ADVANCED DRIVER PROGRAMMING. EVERset User Manual

Size: px
Start display at page:

Download "ADVANCED DRIVER PROGRAMMING. EVERset User Manual"

Transcription

1 ADVANCED DRIVER PROGRAMMING EVERset User Manual User Manual Rev1.4 10/03/2018

2 Table of Contents 1. Introduction Computer System Requirements Definitions System Definitions... 3 Setting Definitions Getting Started/Setup Programming Software... 5 Programming Hardware... 5 LED Drivers with Compatible Programming Interface... 5 Logging into EVERset Programming Interfaces: RFID, Wired and ESI Engineering Mode Initial Screen Layout Products Screen... 9 Reading a Driver s Programmed Values Creating a Profile Setting the Dimming Curve and Values Setting Lumen Maintenance Saving Profiles Quick Programming through Engineering Mode Profile Programming through Engineering Mode Additional Profile Options Additional Menu Options Printer Setup Production Mode UserManagement Setup Adding Users Production Permissions P a g e

3 1. Introduction The EVERLINE Advanced Driver Programming system allows designers to customize LED Driver parameters with the EVERset graphical user interface and a compatible programming tool. This system will set the driver s minimum and maximum output currents, dimming curves, dimming control voltages, and to enable the dim to off command. Specific configurations can then be set and saved for production use. Programming capabilities will vary depending on the specific driver family. The programming tool will also read and display values already programmed into a driver, including the driver s part number. The programming of the LED driver is done with a programming tool connected to a computer with a USB cable. The programming tool can be used to program compatible drivers via a wired or wireless connection depending on the specific tool and driver. 2. Computer System Requirements The minimum PC requirements for the EVERset software are: >512MB RAM 1 USB Port (v2.0) Operating System: Microsoft Windows 7/8/10 FTDI drivers Hardware Requirements Handheld Programming Tool o LDPC000A Programming Tool for wired or wireless interfaces o LDPCEL0A Programming Tool for RS-232 interfaces EVERset Programming Software Printer (Optional) 2 P a g e

4 3. Definitions The programming tool is for use in setting the output parameters of compatible constant current drivers. The controlled settings and their definitions are listed below: System Definitions EVERset Programming Software Graphical User Interface (GUI) loaded onto a computer for establishing programmed settings for compatible Everline drivers. LDPC000A Programming Tool Handheld programming tool connected to a computer via USB that is used to program select LED drivers via a wired or wireless (RFID) interface LDPCEL0A Programming Tool Handheld programming tool connected to a computer via USB that is used to program select LED drivers via a RS-232 interface UserManagement Software This program (installed along with EVERset) is used to set up new users with passwords and access level permission capabilities on a computer. Production mode settings are also established with this program. Setting Definitions Output Current This is the driver s output current when the dimming control is set at full output or when the driver is not connected to a dimming control. Minimum Dim Current: This is the driver s output current when connected to a control set to the minimum dimming control voltage. Dimming Curve: The 0-10V dimming curve can be set to Linear, Soft Start or Logarithmic. The curves are displayed with an accompanying graph in EVERset. Full Bright Control Voltage This is the minimum voltage on the 0-10V control range that will provide maximum output current. This is commonly set around 8V to allow for variances in dimming controls. Full Dim Control Voltage: This is the maximum voltage on the 0-10V control range that will provide the minimum output current. This is typically set around 1V to allow for variances in dimming controls Dim-to-off: This is the functionality that turns off the output current while the driver still has power connected to it. Dim-to-Off Control Voltage: This is the control voltage where the driver will go in the off mode. Any voltage below this will also result in the off mode. 3 P a g e

5 Lumen Maintenance This feature increases the output current of the driver over time to compensate for the lumen depreciation of the LED module. Initial and final drive currents along with the compensation period are adjustable. RFID Radio Frequency Identification for wireless programming of a driver. This uses near field communication (NFC) between the driver and the configuration tool for programming values into the driver. MDC Multi-Driver Configuration for programming or reading a compatible driver with leads connected to the LDPC000A programming tool. This can be used with specific drivers that are compatible with EVERset but do not have wireless programming capabilities. Products Products shown in this list use the EVERset software for programming. Additional products will continue to be added through updates. Profiles The saved set of all values for a specific driver setting. These can be recalled for programming. 4 P a g e

6 4. Getting Started/Setup Programming Software The Complete EVERset Program is installed with the setup file name EVERset_x.x.x.exe (x values will change with revision updates). This file may require administrator access on a computer for installation of: EVERset Program The EVERset program is used for all programming applications from creating driver configurations, saving driver profiles, to production programming. UserManagement The UserManagement program is used to manage and create user names, passwords, and to set the access levels of production, engineering and administration. For more detailed information refer to section 13 User Management Setup. Note: Administration password will be provided separately Program Data File Location A program data file will be installed in the folder C:\ProgramData\ULT that contains: Saved Program Configuration Profile files in ProfileLists Help information Driver database configuration files Programming Hardware Programming Tool: P/N LDPC000A Connect the programing tool to a USB port on the computer for programming. The programming tool has indicator lights that will illuminate when connected to a powered USB port The programming tool also has a connector receptacle for use when tuning drivers that do not have wireless tuning capabilities and require MDC wired tuning. Programming Tool: P/N LDPCEL0A Connect the programming tool to a USB port on the computer for programming. The programming tool has a RJ45 connector for use with compatible LED drivers. LED Drivers with compatible programming interface Only Everline drivers that are listed for wireless programming, MDC wired programming or ESI RS-232 programming can be programmed through EVERset. The drivers with wireless programming will have a small programming antenna that looks like a small circuit board either next to the connectors or behind a plastic cover in the side of the driver. See for a list of compatible drivers. 5 P a g e

7 Logging into EVERset Launch the EVERset program and enter the Username and Password to get started. The username and password will correspond to an account setup for engineering mode or production. This will determine the functionality allowed when EVERset is launched. See Section 8: UserManagement Setup for information on setting up user accounts. 6 P a g e

8 5. Programming Interfaces: RFID, Wired and ESI Within the Products menu bar as indicated above there is the option to Read and Program in either the RFID, Wired or ESI mode. RFID uses near field communication to perform these functions using the LDPC000A programming tool and driver antenna. RFID programming programs one driver at a time. When EVERset is in RFID read mode, the LDPC000A programming tool will be continuously looking for an RFID tag to read. Wired uses leads connected directly to the driver from the LDPC000A programming tool and communicates via MDC (Multi-Driver Configuration) for programming. The leads are connected between the configuration tool and the dimming control leads of the driver. When EVERset is in the Wired read mode, the black button on the LDPC000A programming tool must be pressed to read the driver that is connected to the tool. Each time a new driver is connected, the black button must be pressed on the LDPC000A to read the driver. Two harnesses with leads for programming are provided with the configuration tool and plug into a socket adjacent to the USB cable. One harness has fast connectors (as shown in the picture) designed to program drivers with leads. The other harness has pin terminals and is designed for use with drivers that have terminal blocks. Wired programming can program four drivers simultaneously under the following conditions: Four of the same models drivers with the same profile. Three different model drivers with two of the same drivers having the same profile. Only one profile per driver per model, different profiles of the same model cannot be programmed simultaneously. 7 P a g e

9 ESI programming uses the LDPCEL0A programming tool which has a male RJ-45 connector that connects directly to the female RJ-45 adapter on a compatible driver. When EVERset is in the ESI read mode the black Read button at the top of the screen must be clicked to read the driver connected to the LDPCEL0A programming tool. Each time a new driver is connected, the Read button must be clicked to read the driver. 8 P a g e

10 6. Engineering Mode Initial Screen Layout Products Screen 1. Indicates that the program is in the Products Screen. Note: Clicking on the adjacent Profiles tab will access the Profiles Screen. 2. The OFF indicates that the program is NOT in the Read Mode. To enter the Read Mode click on the adjacent arrow and ON will appear in green. The Mode is also displayed in the blue status ribbon. 3. This indicates the model currently on the screen for programming or developing a profile. For different models, scroll down the list and click on them. The Search window at the top of the products list can be used to limit the list for easier selection. By typing in a partial catalog number, the list can be narrowed down. Example 30 will provide only part numbers that contain 30. The same can be done with PWX or other sections of the part number. 4. The connected status indicates if the LDPC000A programming tool is connected to the computer. 5. This button expands the screen for better access to the programming sliders in lieu of showing the values in the tables. For smaller monitors, this may be beneficial when working in the Dimming setup screen. Clicking on the button a second time brings the screen back to the initial state. 6. Click on the arrow to minimize the product list. Clicking on the button a second time returns the product list back to the screen. 9 P a g e

11 Reading a Driver s Programmed Values: The current configuration of a compatible driver can be read through EVERset. Once the driver has been read, the configuration can be saved for programming or modified and programmed back to the driver through the Engineering mode. Reading a Driver s Programmed Values through the RFID Interface: Click on Products Tab (If not already selected) Click on Read Mode so that it is ON (if not already selected) Confirm RFID Button is selected Set the driver on its side and place the programming tool so that it is coplanar with the antenna. The indicator lights will change to green once the program values have been read. READ Complete will also appear momentarily on the screen. Driver Antenna 10 P a g e

12 For best results position the area indicated with the programming tool flush against the driver. directly above the driver antenna with the Example: Screen results indicate a successful read and display the driver part number and programmed values for output current, dimming curve, dim curve set points and lumen maintenance. Note: the read results can be programmed to another driver of the same model or saved as a profile for future programming. 11 P a g e

13 Reading a Driver s Programmed Values through the Wired Interface: Click on Products Tab (If not already selected) Click on Read Mode so that it is ON (if not already selected) Confirm Wired Button is selected Plug in the connector with the violet and gray leads to the LDPC000A programming tool. Squeeze the open connector on the terminal connected to the violet wire from the LDPC000A and plug the violet wire from the driver into the quick connect terminal. Repeat this process to plug the gray wire from the driver into the connector attached to the gray wire on the LDPC000A. Press the black button on the top of the LDPC000A to read the connected driver. Only one driver can be connected at a time for the Wired read process. The driver configuration will display on the screen. 12 P a g e

14 Reading a Driver s Programmed Values through the ESI Interface: Click on Products Tab (If not already selected) Click on Read Mode so that it is ON (if not already selected) Confirm ESI Button is selected Plug in the RJ45 male connector from the LDPCEL0A into the RJ45 female connector on the driver. Press the Read button on EVERset. The driver configuration will display on the screen. 13 P a g e

15 Creating a Profile 1. Select the Products tab 2. Select the driver part number to be programmed If a driver is programmable through multiple interfaces select the desired interface in the blue status bar. The program will default on the Output tab where the only configurable parameter is output current. If the dimming curve will be configured, you can go straight to the Dimming tab as the output current can also be configured there. 3. Click the expand view button for better viewing if necessary 4. Adjust the Output current with the slider bar or arrows 5. Settings can be Reset to Default if necessary 14 P a g e

16 Setting the Dimming Curve and Values 1. Select the Dimming tab to establish dimming parameters. a. The output current can also be changed on this tab to create the full dimming profile on one tab. Note: the Output Current selected on the Output tab will populate here. 2. Select the minimum Dim Current, the lowest value is determined by the driver. a. The default minimum dim current will be a percentage of the maximum output current. The percentage is dependent on the driver. When this option is selected the minimum dim current will change when the output current is changed. Once the driver reaches the lowest minimum dim current a notification message will appear and the program will toggle over to have the minimum dim current selected by ma level instead of percentage. b. The radio button above the ma box can also be selected. This will make the value static and it will no longer automatically change when the output current is changed. 3. Select the Dimming Curve: Linear, Soft Start, or Logarithmic. a. Logarithmic provides the options for different factors. This changes how steep the curve will be. 4. Set the Full Bright Control Voltage. 5. Set the Minimum Dim Control Voltage. 6. If desired, enable Dim-to-Off by setting the Dim-to-Off control voltage to >0. a. Minimum Dim Control Voltage must be >0.2V higher than Dim-to-Off Control Voltage or an error message will appear. Note: for best operation, use at least >0.5V between the minimum dim control voltage and the dim-to-off control voltage. 7. The Dim Curve Chart will adjust accordingly as the values are selected 8. The expand window button can be used to minimize the summary boxes if needed to display the full dimming curve graph on the screen. 15 P a g e

17 Setting Lumen Maintenance (when applicable): Models that have lumen maintenance capabilities will have a lumen maintenance tab displayed next to the dimming tab. Lumen maintenance allows for the driver to increase output current over the programmed compensation period to offset the lumen depreciation of the module. 1. Where applicable, click on the LUMEN MAINTENANCE Tab a. Expand the screen if necessary for better viewing. b. For best results, the Output and Dimming tabs should be configured prior to configuring Lumen Maintenance. 2. Click Enable to use the Lumen Maintenance function. a. Click Disable to disable the Lumen Maintenance function. b. The Lumen Maintenance tab will only appear for drivers that have Lumen Maintenance functionality and will not appear for others. The default setting for drivers with Lumen Maintenance is disabled. 3. Set the final output current in the field supplied. a. This is the maximum output current at the end of compensation period. b. This is the output current value that is displayed on the Output and Dimming tabs. 4. Set the initial output current in the field supplied. This value can be set between 50% and 100% of the Output Current (Final). 5. Set the Lumen Compensation Period in the field supplied. a. This is the time in hours for the driver to increase the output current from Initial to Final. b. The maximum value is 100,000 hours. 6. The Lumen Maintenance percentage value is shown below the graph. 16 P a g e

18 Saving Profiles Driver configurations can be saved as Profiles in EVERset. Saved profiles can be recalled through engineering mode or production mode for programming drivers. Saving Profiles for use with the RFID and ESI Programming Interfaces After creating a driver configuration that will be programmed with the RFID or ESI programming interface: 1. Click on Save Profile 2. In the Save Profile dialog box, click on Yes 3. In the File Name dialog box, enter the desired Profile name in the File Name field. This will be the name of the profile shown in the Profiles tab. a. The Description field is optional 4. Click OK 17 P a g e

19 Saving Profiles for use with the Wired Programming Interface Driver configurations created for use with the Wired Programming Interface have an additional step before saving the configuration as a profile. After creating the configuration: 1. Select the number of drivers to be programmed 2. Click Add to Profile 3. EVERset will switch over to the Configuration Summary List 4. If additional drivers are desired to be added to this configuration, click on the driver in the Products tab and create a new configuration. Note: Section 5 Programming Interfaces: RFID, Wired and ESI contains information on the quantities of drivers that can be programmed through the Wired Programming Interface 5. When the configuration is complete, click on Save Profile. 6. In the Save Profile dialog box, click on Yes 18 P a g e

20 7. In the File Name dialog box, enter the desired Profile name in the File Name field. This will be the name of the profile shown in the Profiles tab. The Description field is optional 8. Click OK 19 P a g e

21 Quick Programming through Engineering Mode RFID Programming 1. Set the program into Products mode and select a driver from the Products list. 2. Set Read Mode to OFF, the text below will indicate the Write mode. 3. Enable the RFID Button (if not already selected) for wireless programming 4. Click the Dimming tab to adjust the dimming parameters 5. If needed, use the Expand view button to have all of the controls on one page. 6. Adjust the programmable outputs with the numbers or slider bars The control chart will automatically adjust with changes If using Dim-to-Off Control, the minimum Dim Control Voltage must be at least 0.2V higher than the Dim-to-Off Control Voltage. An error message will appear if the difference is less than 0.2V. A Dim-to-Off Control Voltage of 0 disables this function 7. Click Program Profile This loads the configuration into the LDPC000A programming tool 8. Place the programming tool co-planar to the antenna on the driver in the same manner as reading the driver. The lights on the programming tool will display green when the driver is programmed The screen will also temporarily display that the driver has been programmed. Note: if switching to Wired or ESI programming, click the Clear button to remove the RFID configuration from the programming tool. 20 P a g e

22 Wired Programming 1. Set the program into Products mode 2. Set Read Mode to OFF, the text below will indicate the Write mode. 3. Enable the Wired Programming Button (if not already selected) 4. Click the Dimming tab to adjust the dimming parameters 5. If needed, use the Expand view button to have all of the controls on one page. 6. Adjust the programmable outputs with the numbers or slider bars The control chart will automatically adjust with changes If using Dim-to-Off Control, the minimum Dim Control Voltage must be at least 0.2V higher than the Dim-to-Off Control Voltage. An error message will appear if the difference is less than 0.2V. A Dim-to-Off Control Voltage of 0 disables this function 7. Click Add to Profile EVERset will switch over to the Configuration Summary List 21 P a g e

23 8. Click Program Profile This loads the configuration into the LDPC000A programming tool Connect the violet and gray leads from the driver to the violet and gray connectors on the LDPC000A programming tool 9. Press the black button on the top of the LDPC000A programming tool The lights on the programming tool will display green when the driver is programmed The screen will also temporarily display that the driver has been programmed 22 P a g e

24 ESI Programming 1. Set the program into Products mode 2. Set Read Mode to OFF, the text below will indicate the Write mode. 3. Enable the ESI Programming Button (if not already selected) 4. If needed, use the Expand view button to have controls on one page. 5. Adjust the output current with the numbers or slider bar 6. Click Program Profile This loads the configuration into the LDPCEL0A programming tool Connect the male RJ45 connector from the LDPCEL0A programming tool to the female RJ45 connector from the driver 7. Click the Write Button The screen will temporarily display that the driver has been programmed 23 P a g e

25 Profile Programming through Engineering Mode Profile Programming The Profile Screen allows for recalling of saved profiles and programming of these profiles through the Engineering Mode. This screen can be accessed by clicking on the Profiles tab beneath EVERset. 1. The list of available Profiles will be displayed on the left side of the screen. A profile can be found by scrolling through the list or by typing into the search box. 2. There is also an option to pull up a profile by scanning a barcode. Click on the scanner icon and then scan the barcode for the profile and EVERset will automatically load the profile. The barcode needs to be generated to match the profile name and the compatible barcode formats will depend on the specific barcode scanner that is used. 3. The selected profile will show up on the screen. Here the parameters to be programmed, along with the profile name and the driver catalog number will all be displayed. 4. Click on the Program Profile button. For specific instructions on the different programming interfaces, refer to the prior section Quick Programming through Engineering Mode. 5. The Print Label button will become active if label printing has been enabled. See section Printer Setup for instructions on setting up label printing. 24 P a g e

26 Additional Profile Options In addition to loading and programming profiles, there are additional tasks available in the Profiles screen. 1. The Edit Profile button will open up the profile into the Products Tab. From there parameters can be changed and the profile can be saved as a new profile. This is helpful when creating a series of profiles for a luminaire where the only value changing is the output current. 2. The Import Profile button can be used to load a profile from another location into EVERset. This can be used for sharing profiles during design or loading profiles into a separate computer for programming. 3. The Page icon contains the following options: a. Export Profile this allows the profile on the screen to be saved to a location other than the selected profile folder used by the computer running EVERset. b. Open Profiles Folder: Opens and shows profiles in the location the EVERset program uses. Profiles can then be copied from this location and then saved on a second computer with the EVERset software. c. Refresh Profiles: Updates profiles on screen when new ones have been loaded. This needs to be clicked if profiles have been manually loaded into the profile folder while EVERset is in use. d. Delete Profiles: Deletes the highlighted or identified Profile 25 P a g e

27 Additional Menu Options The following additional menu options can be accessed in EVERset by clicking on the gear wheel icon Load Default Database: Clicking on this option will load the default driver configuration database file. Update Configuration Database: Updates the configuration database by downloading the latest file from the internet or from a local drive. Note: When the local drive option is selected, the file needs to remain in the location pointed to during the update. If the file is moved, EVERset will revert to the default database. Printer Setup: configuration of printer setup when using a compatible printer through EVERset. See next page for detailed instructions. Folder Locations: Allows for changing the default folders for the CSV Folder, Log Folder and Profile Folder. CSV Folder this is the location where EVERset will generate CSV files after a successful programming if the CSV export option is enabled in Production mode. The default location is C:\ProgramData\ULT\CSV Log Folder this is the location where EVERset generates and stores log files of the successful driver programmings. The default location is C:\ProgramData\ULT\Logs Profile Folder this is the location where new profiles are saved to and where EVERset looks for profiles to be loaded for programming. The default location is C:\ProgramData\ULT\ProfileLists Update EVERset: Checks for the latest version of the EVERset program and provides an option to update (internet access required) Log Data: Provides an exportable table of the products that have been programmed with details of the date, time, and configuration settings. Data can also be limited by the programmed date or programmed date range. 26 P a g e

28 Printer Setup EVERset contains basic label printing for use with a Dymo LabelWriter 450 printer and 0.5 x 1.0 labels. If more customization is required in the label, the CSV export option is provided for use with a separate printing setup. 1. Click on Select Printer and highlight the Dymo LabelWriter 450 and click Apply. 2. The Dymo LabelWriter 450 will be displayed next to Printer Name. a. Check the box next to Print Both Labels if it is desired to print both labels. This selection will carryover to the Production Mode interface. The label content will be selected in step 4. b. Check the box next to Label Printing to enable label printing in the engineering mode. Enabling label printing for Production Mode is done in UserManagement. c. Check the box next to Automatic to have the engineering mode labels print automatically after a successful programming. 3. The Dymo 0.5 x 1.0 label size will be selected. No other changes need to be made to the Label Size Selector or Printer Parameters sections. 4. There are six available parameters that can be printed on the labels. The Driver Model Number, Tuned Output Current, Minimum Dim Current, Dimming Curve, Dimming Set Points and Date. The second label will only print if the box next to Print Both Labels is checked. Text lines on the label can be set to None if not needed. 5. Click Print Sample Label to verify the label setup. Note: the Dymo label roll has two labels stacked. When only one label is printed, the other label will be left blank. 6. Click Save Settings to complete the printer setup. 27 P a g e

29 7. Production Mode The Production Mode is used for production programming only with profiles that have already been saved on the computer. Users in this mode cannot create new profiles or adjust existing profiles. The production mode screen appears similar to the profiles tab in the engineering mode, but with less options. Depending on the user s permission level there will be slight variations. See Section 8: UserManagement for information on the production permissions. 1. Clicking on the Read Mode allows driver configurations to be read and displayed 2. The barcode indicator will appear when the permission is set for barcode only. See the UserManagement section for setup details. a. The user must have created a list of profiles and associated barcodes for recall using a barcode scanner. b. Manual selection of profiles is not available in this mode. 3. The Profile list appears allowing the user to select the profile for programming when enabled. See the UserManagement section for setup details. a. The gray search box allows for users to enter portions of the profile name to find it. 4. The RFID, Wired or ESI button will indicate the method for programming of the selected profile. a. The method is defined the with profile s setup, it is not selectable in production mode. 5. The program profile button must be clicked to load the program to the programming tool to begin programming of the selected profile. a. This step is not used with the barcode only permission mode. 6. The Print label button is used for printing of individual labels when label printing is enabled, but not set to the automatic mode. See the UserManagement section for setup details. 7. If enabled through UserManagement, the import profile button allows the user to load additional profiles created on a different computer into the program. Profiles created on a specific computer are always available on that computer when logged in with production permission. See the UserManagement section for setup details. 28 P a g e

30 8. UserManagement This program (installed along with EVERset) is used to set up new users with passwords and access level permission capabilities on a computer. Production mode settings are also established with this program. The initial screen will appear as shown below: Adding Users To add a user, click on Add user. You will have the choice to set the new user up with one of the following three roles: Administrator: Full access to UserManagement for creating new users and full access to engineering mode in EVERset. After a new administrator is setup, the default admin can be deleted. Engineering: No access to UserManagement. Full access to the engineering mode of EVERset to program drivers and to create profiles for production. EVERset production logs are accessible with this mode. Production: No access to UserManagement. Access to production mode of EVERset with a predefined permission set for programming drivers only from established profiles and reading programmed driver settings. Profiles cannot be changed or developed in this mode. Note: the Change Password option is available for an administrator to change a User s password. Production Permissions Production Permissions are used only for users with the Production role. They are set up to define how the production mode will be used. These permissions can be different for different users. The Default Permission button can be used to set up the default production permissions, eliminating the need to repeat the setup of production permissions when setting up many different users with the same set of permissions. Permissions can also be edited by clicking the user icon in the Production Permissions column of a specific user s row. 29 P a g e

31 Production Permission Descriptions: Profile Loading Manual Profile Loading o Users will use the mouse to select the profile to be programmed o Users can also type in partial values for a quick search to limit the number of profiles o The available profiles displayed will be the prf files that are stored in the Profile Folder. See the Additional Menu Options sections for instructions on changing the file folder. Barcode Only o A barcode reader is used to select a profile for programming o Scanning a barcode that contains the filename of the profile will automatically load the profile for progamming o The format of the barcode depends on the 3 rd party barcode reader File Folder When Load File is checked the user is given the Import Profile button that allows them to navigate to a file folder location to manually load a profile 30 P a g e

32 Programming Quantity Single Unit: o Programs one unit at a time o Program Profile button on the screen needs to be clicked after each programming event to program another driver Continuous: o Allows for continuous programming of a profile without the need to continually click on the computer o Changing to a new profile will require interaction with the GUI Batch o Allows for a specific amount (batch size) of drivers to be programmed o After selecting a profile and clicking on Program Profile, a dialog box will appear requiring the batch size to be entered. This is the number of drivers to be programmed. o The batch programming count will be displayed at the bottom of the screen. Once the batch is complete the GUI needs to be accessed again to program a new profile. Label Printing Automatic o Prints a label immediately after a successful programming event On Click o Requires the Print label button to be clicked after each programming event. The button will be disabled until a successful programming event and can only be clicked once per successful programming event to print one label. Disabled o Disables the printing function from the GUI CSV Export o Exports a CSV file to a selected location upon a successful programming event. This file can be then be used to automatically print a label through a 3 rd party label printing software. This option allows for custom label formats. 31 P a g e

WIRELESS DRIVER PROGRAMMING. EVERset Program & Configuration Tool Manual

WIRELESS DRIVER PROGRAMMING. EVERset Program & Configuration Tool Manual WIRELESS DRIVER PROGRAMMING EVERset Program & Configuration Tool Manual User Manual V1.3 12/13/2017 Table of Contents 1. Introduction 2. Computer system Requirements 3. Definitions System Definitions Setting

More information

RedBeam Inventory Tracking User Manual

RedBeam Inventory Tracking User Manual RedBeam Inventory Tracking User Manual Contact us at www.redbeam.com. Page 1 Table of Contents Table of Contents... 2 Overview... 4 RedBeam Inventory Tracking... 4 PC Prerequisites... 4 Mobile Computer

More information

Application Note: EVD09. Handheld Tuning System for Non-Powered Tuning (NPT) LED Drivers

Application Note: EVD09. Handheld Tuning System for Non-Powered Tuning (NPT) LED Drivers Application Note: EVD09 Handheld Tuning System for Non-Powered Tuning (NPT) LED Drivers For Drivers with the Logo: Overview Tuning provides the ability to set a Tunable driver s output current at levels

More information

Step Sheet: Creating a PowerPoint Presentation

Step Sheet: Creating a PowerPoint Presentation Step Sheet: Creating a PowerPoint Presentation PowerPoint Presentation This step sheet will help you create a Microsoft PowerPoint presentation. Using Microsoft PowerPoint To create a presentation, follow

More information

DATA RECORDING FOR FARMIQ

DATA RECORDING FOR FARMIQ HR/HR5 SET UP GUIDE DATA RECORDING FOR FARMIQ It is important that animal data is collected on the Gallagher hardware in the correct format, so that it can be easily imported to the FarmIQ system. The

More information

Introduction to Microsoft Office PowerPoint 2010

Introduction to Microsoft Office PowerPoint 2010 Introduction to Microsoft Office PowerPoint 2010 TABLE OF CONTENTS Open PowerPoint 2010... 1 About the Editing Screen... 1 Create a Title Slide... 6 Save Your Presentation... 6 Create a New Slide... 7

More information

worksmart!-mobile User Guide Version 3.5 worksmart!-mobile User Guide 1 Copyright 2005 Mobile Workforce, Inc.

worksmart!-mobile User Guide Version 3.5 worksmart!-mobile User Guide 1 Copyright 2005 Mobile Workforce, Inc. worksmart!-mobile User Guide 1 Copyright 2005 Mobile Workforce, Inc. Copyright Notice Mobile Workforce, Inc. has copyright ownership of the Mobile Workforce-workSmart! applications and other software related

More information

FrontPage 2000 Tutorial -- Advanced

FrontPage 2000 Tutorial -- Advanced FrontPage 2000 Tutorial -- Advanced Shared Borders Shared Borders are parts of the web page that share content with the other pages in the web. They are located at the top, bottom, left side, or right

More information

Magnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual

Magnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual Magnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual February 2006 Part Number: 140-10350 Copyright 2006 Magnetek Material Handling 2005 MAGNETEK MATERIAL HANDLING All rights reserved.

More information

SMART CURRENT SOFTWARE GUIDE

SMART CURRENT SOFTWARE GUIDE Page 1 of 6 System Requirements 1. Designed for use with computers running Windows 7 or a more recent operating system. 2. Microsoft.NET Framework 4.0 runtime 3. FTDI D2xx Driver CDM v2.12.24 or above

More information

Application Note: EVD09. Production Tuning System for Non-Powered Tuning (NPT) LED Drivers

Application Note: EVD09. Production Tuning System for Non-Powered Tuning (NPT) LED Drivers Application Note: EVD09 Production Tuning System for Non-Powered Tuning (NPT) LED Drivers 1 Initial System Setup For Drivers with the Logo: NPT Install the ULT Everline programming utility (provided on

More information

Legal Notes. Regarding Trademarks KYOCERA MITA Corporation

Legal Notes. Regarding Trademarks KYOCERA MITA Corporation Legal Notes Unauthorized reproduction of all or part of this guide is prohibited. The information in this guide is subject to change without notice. We cannot be held liable for any problems arising from

More information

E-Report. User Manual

E-Report. User Manual E-Report User Manual 2011 All rights reserved. No parts of this work may be reproduced in any form or by any means graphic, electronic, or mechanical, including photocopying, recording, taping, or information

More information

AN-619 APPLICATION NOTE

AN-619 APPLICATION NOTE APPLICATION NOTE One Technology Way P.O. Box 9106 Norwood, MA 02062-9106 Tel : 781/329-4700 Fax: 781/326-8703 www.analog.com Using the ADN8810 Demo Board v2.0 by Troy Murphy and Chris Kung OVERVIEW The

More information

NETWORK PRINT MONITOR User Guide

NETWORK PRINT MONITOR User Guide NETWORK PRINT MONITOR User Guide Legal Notes Unauthorized reproduction of all or part of this guide is prohibited. The information in this guide is subject to change for improvement without notice. We

More information

version 7.6 user manual

version 7.6 user manual version 7.6 user manual 2 Copyright JAVS 1981-2014 Table of Contents Introduction... 4 Getting Started... 5 Login... 5 JAVS Publisher 7 Overview... 6 Search Tool Overview... 7 Search Tool-Detailed Operation...

More information

Basic Millennium INTRODUCTION

Basic Millennium INTRODUCTION Basic Millennium INTRODUCTION Welcome to the Basic Millennium tutorial. Navigation tools, such as the Continue button, will display as you progress through the presentation, while playback functions are

More information

MeshConnect ISP / WNA (ZIC2410USB-WNA-1) User Guide

MeshConnect ISP / WNA (ZIC2410USB-WNA-1) User Guide MeshConnect Family MeshConnect ISP / WNA (ZIC2410USB-WNA-1) User Guide 0007-05-08-06-001 (REV B) TABLE OF CONTENTS INTRODUCTION 3 CEL MESHCONNECT ISP / WNA FEATURES 3 GETTING STARTED 4 USB SETUP 4 MESHCONNECT

More information

Quick Start Guide. MS-820 Industrial Bar Code Scanner

Quick Start Guide. MS-820 Industrial Bar Code Scanner Quick Start Guide MS-820 Industrial Bar Code Scanner This guide is designed to get your scanner up and running quickly. When connected to a host computer with Windows operating system (98 or above), you

More information

Company. Business Online Banking Admin - Company. Company - Profile. Company - BAI Settings

Company. Business Online Banking Admin - Company. Company - Profile. Company - BAI Settings Company The Company page displays information specific to your Business. Additional function tabs or sub-menus are available to view information and settings specific to the company. From here you can

More information

SP2+ Swing Handle Lock Manual

SP2+ Swing Handle Lock Manual www.akcp.com SP2+ Swing Handle Lock Manual Copyright 2016, AKCP Table of Contents Introduction... 3 Hardware features... 4 LED status description for the Handle Lock & Door Sensor... 4 Specifications FAQ

More information

vbound User Guide vbound User Guide Version Revised: 10/10/2017

vbound User Guide vbound User Guide Version Revised: 10/10/2017 vbound User Guide Version 4.1.1 Revised: 10/10/2017 Copyright 2014-2017 FFL Solutions Inc. Page 1 of 87 Table of Contents Using vbound...5 Starting vbound... 5 Bound Book List... 6 vbound Ribbon Menu...

More information

Emote 1.0 Users Manual

Emote 1.0 Users Manual Emote 1.0 Users Manual Part No: 141318 Rev A 2018 Eventide Inc., One Alsan Way, Little Ferry, NJ, 07643 USA 1 Table of Contents Introduction... 3 Downloading the Installer... 3 Making Sure Your H9000 Hardware

More information

Lab 11-1 Lab User Profiles and Tracking

Lab 11-1 Lab User Profiles and Tracking In the following lab instructions, you will be setting up groups, users, and passwords to require password-protected login to Kofax Capture modules. Rights will be assigned to the groups and users that

More information

PST for Outlook Admin Guide

PST for Outlook Admin Guide PST for Outlook 2013 Admin Guide Document Revision Date: Sept. 25, 2015 PST Admin for Outlook 2013 1 Populating Your Exchange Mailbox/Importing and Exporting.PST Files Use this guide to import data (Emails,

More information

type44legacy Manual VERIPOS

type44legacy Manual VERIPOS VERIPOS A 15/06/2012 Released for Use KC EM EM REVISION DATE DESCRIPTION ORIGINATOR CHECKED APPROVED CLIENT APPR Document Title: Type44Legacy IOLAN Manual Document No: File Ref:.doc CONTENTS 1. INTRODUCTION...3

More information

KMnet Viewer. User Guide

KMnet Viewer. User Guide KMnet Viewer User Guide Legal Notes Unauthorized reproduction of all or part of this guide is prohibited. The information in this guide is subject to change for improvement without notice. We cannot be

More information

KYOCERA Net Viewer 5.3 User Guide

KYOCERA Net Viewer 5.3 User Guide KYOCERA Net Viewer. User Guide Legal Notes Unauthorized reproduction of all or part of this guide is prohibited. The information in this guide is subject to change without notice. We cannot be held liable

More information

Table of Contents. 1 P a g e

Table of Contents. 1 P a g e Table of Contents User Manual... 2 Florida s PK-20 Education Information Portal... 2 Navigating the Portal... 2 Tabs... 3 Accessible Site... 3 Helpful Resources... 4 State Level Tab... 4 District Level

More information

I/O Configurator (NFC version) EX600-WPN# (Wireless master) EX600-WSV# (Wireless slave)

I/O Configurator (NFC version) EX600-WPN# (Wireless master) EX600-WSV# (Wireless slave) PRODUCT NAME I/O Configurator (NFC version) MODEL / Series / Product Number EX600-WEN# (Wireless master) EX600-WPN# (Wireless master) EX600-WSV# (Wireless slave) Contents 1. Introduction 3 1.1. Definition

More information

KYOCERA Net Viewer User Guide

KYOCERA Net Viewer User Guide KYOCERA Net Viewer User Guide Legal Notes Unauthorized reproduction of all or part of this guide is prohibited. The information in this guide is subject to change without notice. We cannot be held liable

More information

Content Author's Reference and Cookbook

Content Author's Reference and Cookbook Sitecore CMS 7.2 Content Author's Reference and Cookbook Rev. 140225 Sitecore CMS 7.2 Content Author's Reference and Cookbook A Conceptual Overview and Practical Guide to Using Sitecore Table of Contents

More information

Table of Contents CHILD CHECK IN OVERVIEW Check In / Out Process...3 Check In Methods...3 Name Tags and Security Tags...5 Check Out...

Table of Contents CHILD CHECK IN OVERVIEW Check In / Out Process...3 Check In Methods...3 Name Tags and Security Tags...5 Check Out... Table of Contents CHILD CHECK IN OVERVIEW Check In / Out Process...3 Check In Methods...3 Name Tags and Security Tags...5 Check Out...6 INSTALLING ROLL CALL for CHILD CHECK-IN Hardware/Software Requirements...7

More information

User Guide Ahmad Bilal [Type the company name] 1/1/2009

User Guide Ahmad Bilal [Type the company name] 1/1/2009 User Guide Ahmad Bilal [Type the company name] 1/1/2009 Contents 1 LOGGING IN... 1 1.1 REMEMBER ME... 1 1.2 FORGOT PASSWORD... 2 2 HOME PAGE... 3 2.1 CABINETS... 4 2.2 SEARCH HISTORY... 5 2.2.1 Recent

More information

8380 RPC Return Path Combiner. User s Guide

8380 RPC Return Path Combiner. User s Guide 8380 RPC Return Path Combiner User s Guide Notice Every effort was made to ensure that the information in this manual was accurate at the time of printing. However, information is subject to change without

More information

SATO Online Services User s Manual May 19, 2017 Version 1.0

SATO Online Services User s Manual May 19, 2017 Version 1.0 SATO Online Services User s Manual May 19, 2017 Version 1.0 Contents 1. Revision History... 3 2. Introduction... 4 2-1. Network connection (real-time)... 4 2-2. QR code connection (on-demand)... 4 2-3.

More information

Creating Reports using Report Designer Part 1. Training Guide

Creating Reports using Report Designer Part 1. Training Guide Creating Reports using Report Designer Part 1 Training Guide 2 Dayforce HCM Creating Reports using Report Designer Part 1 Contributors We would like to thank the following individual who contributed to

More information

Options. Parts List. Optional Expansion Hub Optional Ignition Module Optional Memory Card

Options. Parts List. Optional Expansion Hub Optional Ignition Module Optional Memory Card Options Optional Expansion Hub Optional Ignition Module Optional Memory Card View boost, speed, and gear on the LCD Display. View the ignition changes on the LCD Display. Log and store map data. Card storage

More information

Quick Start Guide. 1. Unpacking your LabelWriter Printer. Follow these steps to install the LabelWriter printer and print your first label.

Quick Start Guide. 1. Unpacking your LabelWriter Printer. Follow these steps to install the LabelWriter printer and print your first label. Quick Start Guide Copyright 2009 Sanford, L.P. All rights reserved. Revised 4/09. No part of this document or the software may be reproduced or transmitted in any form or by any means or translated into

More information

Quick Start. MS-9 Laser Scanner

Quick Start. MS-9 Laser Scanner Quick Start MS-9 Laser Scanner This guide is designed to get your scanner up and running quickly. When connected to a host computer with Windows operating system (2000 or above), you can use ESP (Easy

More information

Raptor University. Installing Raptor v Instructor: RAPTOR TECHNOLOGIES, LLC

Raptor University. Installing Raptor v Instructor: RAPTOR TECHNOLOGIES, LLC Raptor University Installing Raptor v6.1.5 Instructor: RAPTOR TECHNOLOGIES, LLC This presentation includes the following information: System Prerequisites Access Raptor Support Center Install All Components

More information

TECHNICAL TRAINING LAB INSTRUCTIONS

TECHNICAL TRAINING LAB INSTRUCTIONS In this lab, you are going to add some batch fields for associating batch-level data with every document in your batch. You will learn how to configure and test an optical mark recognition (OMR) zone for

More information

AirStick S-ID User Guide

AirStick S-ID User Guide AirStick S-ID User Guide User Manual Version 1.0 Contents 1. Definition... 4 2. Introduction... 5 Description... 5 Install S-ID... 5 Launch S-ID software... 6 Connect AirStick reader to S-ID... 7 PC and

More information

Driscoll's. Gator Nursery System. Version 2.0

Driscoll's. Gator Nursery System. Version 2.0 Driscoll's Gator Nursery System Version 2.0 Copyright 2015 Driscoll's. All rights reserved. Information in this document is subject to change without notice. The software described in this document is

More information

Command Center Software Specification for the M11x platform Version 1.0

Command Center Software Specification for the M11x platform Version 1.0 Command Center Software Specification for the M11x platform Version 1.0 CONTACT: EMAIL: Carlos Mimoso carlos_mimoso@dell.com DATE: 10/14/2010 Unlimited distribution subject to the copyright. Disclaimers

More information

U.S. Pharmacopeia Pharmacopeial Forum. USP-PF Online Quick Start Guide

U.S. Pharmacopeia Pharmacopeial Forum. USP-PF Online Quick Start Guide U.S. Pharmacopeia Pharmacopeial Forum USP-PF Online Quick Start Guide Contents GETTING STARTED... 2 Document Conventions... 2 Technical Requirements... 2 LOGIN AND LOGOFF... 2 Logging On... 3 Logging Off...

More information

Calendar & Buttons Dashboard Menu Features My Profile My Favorites Watch List Adding a New Request...

Calendar & Buttons Dashboard Menu Features My Profile My Favorites Watch List Adding a New Request... remitview User Guide 1 TABLE OF CONTENTS INTRODUCTION... 3 Calendar & Buttons... 3 GETTING STARTED.... 5 Dashboard.... 7 Menu Features... 8 PROFILE.... 10 My Profile... 10 My Favorites... 12 Watch List...

More information

The Portable Document Format (PDF) Converting word or Excel or PowerPoint to PDF PDF. PDF Save as Type. 5. When Finished Click at Save

The Portable Document Format (PDF) Converting word or Excel or PowerPoint to PDF PDF. PDF Save as Type. 5. When Finished Click at Save The Portable Document Format () The Portable Document Format () is a file format used to present documents in a manner independent of application software, hardware, and operating systems. [3] Each file

More information

Discovering Computers & Microsoft Office Office 2010 and Windows 7: Essential Concepts and Skills

Discovering Computers & Microsoft Office Office 2010 and Windows 7: Essential Concepts and Skills Discovering Computers & Microsoft Office 2010 Office 2010 and Windows 7: Essential Concepts and Skills Objectives Perform basic mouse operations Start Windows and log on to the computer Identify the objects

More information

RC-SV Configuration Guide (Rev 4)

RC-SV Configuration Guide (Rev 4) Kramer Electronics, Ltd. RC-SV Configuration Guide (Rev 4) Software Version 2.1.2.69 Intended for Kramer Technical Personnel or external System Integrators. To check that you have the latest version, go

More information

Specification Manager

Specification Manager Enterprise Architect User Guide Series Specification Manager Author: Sparx Systems Date: 30/06/2017 Version: 1.0 CREATED WITH Table of Contents The Specification Manager 3 Specification Manager - Overview

More information

Sirius Lighting Design User Manual

Sirius Lighting Design User Manual Sirius Lighting Design User Manual Updated 21 Mar, 2016 Page 1 / 32 Table of Contents 1 Introduction... 3 2 System requirements... 4 3 Interface board... 5 4 GUI for Sirius Lighting Design... 6 4.1 Main

More information

remote lockbox capture User Guide

remote lockbox capture User Guide remote lockbox capture User Guide 1 TABLE OF CONTENTS INTRODUCTION... 3 Software Prerequisites... 3 Printing Requirements.... 4 GETTING STARTED.... 5 Login...............................................................

More information

Using the VSOM Operator Pages

Using the VSOM Operator Pages CHAPTER 8 The VSOM Operator Pages provide access to features that video surveillance operators can use to view, record, search, and control video. This chapter describes the Operator Pages in detail. It

More information

Dell Rugged Control Center. Version 2.3 User s Guide

Dell Rugged Control Center. Version 2.3 User s Guide Dell Rugged Control Center Version 2.3 User s Guide Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates

More information

Maxwell RSC Tablet PC Configuration Manual for use with Windows 8 Operating System

Maxwell RSC Tablet PC Configuration Manual for use with Windows 8 Operating System Maxwell RSC Tablet PC Configuration Manual for use with Windows 8 Operating System TM537 1/18 Table of Contents 1 Maxwell RSC Instrument and Tablet PC...1 2 Glossary...3 3 Adjusting Volume Settings...5

More information

Trademark. Cadex C5100 BatteryStore v1.5 User Guide

Trademark. Cadex C5100 BatteryStore v1.5 User Guide v1.5 Trademark C5100 BatteryStore is a trademark of Cadex Electronics Inc. All other trademarks or registered trademarks mentioned herein are the property of their respective owners. Copyright Notice Copyright

More information

HP AP5000 Installation Guide (XP)

HP AP5000 Installation Guide (XP) One Blue Hill Plaza, 16th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 HP AP5000 Installation Guide (XP) This document provides step-by-step

More information

AgentWorks Administrator/Manager Functions Guide R10

AgentWorks Administrator/Manager Functions Guide R10 AgentWorks Administrator/Manager Functions Guide R10 11/21/2012 2012 MoneyGram InternationalAll rights reserved. Table of Contents 1. App Configuration... 2 2. Create Users... 4 3. Edit User Profile...

More information

ProjectorNetTM Adapter Quick Start Guide

ProjectorNetTM Adapter Quick Start Guide ProjectorNetTM Adapter Quick Start Guide Adapter networking 1. Quick Start The ProjectorNet Adapter kit contains the following items: ProjectorNet Serial to Ethernet Adapter Cable Adapter, ProjectorNet

More information

Programmable LED Driver Configuration Tool User Manual

Programmable LED Driver Configuration Tool User Manual Programmable LED Driver Configuration Tool User Manual Please send feedback or ask support questions by emailing software@erp-power.com ERP Power, LLC 893 Patriot Drive #E Moorpark, CA 93021 +1-805-517-1300

More information

Version 1.6. UDW+ Quick Start Guide to Functionality. Program Services Office & Decision Support Group

Version 1.6. UDW+ Quick Start Guide to Functionality. Program Services Office & Decision Support Group Version 1.6 UDW+ Quick Start Guide to Functionality Program Services Office & Decision Support Group Table of Contents Access... 2 Log in/system Requirements... 2 Data Refresh... 2 00. FAME Chartfield

More information

Getting Started With the CCPilot VI and QuiC

Getting Started With the CCPilot VI and QuiC Page 1 of 24 Getting Started With the CCPilot VI and QuiC Page 2 of 24 Table of Contents Purpose... 3 What You Will Need... 4 Install the QuiC Tool... 6 Install the QuiC Runtime... 7 Basics of the QuiC

More information

Beginner s Training Manual

Beginner s Training Manual Table of Contents Designing an App... 2 Modify Existing App... 12 Adding a Database... 13 Adding Controls to an Activity... 17 Activity Controls: Logic and Setup... 21 System Settings... 27 Designing the

More information

USER S MANUAL FOR UNDER VEHICLE INSPECTION SYSTEM PORTABLE AND IN GROUND UNITS

USER S MANUAL FOR UNDER VEHICLE INSPECTION SYSTEM PORTABLE AND IN GROUND UNITS USER S MANUAL FOR UNDER VEHICLE INSPECTION SYSTEM PORTABLE AND IN GROUND UNITS Revision Date Description Initials 0 2017 01 02 New template LR Index Chapter 1 INTRODUCTION... 3 Chapter 2 OPERATING INSTRUCTIONS...

More information

DT400 Series Software Utility Manual Last Updated: May 23, 2013

DT400 Series Software Utility Manual Last Updated: May 23, 2013 For Windows Mobile 6 Using the System Utility The System Utility program can be launched by pressing the front button to allow user enable/disable WiFi, Bluetooth, RFID, MSR and Scanner, adjust the LCD

More information

1 How do I download my PrimeTest 350 to PATGuard 2?... 2 How do I upload my PrimeTest 350 from. 4 How do I upload a logo to my tester for printing?...

1 How do I download my PrimeTest 350 to PATGuard 2?... 2 How do I upload my PrimeTest 350 from. 4 How do I upload a logo to my tester for printing?... Table of Contents Page 1 How do I download my PrimeTest 350 to PATGuard 2?... 2 How do I upload my PrimeTest 350 from PATGuard 2?... 3 How to update the PrimeTest 350 Firmware.... 4 How do I upload a logo

More information

child check-in quick start version 12

child check-in quick start version 12 child check-in quick start version 12 CHILD CHECK IN OVERVIEW Check In / Out Process The child check in system in Roll Call allows you to check students into their classes, record attendance and print

More information

Creating Interactive PDF Forms

Creating Interactive PDF Forms Creating Interactive PDF Forms Using Adobe Acrobat X Pro for the Mac University Information Technology Services Training, Outreach, Learning Technologies and Video Production Copyright 2012 KSU Department

More information

OneView. User s Guide

OneView. User s Guide OneView User s Guide Welcome to OneView. This user guide will show you everything you need to know to access and utilize the wealth of information available from OneView. The OneView program is an Internet-based

More information

RFID Tracking Pad Monitor

RFID Tracking Pad Monitor RFID Tracking Pad Monitor User Guide Version 3.x 3M Track and Trace Solutions 3M Center, Building 22-4N-14 St. Paul, Minnesota 144-1 78-8123-992-8, Rev. E 23-29 3M. All rights reserved. 3M RFID Tracking

More information

Supplier SAP SNC User Guide

Supplier SAP SNC User Guide Supplier SAP SNC User Guide Version 1.0 July 29, 2014 AGCO Corporation Page 1 1 Introduction AGCO has chosen SAP Supplier Network Collaboration (SNC) to improve visibility and capability in North America

More information

Lab 12-1 Lab Kofax Capture Import Connector -- XML

Lab 12-1 Lab Kofax Capture Import Connector -- XML In the following lab instructions, you are going to configure using Kofax Capture Import Connector -- XML (KCIC XML) to import documents into Kofax Capture. An XML file will provide the information for

More information

FSA-CU Configuration Utility Programming Guide

FSA-CU Configuration Utility Programming Guide FSA-CU Configuration Utility Programming Guide Revision 3 October 2013 Introduction The following guide will show you the basics of the FSA-CU configuration utility program. The CU can be used with the

More information

Quick Start. MS-9 Laser Scanner

Quick Start. MS-9 Laser Scanner Quick Start MS-9 Laser Scanner This guide is designed to get your scanner up and running quickly. When connected to a host computer with Windows operating system (2000 or above), you can use ESP (Easy

More information

TempLog & RH/TempLog User Guide. Sixth Edition First print Printed in July

TempLog & RH/TempLog User Guide. Sixth Edition First print Printed in July TempLog & RH/TempLog User Guide Sixth Edition First print Printed in July 2003 www.4oakton.com Contents Using the Guide... 15 Chapter 1 OaktonLog... 17 1.1. Overview... 18 1.2. Getting Started... 19 1.3.

More information

CREE SMARTCAST PoE TECHNOLOGY. 68% Current Savings $ SMARTCAST MANAGER USER MANUAL VERSION: Health ADVANCED. 30 Days 30 Hours 30 Min.

CREE SMARTCAST PoE TECHNOLOGY. 68% Current Savings $ SMARTCAST MANAGER USER MANUAL VERSION: Health ADVANCED. 30 Days 30 Hours 30 Min. 68% Current Savings Occupancy Task Tuning Dimming Daylight Fixture Savings 900 kwh Usage 30 Days 30 Hours 30 Min. 800 kwh 700 kwh Usage Baseline 827kWh Savings 600 kwh 500 kwh 400 kwh 300 kwh 489 kwh 30

More information

RC-SV Configuration Guide Revision 3

RC-SV Configuration Guide Revision 3 Kramer Electronics, Ltd. RC-SV Configuration Guide Revision 3 Software Version 2.1.2.32 Intended for Kramer Technical Personnel or external System Integrators. To check that you have the latest version,

More information

Copyright 2017 Xi'an NovaStar Tech Co., Ltd. All Rights Reserved. No part of this document may be copied, reproduced, extracted or transmitted in any

Copyright 2017 Xi'an NovaStar Tech Co., Ltd. All Rights Reserved. No part of this document may be copied, reproduced, extracted or transmitted in any Product Version: Document Number: SmartLCT Screen Configuration Software V3.2.0 NS110100363 Copyright 2017 Xi'an NovaStar Tech Co., Ltd. All Rights Reserved. No part of this document may be copied, reproduced,

More information

eschoolplus+ Cognos Query Studio Training Guide Version 2.4

eschoolplus+ Cognos Query Studio Training Guide Version 2.4 + Training Guide Version 2.4 May 2015 Arkansas Public School Computer Network This page was intentionally left blank Page 2 of 68 Table of Contents... 5 Accessing... 5 Working in Query Studio... 8 Query

More information

Numbers Basics Website:

Numbers Basics Website: Website: http://etc.usf.edu/te/ Numbers is Apple's new spreadsheet application. It is installed as part of the iwork suite, which also includes the word processing program Pages and the presentation program

More information

5 Working With Studies

5 Working With Studies 5 Working With Studies The Terason software provides many tools for you to work with studies. These tools allow: Storing Images and Loops; see page 90 Reviewing Patient Studies; see page 92 Exporting Studies;

More information

Outlook Quick Start Guide

Outlook Quick Start Guide Getting Started Outlook 2013 Quick Start Guide File Tab: Click to access actions like Print, Save As, etc. Also to set Outlook Options. Quick Access Toolbar: Add your mostused tool buttons to this customizable

More information

PI Scanner User Guide

PI Scanner User Guide PI Scanner User Guide Table of Contents 1. Highlights 2. Overview 3. Installation 3.1. PI Scanner Software Installation 3.2. USB to Serial Interface Board Installation 3.3. Programming the PI Scanner IP

More information

Teamcenter Mobility Product decisions, anywhere, anytime. Features. Siemens AG All Rights Reserved.

Teamcenter Mobility Product decisions, anywhere, anytime. Features. Siemens AG All Rights Reserved. Teamcenter Mobility Product decisions, anywhere, anytime Features Settings App settings are located in the ipad Settings application. Page 2 Settings Toggles in the Settings pane allow you to hide tabs

More information

Wireless RAK system setup guide

Wireless RAK system setup guide Wireless RAK system setup guide 1 What you need to get started 2 Create a new Rasoft Pro Project File 2.1 Project name and House numbers 2.2 Save Locations 2.3 Adding rooms 2.4 Adding channels 2.5 Adding

More information

Design Flow Highlights

Design Flow Highlights Design Flow Highlights Components Selection turboconfigurator Output Documentation Special Functionality Library Control System Schematic Capture Transfer 3D Models Export and Import designs (Important

More information

Astra Schedule User Guide Scheduler

Astra Schedule User Guide Scheduler Astra Schedule User Guide 7.5.12 Scheduler 1 P a g e ASTRA SCHEDULE USER GUIDE 7.5.12... 1 LOGGING INTO ASTRA SCHEDULE... 3 LOGIN CREDENTIALS... 3 WORKING WITH CALENDARS... 4 CHOOSING A CALENDAR AND FILTER...

More information

Basic Navigation in Xtender

Basic Navigation in Xtender Basic Navigation in Xtender https://scan.iit.edu/appxtender/ Xtender is used by Illniois Institute of Technology to scan in paper documents for easy accessibility. Documents scanned within Xtender are

More information

Status Bar: Right click on the Status Bar to add or remove features.

Status Bar: Right click on the Status Bar to add or remove features. Outlook 2010 Quick Start Guide Getting Started File Tab: Click to access actions like Print, Save As, etc. Also to set Outlook options. Ribbon: Logically organizes Command Buttons onto Tabs and Groups

More information

Race Keeper Pectel ECU Data Module User Guide v1.1 January 2012

Race Keeper Pectel ECU Data Module User Guide v1.1 January 2012 Race Keeper Pectel ECU Data Module User Guide v1.1 January 2012 Trivinci delivers user guides exclusively in soft format Trivinci Systems, LLC Race Keeper Pectel ECU Data Module User Guide v1.1, January

More information

AKCess Pro Server Access Control User Manual

AKCess Pro Server Access Control User Manual www.akcp.com AKCess Pro Server Access Control User Manual Help Version updated till version 118 Copyright 2012, AKCess Pro Co., Ltd.. 1) Introduction A) What is the AKCess Pro Server / Access Control?

More information

XTS36 Touch Screen X10 Lighting Control System Operating Manual

XTS36 Touch Screen X10 Lighting Control System Operating Manual X10 Lighting Control System Operating Manual 1 X10 Lighting Control System Operating Manual Rev 1.2 Introduction...3 Software Overview...4 How to Install...5 USB Driver Installation...6 Configuration Software

More information

Magnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual

Magnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual Magnetek Material Handling IMPULSE LINK 4.1 Basic Instruction Manual March 2013 Part Number: 140-10350 R6 Copyright 2013 Magnetek Material Handling 2013 MAGNETEK MATERIAL HANDLING All rights reserved.

More information

VALO ecommerce User Guide. VALO Commerce

VALO ecommerce User Guide. VALO Commerce VALO ecommerce User Guide VALO Commerce Table of Contents Introduction to VALO Commerce... 1 Using VALO Commerce... 1 Access Your Commerce Site... 2 Browse the Catalog... 4 Customize an Item... 6 Place

More information

3M Wireless Drive-Thru System Model G5 Technical Bulletin # 164

3M Wireless Drive-Thru System Model G5 Technical Bulletin # 164 3M Wireless Drive-Thru System Model G5 Technical Bulletin # 164 3M Wireless Communication System Model XT-1 Basestation Software Upgrade Overview: In the past you have conducted XT-1 Basestation software

More information

This is an example of a data filter which would allow this specific FormImprint user to see those patients with a room number between 135 and 156.

This is an example of a data filter which would allow this specific FormImprint user to see those patients with a room number between 135 and 156. FormImprint The FormImprint module is used for on-demand printing of forms. Blank forms and forms with data can be printed as needed. The screen below shows a typical FormImprint screen. The steps to printing

More information

Fast, flexible and in control

Fast, flexible and in control - Océ Posterizer Enterprise Data Entry Fast, flexible and in control o User manual Application guide Copyright 2010 Océ All rights reserved. No part of this work may be reproduced, copied, adapted, or

More information

User Manual Australia

User Manual Australia User Manual Australia April 2009 EAZ0057B06A Rev. A Trademarks Acknowledgements Snap-on, ShopStream Connect, ETHOS, MODIS, SOLUS, SOLUS PRO, and Vantage PRO are trademarks of Snap-on Incorporated. All

More information

Pulsed Frequency TM. Plasma Software Download, Installation and User Guide

Pulsed Frequency TM. Plasma Software Download, Installation and User Guide Pulsed Frequency TM Plasma Software Download, Installation and User Guide Contents Account Registration... 3 Create an Account... 4 Download the Software... 6 Install the Software... 9 Connect PLAZOMICS

More information