Flow Measurement. SITRANS F US Clamp-on. SITRANS FUE1010 (Energy) 4/317. Overview

Transcription

1 Siemens AG 2010 Flow Measurement Overview Application FUE1010 is ideally suited to thermal energy / power industry applications, including: hilled water sub-metering Hot water sub-metering ondenser water Glycol Thermal storage Lake source cooling SITRANS FUE1010 is a highly accurate clamp-on non-intrusive ultrasonic flow transmitter for revenue grade thermal energy sub-metering and energy efficiency distribution monitoring, with a real time coefficient of performance (OP) for HVA systems. SITRANS FUE1010 is available in single and dual channel or dual path configurations, with your choice of IP65 (NEMA X) dedicated wall mount or IP0 (NEMA 1) portable enclosures. Benefits Measures energy rate and total consumption with highest accuracy available Accurately measures at both low flow rates and low differential temperatures Easy installation; no need to cut pipe or stop flow Minimal maintenance; external sensors do not require periodic cleaning No moving parts to foul or wear No pressure drop or energy loss Wide turn-down ratio hoice of single or dual channel / dual path or dual mode operation: - Dual channel operation reduces the cost for the system on a per channel measurement basis and permits measuring hot and chilled water lines at the same time - Dual path capability insures high flow measurement accuracy on installations with less than desirable piping runs Ability to operate in either Wide-Beam Transit-time or reflexor (Doppler) mode for applications with high aeration eromatic Path automatically sets zero without stopping flow and reduces zero drift, even at low flow Design FUE1010 is available in three configurations: IP65 (NEMA X) Enclosure constructed of fiberglass reinforced polyester with stainless steel hardware and polyester keypad - Single channel - Dual channel / dual path IP0 (NEMA 1) Portable Impact Resistant Enclosure constructed of mineral reinforced copolymer polypropylene - Dual channel / dual path Function Flow transmitter has an integral 33 button keypad and large (128 x 20 pixel) graphic display visible up to 12 m (0 ft) away -wire 1000 Ω platinum RTD s for supply and return temperature measurements are precision matched to within 0.01 (0.02 F) Temperature is factory calibrated with built-in field calibrator. Built-in energy/btu mode Detection of aeration and cavitation caused by worn or damaged impellers, misaligned shafts, etc. Reverse flow and empty pipe detection hiller efficiency analysis: accepts an independent analog input representing kw usage for calculation of the following functions which can be selected for data logging or output purposes: - ooling load (kw/ton) - oefficient of performance (OP) - Energy efficiency ratio (EER) Optional current inputs Digital communication options: - MODBUS / Metasys N2 (IP65 (NEMA X) only) - RS232 Serial digital port (standard) eromatic Path automatically sets zero Bi-directional flow operation 1 MByte data logger with both site and data logger storage English, spanish, german, italian and french language options Siemens FI /317

2 Flow Measurement Siemens AG 2010 Technical specifications Input Flow range Flow sensitivity 0 12 m/s (0 0 ft/s), bi-directional m/s (0.001 ft/s) Pipe size 6. mm 9.1 m ( ) Inputs per channel Output Standard outputs Optional outputs Accuracy Accuracy Batch repeatability Rated operation conditions Degree of protection Liquid temperature Standard Optional Sensor temperature Standard Optional Ambient temperature Design Dimensions Weight Power supply Dedicated Portable enclosure urrent: 2 x 20 ma Voltage: 2 x 0 10 V D Temperature: 2 x wire 1 kω RTD Totalizer commands (clear/hold) urrent: 2 x 20 ma D (1 kω at 30 V D) Voltage: 2 x 0 10 V D (5 kω minimum) Status Alarm: x SPDT Relays Mercury wetted relays Frequency: 2 x Hz RS232 Expanded I/Os ( additional ma outputs) with form c relays Expanded I/Os with Mercury wetted relays ± 0.5% % of flow, for velocities greater than 0.3 m/s (1 ft/s) ± m/s (± ft/s), for velocities less than 0.3 m/s (1 ft/s) ± 0.15% of flow, for velocities greater than 0.3 m/s (1 ft/s) ± m/s (± ft/s), for velocities less than 0.3 m/s (1 ft/s) Dedicated wall mount enclosure: IP65 (NEMA X) Portable enclosures: IP0 (NEMA 1) ( F) ( F) ( F) ( F) ( F) see "System info and selection guide" see diagrams V A, Hz, 30 VA or V D Rechargeable battery Indication and operation Data logger memory Display Keypad Language options ertificates and approvals Dedicated enclosures 1 Mbyte of storage 128 x 20 pixel LD with backlight 33 keypad buttons with tactile feedback English, spanish, german, italian, french FM and SA ratings I.S. lass I, II, Div 1 NI lass I, Div 2 S lass II, Div 2 E ATEX ratings INMETRO ratings Portable enclosures E EM Directive 200/108/E LVD Directive 2006/95/EG -TIK Transmitter: Ex II (1) G [Ex ia] II Ex II 3 (1) G Ex n [ia] II T5 Sensors: Ex II 1 G Ex ia II T5 Transmitter: [BR-Ex ia] II BR-Ex nc [ia] II T5 Sensors: BR-Ex ia II T5 UL ULc EM Directive 200/108/E LVD Directive 2006/95/EG /318 Siemens FI

3 Siemens AG 2010 Flow Measurement Standard MLFB for quick delivery on SITRANS FUE1010 (Energy system) Selection and Ordering data Order No. Order code SITRANS FUE1010 Energy lamp-on L) 7 M E Design Dedicated IP65 (NEMA X) 0 K K R 0 2 Portables IP0 (NEMA 1) Battery powered 2 K K R 0 1 Number of channels/ultrasonic paths Dedicated meters Single channel 1 Portable meters Dual channel/dual path Flowmeter functions and I/O configurations Portable Standard I/O - Energy efficiency OP/EER output - 2x -20mA analog input Dedicated Standard I/O - Reflexor apability - Energy efficiency OP/EER output - 2x -20mA analog input Meter power options V A (Dedicated only) A harger Type A for Europe (EE7/7) harger Type K for U.S. (NEMA 5-15P) G No charger J ommunication options RS 232 (standard) 0 RTD temperature sensor pair No RTDs (Note: Temperature input is required for Energy systems) 0 1x Pair Std clamp-on RTD (NEMA X only) 3) 1 2x Pair Std clamp-on RTD (For Dual hannel NEMA X only) 3) 2 1x Pair Std clamp-on RTD (For NEMA 12 portable) 3) 3 2x Pair Std clamp-on RTD (For Dual hannel NEMA 1 portable) 3) 1x Insertion RTD with Thermowell and Lagging 2x Insertion RTD with Thermowell and Lagging Sensor for channel 1 (includes pipe mounting kit and spacer bar for indicated max. OD listed) See Sensor selection charts for specifications. no sensor A A2 universal Trackmount and 75 mm (3") B B3 universal Trackmount and 125 mm (5") 3 universal 300 mm (13") D D3 universal 600 mm (2") E E2 universal 1200 mm (8") 1)) F 1H (high precision) 1200 mm (8") ) M 2H (high precision) 1200 mm (8") ) N D1H (high precision) 1200 mm (8") ) P D2H (high precision) 1200 mm (8") ) Q Doppler to 12" with strap kit (not for IP65 (NEMA7)) S D1H High temperature range 10 / 220 F HP 2) P 1 P L) Subject to export regulations AL: N, EN: 3A991X. F M 1 A M 1 B Siemens FI /319

4 Flow Measurement Siemens AG 2010 Selection and Ordering data Order No. Order code SITRANS FUE1010 Energy lamp-on L) 7 M E Sensor for channel 2 (includes pipe mounting kit and spacer bar for indicated max. OD listed) See Sensor selection charts for specifications. no sensor A A2 universal Trackmount and 75 mm (3") B B3 universal Trackmount and 125 mm (5") 3 universal 300 mm (13") D D3 universal 600 mm (2") E E2 universal 1200 mm (8") 1)) F 1H (high precision) 1200 mm (8") ) M 2H (high precision) 1200 mm (8") ) N D1H (high precision) 1200 mm (8") ) P DH (high precision) 1200 mm (8") ) R Doppler to 12" with strap kit (not for IP65 (NEMA7)) S D1H High temperature range 10 / 220 F HP 2) Q 1 P Approvals UL/Portable 0 FM, SA, E, -TIK/Dedicated 1 1) Supplied spacer bar supports pipes up to 1050 mm (2 inches). For pipes larger than 1050 mm (2 inches) purchase also, spare part 7ME3960-0MS0 (1012BN-) 2) Supplied spacer bar supports pipes up to 750 mm (30 inches). For pipes larger than 750 mm (30 inches) purchase also, spare part 7ME3960-0MS0 (1012BN-) 3) Requires two R** cables per one RTD pair ) 600 mm (2") for portable systems only L) Subject to export regulations AL: N, EN: 3A991X. Standard MLFB product offering represents to 6 weeks delivery time For sensor and RTD cables for quick delivery see tables at end of section /320 Siemens FI

5 Siemens AG 2010 Flow Measurement Selection and Ordering data Order No. Ord. code SITRANS FUE1010 Energy clamp-on Dedicated IP65 (NEMA X) Portables IP0 (NEMA 1) battery powered Number of channels/ultrasonic paths Dedicated meter Dedicated meter Single channel 1 Dual channel / Dual path 2 Portables Dual channel / Dual path Flowmeter functions and I/O configurations Portable Standard I/O - Reflexor capability - Graphic display - 2 x V - 2 x ma - 2 x pulse output - x status logic - Energy efficiency OP/EER output - 2 x ma analog input Dedicated Standard I/O - Reflexor capability - Graphic display - 2 x V - 2 x ma - 2 x pulse output - x relay type - Energy efficiency OP/EER output - 2 x ma analog input L) 7ME3500- L) 7ME Standard I/O with Mercury wetted relays J 1 A Extended output adder plus standard inputs ( additional ma outputs) and form relay Extended output adder plus standard inputs ( additional ma outputs) and Mercury wetted relays Meter power options V A (Dedicated only) A V D (Dedicated only) B harger Type A for Europe (EE7/7) harger Type for Australia (AS3112) D harger Type D for U.K. (BS1363) E harger Type J for Japan (JIS8303) F harger Type K for U.S. (NEMA 5-15P) G harger Type L for Switzerland (SEV1011) H No harger J External hours battery with US plug for Portable External hours battery with European plug for Portable ommunication options RS232 (standard) 0 MODBUS (dedicated only) 1 F J 1 B J 1 K 1 A K 1 B RTD temperature sensor (includes mounting hardware for pipes above 1.5 outer diameter) Selection and Ordering data Order No. Ord. code SITRANS FUE1010 Energy clamp-on Dedicated IP65 (NEMA X) Portables IP0 (NEMA 1) battery powered No RTDs (Note: temperature input is required 0 for energy system) 1 x pair standard clamp-on RTD (NEMA X only) 3) 1 2 x pair standard clamp-on RTD (for dual channel NEMA X only) 3) 2 1 x pair standard clamp-on RTD (NEMA 1 portable) 3) 3 2 x pair standard clamp-on RTD (for dual channel NEMA 1 portable) 3) 1 x Insertion style RTD with thermowell and 9 M 1 A lagging 3) 2 x Insertion style RTD with thermowell and lagging 3) 9 M 1 B Sensor for channel 1 Including pipe mounting tracks for sizes A & B sensors indented for pipe with a OD less than 125 mm (5") and mounting frame/spacer bars for sizes, D & E sensors. Straps provided are for the indicated maximum OD listed below. Strap kits are available to accommodate larger pipes (refer to spare part list). Refer to "Sensor Selection harts" for the sensor suitability of pipe size and wall thickness. No sensor A2 universal B3 universal 3 universal D3 universal E2 universal Trackmount and straps 75 mm (3 ) Trackmount and straps 125 mm (5 ) 300 mm (13 ) 600 mm (2 ) 1200 mm (8 ) 1)) For the following A1H to DH sensors, temperature range is -0 to 65 (-1 F to 150 F), nominal 21 (70 F): A2H (high precision) Trackmount and straps 75 mm (3 ) A3H (high precision) Trackmount and straps 75 mm (3 ) B1H (high precision) Trackmount and straps 125 mm (5 ) L) 7ME3500- L) 7ME ) Supplied spacer bar supports pipes up to 1050 mm (2 inches). For pipes larger than 1050 mm (2 inches) purchase also, spare part 7ME3960-0MS0 (1012BN-). 2) Supplied spacer bar supports pipes up to 750 mm (30 inches). For pipes larger than 750 mm (30 inches) purchase also, spare part 7ME3960-0MS0 (1012BN-). 3) Requires two R** cables per one RTD pair ) 600 mm (2") for portable systems only L) Subject to export regulations AL: N, EN: 3A991X. A B D E F H J K Siemens FI /321

6 Flow Measurement Siemens AG 2010 Selection and Ordering data Order No. Ord. code SITRANS FUE1010 Energy clamp-on Dedicated IP65 (NEMA X) Portables IP0 (NEMA 1) battery powered Sensor for channel 1 (continued) B2H (high precision) Trackmount and straps L 125 mm (5") 1H (high precision) M 1200 mm (8 ) 3) 2H (high precision) N 1200 mm (8 ) 3) D1H (high precision) P 1200 mm (8 ) 2)3) D2H (high precision) Trackmount and straps Q 1200 mm (8 ) 2)3) DH (high precision) Trackmount and straps R 1200 mm (8 ) 2)3) Doppler to 12 with strap kit S High temperature sensor size 2 for up to 230 (6 F) (30 to 200 mm diam. (1.18 to 7.67 inch diam.)) High temperature sensor size 3 for up to 230 (6 F) (150 to 610 mm diam. (5.90 to 2 inch diam.)) High temperature sensor size for up to 230 (6 F) (00 to 1200 mm diam. (15.75 to 7.25 inch diam.)) P 1 A P 1 B P 1 For the following B1H to DH sensors, temperature range is -1 up to 10 (30 F up to 220 F), nominal 65 (150 F): B1H (high temperature range HP) P 1 K B2H (high temperature range HP) P 1 L 1H (high temperature range HP) P 1 M 2H (high temperature range HP) P 1 N D1H (high temperature range HP) 2) P 1 P D2H (high temperature range HP) 2) P 1 Q DH (high temperature range HP) 2) P 1 R Sensor for channel 2 (includes pipe mounting kit for indicated max. outer diameter listed) See Sensor selection charts for specifications. no sensor A2 universal B3 universal 3 universal D3 universal E2 universal Trackmount and straps 75 mm (3 ) Trackmount and straps 125 mm (5 ) 300 mm (13 ) 600 mm (2 ) 1200 mm (8 ) 1)3) L) 7ME3500- L) 7ME A B D E F Selection and Ordering data Order No. Ord. code SITRANS FUE1010 Energy clamp-on Dedicated IP65 (NEMA X) Portables IP0 (NEMA 1) battery powered Sensor for channel 2 (continued) For the following A1H to DH sensors, temperature range is -0 to 65 (-1 F to 150 F), nominal 21 (70 F): A2H (high precision) Trackmount and straps H 75 mm (3 ) A3H (high precision) Trackmount and straps J 75 mm (3 ) B1H (high precision) Trackmount and straps K 125 mm (5 ) B2H (high precision) Trackmount and straps 125 mm (5") L 1H (high precision) M 1200 mm (8 ) 3) 2H (high precision) N 1200 mm (8 ) 3) D1H (high precision) P 1200 mm (8 ) 2)3) D2H (high precision) Q 1200 mm (8 ) 2)3) DH (high precision) R 1200 mm (8 ) 2)3) Doppler to 12 with strap kit S High temperature sensor size 2 for up to 230 (6 F) (30 to 200 mm diam. (1.18 to 7.67 inch diam.)) High temperature sensor size 3 for up to 230 (6 F) (150 to 610 mm diam. (5.90 to 2 inch diam.)) High temperature sensor size for up to 230 (6 F) (00 to 1200 mm diam. (15.75 to 7.25 inch diam.)) L) 7ME3500- L) 7ME Q 1 A Q 1 B Q 1 For the following B1H to DH sensors, temperature range is -1 up to 10 (30 F up to 220 F), nominal 65 (150 F): B1H (high temperature range HP) Q 1 K B2H (high temperature range HP) Q 1 L 1H (high temperature range HP) Q 1 M 2H (high temperature range HP) Q 1 N D1H (high temperature range HP) 2) Q 1 P D2H (high temperature range HP) 2) Q 1 Q DH (high temperature range HP) 2) Q 1 R Approvals FM/SA/E/-TIK Dedicated 1 UL/ULc/E Portable 0 1) Supplied spacer bar supports pipes up to 1050 mm (2 inches). For pipes larger than 1050 mm (2 inches) purchase also, spare part 7ME3960-0MS0 (1012BN-) 2) Supplied spacer bar supports pipes up to 750 mm (30 inches). For pipes larger than 750 mm (30 inches) purchase also, spare part 7ME3960-0MS0 (1012BN-) 3) 600 mm (2") for portable systems only L) Subject to export regulations AL: N, EN: 3A991X. /322 Siemens FI

7 Siemens AG 2010 Flow Measurement Selection and Ordering data Further designs Please add - to Order No. and specify Order code(s). able assembly for sensors (add for # of channels) See Sensor cable selection chart able assembly for RTDs (add for # of RTDs) See RTD cable selection chart able termination kit (for one cable pair) dedicated only Termination for standard, plenum and armored sensor cable Termination for submersible sensor cable Order code K.. R.. T01 T11 MLFB example Application example A dedicated clamp-on energy meter is required for two separate return lines. Both will use clamp-on RTDs for the supply and return lines. A power is available and data access will be via MODBUS communication. Pipe 1 is a DN150 (6 ) schedule 0 carbon steel line Pipe 2 is a DN 300 (12 ) ductile iron line MLFB Order No.: 7ME3500-2DA10-2NE0- K03 + K05 + R03 + R05 + R02 + R03 RTD cable termination kit for standard RTD RTD cable termination kit for submersible RTD Insert RTD cable termination kit Wet flow transfer calibration (priced on request) 6 point up to inch (DN 100) 6 point up to 5 to 8 inch (DN 125 to DN 200) 6 point up to 10 to 12 inch (DN 250 to DN 300) 6 point up to 1 to 16 inch (DN 350 to DN 00) 6 point up to 18 to 20 inch (DN 50 to DN 500) 6 point up to 22 to 2 inch (DN 550 to DN 600) 6 point up to 26 to 30 inch (DN 650 to DN 750) 6 point up to 32 to 36 inch (DN 800 to DN 900) Tag name plate Stainless steel tag with 3.2 mm (0.13 inch) character size (68 characters max.) T21 T31 T1 D10 D11 D12 D13 D1 D15 D16 D17 Y19 Selection and Ordering data Order No. Ord. code FUE1010 meter family 7 M E IP65 (NEMA X) enclosure 0 Dual channel 2 Dedicated Type 1 I/O option V A power option A MODBUS option 1 2 pairs of clamp-on RTDs 2 Sensor code for 6 pipe Sensor code for 12 pipe No approval required 0 30 m (100 ft) sensor cable for channel 1 61 m (200 ft) sensor cable for channel 1 D N E K 0 3 K m (100 ft) cable for RTD 1 R m (200 ft) cable for RTD 2 R m (50 ft) cable for RTD 3 R m (100 ft) cable for RTD R 0 3 Selection and Ordering data Operating Instructions for FUE1010 Order code English NEMA x A5E D) German NEMA x A5E D) English IP0 NEMA 1 A5E A German IP0 NEMA 1 A5E A This device is shipped with a Quick Start Guide and a D containing further SITRANS F literature. All literature is also available for free at: D) Subject to export regulations AL: N, EN: EAR99H Siemens FI /323

8 Flow Measurement Siemens AG 2010 Sensor selection charts Universal sensors for any pipe material Sensor Order code Outer diameter range (mm) Outer diameter range (inches) Size code min max min max A2 B B D D3 E E2 F High precision sensors for steel pipe with outer diameter/wall thickness ratio > 10 Sensor Size code Order code Pipe wall (mm) Pipe wall (inches) min max min max A1H G A2H H A3H J B1H K B2H L H M H N D1H P D2H Q DH R Sensor cable selection chart Sensor cable codes for length and type options able length m (ft) Standard (PV jacket) ( F) Order code Submersible 1) (polyethylene jacket) ( F) Plenum Rated (teflon jacket) ( F) 6 (20) K01 2) K11 K21 K31 Armored 1) 15 (50) K02 K12 2) K22 K32 2) 30 (100) K03 2) K13 2) K23 K33 6 (150) K0 2) K1 K2 K3 61 (200) K05 K15 K25 K35 91 (300) K06 2) K16 K26 K ( F) 1) 2) Submersible and armored sensor cable is not available for portable versions. Standard MLFB for quick delivery RTD cable selection chart RTD cable codes for length and type able length m (ft) Standard (teflon wrapped) ( F) Order code 6 (20) R01 2) R21 15 (50) R02 2) R22 30 (100) R03 2) R23 6 (150) R0 R2 61 (200) R05 R25 91 (300) R06 R26 Insert 1) ( F) 1) 2) Submersible RTD cable is not available for portable versions. Standard MLFB for quick delivery /32 Siemens FI

9 Siemens AG 2010 Flow Measurement SITRANS FUE1010 HVA heck metering kit Overview Design IP0 (NEMA 1) Impact resistant enclosure, constructed of flame retardant ABS with polycarbonate display and polyester keypad Dual channel/dual path The SITRANS FUE1010 dual channel clamp-on check metering kit is an all inclusive HVA chilled water kit developed especially for verifying the accuracy and performance of any brand or type of flowmeter. The meter's portability makes it capable of verifying the performance of meters based on any existing flow measurement principle: electromagnetic, vortex, insertion turbine, or ultrasonic. Perfect for areas where no metering exists. Ideal for balancing building performance. It accurately computes flow over an extremely wide range and measures practically all conductive or non-conductive clean or moderately aerated liquids or liquids with suspended solids. Dual channel models can measure two separate applications at the same time. Benefits Performance check or verification of any type or brand of flowmeter Measures energy rate and total consumption with highest accuracy available Accurately measures at both low flow rates and low differential temperatures Field use is facilitated by meter portability charge for hours of normal operation 1 MByte datalogger capability downloadable to P via included RS232 cable Performs fast, easy and cost-efficient on-site measurement of any convoluted pipe from 25. mm to 9.1 m (1.0" to 360") Delivered as an all inclusive kit with all the equipment needed to conduct performance and verification tests (cables, multiple sensors, flow transmitter etc.) omes in a sturdy rolling case with a telescope handle that holds all the equipment needed to conduct performance and verification tests. Function Integral 33 button keypad and large (128 x 20 pixel) graphic display visible up to 12 m (0 ft) away -wire 1000 Ω platinum RTD's for supply and return temperature measurements are precision matched to within 0.01 (0.02 F) hiller efficiency analysis: accepts an independent analog input representing kw usage for calculation of the following functions which can be selected for data logging or output purposes: - ooling load (kw/ton) - oefficient of performance (OP) - Energy efficiency ratio (EER) Temperature is factory calibrated with built-in field calibrator Built-in energy/btu mode Detection of aeration and cavitation caused by worn or damaged impellers, misaligned shafts, etc. urrent, voltage, frequency and RS232 outputs (see specification section for details) Optional current, voltage and temperature inputs (see specification section for details) eromatic Path automatically sets zero Bi-directional flow operation 1 MByte data logger with both site and data logger storage English, spanish, german, italian and french language options Technical specifications Pipe sizes 25. mm to 9.1 m ( ) Accuracy ± 0.5 %... ± 2.0 % of flow rate Flow range 12 m/s (0 ft/s) bidirectional Media temperature ( F) Enclosure ratings IP0 (NEMA 1) impact resist See page /318 for complete technical specifications erificates and approvals Portable enclosures Unclassified locations lassified locations E UL ULc EM Directive 200/108/E LVD Directive 2006/95/EG Application The SITRANS FUE1010 check meter kit is a highly accurate clamp-on non-intrusive ultrasonic flow display transmitter or revenue grade thermal energy sub-metering and energy efficiency distribution monitoring, with a real time coefficient of performance (OP) for HVA systems. This kit is ideal for applications which include: hilled water sub-metering ondenser water Potable water Ammonia and glycol River and lake water Lake source cooling Siemens FI /325

10 Flow Measurement SITRANS FUE1010 Energy clamp-on heck metering kit Siemens AG 2010 Selection and Ordering data HVA chilled water and energy check metering kit ontent of delivery 1 Dual channel portable submersible flow transmitter 1 pair Universal sensors 3 1 pair Doppler sensors 1 pair High precision sensors 2 1 pair High precision sensors D1 2 pairs RTDs 2 pairs Mounting Ezclamp ( mounting Ezclamp chains) 1 Battery charger 2 pairs 6 m (20 ft) sensor cables 1 RS 232 cable RTD cable 6 m (20 ft) Mountings for RTDs 1 Spacer bar (portable) 2 F connector to BN 1 Flow case 1 Flow meter manual 1 Laminated card set 1 ertificate of intrinsic calibration Order No. QO:FUEHVAKIT /326 Siemens FI