QUICK INSTALLATION GUIDE

Transcription

1 QUICK INSTALLATION GUIDE Internal port in the upper console box Rear View 1 PC or Source (Satellite receiver, Camcorder etc.) Buttom View 1. Connect signal and power code under poweroff PC located in console box in the bottom of product. 1 In case connecting HDMI in-put cable with DVI out-put : You can use when the peripherals with DVI output are connected. 2. Connect power code with product. 3. Turn on the product. The display will operate within 10 seconds. It might happen to not work display if connecting signal cable with PC! turning on. (In case of not display, display will work well if press ALT + CNTL + F4 of keyboard at the same time.) Surely, check connection signal cable with correct before turning on PC. All the time, turn-off or turn-on the console box power of the top of product and PC power inside bottom console box. * Above mentioned is related with PC NDSi161 model only HOLE Wedge Anchor 1/2 (M12)! Product is installed at where the place is clean and product does not sink under water even though heavy raining. It must be installed at where water does not flood at least over the bottom of the product. PN R00

2 46" OUTDOOR KIOSK

3 For the following product : Manufactured at : DECLARATION OF CONFORMITY HYUNDAI IT Digital Signage Provides (factory name, address) 1. Hyundai IT Corp In-ri, Apo-eup Gimcheon, Gyeongsangbuk-do Rep. of Korea 2. Hyundai IT Corp. San Ami-ri, Bubal-eub, Ichon-si, Kyungki-Do, Rep. of Korea We hereby confirm to comply with the requirement set by the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive (89/336/EEC), Low-Voltage Directive(73/23/EEC, 93/68/EEC). For the evaluation regarding the Directives, the following standards were applied: IEC 60065/A1:2005 EN 55022:2006 Class A EN 55024/A2:2003 EN : 2006 EN /A2 :2005 Accredited test laboratory : : TUV SUD Product Service GmbHRidlerstrasse Munchen - Germany KOREA / April 30, 2010 (Place and date of issue) Jong Won, Choi (Name and signature of authorized person)

4 Contents Major features...2 Safety Information...2 Be sure to understand...4 Check the accessories list...5 Proper location for product installation...5 Title and function of each part...6 How to Connect...9 Support timing for HDMI Support timing for PC Adjusting OSD and explanation of its function...12 Diagnosis...26 Specifications...28 * REMOTE CONTROL / RS232C COMMAND SPEC

5 Major features Safety Information This product has been designed to enable users ease of use and display information effectively and conveniently. This product is designed to ensure user's safety. Avoid the following items to prevent serious electric shock and other dangers. protective earthing connection. electric shock. Call service engineer for replacement since it may cause electric shock or fire. remain readily operable.

6 the product. adding a little water. Please contact the local service engineer. English

7 Be sure to understand CAUSE identical frames / images are displayed continuously. If displayed for prolonged periods of time this can become permanent. PREVENTION COUNTERMEASURES Temporary afterimage can be alleviated by displaying white or moving frame about 10 displaying a still frame for a certain time. It can take several minutes or hours to remove afterimage according to the severity. In prevent it by displaying moving image for 2 or 3 minutes in every hour. As the brightness lower the brightness in that case.! Above problem shall not be covered by warranty.

8 Check the accessories list Please check the following components provided with the product after you open the box. English! Remote control & batteries Please check the following components provided with the product after you open the box and contact the dealer if any missing. The contents may vary depending on models and sometimes the contents may be attached on the product. Proper location and recommended installation heavy raining. It must be installed at where water does not flood at least over the bottom of the product. the wall.! badly or knocked.

9 Title and function of each part Control Panel 1 Remote control receiving sensor. 2 3 ~ 0 OSD button. 3 Power button : to turn the power on or off. 4 Input selection button : to select other connected 5 Menu button : to display menu or exit from the menu. 6 Select button. 7 To move down in OSD menu. 8 To move up in OSD menu. 9 To move left and control the volume down in OSD menu. 0 To move right and control the volume up OSD menu. POWER SOURCE MENU SELECT VOL * The locations of OSD board and remote control receiving sensor may vary depending on models.

10 Terminal panel 1 HDMI IN English PC or Source

11 Remote control Turn the power on or off. 2 Move up in OSD menu. 3 Move left in OSD menu. 4 Move right in OSD menu. 5 Move down in OSD menu. 6 Select in OSD menu. 7 Display the menu screen. 8 Close the menu screen. 9 Convert the input signal. How to insert batteries Pull while pressing at rear lid. Insert the batteries into proper polarities

12 How to Connect English PC or Source 1. before restoring power. 1 when connect HDMI to HDMI cable Connect the power code to the product. 3. Turn on the power of the product and peripheral device. Screen shows up within 10 seconds.! Please always turn on or off with the power the console box at the top and bottom of PC in the con sole box.

13 Support timing for HDMI NO Resolution 1 480p 640 x 480p / i 1920 x 1080i 50 / x x * 1600 x * 1920 x * 1080p 1920 x 1080p 60!

14 Support timing for PC NO Resolution x 480 English x / * 1280 x x * 1920 x !

15 Adjusting OSD and explanation of its function Input & Information Input Source PC HDMI Component 2. Press button to select the desired Source. 3. Press button to selection. U Move 8 Enter Information PC Picture Mode Middle Sound Mode Standard Sleep Timer Off Clock 12 : 30 Press button No Signal "No Signal" message is shown in case of no connected signals. Out of Range "Out of Range" Message is shown in case of the excess of an input source range.! The brightness of the display product may go dark in case the temperature inside the product is too high. It's the protection function and restores the brightness to its original state after a while.

16 How to Select the Picture Mode Picture PC Picture PC Picture Mode : Middle Picture Mode : Custom Custom Custom High Colour Tone Colour Tone Middle : : Low PC PC English U Adjust 8 Enter - Menu U Adjust 8 Enter - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press or 3. Press or buttons to select "Picture mode". 4. Press button to select the desired mode. The mode is changed in the following order.

17 How to Set the Desired Picture Picture PC Custom PC Picture Mode : Middle Custom Colour Tone : PC Brightness : Contrast : 80 U Adjust 8 Enter - Menu U Move } Adjust - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press or buttons to select "Picture Mode". 3. Press button to move to "Custom" and press buttons to go to the sub menu. Custom menu will appear. or button to adjust.

18 How to Select a Colour Tone Picture PC Picture Mode : Middle Custom Colour Tone : PC Colour Tone PC Colour Tone : Normal Red : 50 Green : 50 Blue : 50 English U Adjust 8 Enter - Menu U Move 8 Enter - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press or buttons to select "Picture Mode". 3. Press button to move to "Colour Tone" and press buttons to go to the sub menu. Colour Tone menu will appear. 4. Press or buttons to select "Colour Tone" 5. Press enabled. or button to adjust.

19 Picture PC Picture Mode : Custom Colour Tone 4 : 3 : PC U Adjust } Select - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press or buttons to select "Picture Mode". 3. Press 4. Press or buttons and press then the mode changes in the following order. 5. General broadcast picture is adjusted to 16:9.

20 How to set image adjustment in PC mode Picture PC Picture Mode : Middle Custom Picture PC Auto Adjust Phase : 52 English Colour Tone : 16 : : 24 PC : U Adjust 8 Enter - Menu U Move 8 Enter - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press or buttons to select "Picture Mode". 3. Press button to move to "PC" and press buttons to go to the sub menu. PC menu will appear. or button to adjust.

21 How to Select the Audio Sound PC Mode : Custom : Standard Balance : Music Movie : Speech Sound Mode : U Adjust 8 Enter - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press button to move to "Sound Icon". 3. Press or "Mode" is highlighted. 4. Press or. 5. Press button to select the desired mode. The mode changes in the following order. 6.

22 How to adjust the Audio Mode Sound PC Sound PC Mode : Custom 50 : 34 Balance : L50 R : Off 50 Sound Mode : Stereo 50 English U Move 8 Enter - Menu U Move L Adjust - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press button to move to "Sound Icon" and Press or buttons. 3. Press button to move to "Balance" or " ". 4. Presss or button to adjust.

23 Sound PC Mode : : Balance : On : Off Sound Mode : 1. Press Menu button. Menu items appear on the screen. 2. Press button to move to "Sound Icon" and Press or buttons. 3. Press or button. 5. Press or buttons to set to "On/Off". U Adjust 8 Enter - Menu How to Select Sound Mode Sound PC Mode : : Balance : Stereo : Mono L Sound Mode : Mono R U Select 8 Enter - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press button to move to "Sound Icon" and Press or buttons. 3. Press button to move to "Sound Mode" and Press or buttons. 4. Press "Mono R. a Stereo signal.

24 How to Reset Setup PC Reset Time Language : OSD Tone : : 1. Press Menu button. Menu items appear on the screen. 2. Press button to move to "Setup Icon" and Press or buttons. "Reset" is highlighted. 3. Press buttons to select to "Reset". English 8 Select - Menu Time PC Clock : 00 : 00 On Timer : 00 : 00 Off Off Timer : 00 : 00 Off : 20 Source : PC U Move 8 Enter - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press button to move to "Setup Icon" and Press or buttons. 3. Press button to move to "Time" and Press or buttons. 4. Press Press Go to step 5 if you need to set the "On or Off Timer".

25 Time PC Clock : 05 : 00 On Timer : 00 : 00 Off Off Timer : 00 : 00 Off : 20 Source : PC 5. Press button to move to "On or Off Timer" and Press or buttons. 6. Press / on/off and Press / on/off Press or buttons. U Move 8 Enter - Menu 8. Press / Go to step 9 if you need to set the "Source". 9. Press button to move to "Source" and Press or buttons. 10. Press / button to set to Source. How to choose different languages Setup PC Reset English Time Language : Deutschland OSD Tone : Italiano : Español Nederland Suomi Polski Čeština Pyccĸий U Adjust 8 Enter - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press button to move to "Setup Icon" and Press or buttons. 3. Press button to move to "Language" and Press or buttons. 4. Press / button to select to "Language".

26 How to set OSD tone Setup PC Reset Time Language : Off OSD Tone : On : 1. Press Menu button. Menu items appear on the screen. 2. Press button to move to "Setup Icon" and Press or buttons. 3. Press button to move to "OSD Tone" and Press or buttons. 4. Press or buttons to set to "On/Off". English U Adjust 8 Enter - Menu Setup PC Reset Time Language : OSD Tone : Off : On 1. Press Menu button. Menu items appear on the screen. 2. Press button to move to "Setup Icon" and Press or buttons. 3. Press or buttons. 4. Press or buttons to set to "On/Off". U Select 8 Enter - Menu

27 How to Set the Temperature Control "Temperature Control" allows you set up fan operation according to interior temperture of the product. Multi PC Multi PC Temp Control Light Sensor : Auto : 36 C Hysteresis : 5 C Temprature : 29 C U Move 8 Enter - Menu U Move 8 Enter - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press / button to move to "Multi Icon". 3. Press or 4. Press or buttons to select "Temp Control". Temperature Control menu appears. button to set and adjust. Hysteresis : Tolerance value of fan operation temperature. Temperature : Measure current temperature by sensor affixed to PCB'A.

28 How to Set the Light Sensor Light sensor is a feature which the product have the ability to adjust the brightness of the screen automatically according to the external brightness. Multi PC English Temp Control Light Sensor Auto High Middle Low U Move 8 Enter - Menu 1. Press Menu button. Menu items appear on the screen. 2. Press / button to move to "Multi Icon" and Press or buttons. 3. Press / button to move to "Light Sensor. 4. Press or buttons and press then the mode changes in the following order. Auto : It will automatically adjust the screen brightness according to the external brightness of the product. 5.

29 Diagnosis Symptoms Screen displays late after the power is on. How to solve the problem It happens not to show the screen noise when the power is on. Therefore it is not a contact the customer center. The screen is too dark or bright? Adjust the brightness or contrast. The screen doesn't show up indication "Out of range". scrambled. function is not working / the input data were disappeared when reboot the system after setting up the time The screen and sound are Please check the cable connection and the signal generator and contact customer center. values are deleted when the power cord is unplugged. power cord of other peripheral device to the outlet that the product is being connected.

30 Symptoms The screen displays without the sound. How to solve the problem Check the volume up and down with remote control and audio connection cable English No sound from either right speaker or left speaker. Confirm the status of the sound balance on OSD menu and check the connection of speaker cable. Remote control doesn't work. Check if any foreign substances in the sensor and the polarity of battery is inserted. system as it supports Plug and Play. work Check the status of temperature control on OSD menu

31 Specifications LCD Recommended resolution Input Output Power Consumption Control type

32 < REMOTE CONTROL / RS232C COMMAND SPEC > 1. SPEED : 9600 Baud/s, 8 bit, No parity, 1 Stop bit. 2. REMOTE CONTROL WAVE FORM 1) Remote Control System Infrared rey system fosc=455khz fc=fosc/2=37.917khz 2) Signal code 2-1) Transmission - One pulse LEAD CODE CUSTOM CODE LOW CUSTOM CODE HIGH DATA CODE DATA CODE 9ms 4.5ms - Bit description Bit 0 Bit ms 0.56ms 1.125ms 2.25ms - Flame Interval Tf Tf Tf=108ms 455KHz

33 3. REMOTE CONTROL KEY CODE TABLE Custom Code : 7788H DATA LAYOUT KEY POWER DATA 0x80 8O 8D MENU 0x95 8F 8C 9O EXIT SOURCE ENTER UP DOWN LEFT RIGHT 0x96 0xAC 0x8C 0x8D 0x8E 0x8F 0x90 8E AC 4. COMMAND FORMAT * SET ID must select from the OSD menu and can't be select through the COMMAND. * Only one unit can be set as Master unit, selected Master ON from the OSD Menu. (DEFAULT OFF) * For viewing COMMAND from Hyper Terminal windows, One unit must set as MASTER ON HEADER SET ID COMMAND TYPE END did: x- or all- Command <Command example> did:1-pf. To power off set that is SET ID 1 did:all-fr. To factory reset all set did:2-fn. To fan on set that is SET ID 2

34 5. COMMAND TYPE Command pn / pf fn / ff fr Power on / Power off Fan on / Fan off Factory reset sd / sp / sc / sa Source change ( d:hdmi, p:pc, c:component, a:av ) sbu / sbd rou / rod gou / god bou / bod scu / scd rgu / rgd ggu / ggd bgu / bgd blu / bld chxvy nhxvy ehxvy x ( figure ) cr ir ps is Sub-Brightness 1 step up / down Red Offset 1 step up / down Green Offset 1 step up / down Blue Offset 1 step up / down Sub-Contrast 1 step up / down Red Gain 1 step up / down Green Gain 1 step up / down Blue Gain 1 step up / down BACKLIGHT Value 1 step up / down H Set Count is x, V Set Count is y H Set window is x, V Set window is y H Edge ADJ is x, V Edge ADJ is y Display sequence no is x Description Enable Color Control Mode; Under Cr mode, user can set color value without Header command ex) ro120 : Red Offset 120, bg100 : Blue Gain 100 Enable Ir Mode, In IR Mode, user can use keyboard buttons as remote controller Current power status check. If current power is on(off), Hyper Terminal windows display Power On(Power Off) message. Current input source status check. If current input source is VGA, Hyper Terminal windows display VGA Mode message.

35 6. REMOTE CONTROL KEY CODE TABLE Key value Key value q quit ( from Ir mode ) t volume up p power v volume down u up r mute n down c picturemode j left l sleep k right d sound e enter s s.mode m menu y info->display x exit The others quit ( from Ir mode ) i input 7. REMOTE CONTROL KEY CODE TABLE Command did:all-wn=si. did:allfst-hxvy 8. CONNECTION Description Change all units 'Display sequence' to 'SET ID' Set all units to 'H SET Count' = x, 'V SET Count' = y, 'Display sequence' = 'Select to SET ID' Rx Tx G Tx Rx G Pin DIN male 9Pin DIN male