MYD-JA5D2X Development Board

Size: px

Start display at page:

Download "MYD-JA5D2X Development Board"

Gordon Hancock
5 years ago
Views:

MYD-JA5D2X Development Board MYC-JA5D2X CPU Module as Controller Board 500MHz Atmel SAMA5D26/27 ARM Cortex-A5 Processor 256MB DDR3 SDRAM, 256MB Nand Flash, 4MB Data FLASH, 64KB EEPROM Serial ports,

1 Figure 1-1 MYD-JA5D2X Development Board Description The MYD-JA5D2X Development Board is a complete evaluation platform for Atmel s latest SAMA5D2 (26/27) ARM Cortex-A5 processor which supports

1 MYD-JA5D2X Development Board MYC-JA5D2X CPU Module as Controller Board 500MHz Atmel SAMA5D26/27 ARM Cortex-A5 Processor 256MB DDR3 SDRAM, 256MB Nand Flash, 4MB Data FLASH, 64KB EEPROM Serial ports, USB, Ethernet, RS485, TF, Audio, LCD One CAN Interface (Only for SAMA5D27) Ready-to-Run Linux 4.1 Figure 1-1 MYD-JA5D2X Development Board Description The MYD-JA5D2X Development Board is a complete evaluation platform for Atmel s latest SAMA5D2 (26/27) ARM Cortex-A5 processor which supports multiple memories, including latest-generation technologies such as DDR3, LPDDR3, and QSPI Flash and is integrated with rich peripherals including the LCD & Touch controller, Camera interface, EMAC, USB HSIC and Safety IP, capable of running at up to 500MHz. The MYD-JA5D2X development board is consist of a CPU module MYC-JA5D2X and a base board MYB-JA5D2X connected via one 200-Pin SODIMM interface. It is a complete design reference for embedded developing on the SAMA5D2X processor and designs based on MYC-JA5D2X CPU Module. The MYC-JA5D2X CPU Module has integrated the core components including the SAMA5D2 processor, 256MB DDR3, 256MB Nand Flash, 4MB Data FLASH, 64KB EEPROM and 100M Ethernet PHY on board. It has been designed to support up to 512MB DDR3 and 1GB Nand Flash (or 16GB emmc Flash) on customer demand. They can be embedded into your next design directly to speed up your time to market. 1 / 10

Figure 1-2 MYC-JA5D2X CPU Module The MYD-JA5D2X development board is built around the MYC-JA5D2X CPU Module and takes out full features of the Atmel SAMA5D2

SAMA5D27), Ethernet port, RS485, TF card slot, Audio in/out, LCD, etc.

2 Figure 1-2 MYC-JA5D2X CPU Module The MYD-JA5D2X development board is built around the MYC-JA5D2X CPU Module and takes out full features of the Atmel SAMA5D2 processor to extend a rich set of peripherals and interfaces through headers and connectors including serial ports, USB Host and Device ports, CAN port (only for SAMA5D27), Ethernet port, RS485, TF card slot, Audio in/out, LCD, etc. Figure 1-3 MYD-JA5D2X Development Board MYIR deliveries the MYD-JA5D2X Development Board with SAMA5D27 processor by default. The board comes along with Linux 4.1 software packages, necessary cable accessories as well as detailed documents to enable quick start 2 / 10

3 when getting the goods out of box. It can support -40 to +85 Celsius extended temperature operation for industrial embedded applications. It is an excellent EVM (Evaluation Module) and a good reference design for extensively evaluation, fast prototyping and creating applications that require high efficient computing, display, audio, mass storage, networking, connectivity and more. Hardware Specification The Atmel SMART SAMA5D2 series is a high-performance, ultra-low power Cortex-A5 processor based MPU. It supports multiple memories, including latest generation such as DDR3, LPDDR3, and QSPI Flash. It is particularly well-suited for small control panel/hmi applications and secure IoT gateway/connectivity applications. The AMA5D2 is also ideal for barcode scanners and printers as well as mid-range POS terminals that require PCI. The improved low power features and small package deliver an excellent solution for wearables and other batteryoperated applications. Figure 1-4 SAMA5D2 Series Devices The MYD-JA5D27 development board includes one MYC-JA5D27 CPU module mounted on the base board. It exposes many of the Atmel SAMA5D27 features to the user in support of developing specific solutions. The main features are characterized as below: Mechanical Parameters Power supply: 5V/2A (Base Board), 3.3V/0.5A (CPU Module) Working temperature: -40~85 Celsius (industrial grade) Dimensions: 110mm*135mm (Base Board), 67.6mm*45mm (CPU Module) PCB layer: 4-layer (Base Board), 8-layer (CPU Module) 3 / 10

The MYD-JA5D27 Controller Board (MYC-JA5D27 CPU Module) Figure 1-5 MYC-JA5D2X CPU Module Top-view Figure 1-6 MYC-JA5D2X CPU Module Bottom-view Processor Atmel SAMA5D27 Processor (SAMA5D26 is

- 10/100 MAC with IEEE1588 - Two HS High Speed USB ports (configurable as two hosts or one host and one device port) - One High Speed Inter-Chip Interface (HSIC) port - One 12-bit image sensor

4 The MYD-JA5D27 Controller Board (MYC-JA5D27 CPU Module) Figure 1-5 MYC-JA5D2X CPU Module Top-view Figure 1-6 MYC-JA5D2X CPU Module Bottom-view Processor Atmel SAMA5D27 Processor (SAMA5D26 is compatible) - ARM Cortex-A5 core running at 500MHz (785DMIPS) KB of L2 cache for system performance. - Floating point unit (FPU) for high-precision computing and accelerated data processing. - 10/100 MAC with IEEE Two HS High Speed USB ports (configurable as two hosts or one host and one device port) - One High Speed Inter-Chip Interface (HSIC) port - One 12-bit image sensor controller with Raw Bayer support - Graphic LCD controller with overlays for image composition - Advanced security features to prevent counterfeiting, secure external communication, and authenticate the system - Market-leading low power consumption o Less than 150mW in active mode at 500MHz with all peripherals activated o Less than 0.5mW in low power mode with SRAM and registers retention o Dual CAN-FD controller Feature SAMA5D26 SAMA5D27 USB 2 (2 Hosts or 1 Host/1 Device) 3 (2 Hosts/1 HSIC or 1 Host/1 Device/1 HSIC) CAN 0 2 AESB - Yes Table 1-1 Main Differences between SAMA5D26 and SAMA5D27 Devices Memory 256MB DDR3 (supports up to 512MB DDR3 SDRAM) 256MB Nand Flash (supports up to 512MB Nand Flash, reserved optional emmc design) 4MB Data FLASH 64KB EEPROM Peripherals and Signals Routed to Pins On-board Ethernet PHY One power indicator (Red LED) One user LED (Blue) SO-DIMM 200-pin connector brings out below peripheral signals: 4 / 10

Signals Ethernet GPIO USB Serial Ports I2C CAN SPI QSPI ADC PWM SDIO LCD SSC Camera SMC Description 1*10/100M Ethernet Up to 97*GPIO 3*USB (1 x Host, 1 x Device, 1 x HSIC, HSIC is only for SAMA5D27)

parallel external memory interface Table 1-2 Extension signals on SO-DIMM 200-pin connector Note: Some signals are reused and listed with the maximum numbers.

5 Signals Ethernet GPIO USB Serial Ports I2C CAN SPI QSPI ADC PWM SDIO LCD SSC Camera SMC Description 1*10/100M Ethernet Up to 97*GPIO 3*USB (1 x Host, 1 x Device, 1 x HSIC, HSIC is only for SAMA5D27) Up to 10*Serial ports Up to 7*I2C Up to 2*CAN (only for SAMA5D27) Up to 7*SPI Up to 2*QSPI 12*ADC 4*PWM 1*SDIO 1*24-bit LCD Signal Up to 2*SSC, compatible with I2S 1*12-bit Camera Interface Supports parallel external memory interface Table 1-2 Extension signals on SO-DIMM 200-pin connector Note: Some signals are reused and listed with the maximum numbers. For detailed configuration, please refer to the document of Pin-out Description. The MYD-JA5D27 Base Board (MYB-JA5D2X) Figure 1-7 MYD-JA5D2X Base Board (MYB-JA5D2X) 5 / 10

6 Serial ports - 2 x RS232-1 x RS485 USB - 1 x USB2.0 Host ports - 1 x Mini USB2.0 Device port - 1 x USB HSIC (only for SAMA5D27, via Extension Headers) 1 x 10/100Mbps Ethernet interfaces 1 x CAN interface (only for SAMA5D27) 1 x TF card slot 1 x 18-bit LCD interface 1 x 4-wire resistive touch screen interface 1 x 8-bit Camera interface (J23, 2.0mm pitch 20-pin connectors) 1 x Mic in port 1 x Line in port 1 x Stereo Audio output port (Headphone) 1 x JTAG interface (2.54mm pitch, 20-pin connector, J16) 1 x battery backed RTC socket 4 x Buttons (Boot SEL, Reset, Wake up, User) 2 x 2.0mm pitch 20-pin Extension Headers (J7 & J21) - 2 x SPI, 2 x UART, 1 x TWI, 1 x QSPI (some signals are reused) 1 x 2.0mm pitch 20-pin Secure IO Header (J8) 1 x FMC interface (DNP by default, on the bottom of the board) 3 x LEDs (1 x Power, 2 x User) 6 / 10

7 Function Block Diagram Figure 1-8 MYC-JA5D2X Function Block Diagram Figure 1-9 MYD-JA5D2X Function Block Diagram 7 / 10

8 Dimensions: Figure 1-10 Dimensions of MYC-JA5D2X CPU Module Figure 1-11 Dimensions of MYD-JA5D2X Development Board Base Board 8 / 10

9 Software Features The MYD-JA5D2X development board is preloaded with Linux 4.1. Many of the drivers are provided in source code as shown in below table. Item Feature Description Source Code Provided Bootloader AT91bootstrap First level boot program Yes u-boot second level boot program Yes Kernel version Linux 4.1 Yes Mini USB USB driver, can switch between Host and Device Yes Ethernet 10M/100Mbps Ethernet driver Yes MMC/SD MMC/SD card driver Yes NandFlash Nand Flash driver Yes CAN Industrial CAN Bus driver Yes RS485/RS232 RS485/RS232 serial port driver Yes Driver Audio In/Out I2S interface, wm8904 driver Yes LCD Controller MYIR s 4.3- and 7-inch LCD Module driver Yes RTC RTC driver Yes Touch Panel Resistive or capacitive touch panel driver Yes Button Button driver Yes LED LED driver Yes ADC ADC driver Yes PWM PWM driver Yes FileSystem Compilation toolchain Yocto filesystem including QT5.5 base running environment(qt) Binary Buildroot based Yes Linaro GCC 4.9 hf Binary Table 1-3 Software Features List 9 / 10

10 Order Information Product Item MYD-JA5D27 Development Board (Part No.: MYD-JA5D27-256N256D-I) Packing List One MYD-JA5D27 Development Board One cross network cable One USB type A to Mini type B cable One Serial cable One 5V/2A power adapter One product disk Add-on Options MYC-JA5D27 CPU Module (Part No.: MYC-JA5D27-256N256D-I) MY-LCD43TP LCD Module with resistive touch screen (Part No.: MY-TFT043CV2) MY-LCD70TP LCD Module with resistive touch screen (Part No.: MY-TFT070RV2) MY-LCD70TP-C LCD Module with capacitive touch screen (Part No.: MY-TFT070CV2) MY-SODIMM200 Socket (Part No.: MY-SODIMM200) Remark: 1. One MYD-JA5D2X Development Board includes one CPU module MYC-JA5D2X mounted on the base board. If you need more CPU module, you can order extra ones. 2. Our products are delivered in industrial grade ranging from -40 to 85 Celsius. 3. We accept custom design based on the MYD-JA5D2X, whether reducing, adding or modifying the existing hardware according to customer s requirement. MYIR Tech Limited Room 1306, Wensheng Center, Wenjin Plaza, North Wenjin Road, Luohu District, Shenzhen, China sales@myirtech.com Phone: Fax: Website: 10 / 10

MYD-SAMA5D3X Development Board

MYD-SAMA5D3X Development Board MYC-SAMA5D3X CPU Module as Controller Board DDR2 SO-DIMM 200-pin Signals Consistent with Atmel's Official Board 536MHz Atmel SAMA5D3 Series ARM Cortex-A5 Processors 512MB