Combo Digital Video Recorder Quick Start Guide

Transcription

1 Combo Digital Video Recorder Quick Start Guide 1

2 Table of Contents 1 Hardware Installation and Connection Check Unpacked Combo DVR About Front Panel and Rear Panel Device Installation HDD Installation Front Panel and Side Panel Rear Panel Connection Sample Alarm Input and Output Connection Alarm Input and Output Details Alarm Input Port Alarm Output Port Overview of Navigation and Controls Login, Logout & Main Menu Login Main Menu Logout Auto Resume after Power Failure Live Viewing Schedule Manual Record Encode Snapshot Image FTP Search and Playback Basic Operation Network Setup

3 2.8 Pan/Tilt/Zoom PTZ Setup PTZ Operation D Intelligent Positioning Key Web Client Operation Network Connection Login Main Window

4 Welcome Thank you for purchasing our combo DVR! This quick start guide will help you become familiar with our combo DVR in a very short time. Here you can find hardware installation,cable connection information and general operations such as system setup, record, search, backup, alarm setup, PTZ operation, also here you can find web operation instruction. Before installation and operation, please read the following safeguard and warning carefully! 4

5 Important Safeguards and Warnings 1.Electrical safety All installation and operation here should conform to your local electrical safety codes. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation. 2.Transportation security Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation. 3.Installation Keep upwards. Handle with care. Do not apply power to the combo DVR before completing installation. Do not place objects on the combo DVR 4.Qualified engineers needed All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair. 5.Environment This series product working temperature ranges from 0 to 40. The combo DVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc. Please unplug the power cable in case there is strong wind or lightning. 6. Accessories Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components are included. Contact your local retailer ASAP if something is broken in your package. 7. About the LCD During the installation, do not push or squeeze the LCD or its rim; it may result in LCD damage. During the operation or storage, please avoid the hard object to scuff the screen. Please keep the LCD clean. Use the soft cloth to clean regularly. Do not use gasoline, alcohol or other chemical reagent to clean the screen. Do not allow the LCD video standstill for a long time; it may result in permanent damage. 7. Lithium battery Improper battery use may result in fire, explosion, or personal injury! When replace the battery, please make sure you are using the same model! 5

6 1 Hardware Installation and Connection Note: All the installation and operations here should conform to your local electric safety rules. 1.1 Check Unpacked Combo DVR When you receive the combo DVR from the forwarding agent, please check whether there is any visible damage. The protective materials used for the package of the combo DVR can protect most accidental clashes during transportation. Then you can open the box to check the accessories. Please check the items in accordance with the list on the warranty card (Remote control is optional). Finally you can remove the protective film of the combo DVR. Note Remote control is not a standard accessory and it is not included in the accessory bag. 1.2 About Front Panel and Rear Panel For detail information of the function keys in the front panel and the ports in the rear panel, please refer to the appendix for detail information. The model in the front panel is very important; please check according to your purchase order. The label in the rear panel is very important too. Usually we need you to represent the serial number when we provide the service after sales. 1.3 Device Installation The series product supports two installation modes: desktop/ wall-mount. The default installation is the desktop type. Please refer to the following figure. See Figure 1-1. Please purchase the wall mount accessories for wall mount type installation. Figure 1-1 6

7 1.4 HDD Installation This series combo DVR has only one SATA HDD. Please use HDD of 7200rpm or higher. You can refer to the Appendix in the user s manual for recommended HDD brand. You can select the capacity as your requirement. Please follow the instructions below to install the HDD. 1. Insert the key to the hole and then press. Turn the clockwise 90 degrees to open the lock. 2. Loose the two screws of the HDD cover. 3. Remove the HDD cover from the rear panel. 4. Connect the HDD cable and power cable. 5. Place the HDD cover to the HDD in accordance with the four holes. 6. Use the screws to fix the HDD on the cover. 7

8 7. Place the HDD with the HDD cover back to the slot. And then fix the two screws firmly. 8. Insert the key to the hole and then press. Turn the counter clockwise 90 degrees to secure the lock. After completing HDD installation, please check connection of data ribbon and power cord. 1.5 Front Panel and Side Panel The front panel is shown as in Figure 1-2. Figure 1-2 Please refer to the following sheet for front panel button information. SN Function 1 When the device is off, press it for a long time to boot up the device. When the device is on press it for a long time to shut down the device. When the device is off, press it for a short time to close the screen. 2 Power indication light 3 Remote control signal receiver window. It is to receive the signal from the remote control. 4 Mode button. It is to switch between the PC input signal and the main board signal. 8

9 5 Switch the current activated control. Go upward. Modify setup, such as increase the number. Auxiliary function such as control and switch the PTZ menu. 6 Switch the current activated control. Go downward. Modify setup, such as decrease the number. Auxiliary function such as control and switch the PTZ menu. 7 Switch the current activated control. Go left. It is to adjust the playback control bar when playback. 8 Switch the current activated control. Go right. It is to adjust the playback control bar when playback. 9 Go back to the previous menu or cancel current selection. Go back to real-time monitor status in playback mode. 10 Confirm current operation. Go to the default button Go to the menu. 11 Bidirectional talk output 12 Bidirectional talk input 13 USB port 1.6 Rear Panel The rear panel is shown as below. See Figure 1-3. Figure 1-3 Please refer to the following sheet for detailed information. SN Function 1 Power button 2 Power input port 3 Alarm input/alarm output/rs485 port 4 Network port 5 USB port 6 RS232 port 7 HDMI port 8 PC input 9 Video CVBS input, audio CVBS input, video CVBS output, audio CVBS output. 9

10 When connect the Ethernet port, please use straight cable to connect the PC and use the crossover cable to connect to the switcher or router. 1.7 Connection Sample Please refer to Figure 1-4 for connection sample. Figure Alarm Input and Output Connection There are two alarm input types for you to select: normal open (NO) and normal close (NC) Alarm Input and Output Details AB Connection port Figure

11 You can refer to the following sheet and Figure 1-6 for alarm input and output information. Parameter Grounding Alarm Ground line Alarm Input 1-NO C, 2-NO C, CTRL 12V A/B 1, 2,, 8. It becomes valid in low voltage. Two NO activation outputs. It Is to control the power output You need to close the device power to cancel the alarm. 485 communication port. They are used to control devices such as PTZ. Please parallel connect 120TΩ between A/B cables if there are too many PTZ decoders.t Alarm Input Port Please refer to the following sheet for more information. Normal open or Normal close type Please parallel connect COM end and GND end of the alarm detector (Provide external power to the alarm detector). Please parallel connect the Ground of the combo DVR and the ground of the alarm detector. Please connect the NC port of the alarm sensor to the combo DVR alarm input(alarm) Use the same ground with that of combo DVR if you use external power to the alarm device. Figure Alarm Output Port 3 ways relay alarm output (NO contact). Provide external power to external alarm device. To avoid overloading, please read relay parameters sheet in the User s Manual carefully. RS485 A/B cable is for the A/B cable of the PTZ decoder. 11

12 2 Overview of Navigation and Controls Before operation, please make sure you have properly installed HDDs and all the cable connections. 2.1 Login, Logout & Main Menu Login After system booted up, default video display is in multiple-window mode. Click Enter or left click mouse, you can see the login interface. See Figure 2-1. System consists of four accounts: Username: admin. Password: admin. (administrator, local and network) Username: Password: (administrator, local only) Username: Passwords: (Lower authority user who can only monitor, playback, backup and etc.) Username: default. Password: default(hidden user) You can use USB mouse, front panel, remote control (not included in the accessory bag) or keyboard to input. About input method: Click to switch between numeral, English character (small/capitalized) and denotation. Note: For security reason, please modify password after you first login. Within 30 minutes, three times login failure will result in system alarm and five times login failure will result in account lock! Figure Main Menu After you logged in, the system main menu is shown as below. See Figure 2-2. There are total six icons: search, information, setting, backup, advanced and shutdown. You can move the cursor to highlight the icon, and then double click mouse to enter the submenu. Figure

13 2.1.3 Logout There are two ways for you to log out. The first one is from menu option: In the main menu, click shutdown button, you can see an interface is shown as below. See Figure 2-3. Figure 2-3 There are several options for you. See Figure 2-4. Figure 2-4 The other ways is to press power button on the front panel for at least 3 seconds, system will stop all operations. Then you can click the power button in the front panel to turn off the combo DVR. Please note, before you replace the HDD, do remember shutting down the device and unplug the power cable Auto Resume after Power Failure The system can automatically backup video and resume previous working status after power failure. 2.2 Live Viewing After you logged in, the system is in live viewing mode by default. You can see system date, time and channel name. If you want to change system date and time, you can refer to general settings (Main Menu->Setting->General). If you want to modify the channel name, please refer to the display settings (Main Menu->Setting->Display) 1 Recording status 3 Video loss 2 Motion detection 4 Camera lock 2.3 Schedule Note: You need to have proper rights to implement the following operations. Please make sure the HDDs have been properly installed. 13

14 After the system booted up, it is in default 24-hour regular mode. You can set record type and time in schedule interface. In the main menu, from Setting to Schedule, you can go to schedule menu. See Figure 2-5. There are total six periods. Channel: Please select the channel number first. You can select all if you want to set for the whole channels. Week day: There are eight options: ranges from Saturday to Sunday and all. Pre-record: System can pre-record the video before the event occurs into the file. The value ranges from 1 to 30 seconds depending on the bit stream. Snapshoot: You can enable this function to snapshoot image when alarm occurs. Record types: There are three types: regular, motion detection (MD) and Alarm. Please highlight icon to select the corresponding function. After completing all the setups please click save button, system goes back to the previous menu. At the bottom of the menu, there are color bars for your reference. Green color stands for regular recording, yellow color stands for motion detection and red color stands for alarm recording. Figure Manual Record Note: Please make sure you have the record operation right and you have properly installed the formatted HDD. You can right click mouse or in the main menu, from Advanced->Manual Record to go to record interface. There are three statuses: schedule/manual/stop. Highlight icon to select corresponding channel. See Figure 2-6. Manual: The highest priority. After manual setup, all selected channels will begin ordinary recording. Schedule: Channel records as you have set in recording setup (Main Menu->Setting- >Schedule) Stop: All channels stop recording. 14

15 Figure Encode Encode interface is shown as in Figure 2-7. Channel: Select the channel you want. Compression: System supports H.264. Resolution: System supports various resolutions, you can select from the dropdown list. For this model, main stream supports D1/CIF/QCIF. Please note the resolution may vary due to different channels. The extra stream supports QCIF only. Frame rate: It ranges from 1f/s to 25f/s in NTSC mode and 1f/s to 30f/s in PAL mode. Note: For the 8-ch series combo DVR, you can refer to the following information. (For the 16-ch series combo DVR, you can also refer to the following information to set the 1-8 channels and the 9-16 channels separately.): If the 1-channel resolution is D1and the frame rate is more than 6f/s, then the rest seven channels (the second channel to the eights channel) resolution shall be CIF or QCIF. If the 1-channel resolution is D1 and the frame rate is or less than 6f/s, then the rest seven channels (the second channel to the eighth channel) resolution shall be D1/CIF/QCIF. Right now in D1 resolution, the max frame rate is 6f/s. Bit rate type: system supports two types: CBR and VBR. In VBR mode, you can set video quality. Quality: There are six levels ranging from 1 to 6. The sixth level has the highest image quality. Video/audio: you can enable or disable the video/audio. Please note the video is enabled for main stream by default. For extra stream, please enable video first and then enable audio. Snapshot: Click snapshot button, you can see it contains the four items: mode/image size/image quality/snapshot frequency. Please refer to chapter for detail information. Please highlight icon to select the corresponding function. Figure

16 2.5.1 Snapshot Schedule Snapshot In Encode interface, click snapshot button to input snapshot mode, size, quality and frequency. In General interface please input upload interval. In Schedule interface, please enable snapshot function. Please refer to the following figure for detail information. See Figure 2-8. Figure Activation Snapshot Please follow the steps listed below to enable the activation snapshot function. After you enabled this function, system can snapshot when the corresponding alarm occurred. In Encode interface, click snapshot button to input snapshot mode, size, quality and frequency. In General interface please input upload interval. In Detect interface please enable snapshot function for specified channels. Or in Alarm interface please enable snapshot function for specified channels. Please refer to the following figure for detail information. See Figure 2-9. Figure Priority Please note the activation snapshot has the higher priority than schedule snapshot. If you have enabled these two types at the same time, system can activate the activation snapshot when alarm occurs, and otherwise system just operates the schedule snapshot Image FTP In Network interface, you can set FTP server information. Please enable FTP function and then click save button. See Figure 2-10.Please refer to the User s Manual included in the resource CD for detailed information. Please boot up corresponding FTP server. Please enable schedule snapshot or activation snapshot (Chapter 2.3.3) and then system can upload the image file to the FTP server. 16

17 Please input the corresponding information here, if you just upload the image FTP. Figure Search and Playback Click search button in the main menu, search interface is shown as below. See Figure Usually there are three file types: R: Regular recording file.- A: External alarm recording file. M: Motion detection recording file Playback control bar Select playback mode here: 4-ch or All-channel Set search setup here :( Time/Channel/Type) Figure 2-11 Please refer to the following sheet for more information. Serial Number Function 1 Play 2 Backward 3 Stop 17

18 4 Slow play 5 Fast play 6 Previous frame 7 Next frame 8 Volume 9 Previous file 10 Next channel 11 Next file 12 Previous channel 13 Search 14 Backup 15 Clip Basic Operation Playback Operation There are various search modes: video type, channel number or time. The system can max display 128 files in one screen. You can use page up/down button to view if there are more than one page. Select the file name and double click mouse (or click enter button), you can view file content Playback Mode There are two playback modes: 4-ch and all-channel. In 4-ch playback mode, you can select the 1/2/3/4-ch playback according to your requirement. In all-channel mode, system can playback in full channels. Please note the 4-ch has no all-channel playback mode Accurate playback Input time (h/m/s) in the time column and then click playback button, system can operate accurate playback Synchronized playback function when playback During playback process, click numeral key, system can switch to the corresponding channel video of the same time Digital zoom When the system is in full-screen playback mode, drag your mouse in the screen to select a section and then left click mouse to realize digital zoom. You can right click mouse to exit File backup and clip System supports backup operation during search. You can draw a before file name (multiple choices). Then click backup button (Button 14 in Figure 2-11). If you want to clip a period of file, please playback the original file first. Click the (Button 15 in Figure 4-10) at the start point (that is your new file beginning point). Drag the file to the end point (that is your new file end point) and then click the button (Button 14 in Figure 4-10) to save your current new file. again. Click the backup Calendar Click calendar icon in Figure 2-11, system pops up a calendar for your reference. The highlighted date means there are record files in that day. You can click blue date to view file list. 18

19 In tx30h30h30the following interface you can see X there are video files in June 13 th and 14 th. Double click the date to view file list. Figure Slow playback and fast playback Please refer to the following sheet for slow play and fast playback function. Button Illustration Remarks Fast play button Slow play button In playback mode, click this button to switch between various fast play modes such as fast play 1,fast play 2 and more. In playback mode, click this button to switch between various slow play modes such as slow play 1 or slow play 2. Frame rate may vary due to different versions. Play/Pause In slow playback mode, click this button to switch between play/pause modes. Previous/next In playback mode, you can click and to view previous or next video in current channel Backward playback and frame by frame playback Button Illustration Remarks Backward play: in playback interface. Manual playback frame by frame. In normal playback mode, left click backward play button, system begins backward playback. Double click backward play button again, system goes to pause mode. Click pause button in normal playback mode, you can use and to view frame by frame. When system is in backward play or frame by frame playback mode, you can click play button / to go to normal playback. Note: All the operations here (such as playback speed, channel, time and progress) have relationship with hardware version. Some series combo DVRs do not support some functions or playback speeds. 2.7 Network Setup Here is for you to input network information. See Figure IP address: Here you can input IP address. DHCP: It is auto search IP function. When enable DHCP function, you can not modify IP/Subnet mask /Gateway. These values are from DHCP function. If you have not enabled DHCP function, IP/Subnet mask/gateway display as o. You need to disable DHCP function 19

20 to view current IP information. Besides, when PPPoE is operating, you can not modify IP/Subnet mask /Gateway. TCP port: Default value is UDP port: Default value is HTTP port: Default value is 80. Max connection: system support maximal 10 users. 0 means there is no connection limit. Transfer mode: Here you can select the priority between fluency/video qualities. Network download: System can process the downloaded data first if you enable this function. Advanced setting: Please refer to the user s manual included in the resource CD for detail information. After completing all the setups please click save button, system goes back to the previous menu. 2.8 Pan/Tilt/Zoom Figure 2-13 Please note: Slight difference may be found in the user s interface, due to various protocols. Please make sure the speed domes A/B cables are properly connected to the A/B ports of combo DVR. You have properly set PTZ information. Please switch camera monitor channel to current window PTZ Setup The pan/tilt/zoom setup includes the following items. Please select channel first. See Figure Protocol: Select corresponding PTZ protocol such as PELCOD. Address: Input corresponding PTZ address. Baud rate: Select baud rate. Data bit: Select data bit. Default value is 8. Stop bit: Select stop bit. Default value is 1. Parity: There are three choices: none/odd/even. Default value is none. 20

21 Figure 2-14 After completing all the setups please click save button, system goes back to the previous menu PTZ Operation In one window display mode, right click mouse (click Fn Button in the front panel or click Fn key in the remote control). The interface is shown as in Figure Figure 2-15 Click Pan/Tilt/Zoom, the interface is shown as below. See Figure Here you can set the following items: Step: value ranges from 1 to 8. Zoom Focus Iris Click icon and to adjust zoom, focus and iris. Figure 2-16 In Figure 2-16, please click direction arrows (See Figure 2-17) to adjust PTZ position. There are total 8 direction arrows. Please note if you use remote control, you can use just four directions (Up/down/left/right). The speed value ranges from 1 to 8. 21

22 Figure D Intelligent Positioning Key In the middle of the eight direction arrows, there is a 3D intelligent positioning key. See Figure Please note, this function needs protocol supported and can only be operated by mouse. Click this key, system goes back to the single screen mode. Drag the mouse in the screen to adjust section size. It can realize PTZ automatically. Figure 2-18 Here is a sheet for you reference. Name Function key function Shortcut key Function key function Shortcut Key Zoom Near Far Focus Near Far Iris close Open You can click set button in Figure 2-16 (or click REC button in the front panel) to set preset, tour, and pattern. You can click page switch button in Figure 2-16 (or click Fn button in the front panel) to call main function. 22

23 3 Web Client Operation Slightly difference may be found in the interface due to different series. 3.1 Network Connection Before web client operation, please check the following items: Network connection is right Combo DVR and PC network setup is right. Please refer to network setup(main menu- >setting->network) Use order ping ***.***.***.***(* combo DVR IP address) to check connection is OK or not. Usually the return TTL value should be less than 255. System can automatically download latest web control and the new version can overwrite the previous one. If you want to un-install the web controls, please run uninstall webrec2.0.bat to auto delete the control or you can go to C:\Program Files\webrec to delete Single folder. 3.2 Login Open IE and input combo DVR address in the address column. For example, if your combo DVR IP is , then please input in IE address column. System pops up warning information to ask you whether install webrec.cab control or not. Please click yes button. If you can t download the ActiveX file, please modify your IE security setup. After installation, the interface is shown as below. See Figure 3-1. Please input your user name and password. Default factory name is admin and password is admin. Note: For security reasons, please modify your password after you first login. Figure Main Window After you logged in, you can see the main window. See Figure 3-2. Click the channel name on the left side; you can view the real-time video. For detailed operation information, please refer to the User s Manual included in the resources CD. 23

24 Figure 3-2 Note For detailed operation introduction, please refer to our resource CD included in your package for electronic version of the User s Manual. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice. If there is any uncertainty or controversy, please refer to the final explanation of ours. Please visit our website for more information. 24