GX620 (MS-1651)Disassemble SOP

Transcription

1 GX620 (MS-1651)Disassemble SOP 1 Battery Pack 2 BOTTOM DOOR ASSY 3 THERMAL-KIT And CPU Module 4 RAM WLAN And TUNER Module 5 HDD Module ASSY 6 ODD Module ASSY 7 HINGE COVER ASSY 8 UP CASE ASSY 9 LOWER CASE ASSY 10 LCD MODULE ASSY

2 1 Battery Pack 1-1:Push the battery Unlock button as below; 1-2:Push the battery Release button as below, then slide the battery pack out of the slot; 1 Battery Pack S9N SB3 1

3 2 BOTTOM DOOR ASSY 2-1:Remove 2pcs M2.5*5mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm GX620&MS-1651 Disassemble SOP 2-2:Remove Bottom Door Assy as below;

4 2-3:Remove SIM Card Door as below; 1 Screw E H SIM CARD DOOR E2P Y BOTTOM DOOR ASSY J411-Y31 1

5 3 THERMAL-KIT And CPU Module 3-1:Remove 7pcs SPING Screws, Then Disconnect CPU Fan sink Cable; Note:Screw driver torque is 2.0~2.5kgf.cm :Remove CPU Fan sink; 1 CPU FANSINK E F05 1

6 3-3: Open CPU slot as below; 3-4:Remove CPU Module; 1 CPU Module A I06 1

7 3-5:Remove 2pcs M2.5*5mm Screws; Note:Screw driver torque is 2.5~3.0kgf.cm GX620&MS-1651 Disassemble SOP 3-6:Remove VGA Card Module; 1 VGA CARD Module 602-V114-06S 1 2 Screw E H29 2

8 4 RAM WLAN And TUNER Module 4-1:Push RAM Slot Fastener as below; 4-2:Remove RAM Module; 1 RAM Module S7C-S T10 2

9 4-3:Remove WLAN Card Antenna, Then remove 1pcs M2*3mm Screw; Note:Screw driver torque is 1.8~2.2kgf.cm 4-4:Remove WLAN Card Module; 1 WLAN CARD Module S I Screw E H29 1

10 4-5:Remove Tuner Antenna, Then remove 1pcs M2*3mm Screw; Note:Screw driver torque is 1.8~2.2kgf.cm 4-6:Remove Tuner Module; 1 TUNER Module S K Screw E H29 1

11 5 HDD Module ASSY 5-1:Remove 2pcs M2.5*5mm Screws Then remove HDD Door Assy as below; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E H HDD DOOR ASSY K411-Y31 1

12 5-2:Remove HDD Module as below; 1 Screw E H29 1

13 5-3:Remove 2pcs M3*3.5mm Screws Then remove HDD Bracket as below; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E H HDD Bracket Y HDD MODULE ASSY S F06 1

14 6 ODD Module ASSY 6-1:Remove 1pcs M2.5*5mm Screw Then remove ODD Module Assy as below; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E H29 1

15 6-2:Remove ODD Bezel as below; 1 ODD Bezel E2P-651F211-Y31 1

16 6-3:Remove 2pcs M2*3mm Screws Then remove ODD Bracket as below; Note:Screw driver torque is 1.5~1.8kgf.cm 1 Screw E H ODD Bracket E2M Y28 1

17 7 HINGE COVER ASSY 7-1:Push Fastener as below; GX620&MS-1651 Disassemble SOP

18 7-2:Remove Hinge Cover as below; GX620&MS-1651 Disassemble SOP 1 HINGE COVER E111-Y31 1

19 7-3:Remove Hinge Cover Cable as below; 1 POWER BOARD B-C10 1

20 7-4:Remove Cap Sensor Board as below; 1 Cap Sensor Board D-C10 1

21 7-5:Remove Cap Sensor Board as below; 1 Cap Sensor Board D-C Cap Sensor Board Cable K1C J36 1

22 8 UPCASE ASSY 8-1:Remove 5pcs M2*3mm Screws, Then remove Keyboard as below; Note:Screw driver torque is 1.5~2.0kgf.cm 1 Screw E H Keyboard S1N-3UTC131-C54 1

23 8-2:Remove 2pcs M2*3mm Screws, Then remove Power Board as below; Note:Screw driver torque is 1.5~2.0kgf.cm 1 Screw E H Power Board B-C10 1

24 8-3:Remove 13pcs M2.5*5mm Screws, Then remove 2pcs M2.5*7mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E H Screw E H29 2

25 8-4:Remove PCI-E Card And XD Card as below; 1 PCI-E Card E2P Y XD Card E2P Y31 1

26 8-5:Disconnect Speaker Cable and Microphone Cable as below; 1 Speaker Cable S33-A F Microphone Cable S F33 1

27 8-6:Remove FFC Cable(TO Audio Board) and FFC Cable(TO M/B) as below; 1 FFC Cable(TO Audio Board) K1C J FFC Cable(TO M/B) K1C J36 1

28 8-7:Remove 2pcs M2*3mm Screws, Then remove FFC Cable(TO M/B)&(TO Button) as below; Note:Screw driver torque is 1.5~2.0kgf.cm 8-8:Remove Touchpad Bracket; 1 Screw E H FFC Cable(TO Button) K1C J Touchpad Bracket E2M Y28 1

29 8-9:Remove 1pcs M2*3mm Screw, Then remove Touchpad Button Board; Note:Screw driver torque is 1.0~1.5kgf.cm 1 Screw E H Touchpad Button Board C-C10 1

30 8-10:Remove FFC Cable (TO Button) as below; 1 FFC Cable(TO Button) K1C J Touchpad Module S SD2 1

31 9 LOWER CASE ASSY 9-1:Remove 1pcs M2.5*5mm Screw, Then remove FFC Cable (TO Audio Board) as below; Note:Screw driver torque is 2.3±0.2kgf.cm 9-2:Remove FFC Cable (TO Power Board) as below; 1 Screw E H FFC Cable(To Audio Board) K1C J FFC Cable(To Power Board) K1C J36 1

32 9-3:Remove RJ11 Cable and Bluetooth Cable as below; 9-4:Remove M/B; 1 RJ11 CABLE K H BLUETOOTH CABLE K H M/B B10 1

33 9-5:Remove 1pcs M2*3mm Screw, Then remove Bluetooth Antenna; Note:Screw driver torque is 1.0~1.5kgf.cm 1 Screw E H BLUETOOTH ANTENNA S V BLUETOOTH MODULE D-070 1

34 9-6:Remove 2pcs M2*3mm Screws, Then remove Audio Board; Note:Screw driver torque is 1.0~1.5kgf.cm 1 Screw E H AUDIO BOARD A-C LOWER CASE ASSY D411-Y31 1

35 9-7:Remove Bluetooth Antenna RJ11 Cable and TV IO Jack; 1 BLUETOOTH ANTENNA S V RJ11 CABLE K H TV IO JACK K H39 1

36 10 LCD MODULE ASSY 10-1:Disconnect Camera Cable as below; GX620&MS-1651 Disassemble SOP 1 Camera Cable K H39 1

37 10-2:Remove 2pcs M2.5*5mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm 10-3:Use Plastic Stick Push Hinge Cap as below; 1 Screw E H Hinge Cap_L E2P Y Hinge Cap_R E2P Y31 1

38 10-4:Draw Out Camera Cable Wireless Antenna and 3G Antenna as below; 1 3G Antenna S V Wireless Antenna_L S V Wireless Antenna_R S V03 1

39 10-5:Disconnect Coaxia Cable as below; 1 Coaxia Cable K H39 1

40 10-6:Remove 2pcs M2.5*7mm Screws; Note:Screw driver torque is 3.5±0.2kgf.cm 1 Screw E H29 2

41 10-7:Remove 8pcs LCD Rubbers Then remove 8pcs M2.5*5mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm 1 LCD Rubber E2Y Y Screw E H29 8

42 10-8:Remove LCD Bezel as below; 1 LCD BEZEL B411-Y31 1

43 10-9:Remove 6pcs M2.5*5mm Screws, Then remove Left And Right Hinge; Note:Screw driver torque is 2.0~2.5kgf.cm 1 Screw E H Hinge_Left E2M G Hinge_Right E2M G60 1

44 10-10:Remove Inverter Cable, Then remove Display Module; 1 Display Module S1J-690A004-S02 1

45 10-11:Remove Inverter Module 3G Antenna WLAN Antenna; 1 INVERTER S SG3 1 2 Wireless Antenna_R S V Wireless Antenna_L S V G Antenna S V03 1

46 10-12:Remove CMOS Camera Module as below; 1 CMOS Camera Module S1F C Camera Cable K H LCD Cover Assy A511-CG0 1

47 10-13:Remove Coaxial Cable as below; 1 Coaxial Cable K H Display Module S1J-690A004-S02 1

48 10-14:Remove 8pcs M2*3mm Screws, Then remove LCD Bracket as below; Note:Screw driver torque is 1.5~2.0kgf.cm 1 Screw E H LCD Bracket_Left E2M Y LCD Bracket_Right E2M Y28 1

49 GX620 (MS-1651)screws specification Photo Screw specification Label (M2.5*L5MM) black (M2*L3MM)white (M3*L3.5MM) white (M2.5*L7MM) black

50 GX620 (MS-1651)screws specification 1 BOTTOM DOOR ASSY total 18Pcs M2.5*5 and 2pcs M2.5*7 screws, specification: Photo Screw specification label (M2.5*L7MM) black (M2.5*L5MM) black

51 GX620 (MS-1651)screws specification 2 THERMAL-KIT total 7pcs spring Screws

52 GX620 (MS-1651)screws specification 3 TUNER, WIRELESS,MDC CARD and HDD ASSY total 8Pcs screws, specification: Photo Screw specification label (M3*L3.5MM) white (M2*L3MM)white

53 GX620 (MS-1651)screws specification 4.UPCASE ASSY total 13pcs screws, specification: Photo Screw specification Label (M2*L3MM)white (M2.5*L5MM) black

54 GX620 (MS-1651)screws specification 5.LCD Bezel total 8pcs screws, specification: Photo Screw specification label (M2.5*L5MM) black

55 GX620 (MS-1651)screws specification 6. LCD MODULE ASSY total 14cs screws specification: Photo Screw specification label (M2.5*L5MM) black (M2*L3MM)white

56 GX620 (MS-1651)screws specification 7. UPCASE and LOWER CASES total 3pcs screws, specification: Photo Screw specification label (M2*L3MM)white

57 8 NB total 1pcs screw, specification: GX620 (MS-1651)screws specification Photo Screw specification label (M2.5*L5MM) black

58 9. Bluetooth and Audio Board 3pcs screws specification: GX620 (MS-1651)screws specification Photo Screw specification label (M2*L3MM)white

59 GX620 (MS-1651)screws specification 10. Touch Pad Board total 3pcs screws specification: Photo Screw specification label (M2*L3MM)white