VK2-1080XVFD3V9F(e) User Manual

Transcription

1 VK2-1080XVFD3V9F(e) User Manual

2 Before You Begin Read these instructions before installing or operating this product. Note: This installation should be made by a qualified service person and should conform to local codes. This manual provides installation and operation information. To use this document, you must have the following minimum qualifications: A basic knowledge of CCTV systems and components A basic knowledge of electrical wiring and low-voltage electrical connections Intended use Only use this product for its designated purpose; refer to the product specification and user documentation. Customer Support For assistance in installing, operating, maintaining and troubleshooting this product refer to this document and any other documentation provided. If you still have questions, please contact Norbain Technical Support and Sales: Norbain SD Ltd, 210 Wharfedale Road, IQ Winnersh, Wokingham, Berkshire RG41 5TP, England. UK +44 (0) Note: You should be at the equipment and ready with details before calling Technical Support. Conventions Used in this Manual Boldface or button icons highlight command entries. The following WARNING, CAUTION and Note statements identify potential hazards that can occur if the equipment is not handled properly: * WARNING Improper use of this equipment can cause severe bodily injury or equipment damage. ** CAUTION Improper use of this equipment can cause equipment damage. Note: Notes contain important information about a product or procedure. This apparatus is manufactured to comply with the radio interference. A Declaration of Conformity in accordance with the following EU standards has been made. The manufacturer declares that the product supplied with this document is compliant the provisions of the EMC Directive 2004/108/EC, the CE Marking Directive 93/68 EEC and all associated amendments. All lead-free products offered by the company comply with the requirements of the European law on the Restriction of Hazardous Substances (RoHS) directive: 2011/65/EU, which means our manufacture processes and products are strictly lead-free and without the hazardous substances cited in the directive. The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do not dispose of these products as unsorted municipal waste. * This symbol indicates electrical warnings and cautions. * This symbol indicates general warnings and cautions. NORBAIN SD LTD reserves the right to make changes to the product and specification of the product from time to time without prior notice. WARNINGS AND CAUTIONS: To reduce the risk of fire or electric shock, do not insert any metallic objects through the ventilation grills or other openings on the equipment. 2

3 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICABLE PARTS INSIDE. IMPORTANT SAFEGUARDS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings, Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug, A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety, If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING IN- STRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO. 15. Use satisfy clause 2.5 of IEC /UL or Certified/Listed Class 2 power source only. 16. ITE is to be connected only to PoE networks without routing to the outside plant. CE COMPLIANCE STATEMENT WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 3

4 Contents 1 Introduction Components Key Features Installation Overview Connection Network Connection & IP assignment Operation Access from a browser Access from the internet Setting the admin password over a secure connection Live View Page Playback Network Camera Setup Basic Configuration Live View Video & Image Audio Event System Help Resetting to the factory default settings A Appendix 81 A.1 Troubleshooting A.2 Alarm Connection A.3 Preventive Maintenance A.4 Product Specification A.5 System Requirement for Web Browser A.6 General Performance Considerations

5 1 Introduction The network camera supports the network service for a sensor image with progressive scan, which can be monitored on a real-time screen regardless of distances and locations. By using its dedicated program, many users are able to have an access to the network camera at once or a single user can monitor various network cameras at the same time. It also enables users to play, store and retrieve a monitoring image by using a PC. All the settings and real-time monitoring screens are also provided through an access to the web. The network camera is fully featured for security surveillance and remote monitoring needs. It is based on the DSP compression chip, and makes it available on the network as real-time, full frame rate Motion JPEG and H.264 video streams. The alarm input and alarm output can be used to connect various third party devices, such as, door sensors and alarm bells. 1.1 Components This system comes with the following components; Dome Camera 1 Installation Guide/CD 1 Template Sheet 1 Accessory Kit 1 Check your package to make sure that you received the complete system, including all components listed above. 5

6 1.2 Key Features Brilliant video quality The network camera offers the highly efficient H.264 video compression, which drastically reduces bandwidth and storage requirements without compromising image quality. Motion JPEG is also supported for increased flexibility. Wide Dynamic Range The network camera provides true WDR (Wide Dynamic Range) that improves video exposure quality in scenes with high contrast between bright and dark areas in the video, for example a shady area and a sunny area in the same scene. Dual or Triple Streams The network camera can deliver dual or triple video streams simultaneously at full frame rate in all resolutions up to Full-HD (1920 x 1080p) using Motion H.264 and JPEG. This means that several video streams can be configured with different compression formats, resolutions and frame rates for different needs. Image setting adjustment The network camera also enables users to adjust image settings such as contrast, brightness and saturation to improve images before encoding takes place. Intelligent video capabilities The network camera includes intelligent capabilities such as enhanced video motion detection. The network cameras external inputs and outputs can be connected to devices such as sensors and relays, enabling the system to react to alarms and activate lights or open/close doors. Improved Security The network camera logs all user access, and lists currently connected users. Also, its full frame rate video can be provided over HTTPS. PoE (Power over Ethernet) This network camera can be powered through PoE (IEEE802.3af), which simplifies installation since only one cable is needed for carrying power, as well as video controls. ONVIF Certificate This is a global interface standard that makes it easier for end users, integrators, consultants, and manufacturers to take advantage of the possibilities offered by network video technology. ONVIF enables interoperability between different vendor products, increased flexibility, reduced cost, and future-proof systems. Micro-SD Recording support The Network Camera also supports a micro-sd memory slot for local recording with removable storage. Audio support The Network Camera also supports two-way audio. 6

7 2 Installation For the operation of the Network Camera, it is necessary to connect a network cable for data transmission, power connection from supplied power adapter. Depending on operation methods, it is possible to connect an alarm cable additionally. For its fixation on different locations, please consult with an installer. 2.1 Overview Extension Cable NO Name Description 1 Micro SD Slot Micro SD slot for local recording 2 Status LED Amber : On System Booting Green : Normal Operation NO Wire Color Description 1 Black Ethernet, RJ-45 port compatible with 10/100Mbps PoE Modular Jack 2 Red: DC12V White: GND Main Power, 2pin terminal, DC12V 450mA(4.4W) 3 Yellow: Alarm In Black: GND Alarm input and output, 3pin terminal Violet: Alarm Out 4 Grey: Audio In Black: GND Audio line input, 2pin terminal 5 White/Black: Audio Out Black: GND Audio line output, 2pin terminal 7

8 Installing & Adjusting Camera Module To mount the board camera on the camera mount bracket, place the four board camera supports on the four slot holes near the front and the rear of the camera mount bracket. Note: Arrow mark indicates the top of the camera image. Use the following drawings to install the camera module to the housing. 8

9 Base Installation Make mounting holes and cable hole in the place (ceiling) to which this dome. Camera is installed using the Template sheet. To remove dome cover, turn the dome cover counterclockwise until locators reach end of travel and pull off. Push the liner in the direction of the arrow (three OPEN marks) and pull it out. Fasten Mounting screws(2x) and align the dome camera with it like above picture. Turn the dome camera to left direction about 16 degree. The assembly of the dome window cover and liner is in reverse order of disassembly Finally, lock dome window cover with locking screw(m2x4) from the accessory kit. 9

10 Using the Quick install Adaptor (option) Use the optional Quick install Adaptor on wall or ceiling application 1. Install the Adaptor into the mounting surface and use the screws to adjust the position of the two locking arms on the Quick Install Adaptor 2. Push the cables through the opening and 1/2 hole grommet 3. Make sure the grommet is property installed on the adaptor to prevent dust ingress 10

11 2.2 Connection Micro SD memory slot on the Board Card Slot for Micro SD memory: Socket J15 Connecting to the RJ-45 Connect a standard RJ-45 cable to the network port of the network camera. Generally a cross-over cable is used for directly connection to PC, while a direct cable is used for connection to a hub. You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera. Connecting Alarms AI(Alarm In): You can use external devices to signal the network camera to react on events. Mechanical or electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors. G(Ground): Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector. AO(Alarm Out): The network camera can activate external devices such as buzzers or lights. Connect the device to the AO (Alarm Out) and G (Ground) connectors. Connecting the Power Connect the power of 12 VDC 450mA for the network camera. Connect the positive (+) pole to the + position and the negative (-) pole to the - position for the DC power. Be careful not to reverse the polarity when connecting the power cable. A router featuring PoE (Power over Ethernet) can also be used to supply power to the camera. For the power specifications, refer to the Appendix, Product Specification. If PoE and 12 VDC are both applied, the camera will be supplied with power from PoE. 11

12 2.2.1 Network Connection & IP assignment The camera supports the operation through the network. When a camera is first connected to the network, it is necessary to allocate an IP address to the device with the SmartManager utility on the CD. (Default IP ) 1) Connect the network camera/device to the network and power up. 2) Start SmartManager utility (Start > All programs > SmartManager > SmartManager). The main window will display, and after a short while any network devices connected to the network will be displayed in the list. 3) Select the camera on the list and click right button of the mouse. You can see the pop-up menu as below. 4) Select Assign IP Address. The Assign IP window will display. Enter the required IP address. NOTE: For more information, refer to the SmartManager Users Manual. 12

13 3 Operation The network camera can be used with Windows operating system and browsers. The recommended browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome with Windows. NOTE: To view streaming video in Microsoft Internet Explorer, set your browser to allow ActiveX controls. 3.1 Access from a browser 1. Start a browser (Internet Explorer). 2. Enter the IP address or host name of the network camera in the Location/Address field of your browser. 3. You can see a starting page. Click Live View, Playback, or Setup to enter web page. 4. The network cameras Live View page appears in your browser. 13

14 3.2 Access from the internet Once connected, the network camera is accessible on your local network (LAN). To access the network camera from the Internet you must configure your broadband router to allow incoming data traffic to the network camera. To do this, enable the NAT traversal feature, which will attempt to automatically configure the router to allow access to the network camera. This is enabled from Setup > System > Network > NAT. For more information, please see System > Network > NAT of User s Manual. 3.3 Setting the admin password over a secure connection To gain access to the product, the password for the default administrator user must be set. This is done in the Admin Password dialog, which is displayed when the network camera is accessed for the setup at the first time. Enter your admin name and password, set by the administrator. NOTE: The default administrator user name and password is admin. If the password is lost, the network camera must be reset to the factory default settings. Please see Resetting to the factory default settings. To prevent network eavesdropping when setting the admin password, this can be done via an encrypted HTTPS connection, which requires an HTTPS certificate (see NOTE below). To set the password via a standard HTTP connection, enter it directly in the first dialog shown below. To set the password via an encrypted HTTPS connection, please see System > Security > HTTPS of User s Manual. NOTE: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between web browsers and servers. The HTTPS certificate controls the encrypted exchange of information. 14

15 3.4 Live View Page The Live View page comes in several screen modes: 1920x1080, 1280x1024, 1280x720(960), 1024x768, 704x480(576), 640x480(360) and 320x240. Users are allowed to select the most suitable one out of those modes. Adjust the mode in accordance with your PC specifications and monitoring purposes. 1) General controls Live View Page Playback Page Setup Page Help Page 2) Control toolbar The video drop-down list allows you to select a customized or preprogrammed video stream on the Live View page. Stream profiles are configured under Setup > Basic Configuration > Video & Image. For more information, please see Basic Configuration > Video & Image of Users Manual. The resolution drop-down list allows you to select the most suitable one out of video resolutions to be displayed on Live View page. The protocol drop-down list allows you to select which combination of protocols and methods to use depending on your viewing requirements, and on the properties of your network. The live viewer toolbar is available in the web browser page only. It displays the following buttons: The Stop button stops the video stream being played. Pressing the key again toggles the start and stop. The Start button connects to the network camera or starts playing a video stream. The Pause button pauses the video stream being played. The Snapshot button takes a snapshot of the current image. The location where the image is saved can be specified. The Digital Zoom button activates a zoom-in or zoom-out function for video image on the live screen. 15

16 The Full Screen button causes the video image to fill the entire screen area. No other windows will be visible. Press the Esc button on the computer keyboard to cancel full screen view. The Manual Trigger button activates a pop-up window to manually start or stop the event. The Lens Control button allows user to control Zoom and Focus manually. (This Icon appears for motorized lens model only.) Zoom: Click << or < button to zoom out and click >> or > button to zoom in. The focus is moved slightly after adjusting zoom; adjust the focus again, as necessary. Focus: Click << or < button for far focus and click >> or > button to near focus. The Smart Focus button activates smart focus function which set the focus to the optimum position. (This Icon appears for motorized lens model only.) The VCA button shows/hides VCA rule setting and detected objects. The Face Detection button shows/hides detected faces. The Speaker button activates/deactivates external speaker. The Mic button activates/deactivates microphone input. Use this scale to control the volume of the speakers and microphones. NOTE: VCA and Face Detection works exclusively to each other. 3) Video Streams The network camera provides several images and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the network camera provides access to H.264 and Motion JPEG video streams, and to the list of available video streams. Other applications and clients can also access these video streams/images directly, without going via the Live View page. 16

17 3.5 Playback The Playback window contains a list of recordings made to the memory card. It shows each recording s start time, length, the event type used to start the recording, calendar and time slice bar indicates if the recording is existed or not. The description of playback window follows. (1) Video Screen You can see the video screen when playing the video clip in the Micro SD memory. (2) Playback Buttons To view a recording data in the SD local storage, select it from the list and click the Playback buttons. Go to the first: go to the beginning of the video clip. Fast backward play: fast play backward of the video clip. Backward play: play backward of the video clip. Step backward play: go back one frame of the video clip. Pause: pause playback of the video clip. Step forward play: go forward one frame of the video clip. Forward Play: play forward the video clip. Fast forward play: play fast forward of the video clip. Go to the last: go to the end of the video clip. Clip copy: copy the video clip. Zoom In: zoom in the video clip. Full Screen: display full screen of the video. 17

18 (3) Time Chart Display an hour-based search screen for the chosen date. If there is recording data, a blue section will be displayed on a 24-hour basis. If you select a particular hour in the chart, a yellow square on the hour will be displayed. (4) Speaker Control Bar Use this scale to control the volume of the speakers. (5) Search Calendar Search results from the SD local storage in the network camera connected are displayed monthly. If there is a recorded data for a particular date, a blue square on the date will be displayed. If you select a particular date in the calendar, a yellow square on the date will be displayed. (6) Play Time Displays time of the video playing. (7) Event Search Window Select a search option in the drop-down list and click GO button. You can also enter the time period for searching. If you click Start Date or End Date zone, displays Search Calendar. (8) Event List Window Event List displays the event(s) that were recorded in the SD local storage. Select a list and click the play button. The video clip will be played. 18

19 3.6 Network Camera Setup This section describes how to configure the network camera. Administrator has unrestricted access to all the Setup tools, whereas Operators have access to the settings of Basic Configuration, which are Live View, Video & Image, Audio, Event, Dome Configuration, and System. You can configure the network camera by clicking Setup either in the first connection page or the top second-right button of the Live View page. Accessing the network camera from a computer for the first time opens the Admin Password dialog box. Enter your administrator or operator id and password to get into setup page. NOTE: If the password is lost, the network camera must be reset to the factory default settings. Please see Resetting to the Factory Default Setting Basic Configuration You can see the device information in this information page. 19

20 1) Users User access control is enabled by default. The administrator can set up other users, by giving user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page, as described below: The user list displays the authorized users and user groups (levels): User Group Guest Operator Administrator Authority Provides the lowest level of access, which only allows access to the Live View page. An operator can view the Live View page, create and modify events, and adjust certain other settings. Operators have no access to System Options. An administrator has unrestricted access to the Setup tools and can determine the registration of all other users. Enable anonymous viewer login: Check the box to use the webcasting features. Refer to Video & Image 3) Webcasting for more details. Please refer to System 2) Security Users for more details about User setup. 20

21 2) Network The network camera supports both IP version 4 and IP version 6. Both versions may be enabled simultaneously, and at least one version must always be enabled. When using IPv4, the IP address for the network camera can be set automatically via DHCP, or a static IP address can be set manually. If IPv6 is enabled, the network camera receives an IP address according to the configuration in the network router. There is also an option of using the Internet Dynamic DNS Service. For more information on setting the network, please see System > Network > Basic. Obtain IP address via DHCP: Dynamic Host Configuration Protocol (DHCP) is a protocol that lets network administrators centrally manage and automate the assignment of IP addresses on a network. DHCP is enabled by default. Although a DHCP server is mostly used to set an IP address dynamically, it is also possible to use it to set a static, known IP address for a particular MAC address. Use the following IP address: To use a static IP address for the network camera, check the radio button and then make the following settings: NOTES: IP address: Specify a unique IP address for your network camera. Subnet mask: Specify the mask for the subnet the network camera is located on. Default router: Specify the IP address of the default router (gateway) used for connecting devices attached to different networks and network segments. 1. DHCP should only be enabled if using dynamic IP address notification, or if your DHCP server can update a DNS server, which then allows you to access the network camera by name (host name). If DHCP is enabled and you cannot access the unit, you may have to reset it to the factory default settings and then perform the installation again. 2. The ARP/Ping service is automatically disabled two minutes after the unit is started, or as soon as an IP address is set. 3. Pinging the unit is still possible when this service is disabled. Please refer to System > Network > Basic for more details about Network setup. 21

22 3) Video & Image User can setup and change setting of individual video stream in this page. Please refer to Video & Image > Basic for more details about Video & Image setup. 4) Audio The network camera can transmit audio to other clients using an external microphone and can play audio received from other clients by attaching a speaker. User can setup and change setting of Audio in this page. Please refer to Audio for more details about Audio setup. 22

23 5) Date & Time User can set time directly or assign time server to get the current time, as well as determine Date & Time format in this page. Please refer to System > Date & Time for more details about Date & Time setup Live View Video Input Mode: Video Mode: Choose Video Mode you wish to use from the drop-down list: NTSC or PAL NOTE: This function may not be applicable, depending on the model. 23

24 3.6.3 Video & Image 1) Basic Sensor Setting: Capture mode: User can select sensor capture mode between 30 fps and 60 fps in full-hd resolution. If 60fps is selected, Stream 3 is disabled and hidden from the window. In other words, the camera provides triple stream at 30 fps and dual stream at 60 fps. Stream 1 Setting: Codec: The codec supported in Stream 1 is H.264. There are 3 pre-programmed stream profiles available for quick set-up. Choose the form of video encoding you wish to use from the drop-down list: H.264 HP (High Profile): Primary profile for broadcast and disc storage applications, particularly for high-definition television applications (for example, this is the profile adopted by the Blu-ray Disc storage format and the DVB HDTV broadcast service). H.264 MP (Main Profile): Primary profile for low-cost applications that require additional error robustness, this profile is used rarely in videoconferencing and mobile applications; it does add additional error resilience tools to the Constrained Baseline Profile. The importance of this profile is fading after the Constrained Baseline Profile has been defined. H.264 BP (Baseline Profile): Originally intended as the mainstream consumer profile for broadcast and storage applications, the importance of this profile faded when the High Profile was developed for those applications. 24

25 Resolution: This enables users to determine a basic screen size when having an access through the Web Browser or PC program. The screen size control comes in seven modes like 1920x1080, 1280x1024, 1280x960, 1280x720, 1024x768, 704x576, 704x480, 640x480, 640x360 and 320x240. Users can change the selected screen size anytime while monitoring the screen on a real-time basis. Bitrate control: The bit rate can be set as Variable Bit Rate (VBR) or Constrained Variable Bit Rate (CVBR). VBR adjusts the bit rate according to the image complexity, using up bandwidth for increased activity in the image, and less for lower activity in the monitored area. Limiting the maximum bit rate helps control the bandwidth used by the H.264 video stream. Leaving the Maximum bit rate as unlimited maintains consistently good image quality but increases bandwidth usage when there is more activity in the image. Limiting the bit rate to a defined value prevents excessive bandwidth usage, but images are degraded when the limit is exceeded. VBR: unlimited maximum bitrate. CVBR: VBR with maximum bitrate which is set in Bitrate. Bitrate: Maximum bitrate for CVBR in the range of 100kbps 8Mbps. This is disabled if Bitrate control is set to VBR. Frame rate: Upon the real-time play, users should select a frame refresh rate per second. If the rate is high, the image will become smooth. On the other hand, if the rate is low, the image will not be natural but it can reduce a network load. GOP size: Select the GOP (Group of Picture) size. If users want to have a high quality of fast image one by one, please decrease the value. For the purpose of general monitoring, please do not change a basic value. Such act may cause a problem to the system performance. For the details of GOP setting, please contact the service center. Stream 2 Setting: Sometimes the image size is large due to low light or complex scenery. Adjusting the frame rate and quality helps to control the bandwidth and storage used by the Motion JPEG video stream in these situations. Limiting the frame rate and quality optimizes bandwidth and storage usage, but may give poor image quality. To prevent increased bandwidth and storage usage, the Resolution, Frame rate, and Frame Quality should be set to an optimal value. MJPEG Resolution: Same as the stream 1 settings. MJPEG Frame rate: Same as the stream 1 settings. MJPEG Quality: Select the picture quality. If users want to have a high quality of fast image one by one, please decrease the value. For the purpose of general monitoring, please do not change a basic value. Such act may cause a problem to the system performance. Stream 3 Setting: Same as the Stream 1 Setting. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 25

26 2) Privacy Masking The privacy masking function allows you to mask parts of the video image to be transmitted. You can set up to eight privacy masks and the color of privacy masks is black. The privacy masks are configured by Mask windows. Each window can be selected by clicking with the mouse. It is also possible to resize or delete, or move the window, by selecting the appropriate window at the mouse menu on the video screen. To create a mask window, follow steps: 1. Click the right button of mouse to see the mouse menu. 2. Select New Privacy Mask in the mouse menu. 3. Click and drag mouse to designate a mask window area. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 26

27 3) Webcasting The live video of the camera can be streamed to a website. User can copy and paste the HTML code generated on the screen to the website page code, where user wants to display live video. NOTE: To use webcasting service, the Enable Anonymous viewer login option must be checked. 27

28 4) Camera Setup In this page, user can setup Exposure Control, White Balance Control, Image Appearance, and Day & Night control. Video Preview: User can check the setting via video preview pop-up window 28

29 Exposure Control 1. Mode: Determines exposure mode among automatic and flicker-free modes. 2. Value: Sets exposure value between 1 and 10 using slidebar or manual type in. 3. Max. gain: Sets maximum gain threshold. 4. Shutter: Determines shutter mode between automatic and fixed. For automatic 6 sets the maximum shutter speed, and for fixed 5 sets the shutter speed for the camera. 5. In case of fixed shutter speed, this pull-down shows selectable shutter speeds depend on the exposure selection in Max. shutter: Select maximum shutter speed if Shutter is in automatic mode. The pull-down shows selectable maximum shutter speeds depend on the exposure selection in Enable automatic IRIS adjustment: Activates auto-iris function. 8. Enable backlight compensation: Activates BLC function. 9. Enable wide dynamic range: Activates WDR which cannot be used with Defog function. If WDR is activated, shutter mode in 4 becomes automatic only. 10. Strength: Determines WDR strength. White Balance Control Mode: Select one of four white balance mode which fits camera installation environment. 29

30 Image Appearance This provides access to the advanced image settings for the network camera. Brightness: The image brightness can be adjusted in the range 1-10, where a higher value produces a brighter image. Contrast: Adjust the image s contrast by raising or lowering the value in this field. Saturation: Set an appropriate value in the range Lower values mean less color saturation. Hue: Set an appropriate value in the range The value distinguishes color, such as red, yellow, green, or violet. Sharpness: Set the amount of sharpening applied to the image. A sharper image might increase image noise especially in low light conditions. A lower setting reduces image noise, but the image would be less sharp. Enable flip horizontally: Check this box to flip the image. Enable mirror image: Check this box to mirror the image. Enable noise reduction: Check this box to activate the noise reduction. Once enabled, you can select noise reduction level. Enable defog: Check this box to activate the defog function. Once enabled, you can select defog strength. Enable digital image stabilization: Check this box to activate the DIS(Digital Image Stabilization) function. Once enabled, you can select image stabilization level. Enable aisle: Check this box to activate the image rotation function. This function is rotates 90 o clockwise or counterclockwise, which is useful in monitoring a hallway or an aisle in a store. Once enabled, you can select 90 o (rotate clockwise) or 270 o (rotate counterclockwise). NOTE: Defog function cannot be used in conjunction with WDR. 30

31 Day & Night Control User can setup Day & Night operation mode among Automatic, Day, and Night. Mode: Automatic: Normally displays color image, and switches automatically to black & white image after the ambient light level reaches a pre-defined threshold. Day: Always displays color image. Night: Always displays black & white image. Threshold: Adjusts the level of light which the camera automatically switches between color and black & white image. Smart Focus sync with Dat & Night: Focus control automatically adjusts upon Day/Night change. (This menu appears for motorized lens model only.) When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 31

32 5) OSD This camera provides two OSD s (on screen display) on each stream, title and date & time. User can drag green OSD Title and Date & Time to the desired position and check at preview window. Video Preview: User can check the position of OSD on actual video via preview popup window. OSD Setting: User can determine show or hide OSD for each stream. Also user can set the transparency level of OSD by slide bar or type in number. OSD title: User can show or hide OSD title, and can change OSD title by type in. The default is the model name of the camera. Date & Time: User can show or hide date & time on OSD. NOTE: The change in this page immediately affects video stream. 32

33 3.6.4 Audio The network camera can transmit audio to other clients using an external microphone and can play audio received from other clients by attaching a speaker. The Setup page has an additional menu item called Audio, which allows different audio configurations, such as full duplex and simplex. Audio Setting: Enable audio: Check the box to enable audio in the video stream. Compression type: Select the desired audio Compression format between G.711 µ-law or G.711 a-law. Sample rate: Select the required Sample rate (number of times per second the sound is sampled). The higher the sample rate, the better the audio quality and the greater the bandwidth required. Sound bit rate: Depending on the selected encoding, set the desired audio quality (bit rate). The settings affect the available bandwidth and the required audio quality. Audio Input: Audio from an external line source can be connected to the STEREO Jack I/O of the network camera. Input: User can select amplifier between Internal Amp or External Amp. Input volume: If there are problems with the sound input being too low or high, it is possible to adjust the input gain for the microphone attached to the network camera. Audio Output: Enable full duplex: Check the box to enable Full Duplex mode. This means that you can transmit and receive audio (talk and listen) at the same time, without having to use any of the controls. This is just like having a telephone conversation. This mode requires that the client PC has a sound card with support for full-duplex audio. Uncheck the box enable Simplex mode. The simplex mode only transmits audio from the network camera to any web client. It does not receive audio from other web clients. 33

34 Output volume: If the sound from the speaker is too low or high it is possible to adjust the output gain for the active speaker attached to the network camera. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 34

35 3.6.5 Event 1) Event In On Boot This is used to trigger an event every time the network camera is started. Select Enable on boot to activate the On Boot event. Enter the Dwell time the event lasts from the point of detection, seconds. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 35

36 Alarm In This camera provides 1 Alarm In port and user can set the port. The Port can be given as Normally Open or Normally Close state, and its Normal state can be configured. In order to use the alarm port, check the Enable alarm port 1 first. Type: Choose the type of alarm to use from the drop-down list, NO (Normally Open) or NC (Normally Closed). Dwell Time: Set the dwell time an event lasts from the point of detection of an alarm input. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 36

37 Manual Trigger This option makes use of the manual trigger button provided on the Live View page, which is used to start or stop the event type manually. Alternatively, the event can be triggered via the product s API (Application Programming Interface). Select Enable manual trigger to activate the manual trigger (for up to 4 manual triggers). Set the dwell time the trigger lasts. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 37

38 Motion This option makes use of the motion detection function with 16 programmable areas, 8 Include and Exclude zones each. Click right mouse button on thte preview window shows selection pop-up of New Motion, New Mask, Select, Delete, and Freeze. Select New Motion and click&drag generates an Include box of green color. Select New Mask and click&drag generates an Exclude box of orange color. Drag corner or line resizes and drag inside moves the box. Select Enable video motion detection to activate motion detection. Day & Night selection Day: Sensitivity and threshold values are not changed regardless of lighting condition. item Day & Night: User can set different sensitivity and threshold values for Day and Night condition. Sensitivity: User can change sensitivity of this function, where large value sets more sensitive detection. Zone List ID: Order of generation, Include 1 8, Exclude Name: User definable zone name. Type: shows zone type and cannot be changed. Threshold: Determines how laarge the motion in the zone can trigger event in percentage. 38

39 Dwell time: Determines how long the triggered event holds from the last triggering. User can select any box by clicking name on the preview window or click on the list. User can delete selected zone via right mouse click selection for a selected box, or click any one of X button in the zone list. NOTE: Video Motion detection function cannot be used in conjunction with Video Content Analysis function. If you choose Enable video motion detection, video content analysis function is automatically turned off. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 39

40 Network Loss This is used to trigger an event every time the network connection is failed. Select Enable network loss to activate the Network Loss event. Select a dwell time for how long the event will last from the point of detection. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 40

41 Tampering This is used to trigger an event when camera tampering occurs, for example, obstruct the camera with foreign material or move camera direction using external force. Select Enable tampering to activate the Tampering event. Dwell time: Determine how long the event will last from the point of detection. Event time: Time duration from tampering detection to tampering event trigger. Threshold: Determines sensitivity level to judge tampering. The samller the threshold value, the more frequent tampering event trigger. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 41

42 VCA The network cameras provide VCA(Video Content Analysis) functions of Line Detector and Field Detector. Video Content Analysis Setting Check Enable video content analysis box to use a VCA function. Object: Determines detection sensitivity. Sensitivity: As the value becomes bigger, the detection sensitivity increases. Min width size: Minimum horizontal pixel size for detections in a 1920x1080 format. Min height size: fminimum vertical pixel size for detections in a 1920x1080 format. Max width size: Maximum horizontal pixel size for detections in a 1920x1080 format. Max height size: Maximum vertical pixel size for detections in a 1920x1080 format. 42

43 Detection Rule: User can assign up to 3 different rules for each preset position. Line Detector Once selected, a red line appears on the video preview window. Drag and drop the line at the desired position. User can change the length and the slope by dragging each end of the line. Rule Name: User can type in the rule name. Direction: This detector can detect line crossing events and also count up number of the event; the direction of the event appears as a solid triangle shape at the center of the line. Base: The reference point of the object detection. Counter: User can choose between Counter and Detector. Field Detector Once selected, a blue line appears on the video preview window. Drag and drop the box at the desired position. User can change the shape of the box by dragging each corner to any shape of a quadrilateral. Rule Name: User can type in the rule name. Base: The reference point of the object detection. Mode: Currently Enter rule only. Exclusive Area User can set up to 4 areas where the rules are not applied. Once selected, a purple line appears on the video preview window. Drag and drop the box at the desired position. User can change the shape of the box by dragging each corner to any form of a quadrilateral. NOTE: Video Content Analysis function cannot be used in conjunction with Motion Detection function. If you choose Enable video content analysis, motion detection function is automatically turned off. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 43

44 Face Detector This is used to detect a human face in the scene and makes a bounding box for the detected face. Select Enable face detector to activate the Face Detector. Set threshold for detectio sensitivity. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 44

45 2) Event Out SMTP( ) The network camera can be configured to send event and error messages via SMTP (Simple Mail Transfer Protocol). SMTP ( ) Setting: Select Enable to activate the SMTP operation. Sender: Enter an address to be used as the sender for all messages sent by the network camera. Interval: Represents the time interval of the notification when events occur several times. Aggregate events: Shows the maximum number of s sent within each interval. Use Mail Server: Check the box is you are using a mail server to receive event notification and image . Mail Server: Enter the host names (or IP addresses) for your mail server. Port: Enter the port number for your mail server. enable the sending of notifications and image messages from the network camera to predefined addresses via SMTP. Enable use(smtp) authentification: Check the box if your mail server requires authentication. User name/password: Enter the User name and Password as provided by your network administrator or ISP (Internet Service Provider). Login method: Choose a log-in method in the drop-down list: AUTH LOGIN / AUTH PLAIN SMTP ( ) Receiver: User can assign up to 8 receivers Receiver #: Enter an address. 45

46 SMTP ( ) Test: User can check the SMTP setting via a sample . Receiver: Enter an address and click the Test button to test that the mail servers are functioning and that the address is valid. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 46

47 FTP & JPEG When the network camera detects an event, it can record and save images to an FTP server. Images can be sent as attachments. Check the Enable FTP box to enable the service. FTP Setting Server: Enter the server s IP address or host name. Note that a DNS server must be specified in the TCP/IP network settings if using a host name. Port: Enter the port number used by the FTP server. The default is 21. Passive mode: Under normal circumstances the network camera simply requests the target FTP server to open the data connection. Checking this box issues a PASV command to the FTP server and establishes a passive FTP connection, whereby the network camera actively initiates both the FTP control and data connections to the target server. This is normally desirable if there is a firewall between the camera and the target FTP server. Remote directory: Specify the path to the directory where the uploaded images will be stored. If this directory does not already exist on the FTP server, there will be an error message when uploading. User name/password: Provide your log-in information. JPEG Setting Pre-event: A pre-event buffer contains images from the time immediately preceding the event trigger. These are stored internally in the server. This buffer can be very useful when checking to see what happened to cause the event trigger. Check the box to enable the pre-trigger buffer, enter the desired total length in seconds, minutes or hours, and specify the required image frequency. Post-event: This function is the counterpart to the pre-trigger buffer described above and contains images from the time immediately after the trigger. Configure as for pre-event. Prefix file name: This name will be used for all the image files saved. If suffixes are also used, the file name will take the form <prefix> <suffix>.<extension>. 47

48 Additional suffix: Add either a date/time suffix or a sequence number, with or without a maximum value. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 48

49 Alarm Out When the network camera detects an event, it can control external equipment connected to its alarm output port. Enable alarm out: If selected, the output becomes activated for as long as the event is active. Type: Select a type of NO (Normally Open) or NC (Normally Closed). When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 49

50 Audio Alert When the network camera detects an event, it can output a predefined audio data to external speaker. Check the Enable audio alert box to enable the service. Audio Alert Setting To use the audio alert with the network camera, an audio data file made by user must be uploaded from your PC. Provide the path to the file directly, or use the Browse button to locate it. Then click the Upload button. Up to 3 audio files are available. The total file size must be less than 512 KB. Audio Alert Test When the setup is complete, the audio output can be tested by clicking the Test button. To remove an audio file, select the file and click the Remove button. NOTE: For a proper operation of Audio Alert, full duplex must be enabled in the Audio settings page. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 50

51 Record When the network camera detects an event, it can record the video stream onto the Micro SD Memory (not supplied) or NAS (Network Attached Device) as a storage device. Check the Enable Record box to enable the service. Record Setting Overwrite: Click checkbox to overwrite the storage device; Continuous Record is available when not using an SD card. Stream Type: You can select Stream 1, Stream 2, or Stream 3. Stream1: H.264 or MPEG-4 data Stream2: MJPEG data Stream3: H.264 or MPEG-4 data Pre-event: Enter pre-event time value for the storage device pre-recording. Post-event: Enter post-event time value for the storage device pre-recording. Record Schedule You can set the weekly recording schedule for each day. Drag or click area by a box unit at first. Clicking the block toggles the recording between on and off. Click the All Select button to set a schedule for the entire week or a whole day, respectively. Device Setting Select the device type to be recorded in the drop-down list. according to selection. The screen changes 51

52 SD: Mounted SD card. CIFS: A file format for a NAS device. NFS: A file format for a NAS device. NOTE 1: Common Internet File System (CIFS) is a remote file access protocol that forms the basis for Windows file sharing, network printing, and various other network services. CIFS requires a large number of request/response transactions and its performance degrades significantly over high-latency WAN links such as the Internet. NOTE 2: Network File System (NFS) is a network file system protocol, allowing a user on a client computer to access files over a network in a manner similar to how local storage is accessed. NFS, like many other protocols, builds on the Open Network Computing Remote Procedure Call (ONC RPC) system. The CIFS screen displays as below. Address: Enter IP address for NAS device. Remote Directory: Enter directory or folder location to be recorded in the NAS device. Capacity: Enter the capacity of storage to be used. This must be less than the total storage capacity. ID/Password: Enter ID and Password. The network camera will ask for these whenever you access NAS device. Check: Press the Check button to check the validity of Device Setting data. Format: Click the Format button to format SD card. Device Information: Show current SD card information. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 52

53 XML Notification When the network camera detects an event, Notification server is used to receive notification messages as a type of XML data format. Check the box to enable the service. XML Notification Setting: Notification server URL: The network address to the server and the script that will handle the request. Notification server port: The port number of the notification server. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 53

54 Boost The Boost feature is used in conjunction with event detection. When this feature is turned ON, the Frame rate and Bit rate in the boost condition can be set to a different value than the ones in the normal condition field. When an event is detected, the camera will boost the Frame rate and Bit rate from the normal condition to this boosted level for the duration of the event. Check the box to enable the service. Boost Setting: You can set the condition in Normal and Boost mode. Boot Stream: Select a video stream for each condition in the drop-down list. Frame rate: Select a frame refresh rate per second for each condition in the drop-down list. Bit rate control: Select VBR or CBR in the drop-down list in Normal Condition. You cant change it in Boost Condition. Bit rate: Select a value for each condition in the drop-down list. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 54

55 Notification Server When the network camera detects an event, the Notification Server is used to receive uploaded image files and/or notification messages. Check the box to enable the service. Notification Server Setting: Type: User can select message transmission type among HTTP, HTTPS, TCP, and UTP. URL: The network address to the server and the script that will handle the request. For example: Port: The port number of the server. User name/password: Provide your log-in information. Notification Server Test: When the setup is complete, the connection can be tested by clicking the Test button using the contents in Send message box. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 55

56 3) Event Map The event map allows you to change the settings and establish a schedule for each event trigger from the network camera; up to a max. 15 events can be registered. Click the Add button to make a new event map; a popup window displays as below. To change an existing event, select that event and click the Modify button; this same window will display and the information can be changed as required. Selecting an event and clicking Remove deletes the event. 56

57 General: Enter the name for a new event map. Event In: Select an event type in the drop-down list. Event Out: Select the addresses you want to notify via that an event has occurred. FTP: Select checkbox beside FTP to record and save images to an FTP server when an event has occurred. Alarm out: Check this box to enable the alarm out. Audio Alert: Select an Audio Alert file as the Network Transmitter output when audio alert event triggered. The Audio Alert file must first be configured on the Event In page. XML Notification: It sends XML messages to an Notification server that listens for these. The destination server must first be configured on the Event In page. Boost: When an event has occurred, the camera will boost the Frame rate and Bit rate from the normal condition to this boosted level for the duration of the event. Check the box to enable the Function. Record: Record video stream when an event has occurred. The Record option must first be configured on the Event Out page. Notification Server: It sends notification messages to teh notification server that listens for these. The destination server must first be configured on the Event In page. Enter a message you want to send. When the settings are complete, click OK button to save the settings, or click Cancel button to clear all of the information you entered without saving it. 57

58 3.6.6 System 1) Information You can enter the system information. This page is very useful when you require device information after installation. Device Name Configuration: Enter the device name. Location Configuration: Enter the location information. locations. You can enter up to four When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 58

59 2) Security Users User access control is enabled by default when the administrator sets the root password on first access. New users are authorized with user names and passwords, or the administrator can choose to allow anonymous viewer login to the Live View page, as described below: User Setting: Check the box to enable anonymous viewer login to the network camera without a user account. When using the user account, users have to log-in at every access. User List Setting: This section shows how to register a user account. Enter a user name and password to be added, and register them by pressing the Add button. You will see the pop-up window as below. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 59

60 HTTPS For greater security, the network camera can be configured to use HTTPS (Hypertext Transfer Protocol over SSL (Secure Socket Layer)). Then all communication that would otherwise go via HTTP will instead go via an encrypted HTTPS connection. HTTPS Connection Policy: Choose the form of connection you wish to use from the drop-down list for the administrator, Operator and Viewer to enable HTTPS connection (set to HTTP by default). HTTP HTTPS HTTP & HTTPS Upload Certificate: To use HTTPS for communication with the network camera, an official certificate issued by a CA (Certificate Authority) must be uploaded from your PC. Provide the path to the certificate directly, or use the Browse button to locate it. Then click the Upload button. Please refer to the home page of your preferred CA for information on where to send the request. For more information, please see the online help. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 60

61 IP Filtering Checking the Enable IP address filtering box enables the IP address filtering function. Up to 256 IP address entries may be specified (a single entry can contain multiple IP addresses). Click the Add button to add new filtered addresses. When the IP address filter is enabled, addresses added to the list are set as allowed or denied addresses. All other IP addresses not in this list will then be allowed or denied access accordingly, that is, if the addresses in the list are allowed, then all others are denied access, and vice versa. Also see the online help for more information. NOTE: Users from IP addresses that will be allowed must also be registered with the appropriate access rights. This is done from Setup > System > Security > Users. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 61

62 OpenVPN OpenVPN is a Virtual Private Network using OpenSSL authentication. User can set the camera in either Server mode or Client mode. OpenVPN Server Mode 1. Select Enable openvpn activates mode selection buttons. Choose Server mode, then Server Mode Configuration appears where you can configure Server Mode Settings. 2. In Server Mode Configuration, you can setup Protocol type, Port number, LZO compression usage, and Renegotiation time, as well as download Server certificate file. Choose Protocol type between UDP and TCP, UDP is preferred. Type in Port number you want to use, default is Default Renegotiation time is 3600 seconds, and 0 means no verification. Use LZO compression determines whether to use cypher compression in connection or not. CA certificate is the certification file issued by Server for Client setup. 3. After finishing setup, click Save button and then the camera operates as an Open- VPN Server. 62

63 OpenVPN Client Mode 1. Select Enable openvpn activates mode selection buttons. Choose Client mode, then Client Mode Configuration appears where you can configure Client Mode Settings. 2. In Client Mode Configuration, you can setup Server URL, Protocol type, Port number, LZO usage, and Renegotiation time. Server URL sets OpenVPN IP address. Protocol type, Port number, and LZO setting must match Server setting. Default Renegotiation time is 3600 seconds, and 0 means no verification. Upload CA certificate issued by Server. 3. Select authentication method between User authentication and Machine authentication. For Machine authentication, upload client certificate and client key provided by Server. For User authentication, type in registered ID and Password. 4. After finishing setup, click Save button and then the camera operates as an Open- VPN Client. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 63

64 3) Date & Time Current Server Time This displays the current date and time (24h clock). The time can be displayed in 12h clock format (see below). New Server Time Time zone Select your time zone from the drop-down list. If you want the server clock to automatically adjust for daylight savings time, check the box Automatically adjust for daylight saving time changes. Time mode: Select the preferred method to use for setting the time: Synchronize with computer time: Sets the time from the clock on your computer. Synchronize with NTP Server: The network camera will obtain the time from an NTP server every 60 minutes. Set manually:allows you to manually set the time and date. Date & Time Format Specify the formats for the date and time (12h or 24h) displayed in the video streams. Select Date & Time format from the drop-down list. Date Format: Specify the date format. YYYY: Year, MM: Month, DD: Day Time Format: Specify the date format. 24 Hours or 12 Hours NOTE: If using a host name for the NTP server, a DNS server must be configured under TCP/IP settings. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 64

65 4) Network Basic IP Address Configuration: Obtain IP address via DHCP: Dynamic Host Configuration Protocol (DHCP) is a protocol that lets network administrators centrally manage and automate the assignment of IP addresses on a network. DHCP is enabled by default. Although a DHCP server is mostly used to set an IP address dynamically, it is also possible to use it to set a static, known IP address for a particular MAC address. To obtain IP address via DHCP, check the radio button. Use the following IP address: To use a static IP address for the network camera, check the radio button and then make the following settings: IP address: Specify a unique IP address for your network camera. Subnet mask: Specify the mask for the subnet the network camera is located on. Default router: Specify the IP address of the default router (gateway) used for connecting devices attached to different networks and network segments. IPv6 Address Configuration Check this Enable IPv6 box to enable IPv6. Other settings for IPv6 are configured in the network router. DNS Configuration DNS (Domain Name Service) provides the translation of host names to IP addresses on your network. Check the radio button to obtain DNS server via DHCP or set the DNS server. 65

66 Obtain DNS Server via DHCP: Automatically use the DNS server settings provided by the DHCP server. Use the following DNS server address to enter the desired DNS server by specifying the following: Domain name: Enter the domain(s) to search for the host name used by the network camera. Multiple domains can be separated by semicolons (;). The host name is always the first part of a Fully Qualified Domain Name, for example, myserver is the host name in the Fully Qualified Domain Name myserver.mycompany.com where mycompany.com is the Domain name. DNS servers: Enter the IP addresses of the primary and secondary DNS servers. Host Name Configuration Host Name: Enter the host name to be used as device information in the client software or SmartManager. Services HTTP port: Enter a port to receive a service through the HTTP. Default port number is 80. HTTPS port: Enter a port to receive a service through the HTTPS. Default port number is 443. RTSP port: Enter a port to receive a service through the RTSP. Default port number is 554. ARP/Ping Setting Enable ARP/Ping setting: The IP address can be set using the ARP/Ping method, which associates the unit s MAC address with an IP address. Check this box to enable the service. Leave disabled to prevent unintentional resetting of the IP address. Link Speed Control Link Speed: User can select either 10Mbps or 100Mbps. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 66

67 DDNS Internet DDNS (Dynamic Domain Name Service) When using the high-speed Internet with the telephone or cable network, users can operate the network camera on the floating IP environment in which IPs are changed at every access. Users should receive an account and password by visiting a DDNS service like Enable DDNS: Check to have DDNS service available. DDNS Server: Select the DDNS server. Registered host: Enter an address of the DDNS server. Username: Enter an ID to access to the DDNS server. Password: Enter a password to be used for accessing the DDNS server. Confirm: Enter the password again to confirm it. Maximum time interval: Set a time interval to synchronize with the DDNS server. Select the time interval from the drop-down list. Register local network IP address: Register a Network Video Server IP address to the DDNS server by checking the box and enter the Registered IP address. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 67

68 RTP Create a setting for sending and receiving an audio or video on a real-time basis. These settings are the IP address, port number, and Time-To-Live value (TTL) to use for the media stream(s) in multicast H.264 format. Only certain IP addresses and port numbers should be used for multicast streams. Port Range Start/End port: Enter a value between 1024 and Multicast (Stream1/Stream2/Stream3/Audio/Meta) This function is for sending Video, Audio, and Meta Data to Multicast group. Enable Multicast: Check the box to enable multicast operation. Multicast destination IP: Enter an IP between and RTP port: Enter a value between 1024 and RTP TTL: Enter a value between 1 and 255. If a network status is smooth, enter a lower value. However, if a network status is poor, enter a higher value. When there are many network cameras or users, a higher value may cause a heavy load to the network. Consult with a network manager for detailed information. Always enable multicast: Check the box to start multicast streaming without opening an RTSP session. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 68

69 UPnP The network camera includes support for UPnP. UPnP is enabled by default, so the network camera is automatically detected by operating systems and clients that support this protocol. Enter a name in the Friendly name field. NOTE: UPnP must be installed on your workstation if running Windows XP. To do this, open the Control Panel from the Start Menu and select Add/Remove Programs. Select Add/Remove Windows Components and open the Networking Services section. Click Details and then select UPnP as the service to add. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 69

70 QoS Quality of Service (QoS) provides the means to guarantee a certain level of a specified resource to selected traffic on a network. Quality can be defined as a maintained level of bandwidth, low latency, and no packet losses. The main benefits of a QoS-aware network are: 1. The ability to prioritize traffic and thus allow critical flows to be served before flows with lesser priority. 2. Greater reliability in the network, due to the control of the amount of bandwidth an application may use, and thus control over bandwidth races between applications. DSCP Settings For each type of network traffic supported by your network video product, enter a DSCP (Differentiated Services Code Point) value. This value is used to mark the traffics IP header. When the marked traffic reaches a network router or switch, the DSCP value in the IP header tells the router or switch which type of treatment to apply to this type of traffic, for example, how much bandwidth to reserve for it. Note that DSCP values can be entered in decimal or hex form, but saved values are always shown in decimal. The following types of traffic are marked; enter a value for each type of traffic used: Live Stream DSCP Event/Alarm DSCP Management DSCP Automatic Traffic Control Check the box to enable automatic traffic control. Set a limitation on user network resources by designating the maximum bandwidth. Select either the Maximum bandwidth or Automatic framerate radio button. Maximum bandwidth: When sharing other network programs or equipment, it is possible to set a limitation on the maximum bandwidth in the unit of Mbit/s or kbit/s. 70

71 Automatic frame rate: Selected if not influenced by a network-related program or equipment without a limitation on the network bandwidth. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 71

72 NAT (Port Mapping) NAT Settings NOTES: Enable: Check this box to enable NAT traversal. When enabled, the network camera attempts to configure port mapping in a NAT router on your network, using UPnP. Note that UPnP must be enabled in the network camera (see System Network UPnP). Automatic setting: When selected, the network camera automatically searches for NAT routers on your network. Manual setting: Select this option to manually select a NAT router and enter the external port number for the router in the field provided. If you attempt to manually enter a port that is already in use, an alert message will be displayed. When the port is selected automatically it is displayed in this field. To change this enter a new port number and click Save. For NAT (port mapping) to work, this must be supported by the broadband router. The broadband router has many different names: NAT router, Network router, Internet Gateway, Broadband sharing device or Home firewall, but the essential purpose of the device is the same. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 72

73 Zeroconf Zero configuration networking (zeroconf) is a set of techniques that automatically creates a usable Internet Protocol (IP) network without manual operator intervention or special configuration servers. Zero configuration networking allows devices such as computers and printers to connect to a network automatically. Without zeroconf, a network administrator must set up services, such as Dynamic Host Configuration Protocol (DHCP) and Domain Name System (DNS), or configure each computer s network settings manually, which may be difficult and timeconsuming. Zeroconf is built on three core technologies: Assignment of numeric network addresses for networked devices (link-local address auto configuration) Automatic resolution and distribution of computer hostnames (multicast DNS) Automatic location of network services, such as printing devices through DNS service discovery. Click the checkbox to enable Zeroconf. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 73

74 Bonjour The network camera includes support for Bonjour. When enabled, the network camera is automatically detected by operating systems and clients that support this protocol. Click the check box to enable Bonjour. Enter a name in the Friendly name field. NOTE: Also known as zero-configuration networking, Bonjour enables devices to automatically discover each other on a network, without having to enter IP addresses or configure DNS servers. (Bonjour is a trademark of Apple Computer, Inc.) When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 74

75 5) Language Select a user language. The language choices are English, Korean, French, Russian and Chinese. When the settings are complete, click Save button to save the settings, or click Reset button to clear all of the information you entered without saving it. 75

76 6) Maintenance Maintenance: Restart: The unit is restarted without changing any of the settings. Use this method if the unit is not behaving as expected. Reset: The unit is restarted and most current settings are reset to factory default values. The settings that are not affected are: the boot protocol (DHCP or static) the static IP address the default router the subnet mask the system time Default: The Default button should be used with caution. Pressing this will return all of the network camera s settings to the factory default values (including the IP address). Update: Upgrade your camera by importing an upgrade file and pressing the Upgrade button. During the upgrade, do not turn off the power of the network camera. Wait at least five minutes and then try to access the camera again. Backup: Save the setting values that users have entered to the network camera to a user PC. Restore: Import and apply a setting value previously saved to a user PC. Optics: Pressing Calibrate button performs zoom and focus calibration and sets the lens to the default position. NOTE: Backup and Restore can only be used on the same unit running the same firmware. This feature is not intended for multi-configurations or for firmware upgrades. 76

77 7) Support The support page provides valuable information on troubleshooting and contact information, should you require technical assistance. Logs: The network camera supports system and event log information. Click the System Log button to get the system log data or the Event Log button to get information on events. Reports: Server Report: Click the Server Report button to get the important information about the servers status; this should always be included when requesting support. Parameter List: Click the Parameter List button to see the units parameters and their current settings. Health Check: System Check: Click the System Check button to get the important information about the cameras system resources. You can see the pop-up window below. Media Check: Click the Media Check button to get the information about the cameras video and audio stream. You can see the pop-up window below. 77

78 Networks Check: Click the Network Check button to get the information about the cameras network setting and traffic. You can see the pop-up window below. Hardware Check: Click the Hardware Check button to diagnose the cameras hardware like video. 78

79 3.7 Help The Help information window will be provided as a popup window so that users can open and read it without needing to log-in. It will offer a description of the setting and Help page so that users can manipulate the network camera without a reference to the manual. 79

80 3.8 Resetting to the factory default settings To reset the network camera to the original factory settings, go to the Setup > System > Maintenance web page (described in System > Maintenance of Users Manual) or use the Reset button on the network camera, as described below: Using the Reset button: Follow the instructions below to reset the network camera to the factory default settings using the Reset button. 1. Switch off the network camera by disconnecting the power adapter. 2. Press and hold the Reset button with a straightened paperclip while reconnecting the power. 3. Keep the Reset button pressed until the Status indicator blink. 4. Release the Reset button. 5. When the Power Indicator changes to Green (may take up to 40 seconds), the process is complete and the network video camera has been reset. 6. The network camera resets to factory defaults and restarts after completing the factory reset. CAUTION: When performing a Factory Reset, you will lose any settings that have been saved. (Default IP ) 80

81 A Appendix A.1 Troubleshooting Troubleshooting if problems occur, verify the installation of the network camera with the instructions in this manual and with other operating equipment. Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information. Problems/Symptoms The camera cannot be accessed by some clients. The camera works locally, but not externally. Poor or intermittent network connection. The camera cannot be accessed via a host name. Not possible to log in. No image using Refresh and/or slow updating of images. Images only shown in black & white. Blurred images. Poor image quality. Rolling dark bands or flickering in image. H.264 not displayed in the client. Multicast H.264 not displayed in the client. Multicast H.264 only accessible by local clients. Color saturation is different in H.264 and Motion JPEG. Video cannot be recorded. Possible Causes or Corrective Actions If using a proxy server, try disabling the proxy setting in your browser. Check all cabling and connectors. Check if there are firewall settings that need to be adjusted. Check if there are router settings that need to be configured. If using a network switch, check that the port on that device uses the same setting for the network connection type (speed/duplex). Check that the host name and DNS server settings are correct. When HTTPS is enabled, ensure that the correct protocol (HTTP or HTTPS) is used. When attempting to log in, you may need to manually type in http or https in the browser s address bar. If images are very complex, try limiting the number of clients accessing the camera. Check the Video & Image setting. Refocus the camera. Increased lighting can often improve image quality. Check that there is sufficient lighting at the monitored location. Check all image and lighting settings. Try adjusting the Exposure Control setting under AE and AWB part. Check that the correct network interface is selected in the Video & Image/Stream. Check with your network administrator that the multicast addresses used by the camera are valid for your network. Check that the Enable multicast checkbox are enabled in the System/Network/RTP tab. Checks with your network administrator to see if there is a firewall preventing viewing. Check if your router supports multicasting, or if the router settings between the client and the server need to be configured. The TTL value may need to be increased. Modify the settings for your graphics adapter. Please see the adapter s documentation for more information. Check that the Micro-SD card is inserted properly. Check that the Micro-SD card is formatted properly. 81

82 A.2 Alarm Connection The following connection diagram gives an example of how to connect a network camera. A.3 Preventive Maintenance Preventive maintenance allows detection and correction of minor that faults before they become serious and cause equipment failure. Every three-month, perform the following maintenance. 1. Inspect all connection cables for deterioration or other damage. 2. Clean components with a clean damp cloth. 3. Verify that all the mounting hardware is secure. 82