UWE-1707 SERIES CONTENTS OPERATION MANUAL ELECTRONIC WEIGHING INDICATOR 1. SPECIFICATIONS 2. INSTALLATION

Size: px

Start display at page:

Download "UWE-1707 SERIES CONTENTS OPERATION MANUAL ELECTRONIC WEIGHING INDICATOR 1. SPECIFICATIONS 2. INSTALLATION"

Simon Foster
6 years ago
Views:

1 UWE-1707 SERIES CONTENTS ELECTRONIC WEIGHING INDICATOR OPERATION MANUAL 1. SPECIFICATIONS PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE SCALE 2. INSTALLATION 3. ROUTINE OPERATION 4. TECHNICAL FUNCTIONS ( For technicians) AUGUST 1999 REV 2 5. CARE AND MAINTENANCE Specifications subject to change without prior notice

2 1. SPECIFICATIONS 1.1 GENERAL MODEL NO. UWE-1707 WEIGHT N.W.: 2.5 kgs G.W.: 3.5 kgs DIMENSIONS 250W X 150 H X 165 D (mm) POWER CONSUMPTION RECHARGEABLE BATTERY OR AC ADAPTOR (220/110VAC +/- 10% Hz) LESS THAN 0.5 Watts OPERATING C( C) TEMPERATURE OPERATING < 95% R.H. HUMIDITY 1.2 ANALOG SECTION ANALOG INPUT Sensitivity of 0.4uV at minimum, Full scale range of 15mV, Zero adjustment range of 2% of F.S.. EXCITING 5V DC +/- 5%, 150mA VOLTAGE INPUT IMPEDANCE 10M ohm (min.) LOAD CELLS 8(max.) MAX. DISPLAY 1/6,000 RESOLUTION TEMPERATURE Zero : +/- (0.3uV +/ % COEFFICIENT of the initial zero Offset voltage)/ 0 C Span: +/- 10 ppm / 0 C of rdg. NON-LINEARITY 0.016% of F.S. or less INPUT NOISE 0.4uV p-p SPAN Temp. compensation : +/ % F.S / 0 C Long-time drift: +/- 0.01% F.S. A/D CONVERTER Internal resolution: 40,000 counts External resolution: 6,000 divisions Conversion rate: 5 times per second 1.3 DIGITAL SECTION WEIGHT DISPLAY 5 1/2 digit LCD DIGIT HEIGHT 1 inch UNDER ZERO Minus sign - INDICATION ZERO Center of zero ANNUNCIATOR TARE Annunciate if the ANNUNCIATOR figures of weight is under HI.-GO-LO ANNUNCIATOR tare mode Checking high, go, low state if the limit values have been set-up Kg, Ib, %, pcs ANNUNCIATOR Measuring unit conversion by MODE key entry LO-BAT ANNUNCIATOR When sign appears, the scale needs to be recharged IN-CHARGE LED Indicate if the electricity supply is connected

2. INSTALLATION 2.1 UNPACKING Unpacking the scale carefully. In the package you shall find: 1. this manual 2. the instrument 3. the option, if there is any. 4. AC adaptor 5.

3 2. INSTALLATION 2.1 UNPACKING Unpacking the scale carefully. In the package you shall find: 1. this manual 2. the instrument 3. the option, if there is any. 4. AC adaptor 5. Accessory *keep the packing material if you might want to transport it again 2.2 BEST INSTALLATION REQUIREMENTS There are many surrounding factors, which will affect the workability of the scale such as vibration, static electricity, airflow, humidity. These factors should be noted when you install the scale. *Stable and/or not subject to vibration *Not exposed to direct sunlight *Away from areas containing corrosive gas *Dust-free *Temperature C *Humidity 95% or less *Away from other heavy duty electronic equipment, to avoid interference. *Away from heaters and air conditioners, to avoid sudden changes of temperature. 2.3 INSTALLATION PROCEDURES 1. Place the instrument in a location described above. 2. connect the instrument with load cells. 3. Ground the instrument. 4. Recharge the battery at least 10 full uninterrupted hours. 5. Calibration if necessary. 6. The scale is ready for operation. 2.4 LOAD CELL CONNECTION

3. ROUTINE OPERATION 1. OPERATION PANEL 2.Explanation of keys KEY NAME FULL NAME DESCRIPTION ON On & ZERO This key is used to ZERO switch on the scale and return the display to true zero.

4 3. ROUTINE OPERATION 1. OPERATION PANEL 2.Explanation of keys KEY NAME FULL NAME DESCRIPTION ON On & ZERO This key is used to ZERO switch on the scale and return the display to true zero. - can be used for display decrements when the scale is being set and calibrated. OFF OFF Press this key to switch off the scale. TARE TARE Press this key to + subtract the weight of the container placed on the platform. + can be used for display increments when the scale is being set MODE --> HI/LO SAMPLE and calibrated. MODE This key is used to select the display mode. ( kg -> Ib -> PCS -> %) > can be used to move the position of cursor to right when the scale is being set and calibrated. HI/LO SAMPLE This key is used to preset the high-limit and low-limit of the target value. SET SET Press this key to confirm the high/low limit entered. (**backlight can be turned-on with this key 3. LCD Indications during period.) operation 1) ZERO : The scale is ZERO mode when an arrow appears on the upper left-hand part of the

5 LCD DISPLAY. 2) TARE: The scale is in TARE mode when an arrow appears on the lower left-hand part of the LCD DISPLAY. 3) LO-BAT : The battery symbol indicates that the battery needs recharging. 4) HI, GO, LO: Display the state of Checking function. 4. Explanation of functions 1) ZERO FUNCTION: This function returns the display to the true zero if it indicates otherwise. 2) AUTO POWER-OFF (power saving function) : This function will automatically shut off the scale when not in use for extended periods of time. (matching Fun-4, you can set the scale off after 4 minutes when not in use.) 3) CHECKING FUNCTION Weight checking a. High, Low limit value setting by keypad entry: STEP1. Press MODE key to select the desired weight unit (kg or Ib). STEP2. Press the HI/LO/SAMPLE key, and enter the High-limit value (MODE: -->, TARE:+, ON/ZERO:-). STEP3. Press the SET key to confirm the STEP4. Press the HI/LO/SAMPLE key twice, and enter the low-limit value (MODE: -->, TARE:+, ON/ZERO :-). STEP5. Press the SET key to confirm the STEP6. Start to weigh (beep or not, refer to F30). b. High, Low limit value setting be actual load: STEP1. Press MODE key to select the desired weight unit ( kg or Ib) STEP2. Loading the commodity of High limit value, then press the HI/LO SAMPLE key once. STEP3. Press the SET key to confirm the STEP4. Loading the commodity of Low-limit value, then press the HI/LO/SAMPLE key twice. STEP5. Press the SET key to confirm the

6 STEP6. Start to weigh (beep or not, refer to F30). Piece checking a. High, Low limit value setting by keypad entry: STEP1. Press the MODE key to select the PCS unit. STEP2. Press the HI/LO/SAMPLE key, and enter the high-limit value ( MODE: -->, TARE: +, ON/ZERO : -). STEP3. Press the SET key to confirm the STEP4. Press the HI/LO/SAMPLE key twice, and enter the low-limit value ( MODE: -- >, TARE:+, ON/ZERO: -). STEP5. Press the SET key to confirm the STEP6. Start to count (beep or not, refer to F30). b. High, Low limit value setting by actual load: STEP1. Press MODE key to select the PCS unit. STEP2. Loading the commodity of High-limit value, then press the HI/LO/SAMPLE key once. STEP3. Press the SET key to confirm the STEP4. Loading the commodity of Low-limit value, then press the HI/LO/SAMPLE key twice. STEP5. Press the SET key to confirm the STEP6. Start to weigh (beep or not, refer to F30). Percent checking a. High, Low limit value setting by keypad entry: STEP1. Press the MODE key to select the % unit. STEP2. The high-limit and low-limit values setting are the same as described in WEIGHT CHECKING and/or PIECE CHECKING. b. High, Low limit value setting by actual load: STEP1. Press the MODE key to select the % nit. STEP2. The high-limit values setting are the same as described in WEIGHT CHECKING and/or PIECE CHECKING.

7 **During routine operation period, Checking function can act only if the weight exceed 40 divisions. 4)`SAMPLING FUNCTION a.`piece sampling: STEP1. Load sample of a combined weight over 1e ( one division) of each 5-pieces on the weighing Platform. (5pcs> 1e) STEP2. Press the HI/LO/SAMPLE 3 times, the following message is displayed 5 pcs and it can be changed with the +, - keys (5 pcs <--> 10 pcs<--> 20 pcs < --> 50 pcs< -- > 100 pcs < -- > 500 PCS< -- > 1000 PCS). STEP3. Press the SET key to confirm the desired choice. After this action done, the chosen pieces will appear on the display again. STEP4. Remove the sample from the weighing platform, the scale is zeroed and ready for piece counting. b. Percent sampling: STEP1. Load sample of a combined weight over 1/20 of full capacity on the weighing Platform. STEP2. Press the HI/LO/SAMPLE 4 times, the following message is displayed 100 %. STEP3. Press the SET key to confirm the specified percentage. After this action done, the 100% indication will reappear on the display. STEP4. Remove the sample from the weighing platform, the scale is zeroed and ready for percentage weighing. **The resolution of sampling should not exceed the internal resolution of the scale (1e=4 or 5 internal resolution). 5) PRINT OUT (Optional) a. Printer: (Centronics-compatible, 8 bits, TTL-level.) STEP1. Be sure that the printer is connected properly. STEP2. There are two modes to be selected (Auto & Key print, refer to F12). During the routine operation, press SET key for lasting about 2 seconds, then it will be transferred to internal-function

8 Change the function number with keypad (MODE: -- >, TARE:+, ON/ZERO : - ) and press SET key for confirmation. F12: 00 key (Exceed 2% of full capacity, press ZERO key, result of weighing is printed out.) 01 Auto ( Automatic print out, after the load is stabilized and over 40 divisions. ) Press MODE key, a print out of the sum of weighings up to the last one is printed out. b. Computer (RS-232C): EIA RE-232C, half duplex,asynchronous transmission Baud rate: 300, 600, 1200, 2400, 4800, 9600, Data bit: 7, 8 bits Parity bit: Even, None Start bit: 1 bit Stop bit : 1 bit Data type: ASCII code connected properly. STEP2. Several parameters have to be set in advance. ( for RS-232C protocol, transmission mode, data format) F10: E.7 (even Parity, 7 Data bit) n.8 (no Parity, 8 Data bit) F11: 00 KEY (Exceed 2 % of full capacity, ZERO key is enabled to start printout.) 01 AUTO (exceed 40 divisions, transmitting data automatically while the scale is stabilized.) 02 SM (continuously transmission) F20: 00 Format 0 (standard) F20: 01 Format 1 STEP1. Be sure that the computer (RS-232C) is

9 F20: 02 Format 2 Head: OL Over load US Unstable ST Stable Pol. : Plus - Minus Unit: kg, Ib, pc, % Comparator status : H Above high-limit of target value G Within the acceptable range of target value L Below low-limit of target value Checking function not in-use. 6) BACKLIGHT : Press the SET key to start the backlight during operation period. FUNCTION LIST **During the routine operation, press SET key for lasting about 2 seconds, then it will be transferred to internal-function Change the function number with keypads ( MODE:, TARE:+, ON/ZERO: - ) and press SET key for confirmation. F 10: RS-232C protocol E.7 n.8 F 11: RS-232C transmission mode 00 KEY ( ZERO ) 01 AUTO 02 SM F 12: Printer transmission mode 00 KEY ( ZERO ) 01 AUTO F 20: RS-232C data format 00 Format 0 (standard) 01 Format 1 02 Format 2 F21 Printer data format 00 Format 0 (standard), See Figure 1.1,

10 1.2 S/N kg Varies according to the present unit. =============== / Sum total of weighings Figure 1.1 S/N Ib ================== G With comparator status L H / Sum total of weighings 02 Beep either over high-limit or under low-limit 03 Beep while above high-limit of target value 04 Beep while under low-limit of target value **Default value of functions** F10: E.7 F11: 00 F12: 00 F20: 00 F21: 00 F30: 00 Figure 1.2 F30: Beep mode 00 No beep 01 Beep if within the acceptable range of target value

4. TECHNICAL FUNCTIONS (For technicians) 1) Specification: Fun-1 : Full Digital Calibration ( Min. display resolution from 1/100 ~ 1/6000, Max. Capacity, Min.

) Fun-2 : Display / Segment check Fun-3 : Off-set value displayed ( 2000 4000 counts) and Keyboard test.

11 4. TECHNICAL FUNCTIONS (For technicians) 1) Specification: Fun-1 : Full Digital Calibration ( Min. display resolution from 1/100 ~ 1/6000, Max. Capacity, Min. Division, Decimal point, Span calibration weight can be set with keypads under any reasonable value.) Fun-2 : Display / Segment check Fun-3 : Off-set value displayed ( counts) and Keyboard test. Fun-4: Auto shut-off function (0-oFF, 4-oFF) Fun-5: RS-232C baud rate setting (300, 600, 1200, 2400, 4800, 9600, 19200) 5. Press SET key to confirm the choice. 6. To exit, press HI/LO/SAMPLE key. Fun-1: Dealer calibration By executing this function, it will allow you to calibrate the scale if it is first installed or not within the acceptable range required to calibrate in auto-calibration (for end user). 2) Procedure: 1. Press MODE key and switch on the scale simultaneously, the display will show Fun-1 2. Press MODE key continuously, the display will show Fun-2, Fun-3, Fun-4, Fun-5,.., Fun-1,..sequentially. 3. While the desired function has been chosen, press SET Key to get into next step. 4. Press MODE key to change the function s value.

12 Remarks: Refer to Note 1 and Note 2 on next page.

13 5. CARE AND MAINTENANCE Precautions: 1. Do not attempt to disassemble the scale to clean it. 2. Do not submerge the scale in water, neither do pour or spray water on it directly. 3. Never use acetone or other volatile solvents such as thinner, alcohol, etc. to clean your scale. 4. When the platform is removed from cleaning, etc., be sure not to drop items such as pins, paper clips, etc. into the hole of subplatform. They may cause damages. 5. Be sure to screw the column of the platform into or out of the whole chassis lightly if you have to put it together or take it apart. Daily care: *Clean the scale with a soft damp cloth and /or a mild detergent.

SAC / SHC / SHC-CH SERIES

This document hosted by: www.oldwillknottscales.com SAC / SHC / SHC-CH SERIES HIGH PRECISION COUNTING SCALE OPERATION MANUAL PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE SCALE July