GAT Handheld Coder Pro+ User Manual

Transcription

1 GAT Handheld Coder Pro+ User Manual Rev 1.2 READ INSTRUCTION CAREFULLY BEFORE USE IF YOU HAVE ANY QUESTIONS ABOUT THE USE OF THIS DEVICE, CONTACT YOUR BIMMER RETROFIT REPRESENTATIVE BEFORE USE HANDHELD SHOULD ONLY BE USED WITH APPROPRIATE CABLES INCLUDED WITH THE KIT HANDHELD CAN BE USED ONLY WITH BMW AND VAG* VEHICLES. DO NOT OPERATE HANDHELD UNDER THE RAIN BECAUSE THIS DEVICE IS NOT WATER- RESISTANT AND CAN BE DAMAGED BY WATER DO NOT USE ANY SHARP OBJECTS TO OPERATE A TOUCHSCREEN. USE FINGER OR PLASTIC SIDE OF A PEN TO TOUCH THE ONSCREEN BUTTONS. DO NOT PUSH HARD ON THE TOUCHSCREEN AS IT MAY DAMAGE THE SURFACE HANDHELD CAN ONLY BE CONNECTED TO THE VEHICLE USING SPECIAL OBDII CABLE OR TO THE PC WITH USE OF THE MICRO-USB CABLE. OBDII CABLE IS INCLUDED WITH THE KIT *VAG vehicles support is limited and depends on the current firmware version and vehicle model

2 Contents 1. Device overview Power requirements Device connection and start-up... 6 Vehicle SWT tasks (FSC, Certificates, efsc)... 9 SWID tab... 9 FSC tab Cert tab efsc tab FDL Coding FDL tab ASAP ASAP tab Tools Tools tab DTC DTC tab Settings Settings tab Additional wiring set Online scripts editor Technical Specifications: Contact Us... 24

3 Device overview 1. Power Button 2. OBD II / ENET Port 3. Service Button 4. 5 LCD display with capacitive touchscreen 5. Micro SD card 6. SIM card slot (not used in this version) 7. Secondary micro USB port 8. Primary USB Port RIGHT Side of GAT 1. Secondary Micro USB port (disabled): can be used for device firmware updates and additional device functionality extension. In this version of GAT secondary micro USB functionality is disabled. Functionality to be used in future firmware versions. 2. SIM card Slot (not included): Not used in this version. This version of GAT is equipped with WiFi USB Modem. 3. Micro SD Card slot (not used): can be used as an additional disk drive or for other purposes. In this version of the GAT, this slot can be used in future firmware versions.

4 SIM card Secondary Micro USB Micro SD Card Slot TOP of GAT 4. Power button 5. OBD/ENET port 6. Service button OBD/ENET port Power Button Service Button LEFT side of GAT WiFi dongle plugged into the Primary USB port at the left side of the unit is primary used for all communication with GAT server. It also can be used as a secondary network card for remote work via ENET or ICOM types of connections.

5 Warning! Do not use other than manufacturer - recommended USB WiFi dongles, as this may cause incorrect device functionality. FRONT PANEL of GAT LED lights located on the front panel of GAT are used to monitor current device status Battery charging (red): Red light is ON when battery is charging 2. Power ON (green): Green light is ON whenever the device is turned on 3. LED1 (red) and LED2 (green) are service indicators which may show specific status of device 4. LAN network activity lights show the primary LAN network status (red and green)

6 Portable OBD Port Portable OBD Port with wires allows to connect GAT Coder to power and LAN internet router. Power requirements GAT Coder has internal battery which allows device to work autonomously for minutes. Battery status is indicated in the top info line on LCD display. Whenever battery level is under 50% connect GAT Coder to vehicle s OBD port for charging. Alternatively Portable OBD Port can be used for charging. GAT Coder requires 12V-13.8V and at least 2A for charging of the internal battery. Should simultaneous operation and charging of the GAT coder be required, the power supply with at least 3.5A current and 12V-13.8V will be needed. Whenever GAT Coder is connected to vehicle s OBD port it can be both charged and operated simultaneously. Device connection and start-up To turn ON the GAT Coder press Power button (top right button) shortly. To turn OFF the GAT Coder press and hold Power button for at least 3 seconds. After GAT Coder is turned ON it takes about seconds for it to boot up. As soon as boot process is finished main menu of GAT coder will appear on display.

7 Two different types of connection are supported by GAT Coder Local wired connection (CAN Bus Local) and Remote network connection (ENET or ICOM). Local wired connection via CAN Bus most frequently used connection whenever device is connected via the OBD cable to a vehicle. This connection is always selected by default. Simply connect OBD cable to vehicle and to GAT Coder, make sure that vehicle ignition is ON and press CONNECT button on LCD of GAT Coder. Device will start connection procedure with the vehicle. Progress bar at the bottom right will show the percentage of completion of the process. All information during connection will be shown on the primary information display part at the right side of LCD display.

8 Should ENET or ICOM remote connection be required the device will need to be connected to internet via local LAN (part of the OBD cable) or WiFi dongle. GAT Coder supports connection over internet via port 6801, 6802 and to remotely connected vehicles. At the vehicle side appropriate port should be opened and forwarded to the vehicle s IP. Choose desired connection (ICOM or ENET), type in IP address of the remote internet host with vehicle s port forwarded and type in port (default 6801). Press Connect button once all information is entered. Device will attempt to connect remotely to the vehicle. Once connection is established, vehicle information will appear in the Primary Information Display. If for any reason connection cannot be established the Connect button will become RED and error information will be shown in Primary Information Display. When connection is successfully established, the Connect button will change to Disconnect and will become GREEN. If Disconnect button is pressed, the current connection will be cancelled. Menu Navigation On-screen menu has a tab structure. Each tab has a name associated with it. When a particular tab is selected, the new tab page will be opened on display.

9 From left to right, the tabs are as follows: Connect Connectivity tasks. SWID Reading of the current FSC statuses of head unit FSC FSC code importation Cert Certificate importation efsc Easy FSC (quick FSC) importation FDL FDL Coding of the ECU using scripts ASAP Assistance portal for FSC and scripts downloading and management Tools Additional tools for use with vehicle s ECUs DTC Basic vehicle diagnostic and DTC code removal Settings Configuration tab Vehicle SWT tasks (FSC, Certificates, efsc) SWID tab allows GAT Coder to read out current statuses of all FSC codes loaded in head unit.

10 Pressing the button Read or Re-Read will trigger GAT to pull up current statuses of head unit s SWT and show them on the Information Display. SWID for each FSC as well as its status and status of its Certificate will be shown. In addition statuses of Root, Signatures and Software signatures certificates will be shown on the Information Display together with head unit variant, activation type and head unit bootloader code. Additional technical information from head unit will be shown on Information Display. FSC tab allows read, check and write of FSC codes into head unit. Each available FSC code can be selected with the radio button selector type. Selected FSC code can be read and shown on the Information Display. FSC code can then be saved on local storage inside of GAT by pressing Save button. When different FSC code needs to be loaded instead of currently selected one, the new FSC code will need to be loaded up to Information Display first. This can be done by pressing Load button, selecting appropriate FSC code from local storage and loading it

11 onto to Information Display. Then the Check button should be pressed to verify currently loaded FSC code. Finally Write button should be pressed to write FSC code into head unit. This operation can be repeated for each individual FSC code, if needed. FSC VIN of the head unit can be changed with VIN Write button. VIN number (last 7 digits) must be entered into specific field to the left of the button. Each time FSC code is read or loaded, information about FSC code will appear at the top left corner. FSC Date will show original FSC code creation date (year/month/date); FSC Type will show the creator (Dealer or Factory) and FSC VIN will show the VIN number of the FSC code. Cert tab allows read, check and write of the FSC codes certificates to head unit. Cert tab is very similar to the FSC tab in the way it functions. Each time certificate is read or loaded, the certificate status will appear at the top left corner. Root will show the status of Root certificate (Accepted or Rejected); Sigs will show the status of signature certificate (Accepted or Rejected) and Soft will show the status of software signatures certificates (Accepted or Rejected).

12 Each certificate for FSC can be individually selected, read and written. Usually FSC certificates are imported by the manufacturer and no further changes of these certificates are required. efsc tab allows quick and direct FSC code importation without intermediate verification procedure. This procedure is normally used when all FSC codes of head unit need to be replaced by another set of FSC codes. FSC VIN of head unit will be automatically changed to match the VIN of the newly-loaded FSC set. After pressing Import button, a pop-up screen will appear on the display where you will be able to select an FSC code file from the internal GAT storage for importation. As soon as selection is confirmed, GAT Coder will automatically import and verify the FSC code. Result will be shown on Information Display. This procedure should be repeated for each of FSC code in new set. In case when certificate for a selected FSC code should also be replaced, the Certificate checkbox should be checked before the Import button is pressed. Primary advantage of efsc tab over FSC tab is simplicity of FSC code importation procedure, which does not require any intermediate FSC code verification. Also the VIN number for the FSC code is changed in the head unit automatically. Procedure is very simple and can be described as: select from local storage -> directly load to head unit.

13 FDL Coding FDL tab allows FDL coding for desired ECU with the use of pre-defined coding scripts. Each script contains a list of commands for ECU configuration. List of ECUs available for coding is shown at the left side of the screen. Once the ECU from the list is selected, current software version of the ECU will appear on the Information Display. FDL Coding Procedure

14 1. Desired FDL script should be loaded from the local storage by pressing Load Script button. After pressing Load Script button, a pop-up screen will appear on the display where you will be able to select Desired FDL script. It is important to pay attention to naming of the scripts. Usually script name starts with vehicle series name following by ECU name and then following by actual script name. For example script: F_CIC_VideoInMotion will activate Video in Motion feature in CIC head unit in F series BMW only. You should always load appropriate script for vehicle / head unit which is currently connected. 2. Select desired FDL script from local storage in the pop-up window and press OK. Script will be loaded to the GAT Coder and button Read FDL will become active. By pressing this button the selected script will be parsed and current configuration of ECU will be read and temporary stored by GAT coder. Note that ECU for FDL coding is selected automatically by GAT Coder based on the selected script. After script verification is completed the Apply Script button will become active. By pressing Apply Script button the loaded script will be executed and will change the ECU configuration temporary stored in GAT. Upon completion the button Write FDL will become active.

15 By pressing Write FDL button GAT Coder will start coding process of selected ECU in accordance with ECU s configuration temporary stored in GAT. Once coding is completed confirmation message will be shown. In case of error during the coding the Restore button will become active. Pressing Restore button will restore the ECU back to its original configuration. Warning! It is very important not to interrupt FDL coding process until it is completed. Interruption or disconnection during FDL coding will cause damage to ECU and may require its replacement or special low level re-coding/re-flashing. ASAP ASAP tab allows user to download FDL scripts, which were created in GAT Online system as well as to download FSC codes and manage local FDL scripts and FSCs. Button Get will list all FDL scripts created at GAT online system by the user and available for download. Select desired FDL script from the list at the left and press Download button to copy it to local GAT storage.

16 Local FDL button will list all FDL scripts stored in GAT. To delete FDL script, select FDL script from the list on the left, and press Delete FDL button. Local FSC button lists all FSC codes stored in GAT. Get FSC button downloads FSC code for desired VIN number entered in VIN field. Please note that the quantity of FSC codes you can download is limited by your particular GAT device plan. Tools Tools tab contains additional service commands. Direct commander sends some pre-defined commands directly to ECU. ECU can be selected from drop down menu. Each ECU available in drop down menu is shown in hex address representation and common name. Command can be selected

17 from the drop down menu. Button ECU Direct will send selected command to selected ECU. The result of command execution will appear in information display. Ping ECU button sends standard ping ident request to selected in drop down menu ECU. Result of ping will appear in the information display DTC DTC tab is used for basic diagnostic trouble codes read and erase. By pressing Read DTC button GAT Coder will start reading all DTC trouble codes from each ECU. This process can take a few minutes and depends on the quantity of DTC codes stored in the system. Once DTC codes are read by GAT it is possible to view DTC error codes on the Information Display by using scroll on the right side of the Information Display. Each DTC error code will include its manufacturer s standard number and basic description (if available in the data base). In addition, mileage at which DTC error occurred will also be shown (if available). All DTC error information obtained from the vehicle will be stored on the local storage of GAT for further review, if needed.

18 By pressing Clear DTC button all DTC error codes stored in the vehicle for each ECU will be deleted. DTC light in KOMBI cluster will be turned off. By pressing Reports button it is possible to obtain and view previous DTC error scans from local storage of GAT Coder. Settings Settings tab provides additional settings and GAT Coder functionality configuration. Remote account: enter your Username and Password that you used for registration at the GAT Online system and press Update button. This information required by GAT Coder to access the GAT Online system in order to obtain FDL and FSC downloads and other tasks. Remote auth checkbox should be checked, in order for GAT Coder to perform authorization for FDL coding and FSC tasks between remote server and local system. Whenever internet connection is available during FSC tasks or FDL tasks via WiFi, it is

19 recommended to use Remote auth. In all other cases uncheck Remote auth to keep using local authorization source. WiFi button brings WiFi connection menu on display. Select your desired WiFi SSID, enter security key and press OK. Wait until connection with SSID is established and then press Back arrow to return to Settings tab. Please note that each time GAT Coder is powered OFF and then turned ON again, the WiFi network should be manually re-connected by repeating the steps above. Status button will show current primary IP address used by the GAT Coder. In addition ping packets to localhost will be sent. Bat V button will show current internal battery voltage and also vehicle voltage taken from OBD port of the vehicle. Updater button will connect to manufacturer s server to verify if newer software update is available for GAT Coder. It will open a new GAT Updater window on display. Press on Update button to verify if new updates are available. Warning! GAT Coder should be connected to internet via OBD cable or WiFi for this operation to complete.

20 If newer version is available GAT Updater will automatically download and unpack it. Press Exit button to close GAT Updater and return to GAT Coder application. Please note: Some buttons of Settings tab are locked and will be unlocked in future firmware version updates for GAT Coder. Their respective description will be available in future revisions of this manual. Additional wiring set Additional wiring set allows to connect GAT Coder to power and LAN internet router.

21 Connect red wire to + and black wire to - contact of +12V +13.8V power source with at least 2A current output. This will allow GAT Coder to charge internal battery and operate normally. Plug LAN jack to any DHCP enabled internet router to provide GAT Coder with access to internet if needed. GAT Online System Access Visit and use your username and password to login. Online scripts editor 1. Select Scripts on the left. New webpage will open

22 2. Under ECU Name select desired ECU for which FDL script should be written. 3. Under CAFD File select desired CAFD file. It is preferable to select the latest (highest) version unless otherwise is required. The latest version of CAFD file is normally at the bottom of the list. 4. From the Function Name dropdown menu select desired Setting name which needs to be configured. 5. From Option choice select new value for selected Setting. Alternatively complete byte value can be replaced at once by typing it in Custom HEX field.

23 6. Press Add button to add currently selected Setting and its new value to the script. Repeat Steps 4 6 for each setting that you want to include in the new script. Do not change more than 35 settings at once (i.e. in one script). 7. Select correct vehicle series for this script (E-series or F-series). 8. Once all descried settings and their new values are added to the script, press Export button. Before pressing Export button, make sure that vehicle series is selected correctly (E-series or F-series).

24 9. Enter name of your new script. It is recommended to keep the following naming convention: Series_ECU_Script Name. For example, Video in Motion activation for E- series, will look like: E_CIC_VIM For example, Legal Disclaimer removal for F-series, will look like: F_CIC_LegalDisclaimer Press Save button to save your script on the server. You will be able to download this script from the server using GAT Coder Pro. Technical Specifications: Processor: ARM Cortex A9 1GHz Memory: 512Mb Flash: 4Gb USB: 1 Host high speed, 1 OTG high speed Ethernet: 100Mbit Wi-Fi: n Display: TFT 5 800x480 Graphics controller: Vivante GC880 Temperature: +10 to +55 Celsius External power: 12V 13.8V, 2A minimum Power dissipation: 2.9W Internal battery: Li-Ion 7.2V 850mA Weight: 360g Dimensions: 148x98x35mm Warranty: 1 year from the sale date Contact Us Technical Support Sales Questions For any questions about the use of this device, please contact Bimmer Retrofit Inc. at: support@bimmerretrofit.com or For sales questions and dealership opportunities, please contact Bimmer Retrofit Inc. at info@bimmerretrofit.com or You can also visit us online at Copyrighted 2016 Bimmer Retrofit Inc. All rights reserved.