Map Reconfiguration User Guide

Transcription

1 Map Reconfiguration User Guide Toyota Touch 2 with Go (Low/High) 1. Background If your navigation system has software version or later, the pre installed map will either be East Europe or West Europe. This user guide takes you through the required steps should you wish to customise ( configure ) your map such that countries are added or deleted to suit your needs. The countries defined within East Europe and West Europe map are listed in Appendix A. 2. Check Software version Whether or not you have a configurable map depends on the software version of your navigation device. To check the software version, please go to your navigation device and follow the steps below. Push the SETUP hard key Push General Scroll down to the last page Push System information The map & software versions are then shown on the screen as marked below. If you have a software version lower than 4.4.0, the map is not configurable. The full EU map is always installed. Performing a map update will give the possibility to reconfigure the map.

2 3. Reconfigure the map The following section describes the steps needed to reconfigure the map. This means changing the maps installed on the device without performing a software/map upgrade. Reconfiguring is only possible as from software version Previous versions always have the full EU map installed. More information on software versions can be found in Appendix B. To perform the reconfiguration, you need a USB key containing the update files from the specific version of the device (see section 2). All versions as from will be available for download from My Toyota Customer Portal ( 3.1 Obtain reconfiguration material Visit the e Store of the Customer Portal. Select Maps tab.

3 Select Map of Europe. In order to provide you the correct map database for reconfiguring the map on your navigation device, we need to know your software version. Click on the button Show me how to proceed. This will open a page, where you can enter your current software version.

4 After confirming your software version, following screen appears: Select your vehicle (if you have more than one device/vehicle registered) and press the Download button to initiate the download of the full map of Europe, matching your software version. First you will need to accept Terms & Conditions to proceed. A ZIP file will be downloaded on your PC. You will need to unzip the downloaded file before copying to a USB stick. NOTE: The USB stick needs to be FAT 32 formatted, with a capacity of 8 GB or greater. The USB stick memory should be empty. To check if this is the case, or to get more details, insert the USB stick into you PC / laptop and right click on the USB icon. Please note that the software should be copied to the root file structure of the USB stick, and not saved to any other directories or folders. After unzipping and copying the content to a USB key, verify that the following files/directories are in the root directory: nav (= directory) KaliSWDL.log swdl.iso swdl.iso.md5 swdlinstall.iso swdlinstall.iso.md5 Once you have copied the map update content to your USB stick, you can start the map configuration process on your navigation device.

5 3.2 Performing the reconfiguration To start the update process, insert the USB stick into your navigation device. The following screen will appear: You will then be requested to confirm that you wish to reconfigure the map. Entering Yes to proceed will bring up the following screen, allowing you to select your region. In this example, West Europe is selected. For the full list of countries in each region, see Appendix A. You can also select on a country by country basis using the Select by country button which brings you to the following screen. Here you can choose a custom set of countries, as well as checking how much system memory your selection uses ( Your percentage ). The estimated time to upload the changes to your device is also shown. Once you are satisfied which your selection, press the Update button. When starting the update from the country screen you will get the following message. Select OK to proceed with the system update.

6 During the update, the engine has to keep running. Press Confirm to acknowledge that the engine is running. The radio will then reset to start the update process (this can take up to 1 minute). The system will then execute the reconfiguration process. Once the update is completed, you will see the following screen. Remove the USB key to start using the reconfigured map. Please note that a single journey from East to West or vice versa is still possible as long as the countries along the route are available in the configured map.

7 Appendix A Albania Andorra Austria Belgium Bosnia & Herzegovina Bulgaria Croatia Czech Republic Denmark Estonia Finland France FYROM Germany Gibraltar Greece Hungary Iceland Ireland Italy Kosovo WEST MAP Latvia Liechtenstein Lithuania Luxembourg Malta Monaco Montenegro Netherlands Norway Poland Portugal Romania San Marino Serbia Slovakia Slovenia Spain Sweden Switzerland UK Vatican Albania Austria Belarus Bosnia & Herzegovina Bulgaria Croatia Czech Republic Estonia Finland FYROM Germany Greece Hungary Italy Kazakhstan EAST MAP Kosovo Latvia Lithuania Moldova Montenegro Poland Romania Russia San Marino Serbia Slovakia Slovenia Turkey Ukraine Vatican

8 Appendix B List of software versions which support / do not support configurable map: Non configurable Map Configurable Map starts from L L/H L/H L/H L/H L/H