NDB-C0706A Dual Mode Bluetooth Module

Transcription

1 NDB-C0706A Dual Mode Bluetooth Module 1 Device Overview 1.1 Description This module is designed with Cypress CYW20706 (previously Broadcom BCM20706) dual mode Bluetooth 5.0 SoC. CYW20706 features 96 MHz Cortex M3 core, excellent receiver sensitivity down to -96 dbm (BLE GFSK), integrated PA to support Class 1 Tx power up to 12 dbm. These two RF parameters contribute the best in class link budget to enable long range Bluetooth communication up to 100 meters. As a dual mode Bluetooth module, it can realize BLE over GATT and SPP connections simultaneously, which provide the best interoperability to various ios and Android devices. It supports both BR (2 Mbps) and EDR (3 Mbps) when running SPP. This helps to enable applications which require higher throughput than BLE can provide. Its raw data throughput running SPP can reach up to 1 Mbps. This module also supports Bluetooth audio profiles including but not limited to A2DP, HFP, and AVRCP. An external audio codec can be connected via PCM interface to drive a speaker and a microphone. This module can also support IAP2 and HomeKit for MFi licensed developers. The module comes with a set of AT commands via UART interface for setting up a bidirectional Bluetooth data link easily between an application MCU and mobile phones. 1.2 Key Features SPP Profile: SPP as a Classic Bluetooth profile has better interoperability (IoP) than BLE over GATT, particularly support mobile phones with lower Android version (v4.3 and below). BLE over GATT: BLE peripherals have no need for MFi certification to connect ios devices Transparent Data Transmission: Simple to realize data communication and control between devices and mobile phones. Beacon: Support both ibeacon and EddyStone beacon. Master and Slave Concurrent Mode: Connect both master and slave devices concurrently to support various multi-role applications. Multi-connection: Connect multiple mobile phones and APPs for multi-user applications Over-The-Air (OTA) Upgrade: Upgrade the application code or the module s firmware through BT/BLE air link. 1.3 Applications Bluetooth to serial port communication Industrial remote monitor and control Bluetooth printer and card reader Barcode scanner Security alarm system Indoor positioning and alarm Home or building automation Factory automation Chengdu Necdaz Technology Co., Ltd. Page 1 of 10

2 Home appliance Smart lighting 1.4 Block Diagram System Block Diagram Block Diagram of Application Environment Chengdu Necdaz Technology Co., Ltd. Page 2 of 10

3 1.4.3 Block Diagram of Audio Application 1.5 Part Number Conventions The part numbers are of the form of NDB-C0706A where the fields are defined as follows. Figure 1. Part Number Conventions Chengdu Necdaz Technology Co., Ltd. Page 3 of 10

4 Table of Contents 1 DEVICE OVERVIEW DESCRIPTION KEY FEATURES APPLICATIONS BLOCK DIAGRAM System Block Diagram Block Diagram of Application Environment Block Diagram of Audio Application PART NUMBER CONVENTIONS REVISION HISTORY TERMINAL CONFIGURATION AND FUNCTIONS HARDWARE INTERFACE PARAMETERS PIN DIAGRAM PIN ATTRIBUTES MODULE COMMUNICATION PROTOCOL HARDWARE PARAMETERS PHYSICAL PARAMETERS ELECTRICAL PARAMETERS CURRENT PARAMETERS SPP under Dual Mode BLE under Dual Mode Single BLE Mode MECHANICAL AND PACKAGING INFORMATION MECHANICAL DRAWING RECOMMENDED PCB LAYOUT FOR PACKAGE PROCESS PARAMETERS RECOMMENDED FURNACE TEMPERATURE CURVE Revision History NOTE: Pages number may be different from the former ones. Version No.: Page Changed Xx Xx Added Xx Xx Chengdu Necdaz Technology Co., Ltd. Page 4 of 10

5 3 Terminal Configuration and Functions 3.1 Hardware Interface Parameters Power Supply Host Interface Interface Signal +3.3 V ± 0.3 V UART (CMOS, TTL level) RX, TX, CTS, RTS 3.2 Pin Diagram Figure 2. Pin Diagram of NDB-C2706A Chengdu Necdaz Technology Co., Ltd. Page 5 of 10

6 3.3 Pin Attributes Table 1. Pin Attributes of NDB-C0706A Pin Name Chip Pin Description 1 GND Ground Ground 2 3P3VD Power Power Supply: DC 1.8 V~3.6 V 3 NC NC / 4 NC NC / 5 3P3VD Power Internal connection with BP2 6 UART_RTS_N O Software download pin 7 P27 I GPIO (Command/ Data select pin) 8 NC NC / 9 P24 O GPIO (BT connection status) 10 P36 I GPIO (wake-up pin) 11 P3 I/O GPIO 12 P12 I/O GPIO 13 P3 I/O 1)GPIO 2)PUART0_CTS (reserved) 14 P27 I GPIO 15 P30 I/O 1)GPIO 2)PUART_RTS (reserved) 16 UART_TXD O Software download PIN I2S_WS/CLK/PCM_SYNC 17 UART-RXD I Software download PIN I2S_WS/CLK/PCM_SYNC 18 UART_CTS_N I Software download pin 19 RST_L I External reset signal input, active low, internal self-pullup 20 UART_RXD I RXD (default) 21 UART_TXD O TXD (default) 22 P15 I/O GPIO 23 SPI2_MISO I/O SPI_MISO 24 SPI2_MOSI I/O SPI_MOSI 25 SPI2_CLK I/O SPI_CLK 26 P31 I GPIO (LPO32.768Hz CLK input) 27 P25 I/O GPIO 28 P26 O GPIO(LED state output) 29 GND Ground Ground 30 BT_RF O Antenna Chengdu Necdaz Technology Co., Ltd. Page 6 of 10

7 4 Module Communication Protocol Module Name NDB-C0706A Interface RS232 Baud Rate (Default: ) Stop Bit 1 Data Bit 8 bit Validation Bit None 5 Hardware Parameters 5.1 Physical Parameters Operating Frequency Band 2.4 GHz GHz unlicensed ISM band Bluetooth Specification 5.0 Output Power Class Class 2 RX Sensitivity 88 dbm Operating Voltage 3.3 V ± 0.3 V Main Digital Interface UART Other Interfaces PIO Control Dimension SPI GPIO 15 mm (L) x 12 mm (W) x 1.7 mm (H) 5.2 Electrical Parameters Rating Min. Max. Storage Temperature Operating Temperature Supply Voltage: VDD -0.3 V 3.6 V Other Terminal Voltages VSS - 0.3V VDD V 5.3 Current Parameters SPP under Dual Mode Operation Mode AVG Current Note Shutdown 8 µa MCU idle + no discoverable 1.1 ma MCU idle + discoverable 1.2 ma 500 ms Broadcast interval MCU active + discoverable 1.9 ma 500 ms Broadcast interval Connected+ MCU idle (no data) 1.85 ma Connected+ MCU active (no data) 1.9 ma Connected + transfer data 8.23 ma Data transmit rate: 2.6 KB/s Chengdu Necdaz Technology Co., Ltd. Page 7 of 10

8 5.3.2 BLE under Dual Mode Operation Mode AVG Current Unit Shutdown 8 µa MCU idle + no adv 1.1 ma MCU idle + adv 1.2 ma 500 ms Broadcast interval MCU active + adv 1.9 ma 500 ms Broadcast interval Connected+ MCU idle (no data) 1.85 ma Connected+ MCU active (no data) 1.9 ma Connected + transfer data 3.15 ma Data transmit rate: 2.6 KB/s Single BLE Mode Operation Mode AVG Current Unit Shutdown 8 µa MCU idle + no adv 60 µa MCU idle + adv 120 µa 500 ms Broadcast interval MCU active + adv 1.1 ma 500 ms Broadcast interval Connected+ MCU idle (no data) 220 µa Connected+ MCU active (no data) 320 µa Connected + transfer data 3.15 ma Data transmit rate: 2.6 KB/s 6 Mechanical and Packaging Information 6.1 Mechanical Drawing Figure 3. Mechanical Drawing of NDB-C0706A Chengdu Necdaz Technology Co., Ltd. Page 8 of 10

9 6.2 Recommended PCB Layout for Package Figure 4. Recommended PCB Layout (mm) Note: 1. During layout, the antenna area should be kept clear, and the line and copper shall be prohibited. 2. The filter capacitance should be as close to the module as possible. 3. Strong interference line at the bottom of the module should be forbidden. Chengdu Necdaz Technology Co., Ltd. Page 9 of 10

10 7 Process Parameters 7.1 Recommended Furnace Temperature Curve Referred to IPC/JEDEC standard. Peak temperature: <250 C Number of times: 2 Chengdu Necdaz Technology Co., Ltd. Add.: B3-22, Building No. 1, Incubation Park, High-Tech Zone, Chengdu, Sichuan, China, Web.: necdaz@necdaz.com Tel.: Chengdu Necdaz Technology Co., Ltd. Page 10 of 10