POS500/505 with B75 M/B Installation Guide Point-of-Sale Hardware System

Transcription

1 POS500/505 with B75 M/B Installation Guide Point-of-Sale Hardware System July 2003 V1.0

2 1. Accessory External Floppy Cable External IDE Cable Power Cord Y Cable(Keyboard & Mouse) Serial Cable DIO Cable Warranty Card Drivers Bank 2

3 The following drivers in the folders of Driver Bank are necessary for driver installation: Folder Driver Function Acrobat Acrobat Reader Installation BIOS Tool BIOS Update Tool CDROMDrv CDROM driver installation (for DOS) Common Elo_Touch Touch screen driver Installation LAN_drive LAN driver installation Netmos Enable COM5/COM6 Smart Card Smart Card driver installation Cash Drawer Cash Drawer Test Program VFD Customer Display Test Program Audio Audio driver installation B75 Linux Linux driver installation VGA_Win2KXP VGA driver installation in Win2KXP VGA_Win98ME VGA driver installation in Win98ME Card Reader Card Reader Test Program Test Utility Cash Drawer Cash Drawer Test Program VFD Customer Display Test Program 3

4 2. I/O Function 2.1 Front View # Function # Function 1 LCD Touch Module 3 Card Reader 2 Power Switch & Ext. IDE Connector 4 Ext. FDD Connector & CF Socket 2.2 I/O port # Function # Function # Function # Function # Function 1 KB / Mouse 3 COM1 5 COM3 7 COM6 9 USB1&2 2 LPT 4 COM2 6 COM4 8 Cash Drawer 10 LAN 4

5 3. Specification Model No. POS500 POS505 Motherboard B75 Core Logic SIS 650 (SIS 650 & SIS 961 ), Supports 400MHz FSB CPU Processor Intel P4 processor mp478-pin Memory 2 x DIMM up to 2GB DDR SDRAM 200/266 BIOS AWARD PnP 2Mbit VGA Display Built-in Core Logic VGA memory Share Memory 8MB 64MB I/O Controller W83697HF x 2 supports COM x 4, USB x 2, LPT1 x 1 NetMos/PCI 9835 supports COM5-COM 6 Ethernet Controller RTL 8100BL 10/100Mb Fast Ethernet controller Digital I/O controller 4 Input/Output Digital Video Output SIS302LV Mainboard dimension 23.1 x 21.4cm (W x D) I/O Ports Front Bezel: Ext. IDE Connector Rear Panel:1 PS2 port with Y Cable for PS2 keyboard and PS2 Mouse Centronics Printer port x 1 DB-9M RJ-45 RS-232 serial port (COM1/COM2) x 2 10-pin RJ-45 RS-232 serial port (COM3/COM4/COM6) x 3 COM4 default for Card Reader, COM5 default for Touch Screen COM6 for Pole Display, COM1 & COM6 pin 1 supports +5V/+12V Cash Drawer x 1, RJ-45 LAN x 1, USB x 2 Compact Flash Socket supported HDD drive Optional One 3.5 HDD FDD connector Ext. 40-pin connector with DC power Touch Panel 12.1 TFT LCD Panel, max resolution 800 x 600, brightness : 180nits 12.1 resistive touch panel view Angle TFT LCD Panel, max resolution 1024 x 768 brightness : 250nits 15 resistive touch panel view Angle 0-60 Card Reader Optional Magnetic strip and barcode card reader keyboard or serial (Horizontal Type) Card Reader W/I-button (Vertical Type) Customer Display Second Display Power Supply Operation Temperature 5 35 C EMI/EMS CE Class-A interface type 3-track Optional keyboard or serial interface 3-track Card Reader built-in keyboard type I-button Optional keyboard or serial interface type 3-track Card Reader Optional Keyboard type I-button w/o Card Reader Optional VFD / Graphic type Pole Display Optional VFD / Graphic type Customer Display / Fixed Type Display Optional 8.4 /10.4 /12.1 TFD LCD Display FT-8200 Internal ATX 200W Power Supply +5V/20A, +12V/10A (5V/+12V max185w), 5VSB /1.5A, -12V/0.5A, -5V/0.5A, 5

6 EMI/EMS FCC(This device complies with part 15 of the FCC rules. Operation is subject to the following two condition: (1)This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. ) System Dimension 330 (W) x 320 (D) x 240(H) mm (W) x ~ (D) x ~ (H) mm Weight N.W. 6.5kgs/ G.W 7.5 kgs N.W. 9kgs / G.W. 11kgs 3.1 System Memory Combination POS500/505 RAM Size Slot 128MB 256MB 512MB 1024MB 2048MB DDR1 X X X DDR2 128 X 128 X X Please note that DDR1 of POS500 does not support RAM over 29 mm in height. 4. Peripherals Installation 4.1 Install External FDD a. Connect the FDD cable from 40 pin FDD connector left side of LCD module.. b. Enter "Integrated Peripherals" of the Main Menu of BIOS CMOS Setup Utility. c.move the arrow key downward to the "Onboard Super IO Device" item d. Move the arrow key downward to the "FDC Controller" item. Use "Page Up" or "Page Down" key change to Enable 6

7 e. Enter "Standard CMOS Features" of the Main Menu of BIOS CMOS Setup Utility. f. Move the arrow key downward to the "Drive A" item. g. Use "Page Up" or "Page Down" key for FDD Installation. Make sure you save the changes by pressing F10 key or moving to "Save & Exit Setup." 4.2 Install External IDE Device a. Take out the manufacturer s IDE cable provided in the accessory bag, connect the second HDD or CD-ROM drive to the 50-pin Header as hidden in the Front Cover of the Base Stand. b. Connect the IDE cable from either the second HDD or CD-ROM drive to the 50 pin Header hidden in the Front Cover of the Base Stand. 7

8 4.3 Install MCR Module (optional) The optional MCR (Magnetic Card Reader) unit is tested and can be supplied at your request. This MCR is removed during transportation and can be connected by the user. The manufacturer offers two types of MCR Module, either by the Serial type or keyboard type. If the product barcode is P , the POS system you order is a Serial type, P stands for a keyboard type. If you order POS system with no MCR, the jumper setting will be set for a serial type. A keyboard type MCR must be mounted onto the POS system if jumpers are set for keyboard type MCR, otherwise the keyboard device will malfunction. Terminator a. Install the MCR module to the right side of System Bay Module and lock it with two screws. b. If you select a keyboard type MCR and the system does not connect a standard P/S2 keyboard, please insert the Terminator for simulate and instead of the P/S2 Keyboard. 4.4 Install Pole Display Module (optional) The POS system is equipped with an interface for a connection to a Pole Display Module. Please refer to COM6 of CN7 of jumper setting section. a. Remove Pole Display cover from POS system unit by fingers. b. Install Pole Display cover kit onto POS system unit. 8

9 c. Install Pole Display flat cable inside Pole Display Tube. Use either two or one tube. d. Connect Pole Display cable RJ-45 connector to COM6 of POS system. 4.5 Install a Compact Flash Card You can install a compact flash card At he left side of the LCD panel. 9

10 4.6 Install Cash Drawer You can install a cash drawer through the Cash Drawer port Cash Drawer Pin Assignment Pin Signal Pin Signal 1 IN0 6 OUT3 2 IN1 7 OUT2 3 IN2 8 OUT1 4 IN3 9 OUT0 5 GND 10 12V Data out address(200h) Data in address(201h)

11 4.7 Install Second Display a. Get the VGA cable through the supporter of the second display. b. Insert the male head of the VGA cable into the VGA port. c. Mount the second display on the rear of the system and tighten the three screws on the supporter (The third one is behind the supporting pole). d. Insert the other end of the VGA cable (female) into the VGA port of the system to establish the connection. 11

12 5. Driver Installation The following procedures are for Windows 2000, other platforms are similar. 5.1 Netmos a. Indicate the location of the Netmos driver b. Choose Nm2kMf in the Locate File window. c. Click OK on the Files Needed window. d. Now the Netmos driver is installed. 12

13 5.2 Elo_Touch a. Click "COMMON" on the POS driver window. b. Click "Elo_Touch" on the COMMON window. c. Choose the OS to be installed with Elo _Touch driver. d. Click Setup on the EloWin2000 window. e. Click Next on the Elo MonitorMouse for Windows 2000 Setup window. d. Choose COM5 and click Next on the Elo MonitorMouse for Windows 2000 Setup window. e. Click Finish on the Elo MonitorMouse for Windows 2000 Setup window. 13

14 f. Click Yes on the System Settings Change. g. After the computer restarted, touch the targets with your finger for alignment. h. Click Yes on the Check Video Alignment window. i. Click Finish on the Elo TouchSystem Setup window. j. If the cursor is not in sync with your finger tip, click Align to execute the alignment procedure again, or click OK k. Now the Elo_Touch driver is installed. 14

15 5.3 LAN-driver a. Click "COMMON" on the POS driver window. b. Click Lan_driver on the COMMON window. c. Click REL8100 on the Lan_driver window. d. Click Setup on the REL8100 window. e. Click Next on the InstallShieild Wizard. f. Click Finish on the InstallShield Wizard. g. Now the Lan_driver is installed. 15

16 5.4 VGA a. Click B75 on the POS driver window. b. Click VGA_Win2KXP on the B75 window. c. Click SETUP On the VGA_Win2KXP window. d. Click Next on the Welcome window. e. Click "Next" on the Setup Type window. f. Click "Next" on the Select Program Folder window.. 16

17 g. Click "Next" on the Select Copying Files window. h. Click "Finish" on the Setup Complete window. i. Now the VGA driver is installed. 17

18 5.5 Serial Mouse Driver for WINXP a. Go to the window of Device Manager, click Action and then Update Driver b. Select Install from a list or specific location (Advanced) then Click NEXT. c. Select Don t search, I will choose the driver to install then Click NEXT. d. Select Standard mouse types and Standard Serial Mouse, then Click NEXT." e. Click Finish, then reboot the system. f. Now you will see a new Standard Serial Mouse in Device Manager. 18

19 6. Jumper Setting 6.1 Location of Main Board CN3 CN2 CN4 JP1 FAN1 DDR1 DDR2 CN1 SKT1 CN5 PWR1 JP3 CPU1 IDE1 CN6 CN7 IDE2 CN8 U4 CN9 U13 JP6 U20 CN10 JP4 CN13 JP5 BZ1 U23 PWR2 3 4 U21 U19 U26 PCI1 JP8 BAT1 U41 U39 U42 U38 CN11 U40 19

20 6.1.1 CPU FAN Speed Control * Factory Default Setting Function JP1 *Full Speed 1-2 Middle Speed 3-4 Slow Speed 5-6 System Control Power Mode Selection Function JP3 JP5 *ATX Mode / 3-4 / 5-6 AT Mode / Clear CMOS Function JP8 Clear 2-3 *Normal Pin 1 Function of COM Port Selection : JP COM PIN Function Jumper *DCCD V 3-4 5V 5-6 *RI V V *DCCD V V *RI V V

21 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions carefully. Save these instructions for future reference. 2. Follow all warnings and instructions marked on the product. 3. Do not use this product near water. 4. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 5. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided. 6. This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. 7. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. 8. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Caution on Lithium Batteries Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer s instructions. 21