Installation Manual of DS-9600NI-H8 DS-9600NI-H8. Installation Manual UD.7L0202A1730B01

Transcription

1 DS-9600NI-H8 Installation Manual UD.7L0202A1730B01 1

2 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. Before you start, read the following statement first: This manual, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice. We assume no responsibility or liability for any errors or inaccuracies that may appear in the book. During using the surveillance equipment, please obey the applicable laws and regulatory requirements. Using the equipment for monitoring people s privacy for other improper purpose is regarded as illegal. The installation manual is applicable to DS-9600NI-H8 series.

3 Preventive and Cautionary Tips Before connecting and operating your NVR, please be advised of the following tips: It is not recommended to replace the batteries by the user, since improper use or replacement of the battery may result in hazard of explosion. If needed, replace with the same or equivalent type only. Ensure unit is installed in a well-ventilated, dust-free environment. Ensure at least 2cm (~0.75-inch) of space between two devices. Environmental temperature should be within the range of 0 ºC ~ 50 ºC (32 ºF ~ 122 ºF). Environmental humidity should be within the range of 10% ~ 90%. The dust on the circuit board inside the device will short circuit the board. Please use the soft brush to clean the circuit board, the connector, the chassis and the fan. You can also use the water-diluted neutral detergent to wipe away the dust and then dry the components. The volatile solvents, such as alcohol, benzene or thinner, are not allowed to clean the device. Ensure no danger will be caused because of the uneven mechanical load. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter. Unit is designed for indoor use only. Keep all liquids away from the NVR. Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive electronics within the unit. Use the NVR in conjunction with an UPS if possible. Power down the unit before connecting and disconnecting accessories and peripherals. A factory recommended HDD should be used for this device. Ensure the NVR is grounded.

4 Table of Contents Chapter 1 Overview... 1 Chapter 2 Chipset Features... 2 Chapter 3 Interface Description Front Panel Introduction Rear Panel Introduction Motherboard Introduction... 5 Chapter 4 Operating System Installation Installing a HDD Setting Boot Sequence Installing Operating System Installing Driver... 9 Chapter 5 Specification... 10

5 Chapter 1 Overview DS-9600NI-H8 is an embedded development platform. It is designed for professional digital surveillance. As to the features, it has a well performance in CPU processing, encoding and decoding, and storage capability. Due to the openness of IA structure, various PC application software can be applied to the product, and providing a flexible NVR solution for the software developers or system integrators. Developing Support: Support Windows 7, Windows 8 and Linux operating system. Provide system SDK and open-source DEMO for programmable front panel button, LED & alarm I/O configuration. Provide third-party drivers including audio card driver, network interface driver, chipset driver, graphics card driver, etc.. Application Software Partners Windows Operating System SDK, Demo and Driver Third Party Drivers DS-9600NI-H8 Hardware Figure 1. 1 Development Support 1

6 Chapter 2 Chipset Features Intel i3-330e 2.13GHz CPU with low power consumption and high performance. Support flexible development due to IA structure. Two 1000M Ethernet interfaces, support multiple network cameras connection. H.264 hardware compression. Programmable front panel button & LED configuration. Compact and flexible structure design. 2

7 Chapter 3 Interface Description 3.1 Front Panel Introduction POWER ALARM Tx/Rx HDD READY ARCHIVE Figure 3. 1 View of Front Panel Table 3. 1 Description of Front Panel No. Name Description Power Power indicator is red in standby status and green if the device is running. Alarm The indicator status is programmable via system SDK. 1 Status LED Indicators Tx/Rx HDD Tx/Rx blinks in red or green color when there is network data transmission. HDD indicator blinks when hard disk writing or reading. Ready The indicator status is programmable via system SDK. Archive The indicator status is programmable via system SDK. 2 Backup Button The button response is programmable via system SDK. 3 USB Ports 4 Power Button 5 Channel Status Indicators Universal Serial Bus (USB) 3.0 ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). Press the Power button for over 1.3 seconds to shut down the device, yet if you press more than 4 seconds, the device will be shutdown forcedly. The indicator status is programmable via system SDK. The indicator color can be set as red or green color. 6 Front Panel Lock You can lock or unlock the panel by the key. 3

8 3.2 Rear Panel Introduction Figure 3. 2 Rear Panel View Table 3. 2 Rear Panel Description No. Item Description 1 USB Interface Universal Serial Bus (USB) 3.0 ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 2 AUDIO IN RCA connector for audio input. 3 AUDIO OUT RCA connector for audio output. 4 VGA DB9 connector for VGA output. Display local video output and menu. 5 HDMI1/HDMI2 HDMI/HDMI2 video output connectors. 6 RS-232 Interface Connector for RS-232 devices. 7 esata Connects external SATA HDD, CD/DVD-RW. 8 LAN Interface 2 RJ /100 /1000 Mbps self-adaptive Ethernet interfaces. 9 Termination Switch RS-485 termination switch. Up position is not terminated. Down position is terminated with 120Ω resistance. RS-485 Interface Connector for RS-485 devices. T+ and T- pins connect to R+ and R- pins of PTZ receiver respectively. 10 Controller Port D+, D- pin connects to Ta, Tb pin of controller. For cascading devices, the first NVR D+, D- pin should be connected with the D+, D- pin of the next NVR. 11 ALARM IN Connector for alarm input. ALARM OUT Connector for alarm output. 12 GROUND Ground (needs to be connected when NVR starts up). 13 AC 100V ~ 240V AC 100V ~ 240V power supply. 14 POWER Switch for turning on/off the device. 4

9 3.3 Motherboard Introduction Figure 3. 3 Motherboard View Table 3. 3 Motherboard Description No. Description Memory card slot. Memory card of capacity up to 8GB DDR3 can 1 be inserted. 2 esata interface. 3 Debug card interface. For the use of debugging and maintenance. 4 SATA interface for the operating system HDD. 5 Fan interface. 6 USB 2.0 interface for front panel, with 9 pins. 7 Standard ATX power interface, with 24 pins. 8 SATA interfaces for system storage. 5

10 Chapter 4 Operating System Installation 4.1 Installing a HDD Before you start: Before installing a hard disk drive (HDD), please make sure the power is disconnected from the NVR. A factory recommended HDD should be used for this installation. Steps: 1. Fasten the hard disk mounting handle to the hard disk with screws. Figure 4. 1 Installing Screws 2. Insert the key and turn in clockwise direction to open the panel lock. Figure 4. 2 Unlocking Front Panel 3. Press the buttons on the panel of two sides and open the front panel. 6

11 Figure 4. 3 Opening Front Panel 4. Insert the hard disk along the slot until it is placed into position. Figure 4. 4 Inserting the HDD 5. Repeat the above steps to install other hard disks onto the NVR. After having finished the installation of all hard disks, close the front panel and lock it with the key again. Figure 4. 5 Locking Front Panel 4.2 Setting Boot Sequence Purpose: When installing the operating system, you need to manually set the CD/DVD-ROM Drive as the first boot type. The default priority of boot sequence from high to low is: HDD8 > esata > USB. 7

12 Steps: 1. Enter BIOS interface when starting process by pressing F2 on keyboard. 2. Enter Advance settings interface by pressing direction buttons and Enter button on keyboard. Boot > Legacy > Normal Boot Menu > Advance Figure 4. 6 Boot Configuration Interface 3. Set the CD/DVD-ROM Drive as the first boot type. Figure 4. 7 Setting the Boot Type 4.3 Installing Operating System Before you start: If you use a SATA CD/DVD-ROM drive, connect it to the interface of esata. If you use a USB CD/DVD-ROM drive, connect it to any of the USB interfaces. If you use a SATA disk as the system disk, connect it to the eighth HDD slot, which is located at low-right corner after opening the front panel. The Windows 7 OS, Windows 8 OS and Linux OS can be installed on the NVR directly. Step: Insert the Windows installation CD and install the operating system. 8

13 4.4 Installing Driver Purpose: The NVR is attached with a driver installation program when delivery. The program is used for installing system driver, including motherboard chipset driver, audio card driver, graphics driver, etc.. And it is applicable to windows 7 and windows 8 of 32 bit and 64. Step: For the detailed steps, please refer to driver and SDK installation manual. After successfully installing the drivers, you can view the drivers listed in the Computer Management interface. Graphics Driver Network Driver Audio Driver Figure 4. 8 Drivers View 9

14 Chapter 5 Specification Model DS-9600NI-H8 Processor Type Intel Xeon Processor E v3 (8M Cache, 3.20 GHz) Memory Memory size 8GB 1, resolution: /30Hz HDMI output Video / Audio 1, resolution: /60Hz Output VGA output 1, resolution: /60Hz Audio output 1-ch, BNC (Linear, 1kΩ) Storage External Interface General 8 hot-swappable SATA 3.0 interfaces for 8 HDDs SATA Up to 6TB capacity of each disk esata 1 esata interface Audio in 1,BNC Network interface 2 RJ /100 /1000 Mbps self-adaptive Ethernet interfaces USB interface Front panel: 2 USB 2.0; Rear panel: 2 USB 3.0 Serial interface RS232, RS485 and KB interface Alarm in 16 Alarm out 4 (Expandable to 8) Power supply 100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz Consumption (without HDD or DVD-R/W) 250W Working temperature 0 ºC ~ +45 ºC Working humidity 10% ~ 90% Chassis 19-inch rack-mounted 2U chassis Dimensions (W D H) mm (17.5" 18.5" 3.5") Weight 8kg 10