GSK218M Milling Machine CNC System GSK218M is widespread CNC system (matched with machining center and general milling machine) employed with 32-bit high performance CPU and super-large-scale programmable

More information

Operation Manual. 3.1 Absolute coordinate Relative coordinate Mechanical coordinate

Operation Manual. 3.1 Absolute coordinate Relative coordinate Mechanical coordinate DELTA_NC300_O_EN_20130624 Operation Manual Table of content NC300 Chapter 1: Table of group menu 1.1 Table of system group menu... 1-1 1.2 Primary control panel function keys... 1-9 1.3 Secondary control

More information

CIRCULAR INTERPOLATION COMMANDS

CIRCULAR INTERPOLATION COMMANDS PROGRAMMING JANUARY 2005 CIRCULAR INTERPOLATION COMMANDS G02 CW CIRCULAR INTERPOLATION MOTION & G03 CCW CIRCULAR INTERPOLATION MOTION *X Circular end point X-axis motion *Y Circular end point Y-axis motion

More information

Coordinate System Techniques

Coordinate System Techniques Coordinate System Techniques In this lesson, we ll show some advanced implications of what can be done with coordinate systems. For the most part, this lesson applies to machining centers. But there are

More information

NCT. PLC Programmer s Manual. Machine Tool Controls. From SW Version x.061 (M) (L)

NCT. PLC Programmer s Manual. Machine Tool Controls. From SW Version x.061 (M) (L) NCT Machine Tool Controls PLC Programmer s Manual From SW Version x.061 (M) (L) Produced and developed by NCT Automation kft. H1148 Budapest Fogarasi út 7 : Letters: 1631 Bp. P.O. Box 26 F Phone: (+36

More information

OPERATION MANUAL. TYPE:C-Type Series CONTROLLER:FANUC 0iMD / 18iMB / 31iB VERSION NO.:AFEQFI03 DATE:2012/05/03 AWEA MECHANTROINC CO.

OPERATION MANUAL. TYPE:C-Type Series CONTROLLER:FANUC 0iMD / 18iMB / 31iB VERSION NO.:AFEQFI03 DATE:2012/05/03 AWEA MECHANTROINC CO. OPERATION MANUAL TYPE:C-Type Series CONTROLLER:FANUC 0iMD / 18iMB / 31iB VERSION NO.:AFEQFI03 DATE:2012/05/03 AWEA MECHANTROINC CO., LTD NO.15,Keyuan 2nd Rd., Taichung City, Taiwan. 40763 TEL:886-4-2462-9698

More information

VERTICAL MACHINING CENTER OPERATION MANUAL I-SERIES-CAM

VERTICAL MACHINING CENTER OPERATION MANUAL I-SERIES-CAM VERTICAL MACHINING CENTER OPERATION MANUAL I-SERIES-CAM 07.10,2010 FANUC 18M,0I,18I,21I 1. PREFACE... 1-1 2. INSTALLATION AND POWER ON... 2-1 2.1 INPUT POWER ON... 2-2 2.2 SPECIFICATIONS OF ELECTRICAL

More information

201: Transfer condition. Understanding parameters

201: Transfer condition. Understanding parameters Understanding parameters All CNC users will eventually have to become familiar with parameters. Though they are not even mentioned in most basic CNC courses, and though most CNC people would agree that

More information

Operation Manual DOOSAN Tool load Monitor for Turning Centers (DTML) Release Version 3.X Under-load detect version

Operation Manual DOOSAN Tool load Monitor for Turning Centers (DTML) Release Version 3.X Under-load detect version Operation Manual DOOSAN Tool load Monitor for Turning Centers (DTML) Release Version 3.X Under-load detect version Quick setup Guide For detailed information and operation of the Tool Load Monitor, please

More information

Mach4 CNC Controller Mill Programming Guide Version 1.0

Mach4 CNC Controller Mill Programming Guide Version 1.0 Mach4 CNC Controller Mill Programming Guide Version 1.0 1 Copyright 2014 Newfangled Solutions, Artsoft USA, All Rights Reserved The following are registered trademarks of Microsoft Corporation: Microsoft,

More information

VMC600II VMC800II VMC1000II

VMC600II VMC800II VMC1000II OPERATOR S MANUAL Revised: March 15, 2001 VMC600II VMC800II VMC1000II Vertical Machining Centers Equipped with the Hardinge / Fanuc Control System II Manual No. M-378 Litho in U.S.A. Part No. M -0009500-0378

More information

Turning your ideas into reality Novakon MPG Manual

Turning your ideas into reality Novakon MPG Manual Novakon MPG Manual The E-STOP switch button on your Novakon CNC Control Pendant only provides Emergency STOP signal to Mach3 CNC application. For further protection in CNC operation, other emergency protection

More information

Section 20: Graphics

Section 20: Graphics Section 20: Graphics CNC 88HS Graphics Graphics Menu The graphics menu of the page editor has been designed to allow the user to view the part path of the current program in memory. The graphics can be

More information

G & M Code REFERENCE MANUAL. Specializing in CNC Automation and Motion Control

G & M Code REFERENCE MANUAL. Specializing in CNC Automation and Motion Control REFERENCE MANUAL Specializing in CNC Automation and Motion Control 2 P a g e 11/8/16 R0163 This manual covers definition and use of G & M codes. Formatting Overview: Menus, options, icons, fields, and

More information

ADT-CNC4620 CNC46XX Series CNC System Maintenance Manual

ADT-CNC4620 CNC46XX Series CNC System Maintenance Manual ADT-CNC4620 CNC46XX Series CNC System Maintenance Manual Add: 5/F, Tianxia IC Industrial Park, Yiyuan Rd, Nanshan District, Shenzhen Postal code: 518052 Tel: 0755-26099116 Fax: 0755-26722718 E-mail: export@machine-controller.com

More information

3300M/MK CNC Programming and Operations Manual

3300M/MK CNC Programming and Operations Manual 3300M/MK CNC Programming and Operations Manual www.anilam.com P/N 70000381C - Contents Section 1 - CNC Programming Concepts Programs... 1-1 Axis Descriptions... 1-1 X Axis... 1-2 Y Axis... 1-2 Z Axis...

More information

Mill Series Training Manual. Haas CNC Mill Operator

Mill Series Training Manual. Haas CNC Mill Operator Haas Factory Outlet A Division of Productivity Inc Mill Series Training Manual Haas CNC Mill Operator Revised 022613 (032512) (printed 022613) This Manual is the Property of Productivity Inc The document

More information

FANUC OPEN CNC OPERATOR S MANUAL BASIC OPERATION PACKAGE 2 B-63924EN/01

FANUC OPEN CNC OPERATOR S MANUAL BASIC OPERATION PACKAGE 2 B-63924EN/01 FANUC OPEN CNC BASIC OPERATION PACKAGE 2 OPERATOR S MANUAL B-63924EN/01 No part of this manual may be reproduced in any form. All specifications and designs are subject to change without notice. The export

More information

Mach4 CNC Controller Lathe Programming Guide Version 1.0

Mach4 CNC Controller Lathe Programming Guide Version 1.0 Mach4 CNC Controller Lathe Programming Guide Version 1.0 1 Copyright 2014 Newfangled Solutions, Artsoft USA, All Rights Reserved The following are registered trademarks of Microsoft Corporation: Microsoft,

More information

Operating Manual PA 8000 NT

Operating Manual PA 8000 NT PA 8000 NT PA Power Automation User documentation PA 8000 NT Edition 11.01 Software Revision 1.9 Copyright PA SUBJECT TO TECHNICAL MODIFICATIONS AND ERRORS PA Power Automation AG Gottlieb-Daimler-Str.

More information

General technology basics. Working through this module you become familiar with the most important technological aspects and machine functions.

General technology basics. Working through this module you become familiar with the most important technological aspects and machine functions. M551 General technology basics 1 Brief description Objective of the module: Working through this module you become familiar with the most important technological aspects and machine functions. Description

More information

Memory Upgrade for the Fanuc 15B CNC

Memory Upgrade for the Fanuc 15B CNC Memory Upgrade for the Fanuc B CNC Installation Instructions Copyright Memex Automation Inc. Harvester Road Burlington, Ontario Canada LN N Ph: -- Fax: -- www.memex.ca Part of the Astrix Group of Companies

More information

MEMEX FANUC METER (512K) HSL5/MME MEMORY UPGRADE INSTALLATION AND USER MANUAL M100704A

MEMEX FANUC METER (512K) HSL5/MME MEMORY UPGRADE INSTALLATION AND USER MANUAL M100704A MEMEX FANUC 9 1280 METER (512K) HSL5/MME MEMORY UPGRADE INSTALLATION AND USER MANUAL Memex Inc. 105-3425 Harvester Road, Burlington, Ontario Canada L7N 3N1 Phone: 905-635-3040 Fax: 905-631-9640 http://www.memex.ca

More information

4.10 INVOLUTE INTERPOLATION (G02.2, G03.2)

4.10 INVOLUTE INTERPOLATION (G02.2, G03.2) B 63014EN/02 POGAMMNG 4. NTEPOLATON FUNCTONS 4.10 NVOLUTE NTEPOLATON (G02.2, G03.2) nvolute curve machining can be performed by using involute interpolation. nvolute interpolation ensures continuous pulse

More information

Operation Manual. 3.1 Absolute coordinate Relative coordinate Mechanical coordinate

Operation Manual. 3.1 Absolute coordinate Relative coordinate Mechanical coordinate DELTA_NC300_O_EN_20140428 Operation Manual NC300 Table of content Chapter 1: Table of group menu 1.1 Table of system group menu... 1-1 1.2 Primary control panel function keys... 1-9 1.3 Secondary control

More information

Wheel repair and refurbishment application manual

Wheel repair and refurbishment application manual refurbishment application manual Contents 1. GENERAL DESCRIPTION... 1 2. DIGITIZING... 2 Purpose... 2 Using method... 2 Digitizing operation... 4 Protection or limitations:... 8 Digitizing result checking...

More information

Warranty. Student Workbook for Three-Axis Systems

Warranty. Student Workbook for Three-Axis Systems www.anilam.com P/N 70000505 - Warranty Warranty ANILAM warrants its products to be free from defects in material and workmanship for one (1) year from date of installation. At our option, we will repair

More information

Mach4 CNC Controller Mill Programming Guide Version 1.1 Build 3775

Mach4 CNC Controller Mill Programming Guide Version 1.1 Build 3775 Mach4 CNC Controller Mill Programming Guide Version 1.1 Build 3775 Copyright 2014 Newfangled Solutions, Artsoft USA, All Rights Reserved The following are registered trademarks of Microsoft Corporation:

More information

DIFFERENCES FROM SERIES 0i-C

DIFFERENCES FROM SERIES 0i-C B DIFFERENCES FROM SERIES 0i-C Appendix B, "Differences from Series 0i-C", consists of the following sections: B.1 SETTING UNIT...247 B.2 AUTOMATIC TOOL OFFSET...247 B.3 CIRCULAR INTERPOLATION...249 B.4

More information

Conversational Programming for 6000M, 5000M CNC

Conversational Programming for 6000M, 5000M CNC Conversational Programming for 6000M, 5000M CNC www.anilam.com P/N 70000486F - Contents Section 1 - Introduction Section 2 - Conversational Mode Programming Hot Keys Programming Hot Keys... 2-1 Editing

More information

Manufacturing Processes with the Aid of CAD/CAM Systems AMEM 405

Manufacturing Processes with the Aid of CAD/CAM Systems AMEM 405 AMEM 405 slide 1 Manufacturing Processes with the Aid of CAD/CAM Systems AMEM 405 Dr. Sotiris Omirou AMEM 405 slide 2 CONTENTS 1. CAD/CAM definition 2. Review of Milling Process 3. Know The CNC Machine

More information

MEMEX YASNAC MX3/LX3 MEMORY INSTALLATION MANUAL

MEMEX YASNAC MX3/LX3 MEMORY INSTALLATION MANUAL MEMEX YASNAC MX3/LX3 MEMORY INSTALLATION MANUAL Memex Inc. 105 3425 Harvester Rd. Burlington, Ontario Canada L7N 3N1 www.memex.ca 2017 Memex Inc. All Rights Reserved. Yasnac is a trademark of Yaskawa Ltd.

More information

CNC Turning. Module2: Introduction to MTS-TopTurn and G & M codes. Academic Services PREPARED BY. January 2013

CNC Turning. Module2: Introduction to MTS-TopTurn and G & M codes. Academic Services PREPARED BY. January 2013 CNC Turning Module2: Introduction to MTS-TopTurn and G & M codes PREPARED BY Academic Services January 2013 Applied Technology High Schools, 2013 Module2: Introduction to MTS-TopTurn and G & M codes Module

More information

Computer Aided Engineering Applications 3. Advanced Manufacturing 3.5 NC programming 3.6 Automated Manufacturing systems 3.7 Rapid prototyping

Computer Aided Engineering Applications 3. Advanced Manufacturing 3.5 NC programming 3.6 Automated Manufacturing systems 3.7 Rapid prototyping Computer Aided Engineering Applications 3. Advanced Manufacturing 3.5 NC programming 3.6 Automated Manufacturing systems 3.7 Rapid prototyping Engi 6928 - Fall 2014 3.5 Part programming Structure of an

More information

FAGOR AUTOMATION MC TRAINING MANUAL

FAGOR AUTOMATION MC TRAINING MANUAL FAGOR AUTOMATION MC TRAINING MANUAL ACER MC TRAINING MANUAL 8 holes 1/2" depth grid pattern R0.125 1.5 6 unit: inch R0.25 4 1.25 2 2.675 1/2" depth rectangular pocket 1/2" depth circular pocket R0.75 8

More information

CAD/CAM/CAE Computer Aided Design/Computer Aided Manufacturing/Computer Aided Manufacturing. Part-9 CNC Fundamentals

CAD/CAM/CAE Computer Aided Design/Computer Aided Manufacturing/Computer Aided Manufacturing. Part-9 CNC Fundamentals CAD/CAM/CAE Computer Aided Design/Computer Aided Manufacturing/Computer Aided Manufacturing Part-9 CNC Fundamentals CNC Fundamentals All CNC machine tools follow the same standard for motion nomenclature

More information

CNC Milling System Operation Manual

CNC Milling System Operation Manual HNC-08M CNC SYSTEM CNC Milling System Operation Manual V1.22 2011/01 WuHan HuaZhong Numerical Control Co., Ltd Table of Contents 1 SUMMARIZE...1 1.1 CNC SOFTWARE SYSTEM INTRODUCTION...1 1.1.1 CNC System

More information

Calibration and setup of a tool probe

Calibration and setup of a tool probe Calibration and setup of a tool probe Fundamentals Tool-setting is the process of determining geometric information length, radius and / or diameter of a cutting tool using a tool-setting device. Some

More information

USB Indexer USB Indexer for CNC Controls

USB Indexer USB Indexer for CNC Controls USB Indexer USB Indexer for CNC Controls 2009-2011 Calmotion LLC, All rights reserved Calmotion LLC 9909 Topanga Canyon Blvd. #322 Chatsworth, CA 91311 www.calmotion.com -1 2009-2011Calmotion LLC, All

More information

COPYCAT NEW FANGLED SOLUTIONS 2/6/2009

COPYCAT NEW FANGLED SOLUTIONS 2/6/2009 1.0 INTRODUCTION 1.1 CopyCat is a unique wizard used with MACH3. It is not a stand alone program. This wizard will allow you to jog a machine around and create a Gcode file from the movement. 2.0 REQUIREMENTS

More information

6000i CNC User s Manual

6000i CNC User s Manual 6000i CNC User s Manual January 2008 Ve 02 627785-21 1/2008 VPS Printed in USA Subject to change without notice www.anilam.com P/N 627785-21 - Warranty Warranty ANILAM warrants its products to be free

More information

Chapters. 1. Overview Getting started Step wise guide to code generator... 6

Chapters. 1. Overview Getting started Step wise guide to code generator... 6 Chapters 1. Overview... 2 2. Getting started... 3 3. Step wise guide to code generator... 6 1 Overview Introduction PrimeTurning is a new methodology which enables you to do turning in all directions in

More information

3300M CNC Control Training Guide

3300M CNC Control Training Guide 3300M CNC Control Training Guide Turning the Control ON After the control has been turned ON press F10 F10 to continue. Then press Select to select next page 1 Main Areas of the Display Programmed Position

More information

5000M CNC Programming and Operations Manual

5000M CNC Programming and Operations Manual 5000M CNC Programming and Operations Manual www.anilam.com P/N 70000508G - Warranty Warranty ANILAM warrants its products to be free from defects in material and workmanship for one (1) year from date

More information

MANUFACTURING PROCESSES

MANUFACTURING PROCESSES MANUFACTURING PROCESSES - AMEM 201 Lecture 7: CNC MACHINE TOOLS 1 CNC MACHINE TOOLS TERMINOLOGY NC Numerical Control CNC Computer Numerical Control CAD Computer Aided Design CAM Computer Aided Manufacturing

More information

Table of Contents. Fadal. Operator Manual

Table of Contents. Fadal. Operator Manual Table of Contents Power On/Off... 3 Pre-Startup Checks... 3 Power On for System 97/99... 4 Automatic Cold Start... 5 Wrong Power Off Procedure... 6 Auto Startup Program... 7 Power Off Procedure... 9 Pendant...

More information

Course Outline for SELCA Training

Course Outline for SELCA Training Course Outline for SELCA Training ISO Programming Conversational Programming Selca special language Programming PROGET2 Rotary table programming 5 axes tilting Head and table programming For S3000 series

More information

Triax A/T QUICK START GUIDE

Triax A/T QUICK START GUIDE Triax A/T QUICK GUIDE Please read all instructions carefully before operating your Triax A/T Key Machine. 1. Preparation A. First remove the Triax A/T machine from its cardboard box and pallet. The machine

More information

Memory Upgrade for the Fanuc 16B (0010) Series CNC FROM Module Installation

Memory Upgrade for the Fanuc 16B (0010) Series CNC FROM Module Installation Memory Upgrade for the Fanuc B () Series CNC FROM Module Installation Installation Instructions Memex Automation Harvester Rd., Burlington, Ontario Canada LN N Phone: -- Fax: -- Memex Automation All rights

More information

3000M CNC Programming and Operations Manual for Three- and Four-Axis Systems

3000M CNC Programming and Operations Manual for Three- and Four-Axis Systems 3000M CNC Programming and Operations Manual for Three- and Four-Axis Systems www.anilam.com 70000504H - Warranty Warranty ANILAM warrants its products to be free from defects in material and workmanship

More information

FANUC ihmi Human Machine Interface

FANUC ihmi Human Machine Interface 1 FANUC ihmi Human Machine Interface 2 FANUC Operating Panels PANEL ih / ih Pro 3 PANEL ih CNC LCD-mounted CNC Stand-Alone Display unit with Microsoft Windows Compact 7 for CNC of 30i series MODEL B ihmi

More information

User s Manual V MillPlus IT. NC Software

User s Manual V MillPlus IT. NC Software User s Manual V600-02 MillPlus IT NC Software 538 952-02 538 953-02 538 954-02 538 955-02 538 956-02 English (en) 6/2008 Controls on the visual display unit Select window User keys Manual operation Axis-direction

More information

GE Fanuc Automation. Series 0i Model A. Computer Numerical Control Products. Parameter Manual

GE Fanuc Automation. Series 0i Model A. Computer Numerical Control Products. Parameter Manual GE Fanuc Automation Computer Numerical Control Products Series 0i Model A Parameter Manual GFZ-63510EN/01 June 2000 Warnings, Cautions, and Notes as Used in this Publication GFL-001 Warning Warning notices

More information

HFOMN/Haas CNC Series

HFOMN/Haas CNC Series Haas Factory Outlet A Division of Productivity Inc HFOMN/Haas CNC Series Mill Operator Training Manual with NG2 Next Generation Control & VPS (Visual Programming System) Rev 2/2017 This Manual is the

More information

Craftsman CNC. LinuxCNC. Custom developed for Craftsman CNC Routers

Craftsman CNC. LinuxCNC. Custom developed for Craftsman CNC Routers Craftsman CNC LinuxCNC Custom developed for Craftsman CNC Routers Menu File Load gcode Load a gcode program Recent gcode Shows the 10 most recently opened gcode programs Close gcode Closes the current

More information

Software designed to work seamlessly with your CNC Masters machine. Made to work with Windows PC. Works with standard USB

Software designed to work seamlessly with your CNC Masters machine. Made to work with Windows PC. Works with standard USB Software designed to work seamlessly with your CNC Masters machine Made to work with Windows PC Works with standard USB Clutter free interface. The software is engineered for the machine so you don t have

More information

Table of Contents. Table Of Contents. Access to parameters (lesson 2)) 26 Surprised? 26 Key Points for Lesson 1: 26 Quiz 26

Table of Contents. Table Of Contents. Access to parameters (lesson 2)) 26 Surprised? 26 Key Points for Lesson 1: 26 Quiz 26 Preface 9 Why you should buy this book 9 What is parametric programming? 10 A word about CAM systems 10 Scope 10 Versions of Custom Macro 10 Machine types 10 Prerequisites 11 Optional status 11 Lessons

More information

CNC C6/C64/C64T PROGRAMMING MANUAL (LATHE TYPE) BNP-B2264D(ENG)

CNC C6/C64/C64T PROGRAMMING MANUAL (LATHE TYPE) BNP-B2264D(ENG) CNC C6/C64/C64T PROGRAMMING MANUAL (LATHE TYPE) BNP-B2264D(ENG) MELDAS is a registered trademark of Mitsubishi Electric Corporation. Other company and product names that appear in this manual are trademarks

More information

OPENcontrol. End User Manual

OPENcontrol. End User Manual OPENcontrol End User Manual DOCUMENT NUMBER: 4602H RELEASE REF.: EDITION: 00 AUTHOR: DATE: June 2013 PRIMA ELECTRO reserves the right to modify and improve the product described in this manual at any time

More information

CNC Programming Simplified. EZ-Turn Tutorial.

CNC Programming Simplified. EZ-Turn Tutorial. CNC Programming Simplified EZ-Turn Tutorial www.ezcam.com Copyright Notice This manual describes software that contains published and unpublished works of authorship proprietary to EZCAM Solutions, Inc.

More information

CNC Knee Type Milling Machines with USA CENTROID M-400S CNC control

CNC Knee Type Milling Machines with USA CENTROID M-400S CNC control CNC Knee Type Milling Machines with USA CENTROID M-400S CNC control GMM-949-CNC, 9 x49 table, R8, vari-speed, 3 axis CNC... GMM-949F-CNC, 9 x49 table, R8, inverter drive, 5,000 rpm, 3 axis CNC.. Note:

More information

PROGRAMMING WORKBOOK HAAS AUTOMATION, INC 2800 Sturgis Rd Oxnard, CA 93030 January 2004 JANUARY 2004 PROGRAMMING HAAS AUTOMATION INC 2800 Sturgis Road Oxnard, California 93030 Phone: 805-278-1800 www

More information

Generic Milling Manual

Generic Milling Manual COMPUTERISED MACHINES AND SYSTEMS Generic Milling Manual Denford Limited Birds Royd Brighouse West Yorkshire HD6 1NB Tel: +44 (0)1484 712264 Fax: +44 (0)1484 722160 CONTENTS - 0.0 EMail: service@denford.co.uk

More information

Century Star Turning CNC System. Programming Guide

Century Star Turning CNC System. Programming Guide Century Star Turning CNC System Programming Guide V3.5 April, 2015 Wuhan Huazhong Numerical Control Co., Ltd 2015 Wuhan Huazhong Numerical Control Co., Ltd Preface Preface Organization of documentation

More information

Running a Job on the Large Mill

Running a Job on the Large Mill Running a Job on the Large Mill Digital Media Tutorial Written by Trevor Williams Turning On the Machine Flip the breaker switch on the front right of the lower part of the controller box to the ON position.

More information

MotionOne CM G&M Code Programming Manual

MotionOne CM G&M Code Programming Manual SystemOne CM CNC 2 MotionOne CM MotionOne CM Valid for G&M Code version since: V 6.06.04.00 Doc version: V 7.00.00.01 The German version is the original of this manual. All rights are reserved with respect

More information

CNC 8055 MC EXAMPLES MANUAL REF Ref. 0601

CNC 8055 MC EXAMPLES MANUAL REF Ref. 0601 EXAMPLES MANUAL Ref. 0601 All rights reserved. No part of this documentation may be copied, transcribed, stored in a data backup system or translated into any language without Fagor Automation's explicit

More information

CHAPTER 12. CNC Program Codes. Miscellaneous CNC Program Symbols. D - Tool Diameter Offset Number. E - Select Work Coordinate System.

CHAPTER 12. CNC Program Codes. Miscellaneous CNC Program Symbols. D - Tool Diameter Offset Number. E - Select Work Coordinate System. General CHAPTER 12 CNC Program Codes The next three chapters contain a description of the CNC program codes and parameters supported by the M-Series Control. The M-Series Control has some G codes and parameters

More information

CENTROID. M-SERIES Operator's Manual. Version 8.22 Rev U.S. Patent # Centroid Corp. Howard, PA 16841

CENTROID. M-SERIES Operator's Manual. Version 8.22 Rev U.S. Patent # Centroid Corp. Howard, PA 16841 CENTROID M-SERIES Operator's Manual Version 8.22 Rev. 030826 U.S. Patent #6490500 2004 Centroid Corp. Howard, PA 16841 CNC Control Information Sheet Fill out the following and fax back to Centroid Tech

More information

NOTE This function is optional.

NOTE This function is optional. 5.AUTOMATIC OPERATION B-63943EN-1/03 5.8 RETRACE M Overview The tool can retrace the path along which the tool has moved so far (reverse execution). Furthermore, the tool can move along the retraced path

More information

HDS Series Quick Start Guide.

HDS Series Quick Start Guide. Techno-Osai Start Up Sequence HDS Series Quick Turn the Main power switch to the ON Position. 220 volts should have been attached to this switch by an electrician. Power On Button. Computer power ON. The

More information

OmniTurn Training Manual

OmniTurn Training Manual OmniTurn Training Manual Phone (631) 694-9400 Fax (631) 694-9415 1 2 OmniTurn Control Welcome to our world This manual will guide first time users to startup, home, enter, edit, and run programs. First

More information

GE Fanuc Automation. Power Mate D and F Motion Controllers. PowerMotion Products. Operation and Maintenance Manual

GE Fanuc Automation. Power Mate D and F Motion Controllers. PowerMotion Products. Operation and Maintenance Manual GE Fanuc Automation PowerMotion Products Power Mate D and F Motion Controllers Operation and Maintenance Manual GFZ-0EN/0 January 1 1. CRT/MDI AND LCD/MDI PANEL 1.1 Keyboard Layout and Names (1) CRT/MDI

More information

MELDAS, MELDASMAGIC, and MELSEC are registered trademarks of Mitsubishi Electric Corporation. The other company names and product names are

MELDAS, MELDASMAGIC, and MELSEC are registered trademarks of Mitsubishi Electric Corporation. The other company names and product names are MELDAS, MELDASMAGIC, and MELSEC are registered trademarks of Mitsubishi Electric Corporation. The other company names and product names are trademarks or registered trademarks of the respective companies.

More information