Network video surveillance camera RVi-IPC42Z12

Transcription

1 Network video surveillance camera RVi-IPC42Z12 User s manual Please read before using and save for later use.

2 Attention This symbol indicates that the device has a high voltage. Contact with parts inside the product is dangerous. This symbol indicates that the product documentation contains important instructions for its use or maintenance. 1. Do not install the unit in humid, dusty, or sooty locations. Failure to do so may result in fire or electric shock. 2. If any unusual smells or smoke come from the unit, stop operation. In this case, immediately disconnect the power source. Continued use in this condition could cause a fire or electric shock. 3. When a fault is detected in the product, contact your nearest service center. Never disassemble the product and do not modify its structure. (RVi Company is not responsible for any problems resulting from changes in product design or as a result of attempted repair products). 4. When cleaning the product, do not expose into the body fluids. This may be a reson of a fire or electric shock. Be careful 1. Do not drop any objects on the product and blows to it. Do not install the product in places with excessive vibration or magnetic interference. 2. Do not install the product in places with high (above 50 C) or low (below -40 C) temperatures or high humidity. This can cause a fire or electric shock. 3. If you want to relocate the already installed product to a new location, then before you do so, turn off the power. 4. During a thunderstorm, it is recommended to disconnect the power supply plug from the AC line. Otherwise, it may cause fire or damage to the product. 5. Install the product so that the lens is not in direct sunlight and not there heat radiation sources. 7. Do not install the product in front of bright light sources (the sun, welding equipment, floodlights), as this may cause damage to the light-sensitive sensor imaging. 2

3 1. Overview of the device 2. Appointment Fig. 1 the type and size of the device IP-camera RVi-IPC42Z12 is designed for broadcast video information to equipment placed on security office and another storage/preview device. The basis of the IP camera is the photo detector matrix, the principle of which is based on the photoelectric conversion sequentially reading the accumulated charges and their subsequent transfer to the digitizing device / image compression with subsequent broadcast video over data networks. The camera has housing with IP66 protection and is designed for outdoor installation. 3

4 3. Specification 4. Delivery set RVi-IPC43-PRO Image sensor 1/2.8 CMOS, Progressive scan Day/Night mode ICR Lens 5.1mm-61.2mm(12x optical zoom), Auto iris Sensitivity 0.01 F1.2 colour / F1.2 BW S/N rate 50 db IR Up to 100 m Resolution, fps 1920x1080, 25 fps Video comretion H.264, MJPEG Audio 1 input/1 output Video BNC output Alarm 1 input/1 output Network 10Base-T/100Base-TX Ethernet port Storage MicroSD up to 64 GB Network protocols HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP, RTSP, RTP, UDP, SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPnP, NTP, Bonjour, SNMPv3, IPFilter, QoS, Multicast, ONVIF Networks tools Build in web server. Network client RVi-PSS for Windows XP и Windows 7, OS Linux, Mac OS. Support mobile OS ios, Android OS, Windows phone OS Power PoE (IEEE802.3af) / DC 12 V (<15 W) Water/dust protection IP66 Working temperature -40 С +60 С Weigh 1,3 kg Dimensions 273х95х95 mm IP camera 1 pcs. User s manual 1 pcs. CD with software 1 pcs. Mount screws 1 set. 4

5 5. Connection All connectors are located on the main patch cord (see. Fig. 2) п п 1 DC 12V 2 RESET 3 I/O Fig. 2 Patch cord Наименование Назначение Тип Функция Connecting a Power Source Reset button to factory settings Alarm input / output 4 LAN Network port 5 AUDIO OUT Audio output port RCA 6 AUDIO IN Audio input port RCA 7 VIDEO OUT Analog video output Connector FW Terminal block with clamp 10Base-T/100Base- TX Ethernet port BNC Hold down the RESET button for 5 seconds to reset the camera to the factory settings. Alarm input for receiving a signal from an external alarm detector. Connected via a standard Ethernet-cable. Supports the transfer of power to the standard PoE. Audio output for passive sound device (eg headphones). Audio input from the microphone. Analogue video output for display on the test monitor or any other device capable to reproduce the analog video signal. 5

6 6. Getting Started Installation and Setup Follow the steps described below (see. Fig. 3): Fig. 3 After mounting the camera on a surface to adjust the angle of the camera (see. Fig. 4), and then tighten the screw on the camera bracket. Fig. 4 6

7 7. Reset to factory settings Factory reset by the button located inside the housing of the IPC. Hold the RESET button about 5 seconds, then the camera will reboot. 8. Quick configuration software Quick configuration software is used to detect the current IP address of the network camera on the network changes its IP address, but also be used to update the camera firmware. CAUTION! Some features may be available only on the condition that the IP-camera and a computer that is running the program on the same subnet. Run (shortcut "ConfigTool.exe"). The software interface is shown in Figure 5. In the list of devices (Device list) you can see the IP-address of the devices, the port number, subnet mask, gateway, the MAC address of the device. Fig. 5 Selecting one of the IP-addresses in the device list, click on it, right-click, and then open the context menu, shown in Figure 6 7

8 Fig. 6 Selecting "Open Device Web", you will find yourself in Web-based interface of the device where you will be prompted to log in to access the network device. * If you want to change the IP-address of the camera without entering the Web-based interface, you must go to the menu list of devices quick configuration utility. In the menu, the list of devices (Fig. 6) to select IP-address of the camera, and then double-click to open the interface "Login" or choose IP-address in the device list and click the "Login" (Fig. 7). Figure 7 displays the window "Login" which displays the IP-address, user name, password, and port number. Each parameter can be changed. Note: The port number must match the TCP port number of the camera installed in the WEB interface. If the camera is updated in the background, to access it using port 3800, other ports are not available. Рис. 7 After login menu will be available for managing network settings of the camera (Fig. 8) * More Web-based interface described in complete instructions for configuring the network camera 8

9 Fig. 8 In this menu you can configure IP address, date / time, update the firmware. 9. Access to the Web interface of the device IPC maintains control through a Web interface and through the software on the PC. WEBinterface allows you to view the camera settings and implement IP-cameras. For network connection IP-cameras, do the following: - make sure that the IP-camera is physically connected to the network. - Set the IP-address, subnet mask and gateway of one network for PC and IPcameras. In IP-cameras standard address , a network mask , gateway To test the connection from the command line, run the command ping (see. Fig. 9) Fig. 9 Open Internet Explorer and enter the IP-address of the camera in the address bar of your browser. For example, if the IP-cameras address , enter in the address bar of Internet Explorer. When you enter the WEB interface you will withdraw the following - Figure 10. Enter your username and password. The default username and password admin. 9

10 Note: For security reasons, urge to change the username and password when you first log in WEB interface. Fig. 10 When you first time connect to the WEB interface, the system message with a proposal to install a component. Click on the OK button, the operating system will automatically install the components. If you are unable to automatically install the file ActiveX, check your browser settings (Tools - Internet Options - Security - Custom Level..). After a successful login you will be taken to the main window WEB interface. 10. Transport and storage IPC in transport containers are transported by any kind of covered vehicles (railcars, closed type holds and compartments of ships, aircraft pressurized heated compartments, etc.) in accordance with applicable regulations. 11. Disposal IPC does not pose no danger to human life and health, as well as to the environment after the end of its life. Disposal of IPC is carried out without taking special measures to protect the environment. 12. Manufacturer's warranty The manufacturer guarantees compliance with IPC technical requirements, subject to terms of transportation, storage, installation and operation. Warranty period - 36 months from the date of sale. In the absence of a mark on the date of sale warranty period is calculated from the date of manufacture 10

11 The warranty is invalid if the cause of the malfunction IPC are: vandalism; fire, flood, natural disasters; accident in the power supply; electrical breakdown chip electronic board due to an error in the polarity of the power. Warranty valid only upon presentation of this manual. The manufacturer is not responsible and does not cover damage caused by the defects caused by the fault of the consumer-compliance with the rules of operation and installation. 11

12 13. Certificate of acceptance and packaging Date of manufacture Date of sale SELLER S Seller STAMP 12