ML200 Fanless Mini-ITX Enclosure

Transcription

1 ML200 Fanless Mini-ITX Enclosure Assembly Guide Version 1.1 PN: ML200 1

2 Table of Contents I. Product Description... 3 II. Included Parts... 3 III. Basic Chassis Assembly... 5 IV. Installation VI. Ordering Information

3 I. Product Description Marshalltown Thin-ITX mainboard. The enclosure is constructed from durable steel with an anodized aluminum extrusion top. Cooling is provided by a solid aluminum thermal block that keeps the system cool for an operating environment temperature range of 0 to 40 degrees Celsius. The ML200 provides access to a broad range of I/O, including two additional serial ports off the front panel via mainboard s pin headers, antenna jacks for Wi-Fi and Bluetooth cards, front The case includes mounting brackets with DIN-rail hole layout, HDD tray, and secure cabling for connecting storage devices. II. Included Parts Case and Components 1. Bottom of chassis 2. Top of chassis 3. Thermal block for CPU 4. Mounting brackets 5. HDD bracket 3

4 Hardware and Accessories (listed top to bottom, left to right) A. 6x M3x0.5, 4 mm silver PCB screws B. C. D. 4x Plastic support posts E. 4x Self-adhesive foot pads F. 1x Thermal paste G. 3x Plastic washers H. 1x Film for mainboard I. 1x Thermal pad for CPU block J. 1x Film for HDD K. 1x Right-angled SATA power cable (not pictured) L. 1x Right-angled SATA cable (not pictured) 4

5 III. Basic Chassis Assembly 2) Prep the mainboard by removing OEM heat sink. 3) Install four plastic support posts (D) from bottom side of board. Install three plastic spacer washers (G) only on the plastic posts shown in the picture below. Apply small dot of thermal paste (F) onto CPU. Be sure to mix paste well in package before applying. 5

6 4) Install thermal cooling block and ensure all four plastic support posts have fully engaged and clipped. Carefully peel dislodging the thermal pad. The thermal pad is very stretchy so peel slowly to prevent problems. 5) Install mainboard into chassis and secure with four mainboard screws (A). button and USB accessory board using two mainboard screws (A). Some units may have pre-installed boards. 7a) If COM ports are required, install two COM port cables into the chassis using hex screws. It will be necessary to twist out front panel knockouts. The inner most cable must be folded under the connector and out the side towards the button/ 6

7 USB accessory board to prevent cable pinching on the mainboard. The inner most COM cable plugs into the COM port on the mainboard next to the PCIe Mini Card slot. The out-bound COM cable plugs into the mainboard header closer to the front near the USB connectors. Ensure both cables are routed away from the aluminum cooling block. 7b) Alternate view of COM cabling layout. Note how the COM cables are situated to avoid interfering with mainboard s components and pin headers. 7

8 TA data and SATA power right angle connectors into the mainboard and lay across board. Install the hard drive bracket into the chassis over The cables shall pass through the tunnel under the tray near the back surface of the chassis. The HDD bracket has a tab that will seat under the thermal pad but on top of the CPU cooling block. Secure the bracket to the bottom chassis lower height the grip tab will interfere with the HDD bracket. The jumper is located directly behind the LAN port on the mainboard. 9) Alternate view of hard drive to show the orientation of the connectors. This also shows the hex posts for the COM ports. 8

9 shows mounting for both full and half-height cards. Inside views of antenna jacks are shown, too. 11) Install the top cover onto the chassis. Orientation does not matter. Squeeze together top and bottom lightly to ensure compression for cooling. 9

10 12) After bottom screws are secure, install six front and rear screws (C), three each side, along the top of the chassis. 13) Install mounting brackets on bottom of chassis using four black screws (C) provided. 14) Install self-adhesive mounting feet onto bottom side of chassis. Ensure surface is clean prior to securing. 10

11 15) Finished unit with brackets shown. 16) Back panel view of optional automotive DC-style locking power connector, SMA antenna holes and DC power barrel. 11

12 IV. Installation Mounting brackets are included with the enclosure. The brackets have both DIN-rail and quick bi-directional keyway slots Dimensional information for mounting is as follows: Case, Top View 12

13 Case, Side Views Item Description Dimensions (w x h x d) 185 x 32 x 205 mm (7.28 x 1.26 x 8.07 ) Material Powder-coated galvanized steel Extruded anodized aluminum top Cooling Power Access P4 panel mount, or DC jack via mainboard Antenna options Dual 0.25 holes on rear panel USB 2 USB panel mounts on front panel 4 USB 2.0 ports on back panel (via mainboard) RS RS-232 panel mount openings on front Storage Temperature / RH -20 C to 60 C Operating Environment Temperature (0-90% RH noncondensing) 0 C to 40 C RoHS Designed to conform to RoHS standards VI. Ordering Information Systems and components are available for purchase through Logic Supply. To order the case, please see the ML200 Case product page on the Logic Supply website or call , option 1 for project pricing. The case can be viewed here: If you would like to order the ML200 case with the Intel DN2800MT Thin-ITX mainboard, please see the AG150 system page or call us for project pricing. The system page can be viewed here: Part Number ML200 AG150 Description Fanless Mini-ITX Case Atom Fanless System 13