White Paper. Fabasoft on Microsoft Windows - Cluster Support. Fabasoft Folio 2017 R1 Update Rollup 1

Transcription

1 White Paper Fabasoft on Microsoft Windows - Cluster Support Fabasoft Folio 2017 R1 Update Rollup 1

2 Copyright Fabasoft R&D GmbH, Linz, Austria, All rights reserved. All hardware and software names used are registered trade names and/or registered trademarks of the respective manufacturers. No rights to our software or our professional services, or results of our professional services, or other protected rights can be based on the handing over and presentation of these documents. Fabasoft on Microsoft Windows - Cluster Support 2

3 Contents 1 Introduction 4 2 Software Requirements 4 3 Cluster Preparation 4 4 Cluster Installation Installing the Failover Clustering Service: Installing the Cluster 6 5 Configure Cluster Support for a Fabasoft Folio Service 9 6 Fabasoft Folio Distributed Transaction Manager 11 Fabasoft on Microsoft Windows - Cluster Support 3

4 1 Introduction This document describes how to install and configure Fabasoft Folio Backend Services to run on a failover cluster with two nodes utilizing Microsoft Windows. 2 Software Requirements System environment: All information contained in this document implicitly assumes a Microsoft Windows environment. Supported platforms: For detailed information on supported operating systems and software see the software product information on the Fabasoft distribution media. Descriptions in this document are based on the following software: Microsoft Windows Server 2016 Standard (x64) Note: If the Fabasoft product is installed on a database cluster, the database instances have to be created manually. 3 Cluster Preparation Prerequisites which are necessary to successfully install a failover cluster: at least two server nodes (which you want to cluster) two active networks o network: for network traffic and remote connection o heartbeat network suitable storage for cluster quorum and cluster disks Note: To install the needed MSI packages on the second cluster node, you can use the Fabasoft Folio Setup. During setup, do not select Fabasoft Folio Domain to perform a binary-only installation of selected Fabasoft Folio services. Fabasoft on Microsoft Windows - Cluster Support 4

5 4 Cluster Installation 4.1 Installing the Failover Clustering Service: Install the server feature Failover Cluster Management using the Add Feature Wizard. Fabasoft on Microsoft Windows - Cluster Support 5

6 After the Failover Cluster feature is installed correctly you can find the new feature in Administrative Tools in the Start menu. 4.2 Installing the Cluster To install the cluster, perform the following steps: 1. Open the Failover Cluster Management. Fabasoft on Microsoft Windows - Cluster Support 6

7 2. Create a new failover cluster click Create a Cluster. Fabasoft on Microsoft Windows - Cluster Support 7

8 The Create Cluster Wizard will start and provide a wizard that guides you through the installation of the failover cluster. 1. Specify the cluster nodes. Enter the host name of a server that you wish to cluster and click Add until at least two or more servers are selected. Click Next. 2. Specify the cluster name and the cluster IP address. Click Next. Fabasoft on Microsoft Windows - Cluster Support 8

9 3. Validate the settings and click Next. The cluster validation test will start, which verifies that the configuration that you made is sufficient for creating a failover cluster. 4. After the cluster validation test is finished you can review the result of the test and by clicking Next the cluster configuration will finish. 5 Configure Cluster Support for a Fabasoft Folio Service To configure cluster support for a Fabasoft Folio Service, perform the following steps: 1. Start the Fabasoft Folio Server Management. Fabasoft on Microsoft Windows - Cluster Support 9

10 2. Select the service you want to run on the cluster open the context menu and click All Tasks > Configure Cluster Support. 3. Enter the password for the service account. 4. Create a new virtual server if you do not have created a valid cluster group before. 5. Link the storage to the cluster service. If you want that other physical drives are also linked to the virtual server, you have to start the Failover Cluster Management and select the virtual service. Open the context menu of the Fabasoft on Microsoft Windows - Cluster Support 10

11 virtual server, click Add storage and select the disks you want to link. 6. Check if everything finished correctly. o In the Fabasoft Folio Server Management the column Cluster Resource must have the value Yes, for the service you have already clustered. o In the Failover Cluster Management the virtual server that was created in the step Configure cluster support must be displayed in the Services and Applications menu of the cluster. 6 Fabasoft Folio Distributed Transaction Manager Using a cluster, the log files for each Fabasoft Folio COO Service have to be available on an appropriate cluster resource (Fabasoft Folio Distributed Transaction Manager log files may exist only once). When changing the path to the log files of the Fabasoft Folio Distributed Transaction Manager, the existing logs files have to be moved to the new directory in order to ensure that all transactions are handled correctly. Fabasoft on Microsoft Windows - Cluster Support 11

12 By default the log files are stored in this directory: C:\ProgramFiles\Fabasoft\Components\Server\CooSrv\filesFSCDTM_COOService_x_x_x.dtm To change the location a registry key has to be defined: HKEY_LOCAL_MACHINE\SOFTWARE\Fabasoft\Fabasoft Components Server\Domain <x.y>\service <z>\datasource\default\fscdtm_txlog_path To apply changes the modified Fabasoft Folio COO Service has to be restarted. Fabasoft on Microsoft Windows - Cluster Support 12