shop online:

Size: px
Start display at page:

Download "shop online:"

Transcription

1 Process systems Liquid ring vacuum pumps Single stage pumps 8 Alpha series single stage liquid ring vacuum pumps 9 AL series single stage liquid ring vacuum pumps 97 Two stage pumps 00 SHR series liquid ring vacuum pumps 5 Steam ejector vacuum systems Deaeration equipment 8 77 Air blowers and compressors BOC Edwards has purchased the vacuum and pressure interests of The Smiths Group. The businesses acquired, were part of Smith's Sealing Solutions Division, and are comprised of Stokes Vacuum, Hick Hargreaves, Hibon and Wilhelm Klein (WKE). This section reflects the Stokes Vacuum product lines now sold by BOC Edwards. shop online: The dimension drawings in this section display both metric and imperial measurements. Imperial measurements are shown in brackets.

2 LIQUID RING VACUUM PUMPS How it works 8 78 Liquid ring vacuum pumps continue to provide the optimum solution for many rough vacuum applications in the chemical and allied process industries. The general reliability, low maintenance requirements, low vibration and noise levels coupled with the unique capabilities when handling wet gases all contribute to the popularity of the pump. Operating range Liquid ring pumps are suitable for continuous operation on vacuum applications at any suction pressure down to 0 mbar A. Standard performance data is based upon 5 C water as the seal liquid, lower pressures may be possible with alternative sealing liquid. A wide range of capacities are offered from two basic pump configurations, single and two stages. The single stage range is capable of operation at 0 mbar A where required but is most suited to applications with continuous operation at inlet pressures from atmospheric down to 00 mbar A. The smallest pump in the range is a 5 m h - close coupled model whilst the largest is 000 m h -. The two-stage range is most effective on applications with continuous operation below 00 mbar A and has models from 00 up to 5000 m h -. Detailed performance data is shown in the following pages. (m /hr) Dry Air Stage Stage Suction Pressure (mbar A) Comparison of Single and two stage performance The standard construction material is cast iron with a spheroidal graphite impeller. However one of the main features of the liquid ring pump is the availability of various alternative materials of construction the main options are stainless steel, aluminum bronze, and duplex stainless steels. Some pump sizes which are particularly suited to the pharmaceutical industry are also available in hastelloy. For details on material availability please contact your local sales office. Suction 5 Sealing ring Discharge Direction of rotation Discharge port 7 Suction port 4 Casting 8 impeller The impeller is mounted eccentrically to the axis of the pump casing, the liquid ring circulates concentrically within the axis of the casing. Process gases are drawn through the inlet port into the impeller cells where the gas is compressed and discharged through the discharge port. The seal liquid which forms the liquid ring is supplied at a pressure equal to the discharge pressure of the pump, which allows the pump to automatically make up the amount of liquid which is discharged through the discharge port, therefore removing the heat of compression from the pump. APPLICATIONS Some of the more common processes which utilize liquid ring technology are listed below. Distillation Filtration Evaporation Drying Stripping Solvent recovery Deaeration These processes are used in a wide range of industries and applications, these include: Chemical processing Food processing and packaging Pharmaceutical production Oil exploration and refining Glass Industry Tobacco conditioning Packaging Electronics Industry Automobile components Power generation Waste collection Building materials Soil remediation For North American orders shop online: or call:

3 Systems Liquid ring pumps are offered in a number of standard configurations, with a selection of seal liquid systems to suit the particular application and environment. Once- through This is the most basic configuration available, it comprises of a pump complete with electric motor and drive and a discharge separator. The seal liquid is supplied to the pump and as the name suggests it goes once through and is then discharged to waste. These days this arrangement is rarely used as environmental considerations ensure that the discharge of waste liquid is kept to a minimum. Partial recirculation Again the name is self explanatory with part of the seal liquid being re-circulated, in order to remove sufficient heat from the liquid that is to be recirculated fresh cooler liquid must be added to it. This is achieved by restricting the amount of fresh liquid supplied to the pump to approximately 50% of the total required and allowing the pump to pull the balance of liquid required from the discharge separator, the excess liquid that is not re-circulated goes to waste via the discharge separator overflow. Recovac system NEW Total recirculation Total recirculation is used where it is desirable to minimize waste liquid from the pump. All of the liquid is re-circulated back into the pump via a heat exchanger, which removes the heat of compression and any latent heat of condensation from the seal liquid. The seal liquid can then be reused by the pump minimizing the effluent from the pump system. The heat exchanger device may be shell and tube, plate type or even a central cooling system. The system is of particular interest when the pump is operating on a solvent removal or drying process where process vapors are condensed within the pump, often the pump seal liquid can be the same as the condensed process vapors. Complex systems More complex systems include special recirculation systems such as the Recovac package (see later) or combinations of liquid ring pumps with roots type mechanical boosters or air, gas or steam ejectors. These hybrid systems can extend the liquid ring pump based performance envelope significantly. Performance curve of booster group The Recovac System adds a highly efficient closed circuit heat exchanger system to the inherent chemical process pumping benefits of the liquid ring vacuum pump. The result is a highly effective vacuum pump package with in built emission cleaning/solvent recovery capability. By combining the wide range of liquid ring pumps, ejectors and mechanical boosters capacities up to 0, 000 m h - can be achieved with suction pressure down to 0.0 mbar A. To make the most of the Recovac system a seal liquid which is compatible with the process should be selected, often this will be the same solvent that is being produced from the wet vacuum process. This enables condensation of process vapors in the liquid ring itself with further recovery being achieved in the falling fileat exchanger. Additional cooling can be provided for further reduction in the discharge temperature. 79 PROCESS SYSTEMS ( ) Suction Pressure (mbar) MB54 / SHR 750 G ejector MB5 / SHR SHR 750 For North American orders shop online: or call:

4 . K F E D 7 5 F E 'A' 4 G J H 'C' 'B' Liquid ring pump D Suction connection Non-return valve E Primary cooling in/outlet connections Ejector (optional) F Secondary cooling in/outlet connections 4 Drive motor G Overflow connection 5 Ring liquid heat exchanger H Drain connection Ring liquid storage tank J Make up connection 7 Exhaust gas heat exchanger (optional) K Vent connection UNIT SIZE MOTOR SIZE SUCTION VOLUME A B C D E F G H J K TANK CAPACITY () (m h - ) (mm) (mm) (mm) (DN) (DN) (DN) (DN) (DN) (DN) (DN) (liters) JSF JSF JSF JSF JSF JSF JSF JSF JSF JSF For North American orders shop online: or call:

5 Standard recovac packages NEW Optional exhaust gas condenser/absorber filter 8 Gas inlet Coolant in 9 Optional ejector complete with non-return valve Coolant out 0 Liquid collection receiver 4 Gas outlet Make-up connection 5 Ring liquid cooler Recycle to process Liquid ring vacuum pump Drain 7 Motive air 8 PROCESS SYSTEMS For North American orders shop online: or call:

6 LRM5 SINGLE STAGE PUMP Torr ft min LRM mbar 8 to Curved blade impeller and variable discharge port for optimum performance Variable pitch dynamically balanced impeller for low noise and vibration level DIN 490 mechanical seal Nominal capacity 5 m h rpm 0.75 Service water flow 0. m h Hz 50 Hz Hz 50 Hz Pa Torr LRM mbar Pa Performance details 0 Hz Nominal capacity m h rpm. Service water flow 0. m h - 0 (.0) (.5) 9 (5.59) 70 (.7) Port plate Brass CF8M CF8M Body Nitrided cast iron CF8M Nitrided cast iron Shaft Motor Motor Motor Seal Carbon / ceramic / viton Carbon / ceramic / viton Carbon / ceramic / viton 59 (.) 00 (.94) " BSP 4 x Ø8 (0.) 5 (4.9) 5 (.0) LRM5 model is available with the following motor options. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 LRL5 is a pedestal version of this pump suitable for direct mounting with C face motors, it can be supplied bareshaft or with special motors. This pump can also be supplied as a complete package system, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

7 LRM50 SINGLE STAGE PUMP Torr h m min ft LRM mbar to Curved blade impeller and variable discharge port for optimum performance Variable pitch dynamically balanced impeller for low noise and vibration level DIN 490 mechanical seal Nominal capacity 45 m h rpm.5 Service water flow 0.5 m h - Performance details 0 Hz Nominal capacity 55 m h rpm. Service water flow 0.5 m h - 7 (.8) Pa Hz 50 Hz Hz 50 Hz (.54) 78.5 (7.0) 45 (7.) Torr A 00 4 x Ø8 (0.) LRM mbar (.95) Pa (5.5) 8 PROCESS SYSTEMS Port plate Nitrided cast iron CF8M Nitrided cast iron Body Nitrided cast iron CF8M Nitrided cast iron Shaft Motor Motor Motor Seal Carbon / ceramic / viton Carbon / ceramic / viton Carbon / ceramic / viton A 50 Hz 00 (.94) 0 Hz 5 (4.9) " BSP 70 (.9) LRM50 model is available with the following motor options. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 LRL50 is a pedestal version of this pump suitable for direct mounting with C face motors, it can be supplied bareshaft or with special motors. This pump can also be supplied as a complete package system, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

8 LRM90 SINGLE STAGE PUMP Torr m h min - ft to Curved blade impeller and variable discharge port for optimum performance Variable pitch dynamically balanced impeller for low noise and vibration level DIN 490 mechanical seal Nominal capacity 70 m h rpm. Service water flow 0.7 m h - Performance details 0 Hz Nominal capacity 00 m h rpm 4 Service water flow 0.8 m h Pa Hz 50 Hz Hz 50 Hz A LRM mbar Torr LRM mbar 000 (7.09) 5 4 Pa Shaft Motor Motor Motor D C B 5 (8.8) 4 x Ø E F DN PN0 A B C D E F 50 Hz 55 (0.8) 55.5 (.) 0 (.0) 5 (.9) 0 (.0) 0 (8.) 0 Hz 58 (.8).5 (.) 7 (.77) 47 (.) 90 (7.48) 50 (9.84) LRM90 model is available with the following motor options. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 LRL90 is a pedestal version of this pump suitable for direct mounting with C face motors, it can be supplied bareshaft or with special motors. This pump can also be supplied as a complete package system, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

9 LRM5 SINGLE STAGE PUMP Torr ft min to Curved blade impeller and variable discharge port for optimum performance Variable pitch dynamically balanced impeller for low noise and vibration level DIN 490 mechanical seal Nominal capacity 00 m h rpm Service water flow 0.78 m h - Performance details 0 Hz Nominal capacity 0 m h rpm 4 Service water flow 0.8 m h Pa Hz 50 Hz Hz 50 Hz A LRM mbar Torr 00 LRM5 0 0 mbar 000 (7.09) Pa 85 PROCESS SYSTEMS Shaft Motor Motor Motor D C B 5 (8.8) 4 x Ø E F DN PN0 A B C D E F 50 Hz 54 (.0) 74.5 (.87) 0 (.0) 5 (.9) 0 (.0) 0 (8.) 0 Hz 557 (.9) 8.5 (7.5) 7 (.77) 47 (.) 90 (7.48) 50 (9.84) LRM5 model is available with the following motor options. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 LRL5 is a pedestal version of this pump suitable for direct mounting with C face motors, it can be supplied bareshaft or with special motors. This pump can also be supplied as a complete package system, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

10 8 LRM50 SINGLE STAGE PUMP to Curved blade impeller and variable discharge port for optimum performance Variable pitch dynamically balanced impeller for low noise and vibration level DIN 490 mechanical seal Nominal capacity 0 m h rpm 4 Service water flow 0.8 m h - Performance details 0 Hz Nominal capacity 0 m h rpm 5.5 Service water flow 0.8 m h - Shaft Motor Motor Motor - 7 (4.45) Pa Hz 50 Hz 0 Hz 50 Hz (7.5) A 50 Hz 07.5 (.9) 0 Hz 05 (.8) Torr B 09.5 (8.5) 07 (8.5) DN PN0 LRM mbar A 00 LRM Torr min mbar 000 (7.09) B 5 (8.8) 4 x Ø (8.50) 7 (0.87) Pa ft LRM50 model is available with the following motor options. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 LRL50 is a pedestal version of this pump suitable for direct mounting with C face motors, it can be supplied bareshaft or with special motors. This pump can also be supplied as a complete package system, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

11 LRL50 SINGLE STAGE PUMP Torr m - h ft min to Curved blade impeller and variable discharge port for optimum performance Variable pitch dynamically balanced impeller for low noise and vibration level DIN 490 mechanical seal Nominal capacity 00 m h rpm 5.5 Service water flow. m h - Performance details 0 Hz Nominal capacity 0 m h rpm 7.5 Service water flow. m h - Shaft S7 S7 S7 (.4) 95 (7.8) Pa Hz 50 Hz Hz 50 Hz DN5 PN0 LRL50 model is a pedestal mounted pump and is available with the following motor options as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available LRL mbar Torr 048 (4.) 50Hz 08 (4.7) 0Hz 5 (8.90) (.) 4 x Ø8 LRL50 Ø (4.) 0 0 mbar 000 Ø (7.87) Pa 85 (5.) (7.8) Ø85 (7.8) 87 PROCESS SYSTEMS For North American orders shop online: or call:

12 LRL0 SINGLE STAGE PUMP Torr m h ft min - 88 to Curved blade impeller and variable discharge port for optimum performance DIN 490 mechanical seal Externally mounted bearings Low noise level and vibration Nominal capacity 00 m h rpm 7.5 Service water flow. m h - Performance details 0 Hz Nominal capacity 0 m h rpm Service water flow.45 m h Pa Hz 50 Hz Hz 50 Hz 8 (44.0) 50Hz 4 (47.) 0Hz 00 LRL0 LRL mbar Torr 0 0 mbar Pa 85 (5.) 00 (7.87) Body Cast iron S7 Cast iron Shaft S7 CF8M S7 (.4) 95 (7.8) 58 5 (0.) (.) DN5 PN0 4 x Ø8 LRL0 model is a pedestal mounted pump and is available with the following motor options as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

13 LRL450 SINGLE STAGE PUMP Torr to Curved blade impeller and variable discharge port for optimum performance Variable pitch dynamically balanced impeller for low noise and vibration level DIN 490 mechanical seal Nominal capacity 70 m h rpm Service water flow.45 m h - Performance details 0 Hz Nominal capacity 4 m h rpm 5 Service water flow.45 m h - Shaft S7 S7 S7 m h - (.4) 95 (7.8) Pa Hz 50 Hz Hz 50 Hz DN5 PN0 LRL mbar Torr 0 59 (49.57) 50Hz 0 (5.0) 0Hz 0 5 (.9) (.) 00 4 x Ø8 00 LRL mbar Pa (7.87) min - ft 85 (5.) 89 PROCESS SYSTEMS LRL450 model is a pedestal mounted pump and is available with the following motor options as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

14 LRS00 SINGLE STAGE PUMP Torr min - ft LRS mbar Pa Hz 50 Hz 90 to Curved blade impeller and variable discharge port for optimum performance DIN 490 mechanical seal Externally mounted bearings Low noise level vibration Torr LRS mbar Nominal capacity 5 m h rpm 5 Service water flow m h - Performance details 0 Hz Nominal capacity 5 m h rpm Service water flow. m h - Shaft S Hz 50 Hz 97 (7.44) 0 (.05) (.4) 458 (8.0) 8 (7.) 90 (.54) Ø4 (.5) 0000 DN00 PN0 5 (8.8) (5.0) 5 (8.8) 00 4 x Ø0 000 Pa 470 (8.50) (9.45) 9 (0.59) (.9) LRS00 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

15 LRS0 SINGLE STAGE PUMP Torr ft min LRS mbar Hz 50 Hz Pa to Curved blade impeller and variable discharge port for optimum performance DIN 490 mechanical seal Externally mounted bearings Low noise level vibration Nominal capacity 775 m h rpm Service water flow.5 m h - Performance details 0 Hz Nominal capacity 900 m h rpm 0 Service water flow.5 m h - Shaft S Torr Hz 50 Hz (.54) 58 (4.09) 54 (0.4) 5 (.) (7.) 90 (.54) Ø4 (.5) 0000 DN00 PN (8.8) (5.0) 5 (8.8) 00 DN00 4 x Ø0 LRS0 0 mbar 000 Pa LRS0 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available (8.50) 9 (0.59) (.9) (9.45) Ø0 Ø0 (8.) (8.) 9 PROCESS SYSTEMS For North American orders shop online: or call:

16 ALPHA 4+ SINGLE STAGE LIQUID RING VACUUM PUMP pi (mbar abs.) min - ft pi (Torr) pi (mm Hg) pi ("Hg) 9 Curved blade impeller and variable discharge port for optimum performance s Minimum number of body joints Externally mounted bearings Handles wet or dry gases Unaffected by liquid carryover Robust and simple construction to suit application Low noise level x Ø Ø Performance details at maximum speed Nominal Capacity 00 m h - Suction Pressure Nominal Speed 50 rpm Motor Power 55 Service water flow 4 m h - Performance details at minimum speed Nominal Capacity 000 m h - Suction Pressure Nominal Speed 9 rpm Motor Power 0 Service water flow.5 m h - DN50 PN0 STANDARD STAINLESS STEEL STAINLESS STEEL FITTED Impeller SG iron CF8M CF8M Shaft SG iron CF8M CF8M Alpha 4+ model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available For North American orders shop online: or call:

17 ALPHA 0+ SINGLE STAGE LIQUID RING VACUUM PUMP - ft min - Curved blade impeller and variable discharge port for optimum performance s Minimum number of body joints Externally mounted bearings Handles wet or dry gases Unaffected by liquid carryover Robust and simple construction to suit application Low noise level 5 4xØ Ø PROCESS SYSTEMS Performance details at maximum speed Nominal capacity 00 m h - 0 rpm 55 Service water flow 4 m h Performance details at minimum speed Nominal capacity m h - 9 rpm 45 Service water flow 4 m h STANDARD STAINLESS STEEL Impeller SG iron CF8M CF8M Shaft SG iron CF8M CF8M STAINLESS STEEL FITTED 0 DN50 PN Alpha 0+ model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

18 ALPHA 0+ SINGLE STAGE LIQUID RING VACUUM PUMP - ft min - 94 Curved blade impeller and variable discharge port for optimum performance s Minimum number of body joints Externally mounted bearings Handles wet or dry gases Unaffected by liquid carryover Robust and simple construction to suit application Low noise level Once through, partial or total recovery seal liquid 45 Ø Performance details at maximum speed Nominal capacity 00 m h - mbar A 8 rpm 75 Service water flow 7 m h Performance details at minimum speed Nominal capacity 500 m h - mbar A 585 rpm 7 Service water flow 5 m h STANDARD STAINLESS STEEL Impeller SG iron CF8M CF8M Shaft C45 XC48 XC48 STAINLESS STEEL FITTED DN50 PN0 Alpha 0+ model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

19 ALPHA + SINGLE STAGE LIQUID RING VACUUM PUMP - ft min - Curved blade impeller and variable discharge port for optimum performance s Minimum number of body joints Externally mounted bearings Handles wet or dry gases Unaffected by liquid carryover Robust and simple construction to suit application Low noise level 45 Ø Ø PROCESS SYSTEMS Performance details at maximum speed Nominal capacity 850 m h - 8 rpm 90 Service water flow 5 m h - Performance details at minimum speed Nominal capacity 700 m h rpm 45 Service water flow m h STANDARD STAINLESS STEEL Impeller SG iron CF8M CF8M Shaft C45 XC48 XC48 STAINLESS STEEL FITTED DN50 PN0 Alpha + model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

20 ALPHA 50+ SINGLE STAGE LIQUID RING VACUUM PUMP - ft min - 9 Curved blade impeller and variable discharge port for optimum performance s Minimum number of body joints Externally mounted bearings Handles wet or dry gases Unaffected by liquid carryover Robust and simple construction to suit application Low noise level xØ Ø Performance details at maximum speed Nominal capacity m h - 75 rpm 0 Service water flow 9 m h - Performance details at minimum speed Nominal capacity 0 m h rpm 55 Service water flow m h STANDARD STAINLESS STEEL Impeller SG iron CF8M CF8M Shaft C45 STAINLESS STEEL FITTED DN00 PN0 Alpha 50+ model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

21 AL 70+ SINGLE STAGE LIQUID RING VACUUM PUMP - min - ft Curved blade impeller and variable discharge port for optimum performance s Minimum number of body joints Externally mounted bearings Handles wet or dry gases Unaffected by liquid carryover Robust and simple construction to suit application Low noise level Ø 500 Ø / 97 PROCESS SYSTEMS Performance details at maximum speed Nominal capacity 000 m h - 50 rpm Service water flow m h - Performance details at minimum speed Nominal capacity 0 m h - rpm 75 Service water flow m h - 5 Ø / DN00 PN holes Ø CAST IRON STAINLESS STEEL STAINLESS STEEL FITTED Impeller SG iron CF8M CF8M Shaft C45 XC48 XC48 Seals Mechanical Mechanical Mechanical AL 70+ model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

22 AL 00+ SINGLE STAGE LIQUID RING VACUUM PUMP - ft min Curved blade impeller and variable discharge port for optimum performance Packed Gland or s Externally mounted bearings Handles wet or dry gases Unaffected by liquid carryover Robust and simple construction to suit application Low noise level Once through, partial or total recovery seal liquid available Ø 00 Ø / Performance details at maximum speed Nominal capacity 00 m h rpm 00 Service water flow 8 m h - 0/ Performance details at minimum speed Nominal capacity 5000 m h - 5 rpm 90 Service water flow 9 m h holes Ø DN50 PN0 CAST IRON STAINLESS STEEL STAINLESS STEEL FITTED Impeller SG iron CF8M CF8M Shaft C45 XC48 XC48 Seals Mechanical Mechanical Mechanical AL 00+ model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

23 AL + SINGLE STAGE LIQUID RING VACUUM PUMPS - ft min - Curved blade impeller and variable discharge port for optimum performance s Minimum number of body joints Externally mounted bearings Handles wet or dry gases Unaffected by liquid carryover Robust and simple construction to suit application Low noise level Ø Ø PROCESS SYSTEMS Performance details at maximum speed Nominal capacity 000 m h rpm 00 Service water flow 5 m h - Performance details at minimum speed Nominal capacity 500 m h - 90 rpm Service water flow m h Ø DN00 PN holes Ø CAST IRON STAINLESS STEEL STAINLESS STEEL FITTED Impeller SG iron CF8M CF8M Shaft C45 XC48 XC48 Seals Mechanical Mechanical Mechanical AL + model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. For North American orders shop online: or call:

24 LRS50 TWO STAGE PUMP Torr min - ft LRS mbar Pa Hz 50 Hz 00 Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Pedestal mounting option Torr LRS mbar Nominal capacity 55 m h rpm. Service water flow 0.8 m h - Performance details 0 Hz Nominal capacity 5 m h rpm Service water flow 0.8 m h - Shaft S7 S Hz 50 Hz 44 (7.) 50 (9.84) (4.57) 5 (4.7) 58 (.8) /4" BSP (.58) 00 5 (5.98) 85 (7.8) 000 LRS50 model is a bareshaft pump with a pedestal mounted option LRL50 suitable for C flange motors, following motor options are offered as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. Ø9 (0.75) Pa 00 (.94) 8 (8.58) 55 (0.04) 00 (.94) 4 x Ø (0.47) For North American orders shop online: or call:

25 LRS00 TWO STAGE PUMP Torr ft min LRS mbar Pa Hz 50 Hz Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Pedestal mounting option Nominal capacity 90 m h rpm Service water flow m h - Performance details 0 Hz Nominal capacity 00 m h rpm 4 Service water flow m h - Shaft S7 S Torr Hz 50 Hz (8.) 05 (8.07) 49 (5.87) /" BSP mbar 000 Pa LRS00 model is a bareshaft pump with a pedestal mounted option LRL00 suitable for C flange motors, following motor options are offered as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available (.4) Ø8 (.0) 00 LRS00 45 (9.5) (5.5) 05 (.0) x Ø4 (.90) (.89) (0.55) 0 (8.) (.0) (4.9) 05 (.0) 0 PROCESS SYSTEMS For North American orders shop online: or call:

26 LRS50 TWO STAGE PUMP Torr LRS mbar min - ft Pa Hz 50 Hz 0 Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Pedestal mounting option Nominal capacity 0 m h rpm 4 Service water flow.05 m h - Performance details 0 Hz Nominal capacity 50 m h rpm 5.5 Service water flow.05 m h - Shaft S7 S Torr Hz 50 Hz 55 (.77) 54 (0.0) (.84) 9 (5.47) DN PN mbar 000 Pa LRS50 model is a bareshaft pump with a pedestal mounted option LRL50 suitable for C flange motors, following motor options are offered as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available LRS50 90 (.4) 75 (.89) Ø8 (.0) 54 (.) (5.5) 0 (8.) (.0) (5.7) 95 (5.55) 75 4 x Ø5 (.89) (0.59) For North American orders shop online: or call:

27 LRS00 TWO STAGE PUMP Torr min - ft LRS mbar Pa Hz 50 Hz Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Pedestal mounting option Nominal capacity m h rpm 5.5 Service water flow.05 m h - Performance details 0 Hz Nominal capacity 00 m h rpm 7.5 Service water flow.05 m h - Shaft S7 S Torr Hz 50 Hz (4.5) 4 (.7) (5.59) 9 (5.47) DN PN mbar 000 Pa LRS00 model is a bareshaft pump with a pedestal mounted option LRL00 suitable for C flange motors, following motor options are offered as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available LRS00 90 (.4) 75 (.89) Ø8 (.0) 54 (.) (5.5) 0 (8.) x Ø5 (.89) (0.59) (.0) (5.7) 95 (5.55) 0 PROCESS SYSTEMS For North American orders shop online: or call:

28 LRS75 TWO STAGE PUMP Torr LRS mbar min - ft Pa Hz 50 Hz 04 Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Pedestal mounting option Nominal capacity 50 m h rpm 9 Service water flow. m h - Performance details 0 Hz Nominal capacity 75 m h rpm Service water flow. m h - Shaft S7 S Hz 50 Hz (.85) (.8) 5 4 (.) (8.47) 5 (.50) Torr DN50 PN0 LRS75 LRS75 model is a bareshaft pump with a pedestal mounted option LRL75 suitable for C flange motors, following motor options are offered as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available (.) Ø (.) (5.55) 0 (9.0) (9.45) 00 (.8) 0 0 mbar (7.87) (7.09) Pa 4 x Ø (0.) 500 (9.9) For North American orders shop online: or call:

29 LRS50 TWO STAGE PUMP Torr ft min LRS mbar Pa Hz 50 Hz Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Pedestal mounting option Nominal capacity 50 m h rpm Service water flow. m h - Performance details 0 Hz Nominal capacity m h rpm 5 Service water flow. m h - Shaft S7 S Hz 50 Hz Torr DN50 PN0 LRS mbar 74 (9.) 8 (5.04) 5 48 (8.98) (8.47) 5 (.50) LRS50 model is a bareshaft pump with a pedestal mounted option LRL50 suitable for C flange motors, following motor options are offered as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. 0 (.) Ø (.) 95 (5.55) 0 (9.0) (9.45) 00 (.8) (7.87) (7.09) Pa 4 x Ø (0.) 500 (9.9) 05 PROCESS SYSTEMS For North American orders shop online: or call:

30 LRS45 TWO STAGE PUMP Torr min - ft 00 LRS mbar Pa Hz 50 Hz 0 Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Pedestal mounting option Nominal capacity 75 m h rpm 5 Service water flow.4 m h - Performance details 0 Hz Nominal capacity 450 m h rpm 8.5 Service water flow.4 m h - Shaft S7 S Torr Hz 50 Hz 78 (0.79) (.) 5 5 (0.55) (8.47) 5 (.50) DN50 PN (.) Ø (.) LRS45 model is a bareshaft pump with a pedestal mounted option LRL45 suitable for C flange motors, following motor options are offered as standard. IEC Eurovoltage 0-/-45//50Hz, IP55, Class F, B/B5 IEC 0-//0Hz, IP55, Class F, B/B5 NEMA UL CSA Epact 0-//0Hz, IP55, Class F B/B5 These pumps can be supplied as complete package systems, suitable for once through, partial or total recirculation of the seal liquid. Special and hazardous motors are available on request. Custom engineered packages to meet more complex process system requirements are also available. 00 LRS45 95 (5.55) 0 (9.0) (9.45) 00 (.8) 0 0 mbar (7.09) (7.87) Pa 4 x Ø (0.) 500 (9.9) For North American orders shop online: or call:

31 LRS00 TWO STAGE PUMP Torr ft min LRS mbar Pa Hz 50 Hz Torr Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Nominal capacity 00 m h rpm Service water flow.7 m h - Performance details 0 Hz Nominal capacity 50 m h rpm 0 Service water flow.7 m h - Shaft S7 S Hz 50 Hz (.84) (7.09) DN PN mbar 000 Pa LRS00 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available LRS (.5) 45 (7.) 4 (8.90) 0 5 (9.5) (9.0) Ø4 (.5) (.54) 95 (.) 0 (4.7) (.9) 0 (8.7) 05 (.8) (8.8) 4 x Ø8 (0.7) 07 PROCESS SYSTEMS For North American orders shop online: or call:

32 LRS750 TWO STAGE PUMP Torr min - ft LRS mbar Pa Hz 50 Hz 08 Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Nominal capacity 700 m h rpm 0 Service water flow.5 m h - Performance details 0 Hz Nominal capacity 0 m h rpm 7 Service water flow.5 m h - Shaft S7 S Torr Hz 50 Hz DN PN LRS750 9 (.9) 45 (7.) 55 (.4) 0 5 (9.5) (9.0) 5 (.8) (7.09) 0 0 mbar 000 LRS750 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. Ø4 (.5) 90 (.54) 95 (.) 0 (4.7) Pa (.9) 0 (8.7) 05 (.8) (8.8) 4 x Ø8 (0.7) For North American orders shop online: or call:

33 LRS000 TWO STAGE PUMP Torr ft min LRS mbar Pa Hz Torr Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Nominal capacity 0 m h - 90 rpm 0 Service water flow m h - Performance details 0 Hz Nominal capacity 000 m h - 50 rpm 45 Service water flow 7 m h - Shaft S7 S7 4 (.47) Hz 50 Hz 9 (5.9) (.8) (7.09) 9 (5.) 44.0 (7.5) 0000 DN00 PN0 0 (4.7) LRS LRS000 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. Ø0 (.) mbar 000 Pa 70 (4.57) (5.75) 4 (8.90) 5 (8.8) 75 (0.8) 0 (.0) (.8) 4 x Ø0 (0.79) 09 PROCESS SYSTEMS For North American orders shop online: or call:

34 LRS50 TWO STAGE PUMP Torr ft min LRS mbar Pa Hz 50 Hz 0 Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Nominal capacity 00 m h - 90 rpm 7 Service water flow 7 m h - Performance details 0 Hz Nominal capacity m h - 50 rpm 55 Service water flow 8 m h - Shaft S7 S7 4 (.47) Hz 50 Hz (57.84) 9 44 (7.8) (7.09) 789 (.0) Torr (7.5) DN00 PN0 LRS50 LRS50 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available (4.7) Ø0 (.) mbar (4.57) (5.75) 4 (8.90) Pa 5 (8.8) 75 (0.8) 0 (.0) 4 x Ø0 (.8) For North American orders shop online: or call:

35 LRS750 TWO STAGE PUMP Torr ft min LRS mbar Pa Hz 50 Hz Torr Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Nominal capacity 00 m h - 90 rpm 45 Service water flow 9 m h - Performance details 0 Hz Nominal capacity 0 m h - 50 rpm 75 Service water flow 9 m h - Shaft S7 S7 4 (.47) Hz 50 Hz 59 (.77) (.) (7.09) 889 (5.0) 44.0 (7.5) 0000 DN00 PN0 LRS750 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available (4.7) Ø0 (.) LRS mbar (4.57) (5.75) 4 (8.90) Pa (8.8) 75 (0.8) (.8) 0 (.0) 4 x Ø0 PROCESS SYSTEMS For North American orders shop online: or call:

36 LRS000 TWO STAGE PUMP Torr min - ft LRS mbar Pa Hz 50 Hz Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Nominal capacity 000 m h - 75 rpm 75 Service water flow 4 m h - Performance details 0 Hz Nominal capacity 00 m h - 75 rpm 0 Service water flow 4 m h - Shaft S7 S Hz 50 Hz Torr DN50 PN0 LRS mbar 99 (7.4) (8.) (.8) (5.04) 90 (7.) 5 (.09) LRS000 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. Ø (.5) 0 (.0) 4 x Ø4 500 (9.9) 50 (0.47) 50 (5.59) Pa 4 05 (7.) (4.9) (.0) For North American orders shop online: or call:

37 LRS500 TWO STAGE PUMP Torr LRS mbar min - ft Pa Hz 50 Hz Torr Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Nominal capacity 00 m h - 75 rpm 90 Service water flow 5 m h - Performance details 0 Hz Nominal capacity 000 m h - 8 rpm Service water flow 5 m h - Shaft S7 S Hz 50 Hz DN50 PN0 LRS mbar 089 (8.4) 47 9 (8.) (8.58) (5.04) 0 (4.70) 57 (.48) LRS500 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. Ø (.5) 0 (.0) 4 x Ø4 500 (9.9) 50 (0.47) 50 (5.59) Pa 4 05 (7.) (4.9) (.0) PROCESS SYSTEMS For North American orders shop online: or call:

38 LRS500 TWO STAGE PUMP Torr min - ft LRS mbar Pa Hz 50 Hz Torr 4 Higher efficiency at low pressures Selection of materials to suit application DIN 490 mechanical seal Simple rugged design Nominal capacity 000 m h - 75 rpm 0 Service water flow 8 m h - Performance details 0 Hz Nominal capacity 700 m h - 8 rpm 50 Service water flow 8 m h - Shaft S7 S Hz 50 Hz DN50 PN0 LRS mbar 89 (8.8) 47 0 (8.) (4.5) (5.04) 0 (47.4) 57 (.48) LRS500 model is a bareshaft machine and can be supplied as part of a standard package, incorporating electric motor, baseplate and seal liquid recovery system, suitable for once through, partial or total recirculation. Custom engineered packages to meet more complex process system requirements are also available. Ø (.5) 0 (.0) 4 x Ø4 500 (9.9) 50 (0.47) 50 (5.59) Pa 4 05 (7.) (4.9) (.0) For North American orders shop online: or call:

39 SHR SERIES LIQUID RING VACUUM PUMPS NEW CAST IRON SG IRON STAINLESS STEEL FITTED Casing Cast iron SG iron Cast iron Impeller SG iron SG iron CF8M Port plate Cast iron SG iron Cast iron Body Carbon steel Carbon steel Carbon steel Shaft S7 S7 Mechanical Seal To suit process requirements STAINLESS STEEL ALUMINUM BRONZE DUPLEX STAINLESS STEEL Casing CF8M Aluminum bronze Duplex Impeller CF8M Aluminum bronze Duplex Port plate CF8M Aluminum bronze Duplex Body CF8M Aluminum bronze Duplex Shaft CF8M Monel Duplex Mechanical Seal To suit process requirements The SHR Series covers capacities from 500 to 5000 m h - with suction pressures down to 0 mbar A. The pump design incorporates many of the requirements of API 8 as standard and can be modified to meet customer specific specifications. Specialized seal arrangements, design pressures, inspection procedures, documentation and quality assurance needs can be accommodated. Generally these models will form an integral part of a fully engineered process vacuum system. Pump performance Dry Air (m /h) Suction Pressure (mbar) Performance based upon dry air at 0 C and seal water temperature of 5 C, atmospheric pressure of 0 mbar A. Subject to a 0% tolerance. SHR 00 5 SHR 500 SHR SHR 850 SHR SHR SHR SHR 500 Options s available Alternative materials of construction eg. aluminum bronze, stainless steel, duplex steel are available. PUMP SIZE G F DIMENSIONS A B C D E F G H J SHR SHR SHR SHR SHR SHR SHR SHR APPLICATIONS Vacuum filtration Condenser air evacuation Vacuum distillation Vacuum drying Central vacuum systems Evaporation Crystallizers Vacuum moulding Impregnation Deaeration A J E C B E H D 5 PROCESS SYSTEMS PRODUCT DESCRIPTION Contact BOC Edwards for information about ordering. For North American orders shop online: or call: ORDERING NUMBER

40 NEW STEAM EJECTOR VACUUM SYSTEMS BOC Edwards has over 90 years experience in the design and supply of steam ejector systems. BOC Edwards has been instrumental in the development of the steam ejector from the relatively crude single stage devices which evolved into today s highly efficient multi-stage systems. Process and mechanical design expertise is combined with project management skills for the supply of individual items of plant, or the execution of total projects including installation and commissioning. The company has an immense reputation in applications including the following: Refinery Vacuum Systems Vacuum Distillation Units Flash Evaporation for Seawater Desalination Turbine Condenser Air Extraction Edible Oil Processing Polymerization Crystallization Evaporative Cooling Features of the steam ejector solution Low Capital Cost No moving parts Low maintenance Wide choice of materials No close clearances No size limitation Ability to handle large vapor load Liquid slugs do not cause mechanical damage Not sensitive to suction temperature 7 8 Range Ejectors can be arranged as multi-stage systems with interstage condensers, which may be the direct contact type (jet condenser) or surface type (shell and tube). The multi-stage arrangements allows lower suction pressures to be achieved than could be produced by a single stage ejector. Interstage condensers economize on the use of motive steam since the operating steam from stages upstream of the condenser is condensed leaving only saturated incondensable gases to be handled by the succeeding stage or stages. Operating pressure Single Stage 50-0 mbar Two Stage 5-5 mbar Three Stage 0-7 mbar Four Stage mbar Five Stage 0. mbar As ejectors can be economically manufactured on an individual basis to suit specific customer needs they have a wide capacity range, which is limited only by the manufacturing techniques relevant to the material of construction, typically this range would be between x 0 m h Strainer 5 Diffuser Motive steam Suction Nozzle 7 Vapor Head 4 Discharge 8 Nozzle Holder For North American orders shop online: or call:

41 Interstage jet condensers Jet or spray type condensers operate by condensing steam by direct contact with the cooling water. This type of condenser can be located at barometric height or at low level using a condensate extraction pump. Jet condensers tend to use less cooling water than surface types although as the ejected vapors are in contact with the cooling water the treatment of any resulting effluent must be considered. Interstage surface condensers Surface condensers of the shell and tube type perform the same function as jet types however the ejector steam and process vapors are condensed on the tube surfaces without contact with the cooling water, greatly reducing the potential effluent problem. Removable end covers on the condensers allow easy cleaning of the tubes. Ejector and ejector liquid ring pump combinations can be supplied using BOC Edwards designed liquid ring pumps. The depth of experience in both types of equipment allows optimization of the equipment both in performance and economy of utilities. Applications and design services BOC Edwards offers a comprehensive design service based on unrivalled process vacuum experience, application knowledge and design capabilities. In order to propose a solution the following information is required at the enquiry stage: Suction flow Composition and Molecular weight Discharge temperature System volume Evacuation time Discharge pressure Motive pressure and temperature, max-normal-min Cooling water temperature, max-normal-min Type of condenser direct or indirect Type of installation Barometric or low level Design codes applicable 7 PROCESS SYSTEMS Multistage ejector/liquid ring pump combinations BOC Edwards are able to offer combinations of steam ejectors and liquid ring pumps where the liquid ring pump replaces the final stage or stages of a steam ejector system. This enables large vapor/gas flows to be handled at the low pressures associated with multi-stage steam ejector sets whilst substantially reducing steam consumption and hence operating costs. For North American orders shop online: or call:

42 8 DEAERATION EQUIPMENT BOC Edwards experience in water deaeration equipment spans more than 70 years, serving essentially two markets and applications: Seawater deaerators for water injection systems for secondary recovery of oil from offshore reservoirs Boiler feedwater and process deaeration for power generation plants, boilers and process use Seawater deaerators Secondary recovery by means of water injection is frequently an essential feature of crude oil production. It is often a crucial factor in achieving and sustaining economically viable production rates. The source of the water is dependant on the location of the production facility and could be from a subsurface source such as produced water or an aquifer, or from a surface source such as the sea or a river. The latter two sources, as with most surface waters, normally contain substantial levels of dissolved oxygen. In order to control corrosion rates in downstream plant and to inhibit bacterial growth this oxygen must be removed before the water is used for injection. BOC Edwards is able to provide extensively proven deaeration technology to facilitate the removal of this oxygen to levels such that the remaining residual may be economically removed by the addition of a chemical scavenger. The following options are available: Spray/pack deaerators Packed column deaerators Trace gas stripping deaerators Spray/pack deaerators Although conventional packed bed deaerators offer a satisfactory solution in many circumstances, the unique BOC Edwards spray packed deaerator technology offers significant advantages over conventional designs. It affords additional benefits for FPSO installations because the mass transfer efficiency of the spray section is unaffected by wave motion and by any foaming of the water as it enters the deaerator.. NEW 5 This patented design offers many benefits over conventional deaerators and compact deaerator designs including the following: Substantial height and weight reduction compared to conventional vacuum stripping columns May be used upstream of sulphate reduction membranes, since it can operate without the addition of anti-foam chemicals Unaffected by any motion of the installation, making it the preferred technology for FPSO applications There is no reliance on catalysts, which have a limited life span and may be poisoned There is no requirement for storage and/or production of hazardous combustible products such as methanol or hydrogen Extensively field-proven technology, with over 50 units utilizing the spray distributor supplied for water injection service Packed column deaerators This conventional design uses well-proven technology and remains the industry standard for both onshore and offshore applications worldwide. The design is suitable for both vacuum and gas stripping applications with corrosion resistant tower internals designed for foam retention, efficient liquid and gas phase distribution and redistribution, in order to maximize mass transfer efficiency. Trace gas stripping deaerators This patented system combines vacuum stripping and inert gas stripping to offer a unit that operates under vacuum with the mass transfer process being assisted by a small quantity of inert gas admitted into the deaerator column. This process allows highly compact deaerator columns to be used whilst the required vacuum pump capacity is substantially lower than would be associated with conventional vacuum stripping deaerators. Deaeration and the use of sulphate removal Systems BOC Edwards is able to offer field proven designs for water injection deaerators, which are required to operate upstream of sulphate removal systems. Such installations require that the deaerator must operate without antifoam agents since the use of such agents in incompatible with the membranes used in the sulphate removal system. 4 First stage vapor take-off 4 Recycle Oxygen scavenger 5 Second stage vapor take - off Water outlet Water inlet For North American orders shop online: or call:

43 Breweries - deaerating water in the production of high gravity beer. NEW BOC Edwards has supplied units to replace conventional packed column deaerator designs supplied by other manufacturers that have proved to be incapable of operating at the required design conditions without the use of antifoam agents. Our ability to offer proven technologies, which provide enhanced mass transfer capability can enable existing deaerator vessels to be re-used in order to minimize the cost and downtime associated with the upgrade. Sulphate removal systems may be installed upstream of the deaerator in which case antifoam agents may be used, however this location upstream of the deaerator column has many serious disadvantages, which include: of the sulphate removal system must be suitable for service in contact with undeaerated seawater Presence of oxygen in the seawater will increase the risk of oxidation of the membranes and/or the possibility of aerobic bacteria or algae growth on the membranes Additional precautions to ensure the removal of any hydrocarbons present in the water may be necessary prior to the sulphate removal system to ensure that these do not contact the membranes Deaeration on floating production vessels BOC Edwards has considerable experience in the supply of deaeration packages for use on floating production vessels including installations on FPSO's, semi-submersibles and on tension leg platforms. These production facilities require that the deaeration package is insensitive to the motion of the installation and that the height and weight of the package together with the elevation of the center of gravity above grade level are minimized. Our deaeration technology includes designs that are ideally suited to such floating production facilities, with references available for these types of installations at locations around the world, in conditions ranging from offshore Canada to Equatorial Africa. 5 Vent 4 Deaerated water outlet Feed water inlet 5 Off-load Heating Steam Heating steam inlet High level pressure deaerators For modern industrial installations where heat economy is essential, and where even lower oxygen contents are demanded to avoid costly maintenance work, the pressure heater/deaerator system is used where inlet boiler feed water is heated to well above atmospheric boiling point. BOC Edwards has developed a system of sprays and trays such that the feed water enters the deaerator through an atomizing spray valve assembly into the upper volume of the deaerator vessel where primary deaeration takes place. The feed then falls over a series of trays to the base of the deaerator during the course of which secondary deaeration takes placed. Heating steam is admitted via a diffuser positioned below the tray assembly to ensure ultimate heating effect and optimum scrubbing action so as to produce residual oxygen contents down to p.p.m. or less. This deaerating section is mounted on a storage compartment such that the whole system can be mounted at a suitable height to obtain the required suction head on the boiler feed pump advised by the manufacturer. 4 9 PROCESS SYSTEMS Boiler feedwater and process water deaerators The types of deaerator described have been developed over years of experience of the different types required for numerous industrial applications. Examples of some of the industries where deaeration is used are: Power stations - treating boiler feed water Oil refineries and chemical plants - treating boiler feed water and process deaeration. For North American orders shop online: or call:

44 5 0 4 Vent 4 Discharge to storage vessel Feed water inlet 5 Balance pipe return Heating steam inlet Manway For North American orders shop online: or call:

45 AIR BLOWERS AND COMPRESSORS The acquisition in 00 of the H organization comprising Hick Hargreaves (United Kingdom), Hibon (France) and Wilhelm Klein (Germany) has enabled BOC Edwards to offer to the market a world-class range of air blowers and compression equipment which are used to provide air/gas volumes at varying pressures above atmospheric, as well as for vacuum duties. The following information gives a brief overview of the ranges available. For more detailed information please contact your usual customer support division. POSITIVE DISPLACEMENT AIR BLOWERS PRODUCTS FLOW (m h - ) OPERATING PRESSURE Positive Displacement Air Blowers mbar abs - bar abs Multistage Centrifugal Blowers mbar abs - bar abs High Vacuum Air Injection mbar abs Blowers (Pre-Inlet) Dry Bulk Truck Pressure Blowers (Truckstar) mbar abs -. bar abs Process Blowers (Special Seals & Materials) mbar abs -.7 bar abs Oil Free Screw Compressor mbar abs - 4 bar abs APPLICATIONS Flows m h - Pressures to bar gauge and vacuum to 500 mbar abs Tri-lobe construction with built-in pulse control system to reduce pulsations and noise Five bearings standard with drive shaft suitable for v-belt and direct drives Oil splash lubricated bearings for long service Piston rings and labyrinth seals, lifetime guarantee Heavy duty casing and end plates with cast ribs for strength Heavy duty roller bearing at shaft end Helical gears located on the driver side for more input torque capability Better balancing to withstand fatigue Spark proof bronze impellers or gas tight mechanical seals available for special applications MARKETS NFORMATION ORDERING APPLICATIONS OEM Pneumatic Conveying X X X X Dust removal X X Vacuuandling systems X Env t Aeration X X X Biogas recovery X X Methane transfer X Sewer cleaning X Digestors X Cement Oxidation X X X Combustion air - gas X burners Homogenization X Food Fluidization X X Crystallization X Chemical Mechanical steam compression X Vacuum filtration X Gas burners X Gas transfer circulation X Vacuum swing absorption X Paper ind. Felt conditioning X Impregnation/ Dewatering X Navy Compressed air for ballasts X Radar interference X Power Flue gas desulfurization X X X Fly ash suction X AIR INJECTION TRUCKSTAR PROCESS Silent flow packages New ergonomic and compact design used with SN blower series Minimum footprint Acoustical type combined inlet filter/silencer Automatic belt tensioning system Motor lifting device for v-belt replacement Easy filter and oil changes Acoustic enclosure Developed to meet stringent noise levels Built in fan for efficient cooling Instrumentation for pressure and temperature wall mounted on the enclosure Suitable for outdoor installation PROCESS SYSTEMS For North American orders shop online: or call:

46 MULTISTAGE CENTRIFUGAL BLOWERS Applications Mobile waste handling units, industrial, municipal, wet and dry Pneumatic conveying (fly ash, chemicals, pharmaceuticals, etc) Central vacuum systems (packaging, envelope manufacturing, vacuum cleaning, etc) DRY BULK TRUCK PRESSURE BLOWERS Flows m h - Pressures to bar gauge. Vacuum to 500 mbar abs Vertically split cast iron casing Cast or riveted type impellers, statically and dynamically balanced Carbon ring seals to reduce air leakage and improve efficiency Cast aluminum bearing housing for better heat dissipation Oil splash lubricated bearings with constant level oiler to ensure long bearing life Balancing piston on larger models to counteract thrust load on bearings Optimized ratios of impellers vs diffuser diameters and large turning radius of interstage channel for higher efficiencies The Truckstar range has been developed specifically for dry bulk transfer applications on trucks for the cement, fly ash, lime, flour, powders, sugar, plastics pellets, sand grain industries... Flows m h - Pressure to. bar gauge. Vacuum to 500 mbar abs Tri-lobe construction with pulsation control ports for smoother operation Oil splash lubricated bearings and large capacity sumps Double ring feeder and gear retainers for more input torque capability Heavy duty casting ribbed for rigidity and noise attenuation Built-in melting plugs for temperature protection PROCESS BLOWERS VACUUM AIR INJECTION BLOWERS Flows of m h - Vacuum to 00 mbar abs Tri-lobe construction to reduce pulsations, noise level and vibrations Five bearings standard designed for maximum speed and vacuum Helical gears located on the drive side for more input torque capability Oil lubrication and large oil sumps to improve bearing life Self cooling and runs cooler for long service No need for vacuum relief valve. Can operate even with blanked inlet High vacuum and efficient on wet and dry products Flows to 0000 m h - Pressure to.7 bar gauge. Vacuum to 500 mbar abs Tri-lobe construction with pulse control system to reduce pulsations and noise Five bearings standard designed for v-belt or direct drive Oil lubrication at both ends with large sumps Choice of shaft and main seals for gases Wide choice of construction material to meet process requirements 00% oil free gas guaranteed Complete packages including accessories and control system These units can be designed to handle a wide variety of gases. Various materials and sealing designs are available to meet most process requirements and international standards. For North American orders shop online: or call:

47 OIL FREE SCREW COMPRESSORS Industrial gases/vacuum swing absorption Flows to 8500 m h - Pressures to bar gauge and vacuum to 500 mbar abs Single or multi-stage blower systems Air-end manufactured froigh grade cast iron directly connected to an integral gear box Forged steel rotors for constant performance Calculated tolerances between the rotors and the body to optimize efficiency Anti-friction bearings optimized for maximum reliability Mechanically driven oil pump from main shaft with integral oil tank and external oil/air heat exchanger Complete packages including accessories and control system Screw compressors are an optimum solution for applications requiring oilfree gases at higher operating pressures. Typical applications are: Dense phase pneumatic conveying of bulk material in chemical, food and cement industries Desulphurization of combustion gases Ballast pressurization Aeration in sewage treatment ENGINEERING CAPABILITIES Petro chemicals/nitrogen gas circulation Chemical industry/manufacture of hydrogen peroxide/ Stationary air PROCESS SYSTEMS Environment/Waste treatment/biogas recovery For North American orders shop online: or call:

48 Environment/Waste water treatment/biological aeration 4 Chemical industry/manufacture of chemical products/gas compression on hydrogenation loop Please contact BOC Edwards for recommendation of a design to suit your applications that also ensures ease of maintenance and serviceability. For North American orders shop online: or call:

Standard Circulating Pumps

Standard Circulating Pumps Product review Range: 1 1 3Q [ m³/h] Hz - North America 1 3 1 1 1.x1 1.x x x3 x 1 1 Q [ US gpm] >Single-head pumps: Seal-less circulator with flanged connection. Two speed, manually adjustable to match

More information

BARE SHAFT PUMPS AND MOTOR PUMPS

BARE SHAFT PUMPS AND MOTOR PUMPS APPLICATIONS Air Conditioning Heating and ventilation Refrigeration Fire protection Plumbing Water Circulation Transfer and Irrigation Pressure Boosting Process Industries Water Treatment and Supply DESIGN

More information

TD End-Suction Pumps. Operating data Flow rates up to 300 l/sec Head up to 160 metres Temperature 20 0 C to C

TD End-Suction Pumps. Operating data Flow rates up to 300 l/sec Head up to 160 metres Temperature 20 0 C to C TD End-Suction Pumps One of the broadest ranges of pumps available from any British manufacturer, with discharge sizes from mm to 0 mm. Widest choice of materials of construction and options to suit many

More information

MAX FLUID TEMPERATURE

MAX FLUID TEMPERATURE Centrifugal pumps are designed to transfer both corrosive and non-corrosive fluids at maximum hydraulic efficiencies. Centrifugal pumps are not self-priming and must be used in applications where flooded

More information

Standard Circulating Pumps

Standard Circulating Pumps Product review Range: 1 1 3Q [ m³/h] Hz - North America 1 3 1 1 1.x1 1.x x x3 x 1 1 Q [ US gpm] >Single-head pumps: Circulating pumps with flanged connection > Applications: Drinking-water circulation

More information

JVMG* *NSF 61/Annex G Certification and Compliance with State Codes does not apply to JVMG Models

JVMG* *NSF 61/Annex G Certification and Compliance with State Codes does not apply to JVMG Models JVM, JVML SERIES Stainless Steel Construction Closed multi-stage impeller Flow: 4 to 38 GPM Head: to 82 ft. Range of HP: to HP Applications: Commercial booster system, Boiler feed, Jockey, Water Purification,

More information

Close-coupled centrifugal pumps

Close-coupled centrifugal pumps CombiBloc Close-coupled centrifugal pumps CombiBloc CombiBloc is the premier solution for pumping clean thin liquids in a very cost-effective way. The pump is part of Johnson Pump s Combi-system, a modular

More information

Standardised EN 733 centrifugal pumps

Standardised EN 733 centrifugal pumps F Standardised EN 733 centrifugal pumps PERFORMANCE RANGE Flow rate up to l/min (3 m³/h) Head up to 9 m APPLICATION LIMITS Manometric suction lift up to 7 m Liquid temperature between - C and +9 C Ambient

More information

SERIES 1300 Quality Design Features Assure Long, Trouble-Free Service

SERIES 1300 Quality Design Features Assure Long, Trouble-Free Service SERIES Quality Design Features Assure Long, Trouble-Free Service End Suction WIDE RANGE OF APPLICATIONS: Industrial Process Pollution Control General Pumping Spray Systems Deionized Water Waste Water Clear

More information

2CP. Centrifugal twin-impeller pumps

2CP. Centrifugal twin-impeller pumps CP Centrifugal twin-impeller pumps Clean water Domestic use Civil use Industrial use PERFORMANCE RANGE Flow rate up to l/min (7 m³/h) Head up to m APPLICATION LIMITS Manometric suction lift up to 7 m Liquid

More information

UPGRADE PROGRAM. V250 Series Pumps vs V301 Series Pumps. Technical Memo

UPGRADE PROGRAM. V250 Series Pumps vs V301 Series Pumps. Technical Memo UPGRADE PROGRAM V250 Series Pumps vs V301 Series Pumps Technical Memo INDEX Outline drawings ISO100 3 Outline Drawing CFF6 5 Technical Specification 7 Notes 8 Accessories 8 Controller comparison 9 Outline

More information

Assembly and Maintenance

Assembly and Maintenance Assembly and Maintenance Assembly and Maintenance Test Pumps Pressure Test Pumps Tests all types of installations such as heating, compressed air and refrigeration systems, oil installations, fire lines

More information

Lenntech BMP GRUNDFOS DATA BOOKLET. High-pressure piston pumps 50/60 Hz

Lenntech BMP GRUNDFOS DATA BOOKLET. High-pressure piston pumps 50/60 Hz Lenntech GRUNDFOS DATA BOOKLET BMP High-pressure piston pumps 50/60 Hz Contents Product data Introduction Page 3 Features and benefits Page 3 Applications Page 3 Pumped liquids Page 3 key Page 4 Motor

More information

Drawing on 40 years of

Drawing on 40 years of Systems Drawing on 40 years of blower and manufacturing experience, Republic Blower Systems are designed to outperform any blower on the market. Providing the ideal combination of powerful air movement,

More information

Introduction. Available materials. Aluminum Carbon Steel Stainless Steel Ductile Iron Special Materials on Application

Introduction. Available materials. Aluminum Carbon Steel Stainless Steel Ductile Iron Special Materials on Application VALVES & CONTROLS VAREC 00B/00B The Varec 00B/00B protects tanks from damage or deformation, and minimizes emissions to the environment, as well as loss of product due to evaporation. Introduction 00B

More information

L P Linn-Pumpen GmbH. Submersible Vertical Electric pumps. SVI Series. with high efficiency PLM motors. SVI Series MARKET SECTORS INDUSTRIAL, CIVIL.

L P Linn-Pumpen GmbH. Submersible Vertical Electric pumps. SVI Series. with high efficiency PLM motors. SVI Series MARKET SECTORS INDUSTRIAL, CIVIL. Submersible Vertical Electric pumps with high efficiency PLM motors MARKET SECTORS INDUSTRIAL, CIVIL. APPLICATIONS Pumping of coolants, lubrificants and condensate. Machine tools, welders, engine test

More information

SUBMERSIBLE PUMPS SEWAGE RANGE

SUBMERSIBLE PUMPS SEWAGE RANGE OPERATING LIMITS Flow rates up to: 00 m /h Head up to: 0 m CL Liquid temperature range: + to 0 C* Density of liquid:.0 max. ph of liquid: - Max. immersion depth: 0 m Max. particle size: Ø 0-0 mm ND discharge

More information

Easy Flow Indicator Magnetisch-Induktiver Durchflussmesser. Type 8024 For Insertion Fittings. Analog Flow Rate Indicator, 1/2"-16"; P=87 PSI

Easy Flow Indicator Magnetisch-Induktiver Durchflussmesser. Type 8024 For Insertion Fittings. Analog Flow Rate Indicator, 1/2-16; P=87 PSI Analog Flow Rate Indicator, 1/2"-16"; P=87 PSI Advantages / Benefits Reduced costs of ownership up to 6% Economic integration in pipe systems without any additional piping Shows flow rate with a clear,

More information

Electric Actuated Ball Valves 2-way Stainless Steel, Full Port 1/4 to 2 NPT

Electric Actuated Ball Valves 2-way Stainless Steel, Full Port 1/4 to 2 NPT 1/4 to 2 NPT Features Direct mount ISO5211 Full Port 316 stainless steel ball valve 1000 PSI working pressure at 100 F (38 C) Highly visual dome style valve position indicator Rugged aluminum Type 4X weatherproof

More information

VAREC 2010B/2020B PRESSURE AND VACUUM RELIEF VALVES

VAREC 2010B/2020B PRESSURE AND VACUUM RELIEF VALVES VAREC 0B/B PRESSURE AND VACUUM RELIEF VALVES Weight-loaded relief valves that protect tanks from damage or deformation, minimize emissions to the environment and loss of product due to evaporation FEATURES

More information

Stainless Steel Submersible Pumps DATA BOOKLET. ISO 9001 Company. 60 Hz. Pumping Solution

Stainless Steel Submersible Pumps DATA BOOKLET. ISO 9001 Company. 60 Hz. Pumping Solution Stainless Steel Submersible Pumps DATA BOOKET ISO Company Pumping Solution Hz Photographs of a few Manufacturing Units Contents Stainless steel submersible bore well pumps Product data Introduction Operating

More information

CR, CRN high pressure

CR, CRN high pressure GRUNDFOS DATA BOOKLET CR, CRN high pressure Vertical multistage centrifugal pumps 5/6 Hz Contents Product Data Performance range 3 Product range 4 Applications 4 CRNE 1 and 3 HS 5 CRN 5, 1, 15, SF 6 x

More information

UPGRADE PROGRAM. V70 Series Pumps vs V81T Series Pumps

UPGRADE PROGRAM. V70 Series Pumps vs V81T Series Pumps VARIAN vacuum technologies UPGRADE PROGRAM V70 Series Pumps vs V81T Series Pumps Technical Memo Technical Memo - 1 - V70 series vs V81-T INDEX Outline drawings ISO63 3 Outline drawings CF2-¾ 4 Outline

More information

21023, 21025, 2/2 Direct solenoid actuated poppet valves

21023, 21025, 2/2 Direct solenoid actuated poppet valves 03, 05, / > > Port size: G/4, G/ > > Working from 0 bar up > > Suitable for mediumhigh vacuum down to.33 0 - mbar l/s > > Compact design > > Valves and solenoids are ATEX approved. Additional international

More information

4" MULTISTAGE CENTRIFUGAL SUBMERSED PUMPS COMPLETE WITH MOTOR

4 MULTISTAGE CENTRIFUGAL SUBMERSED PUMPS COMPLETE WITH MOTOR NOCCHI SCM 4 PLUS Maximum rigidity and resistance to water hammer, Strong resistance to the abrasive action of sand, Excellent hydraulic efficiency SCM 4 PLUS submersible pumps consist of a multi-stage

More information

Submersible Pumps. Pumping Solution. 50 Hz

Submersible Pumps. Pumping Solution. 50 Hz Submersible Pumps Pumping Solution 0 Hz INTRODUCTION Submersible bore well pumps for (DN 0 mm), (DN 0 mm), (DN 0 mm), (DN 00mm), (DN 0 mm) and (DN 00 mm) wells. Sized for connection to the motor according

More information

ASTRO 2 CIRCULATORS. ASTRO 2 3-Speed Circulators (except Astro 286):

ASTRO 2 CIRCULATORS. ASTRO 2 3-Speed Circulators (except Astro 286): DATE: January 30, 015 DATE: January 5, 014 ASTRO 3-Speed Circulators (except Astro 86): ASTRO CIRCULATORS IRON BODY CONSTRUCTION (Includes Check Valve) Model No. Part No. Connection List Price Wt.ea.lbs.

More information

Atlas Copco Airmotors

Atlas Copco Airmotors Atlas Copco Airmotors Atlas Copco air motors Leading the industry in development and innovation. Offering a comprehensive range of standard air motors. A premier supplier of air motors engineered to meet

More information

The VARIO Chemistry-pumping units with adaptive vacuum control

The VARIO Chemistry-pumping units with adaptive vacuum control The VARIO Chemistry-pumping units with adaptive vacuum control Self-optimizing vacuum for productivity and efficiency Optimize laboratory processes with VACUUBRAND VARIO technology Vacuum applications

More information

Compact Bellows Pumps

Compact Bellows Pumps Compact Bellows Pumps Compact Bellows Metering Pumps were specifically designed for metering applications requiring low discharge pressures. Compact pumps have been successfully applied in photo, X-ray

More information

High Voltage Induction Motors. 21-MII Series. New High Efficiency Design for High Capacity Applications Up to 3,550 kw (4,750 HP)

High Voltage Induction Motors. 21-MII Series. New High Efficiency Design for High Capacity Applications Up to 3,550 kw (4,750 HP) High Voltage Induction Motors -MII Series New High Efficiency Design for High Capacity Applications Up to,0 kw (,0 HP) MII Series: Combining over 00 years of experience with innovative new technology makes

More information

Oil Free Scroll. Air Compressors

Oil Free Scroll. Air Compressors Oil Free Scroll Air Compressors History of HITACHI Air Technology 1910 1930 1950 1970 1980 1911: 75kW Reciprocating First Compressor in Japan 1977: Smallest 5.5kW Oil Injected Rotary Screw 1976: Oil Injected

More information

Thermal Diffusivity Instruments DLF-2 with EM-1600

Thermal Diffusivity Instruments DLF-2 with EM-1600 Thermal Diffusivity Instruments DLF-2 with EM-1600 Site Preparation Guide Revision A Issued February 2017 Table of Contents Table of Contents... 1 Ideal Setup... 2-3 System Components... 3 Instrument Measurements...

More information

Shaft Seal. Accessories

Shaft Seal. Accessories Type series booklet Hz.5/- G Standardized Pumps Fields of Application Water supply Sprinkling Irrigation Drainage Air-conditioning Drinking water Waste water Cooling water Fluid Pure liquids not chemically

More information

Standard Bellows Metering Pumps

Standard Bellows Metering Pumps Standard Bellows Metering Pumps Bellows Metering Pumps operate on a positive displacement principle. Pumps are designed to displace both corrosive and noncorrosive fluids. Accurate to ± 0.5% from stroke

More information

L P Linn-Pumpen GmbH. Electric-gear-pumps series FKM

L P Linn-Pumpen GmbH. Electric-gear-pumps series FKM Electric-gear-pumps series FKM Construction Self-priming electric-gear-pumps, bellhousing with foot-flange, pump-casing in cast iron. Gear-pumps series FKM with motor-power up to 1,5. Suction- and -ports

More information

09LD/GD. Air-Cooled Condensers/Air-Cooled Fluid Coolers. Nominal cooling capacity kw 09LD/GD 09GD

09LD/GD. Air-Cooled Condensers/Air-Cooled Fluid Coolers. Nominal cooling capacity kw 09LD/GD 09GD Air-Cooled Condensers/Air-Cooled Fluid Coolers 09LD/GD 09GD 09LD/GD Nominal cooling capacity 281-987 kw The 09LD air-cooled condensers are designed for refrigeration plants where a halogenated hydrocarbon,

More information

LCC Pump Series - Wear Resistant, High Performance Slurry Pumps

LCC Pump Series - Wear Resistant, High Performance Slurry Pumps LCC Pump Series - Wear Resistant, High Performance Slurry Pumps 02 LCC Pump Series Solutions for the most Abrasive and Corrosive Slurry Applications With High Performance Wear Resistance, the GIW Minerals

More information

Atlas Copco air motors

Atlas Copco air motors Atlas Copco air motors Atlas Copco air motors Leading the industry in development and innovation. Offering a comprehensive range of standard air motors. A premier supplier of air motors engineered to meet

More information

ZMD ZMDV. AXIALLY SPLIT, ONE-STAGE, BETWEEN-BEARINGS PUMPS 50/60 Hz. High reliability and efficiency. Wide range of material options

ZMD ZMDV. AXIALLY SPLIT, ONE-STAGE, BETWEEN-BEARINGS PUMPS 50/60 Hz. High reliability and efficiency. Wide range of material options AXIALLY SPLIT, ONE-STAGE, BETWEEN-BEARINGS PUMPS 0/ Hz ZMD ZMDV High reliability and efficiency Wide range of material options Excellent suction capability due to low NPSH Simple installation and maintenance

More information

FOX-50 Heat Flow Meter

FOX-50 Heat Flow Meter FOX-50 Heat Flow Meter Site Preparation Guide Revision A Issued June 2016 Page 1 Table of Contents Table of Contents... 1 Ideal Setup... 2 System Components... 3 Instrument Measurements... 4 Utility Requirements...

More information

NDP-50 Series Specifications

NDP-50 Series Specifications NDP-50 Series Specifications Port Dimensions Intake & discharge connection: Polypropylene (PPG) 2 50mm DIN DN80 PN10 Kynar (PVDF) 2 50mm DIN DN80 PN10 Aluminum (ADC-12) 2 50mm DIN DN80 PN10 (with tapped

More information

P30-2. Overview. Pressure Transmitter Datasheet. *High Quality* 3 Years Warranty. At a Glance. Function. Application

P30-2. Overview. Pressure Transmitter Datasheet. *High Quality* 3 Years Warranty. At a Glance. Function. Application P30-2 Pressure Transmitter Datasheet At a Glance *High Quality* 3 Years Warranty Premium Pressure Transmitter for gauge and pressure measurement with 3 years warranty High repeatability and long-term stability

More information

Data sheet: Wilo-Stratos 40/1-8

Data sheet: Wilo-Stratos 40/1-8 Data sheet: Wilo-Stratos 4/1-8 Pump curves 1 2 v 3 4 DN4 m/s,5 1, 1,5 2, 2,5 DN5 H/m Wilo-Stratos 4/1-8 p/kpa Wilo-Stratos 5/1-8 48 1 /min - 1 V 1~23 V - DN 4 / DN 5 8 8 P 1/W n= const 6 383 1 /min - 8

More information

FEATURES APPLICATIONS OPERATING DATA MATERIALS OF CONSTRUCTION. Flood control

FEATURES APPLICATIONS OPERATING DATA MATERIALS OF CONSTRUCTION. Flood control APPLICATIONS FEATURES Flood control Irrigation Land drainage Pollution control Industry Water refineries Water parks Design OPERATING DATA Capacity:...up to.000 m/h Head:...up to m Max. water temperature:...0

More information

Model VDL 115 Vacuum drying chambers for flammable solvents

Model VDL 115 Vacuum drying chambers for flammable solvents Model VDL 115 Vacuum drying chambers for flammable solvents A BINDER safety vacuum drying oven of the VDL series ensures maximum safety when drying organic solvents standard with TÜV/GS. The inner chamber

More information

Electromechanical pressure switches

Electromechanical pressure switches Presentation Electromechanical pressure switches For control circuits, types ACW and ADW Presentation Pressure switches type ACW and ADW are switches for control circuits, with an adjustable differential.

More information

2-PORT SEAT VALVES PN16 WITH FLANGED CONNECTIONS STAZ-16, STBZ-16, STCZ-52 DATASHEET

2-PORT SEAT VALVES PN16 WITH FLANGED CONNECTIONS STAZ-16, STBZ-16, STCZ-52 DATASHEET -PORT SEAT VALVES PN WITH FLANGED CONNECTIONS STAZ-, STBZ-, STCZ- DATASHEET In boiler, district heating and refrigeration plants, cooling towers, heating groups, in ventilation and air-handling units as

More information

ASTRO CIRCULATORS. IRON BODY CONSTRUCTION Model No. Part No. Connection List Price Wt.ea.lbs. ASTRO

ASTRO CIRCULATORS. IRON BODY CONSTRUCTION Model No. Part No. Connection List Price Wt.ea.lbs. ASTRO ASTRO CIRCULATORS ASTRO 3 Speed: IRON BODY CONSTRUCTION Model No. Part No. Connection List Price Wt.ea.lbs. ASTRO-30-3 110123-305 Replaced by 110223-305 (Astro 2) ASTRO-50-3 110123-307 Replaced by 110223-307

More information

Motivair MLC-SC Air-Cooled Scroll Chillers Tons

Motivair MLC-SC Air-Cooled Scroll Chillers Tons INNOVATE DESIGN APPLY www.motivaircorp.com Motivair MLC-SC Air-Cooled Scroll Chillers 100 285 Tons OUR BUSINESS IS COOLING YOURS. When commercial grade isn t enough Businesses who function in today s advanced

More information

Rosemount 1595 Conditioning Orifice Plate

Rosemount 1595 Conditioning Orifice Plate Reference Manual Rosemount 1595 Conditioning Orifice Plate www.rosemount.com Reference Manual 00809-0100-4828, Rev BA Rosemount 1595 Rosemount 1595 Conditioning Orifice Plate NOTICE Read this manual before

More information

8 Submersible Motors Hi-Temp 75

8 Submersible Motors Hi-Temp 75 Applications These motors are built for dependable operation in vertical 8 diameter or larger wells, in applications with higher temperature, higher thrust or low flow. Basic Features Able to operate in

More information

This is an economic model, especially suitable for instruments with ¼ port connection. Not detachable to repair.

This is an economic model, especially suitable for instruments with ¼ port connection. Not detachable to repair. Diaphragm seals - Stainless steel d. seals ¼ - PVC diaphragm seals ¼ - Stainless steel d. seals ½ - PVC diaphragm seals ½ - Easy-to-clean diaphragm seals - High pressure diaphragm seals - Low pressure

More information

Immersion Temperature Sensors

Immersion Temperature Sensors 1 782 1782P01 Symaro Immersion Temperature Sensors QAE2164 QAE2174 Active sensors for acquiring the water temperature in pipes and tanks Operating voltage AC 24 V or DC 13535 V Signal output DC 010 V or

More information

Flow VA 500/

Flow VA 500/ VA 500/ 520 Verbrauch 79 What are the advantages of the flow measuring technology of CS Instruments? 1) 500 is mounted by means of a standard 1/2 ball valve. During mounting and dismounting the safety

More information

Vane wheel probe BFA25 for flow measurement of gases and liquids with integrated, configurable transducer UFA in Ex-d housing

Vane wheel probe BFA25 for flow measurement of gases and liquids with integrated, configurable transducer UFA in Ex-d housing Vane wheel probe BFA25 for flow measurement of gases and liquids with egrated, configurable transducer UFA in Ex-d housing Drawing 5 Vane wheel flow probe BFA25 (Dimensions see Page 3) Measurable variables

More information

DDDM 45 (40-60 TPH) DDDM 60 ( TPH) COLD AGGREGATE FEEDER. Auxiliary belt No. of bins. Gathering conveyor reduction gear

DDDM 45 (40-60 TPH) DDDM 60 ( TPH) COLD AGGREGATE FEEDER. Auxiliary belt No. of bins. Gathering conveyor reduction gear I TECHNICAL SPECIFICATIONS ROAD BUILDING DDDM 45 (40-60 TPH) DOUBLE DRUM ASPHALT PLANT - DDDM 50 (60-90 TPH) DDDM 60 (90-120 TPH) COLD AGGREGATE FEEDER Stationary four bin cold aggregate feeder unit is

More information

NEW NEW. Diaphragm agm Pumps MPC for Chemical Applications MPC 301 E. MPR 060 E with power pack

NEW NEW. Diaphragm agm Pumps MPC for Chemical Applications MPC 301 E. MPR 060 E with power pack Diaphragm agm Pumps MPC for Chemical Applications The diaphragm pumps for chemical applications -Type MPC- are resistant to aggressive solvents and acidic vapors typically used in laboratory processes.

More information

Printer specifications

Printer specifications STUDIO SYSTEM Printer specifications The printer was designed from the ground-up for simple installation and use. Its process is similar to the safest, most widely used 3D printing process Fused Filament

More information

edwardsvacuum.com nxds DRY SCROLL PUMPS

edwardsvacuum.com nxds DRY SCROLL PUMPS edwardsvacuum.com nxds DRY SCROLL PUMPS THE PARTNER OF CHOICE Edwards is a world leader in the design, technology and manufacture of vacuum pumps with over 95 years history and more than 75 years manufacturing

More information

HANKIA. DSV type. Single stage,vertical Axially split case double suction pump

HANKIA. DSV type. Single stage,vertical Axially split case double suction pump DSV type Single stage,vertical Axially split case double suction pump High efficiency and low pulsation Wind performance range with up to 280m head Stable service and low maintenance Heavy duty design

More information

8 Submersible Motors Standard

8 Submersible Motors Standard Applications These motors are built for dependable operation in vertical 8 diameter or larger water wells. Basic Features Double Flanged NEMA mounting design Stainless steel splined shaft StatorShield

More information

Flow. Flow. N/en

Flow. Flow. N/en / poppet valves electromagnetic actuated, directly controlled G /4 or /4 NPT Working from 0 bar up Short switching times Suited for fine vacuum down to, 0 - mbar For a.c. solenoid systems with integrated

More information

The 5400A Series, Group D, end-of-line flame arrester is designed to prevent the propagation of flames into a storage vessel.

The 5400A Series, Group D, end-of-line flame arrester is designed to prevent the propagation of flames into a storage vessel. Varec 00A Series The 00A Series, Group D, end-of-line flame arrester is designed to prevent the propagation of flames into a storage vessel. Introduction Varec s have been the industry standard for over

More information

MOLLIER DIAGRAM CAN BE IMPROVED!

MOLLIER DIAGRAM CAN BE IMPROVED! MOLLIER DIAGRAM CAN BE IMPROVED! IMPROVED BASIC COOLING CIRCUIT PERFORMANCE EFFICIENCY USING AN ECONOMISER Eng. Jonny Malachi, VP Operations, Mashav Refrigeration and Air Conditioning Engineering Ltd.

More information

Safety valves. Safety valves Safety valves for heating, cooling and solar systems, DN 15 DN 50

Safety valves. Safety valves Safety valves for heating, cooling and solar systems, DN 15 DN 50 Safety valves Safety valves Safety valves for heating, cooling and solar systems, DN 15 DN 50 IMI PNEUMATEX / Accessories and Service / Safety valves Safety valves For the safeguarding of thermostatically

More information

Sputtering Sensor ADVANTAGES

Sputtering Sensor ADVANTAGES The INFICON is specifically designed for use in any sputtering process. The sensor body and cooling tubes are gold plated beryllium copper for maximum cooling efficiency in the sputtering environment.

More information

Butterfly Control Valve. DMK/6 Series

Butterfly Control Valve. DMK/6 Series Butterfly Control Valve DMK/6 Series UL Listed for US and Canada UL 842 and ULc C125 & C842 File # MH 18741 Models DMK 707/6 (3/4 NPT) DMK 710/6 (1 NPT) DMK 712/6 (1 1/4 NPT) DMK 715/6 (1 1/2 NPT) DMK

More information

Mission Critical Facilities & Technology Conference November 3, 2011 Cooling 101. Nick Gangemi Regional Sales Manager Data Aire

Mission Critical Facilities & Technology Conference November 3, 2011 Cooling 101. Nick Gangemi Regional Sales Manager Data Aire Mission Critical Facilities & Technology Conference November 3, 2011 Cooling 101 Nick Gangemi Regional Sales Manager Data Aire Agenda Exactly what are we talking about ASHRAE TC 9.9 Design best practices

More information

FLS F3.00 PADDLEWHEEL FLOW SENSOR APPLICATIONS MAIN FEATURES

FLS F3.00 PADDLEWHEEL FLOW SENSOR APPLICATIONS MAIN FEATURES FLS F3.00 PADDLEWHEEL FLOW SENSOR APPLICATIONS The simple and reliable paddlewheel flow sensor type F3.00 is designed for use with every kind of solid-free liquids. The sensor can measure flow from 0.15

More information

E Q U I C I E N H Y G E U R O P E A N

E Q U I C I E N H Y G E U R O P E A N PRESSURE AND LEVEL TRANSMITTERS ALL STAINLESS SERIES 8000-SAN OUTPUT 4-20 ma / 2-WIRE ZERO AND SPAN ADJUSTABLE ALL FORMS OF HYGIENIC/ SANITARY CONNECTIONS AVAILABLE VERY STRONG FLUSH MOUNTING DIAPHRAGM

More information

Data sheet: Wilo-Stratos 50/1-9

Data sheet: Wilo-Stratos 50/1-9 Data sheet: Wilo-Stratos 5/1-9 Pump curves H/m 2 5 1 15 2 1 v 1 2 3 1 41 1 /min-1 V 8 3714 1 /min-9 V 3329 1 /min-8 V 6 4 57 1 /min-6 V 2 4 6 P 1/W n= const 4 8 V 2 H/m 2943 1 /min-7 V 2171 1 /min-5 V

More information

Data sheet: Wilo-Stratos 50/1-10

Data sheet: Wilo-Stratos 50/1-10 Data sheet: Wilo-Stratos 5/1-1 Pump curves v,4,8 1,2 1,6 2, 2,4DN 4 m/s,4,8 1,2 DN 5 H/m p/kpa Wilo-Stratos 4/1-1 445 1 /min - 1 V Wilo-Stratos 5/1-1 1 1~23 V - DN 4, DN 5 8 P 1/W n= const 6 314 1 /min

More information

NSF/ANSI 61 Drinking Water System Components - Health Effects

NSF/ANSI 61 Drinking Water System Components - Health Effects Page 1 of 7 The Public Health and Safety Organization NSF Product and Service Listings These NSF Official Listings are current as of Monday, September 19, 2016 at 12:15 a.m. Eastern Time. Please contact

More information

Technical Specification _5.0. Concertor N/EA/DP

Technical Specification _5.0. Concertor N/EA/DP Technical Specification 886_. Concertor N/EA/DP Table of Contents Table of Contents System Description.... System overview..... Concertor N..... Concertor EA..... Concertor DP... Product Description...6.

More information

PUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps...

PUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps... PUMPS FOR INDUSTRY CONTENTS: The Vertical Pump Specialists Introduction & User List Product Overview Vertical Process Pumps... Vertical Sewage Pumps... Series 700 Vertical Sump Pumps... Series 800 Vertical

More information

MPC Air-Cooled Chillers MPC-FC Free-Cooling Chillers

MPC Air-Cooled Chillers MPC-FC Free-Cooling Chillers INNOVATE DESIGN APPLY www.motivaircorp.com MPC Air-Cooled Chillers MPC-FC Free-Cooling Chillers ½ - 100 Tons OUR BUSINESS IS COOLING YOURS. When commercial grade isn t enough Motivair is a world-class

More information

Data sheet: Wilo-Stratos 30/1-8

Data sheet: Wilo-Stratos 30/1-8 Data sheet: Wilo-Stratos 3/1-8 Pump curves 7 337 1 /min - 9 V 6 34 1 /min - 8 V 5 271 4 1 /min - 7 V 239 1 /min - 6 V 3 26 1 /min - 5 V 2 173 1 /min - 4 V 14 1 1 /min - 3 V 2 4 6 8,5 1, 1,5 2, 2,5 Q/l/s

More information

MLC Air-Cooled Chillers MLC-FC Free-Cooling Chillers MLC-AD Adiabatic Chillers

MLC Air-Cooled Chillers MLC-FC Free-Cooling Chillers MLC-AD Adiabatic Chillers INNOVATE DESIGN APPLY www.motivaircorp.com MLC Air-Cooled Chillers MLC-FC Free-Cooling Chillers MLC-AD Adiabatic Chillers 60-500 Tons OUR BUSINESS IS COOLING YOURS TM When commercial grade isn t enough

More information

1.5 to 5 Tons INDOOR COILS C35. Upflow - Cased and Uncased PRODUCT SPECIFICATIONS C A - 2 F - 1 MODEL NUMBER IDENTIFICATION FEATURES

1.5 to 5 Tons INDOOR COILS C35. Upflow - Cased and Uncased PRODUCT SPECIFICATIONS C A - 2 F - 1 MODEL NUMBER IDENTIFICATION FEATURES INDOOR COILS C35 PRODUCT SPECIFICATIONS Upflow - Cased and Uncased Bulletin No. 20666 February 208 Supersedes November 206.5 to 5 Tons MODEL NUMBER IDENTIFICATION Unit Type C = Indoor Coil = Upflow Series

More information

DIP. Spare parts list. Centrifugal pumps 25, 25-US, 35, 35-US, 65, 65-US Atlas Copco Construction Tools AB No c

DIP. Spare parts list. Centrifugal pumps 25, 25-US, 35, 35-US, 65, 65-US Atlas Copco Construction Tools AB No c DIP 5, 5US, 35, 35US, 65, 65US Spare parts list Centrifugal pumps 0 Atlas Copco Construction Tools AB No. 9800 5 0c 003 DIP 5, 5US, 35, 35US, 65, 65US Contents Contents General information................................................................

More information

Adjustable, Dirt Tolerant Venturi Vacuum Pumps

Adjustable, Dirt Tolerant Venturi Vacuum Pumps Adjustable, Dirt Tolerant Venturi Vacuum Pumps VDF Series VDF-37-ST8B picks and places refrac bricks used to line refractory ovens. Standard Pump: The VDF Series is a unique Vaccon innovation that places

More information

LS 5000 series Vibration Level Switch for liquids

LS 5000 series Vibration Level Switch for liquids Vibration Level Switch for liquids Set-up without adjustment Integrated fault monitoring Unaffected by product variations in density, conductivity, dielectric constant or viscosity Insensitive to foam,

More information

E SERIES CIRCULATORS

E SERIES CIRCULATORS E SERIES CIRCULATORS CAST IRON BODY CONSTRUCTION BRONZE BODY CONSTRUCTION Part No. Part No. Model 120V Motor 240V Motor List Price Wt (lbs) Model 120V Motor 240V Motor List Price Wt (lbs) E7 180200-643

More information

Type. Facts. 441, 442 Full nozzle DIN. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. Metric Units LWN E

Type. Facts. 441, 442 Full nozzle DIN. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. Metric Units LWN E Type 441, 442 DIN Flanged Safety Relief Valves spring loaded Metric Units Facts The-Safety-Valve.com LWN 468.01-E DIN, ANSI 40 Cap H2 19 Lock nut 18 Adjusting screw with bushing 16 Upper spring plate 12

More information

Air Moving Solutions. axipal adjustable pitch airfoil fans

Air Moving Solutions. axipal adjustable pitch airfoil fans Air Moving Solutions. axipal adjustable pitch airfoil fans ATAD ATAB CATALOG AX210 December 2012 AdjustablePitch Models ATAD ATAB Model ATAD Arrangement 4 - Direct Drive The ATAD Adjustable Pitch Airfoil

More information

KF ADAPTORS AND BELLOWS

KF ADAPTORS AND BELLOWS GENERAL INFORMATION Various adaptors and bellows are used for glass pipelines to form joints with other pipelines or with tubes. Especially for forming joints with fixed pipelines or in certain cases between

More information

Installation Site Survey Walchem Web-Based Controllers April 27, 2004

Installation Site Survey Walchem Web-Based Controllers April 27, 2004 Installation Site Survey Walchem Web-Based Controllers April 27, 2004 General Installation Checklist Select a location for the controller(s) to be installed. The following criteria must be met: Vibration

More information

VAREC 5000/5010 SERIES FLAME ARRESTERS

VAREC 5000/5010 SERIES FLAME ARRESTERS VAREC 000/00 SERIES FLAME ARRESTERS Group D end-of-line flame arresters with a unique extensible bank frame designed to stop the propagation of flame from external sources FEATURES 00 SERIES - HORIZONTAL

More information

Magnetic drive pumps M35 to M200 catalogue

Magnetic drive pumps M35 to M200 catalogue publication date 0/07/08 Magnetic drive pumps M35 to M00 catalogue Presentation of the range M00 Curves M35 M10 Applications : surface treatment, transfer, pumping of chemicals, water treatment, paper

More information

Flow. Order number VA 550. Order no. VA 570. Further accessories A_...M_

Flow. Order number VA 550. Order no. VA 570. Further accessories A_...M_ Order number VA 550 housing High-pressure rig for VA 550 recoended for mounting from 10 to 100 bar Order no. 0695 0550 A_...M_ 0530 1155 Order no. VA 570 Order no. 0695 0570 0695 0571 0695 0572 0695 0573

More information

IT COOLING EVAPORATIVE COOLING SYSTEM. 2 STAGE INDIRECT ADIABATIC COOLING SYSTEM FOR LARGE DATA CENTERS FROM 80 TO 320 kw

IT COOLING EVAPORATIVE COOLING SYSTEM. 2 STAGE INDIRECT ADIABATIC COOLING SYSTEM FOR LARGE DATA CENTERS FROM 80 TO 320 kw IT COOLING EVAPORATIVE COOLING SYSTEM 2 STAGE INDIRECT ADIABATIC COOLING SYSTEM FOR LARGE DATA CENTERS FROM 8 TO 3 kw IT COOLING EVAPORATIVE COOLING SYSTEM ADIABATIC COOLING FOR HIGH EFFICIENCY - Variable

More information

A Data Center Heat Removal System That Saves... 80% Discover Inertech s Award-winning Data Center Heat Removal System

A Data Center Heat Removal System That Saves... 80% Discover Inertech s Award-winning Data Center Heat Removal System A Data Center Heat Removal System That Saves... Infrastructure Power Water up to 40% up to 80% up to 85% Discover Inertech s Award-winning Data Center Heat Removal System A Cool Solution; A Breakthrough

More information

Interface I-300 / I-300 Pro Technical data sheet

Interface I-300 / I-300 Pro Technical data sheet Interface I-300 / I-300 Pro Technical data sheet The Interface I-300 or I-300 Pro are the central control unit for all process parameters of a Rotavapor R-300 system: rotation speed, temperature (heating

More information

Slim duct (AMTTTFNLDEH ) Indoor units

Slim duct (AMTTTFNLDEH ) Indoor units Slim duct (AMTTTFNLDEH ) Slim duct. Specifications 1) Technical specifications Model AM22FNLDEH AM28FNLDEH AMFNLDEH AM4FNLDEH AMFNLDEH Power Supply Ø, #, V, Hz 1,2,22-24, 1,2,22-24, 1,2,22-24, 1,2,22-24,

More information

J&M Fluidics, Inc. Company Product Overview

J&M Fluidics, Inc. Company Product Overview It s All about Building a Better Product for Our Clients! J&M Fluidics, Inc. Company Product Overview J&M Fluidics, Manufacturer of Air & Water-Cooled Process Chillers. Located in Telford, Pennsylvania

More information

Cool Drawer Dual Sensor

Cool Drawer Dual Sensor The Cool Drawer Dual Sensor is designed for use in critical processes where it is desirable to have a second crystal in the vacuum chamber. Water cooled, cast stainless steel sensor body, two Cool Drawer

More information

Application The DA03 serves as indicator of differential. Follow mounting instructions in accordance to application.

Application The DA03 serves as indicator of differential. Follow mounting instructions in accordance to application. DA03 Differential Pressure Gauge / Differential Pressure Gauge and Switch Models for Assignment in Explosion-hazardous Areas per Directive 94/9/EC (ATEX) Application The DA03 serves as indicator of differential

More information

Denton Vacuum Phoenix 400 Continuous In-Line Sputtering Deposition System General Specifications

Denton Vacuum Phoenix 400 Continuous In-Line Sputtering Deposition System General Specifications Phoenix 400 Continuous In-Line Sputtering Deposition System s Phoenix 400X System Overview Denton Vacuum s Phoenix 400X Continuous In-Line Sputtering system provides users optimal uniform coating thicknesses

More information

Asynchronous motors. 5/48 Permissible combinations of mechanical designs for 1PL6 motors,

Asynchronous motors. 5/48 Permissible combinations of mechanical designs for 1PL6 motors, Asynchronous motors 5 Asynchronous motors 5/2 Type overview and rated data 5/4 Technical definitions 5/4 Encoder systems 5/5 1PH7 motors 5/5 1PH7 motors, forced ventilation 5/32 Permissible combinations

More information