Features Assembly System board for Honeywell Universal Safety IO System board for Honeywell Universal Process IO For 6-channel cards USIO and UPIO For 6 modules Recommended modules: HiC8R (DI), HiC85R (DI), HiC87 (DO), HiC05 (AI), HiC0 (AO) Recommended system cable: CAB-HON-**-S7C-MX- 0000 V DC supply Hazardous area: pluggable screw terminals, blue Non-hazardous area: Sub-D connector (male), 7-pin Function The function of the and the connector pin assignment is exactly fitted to the requirements of Honeywell system. Information about missing supply voltage of the isolated barriers is available for the system as volt-free contact. It is possible to transfer a fault signal to channel of the card via the Loop-in function. The has a robust glass fiber reinforced plastic housing. The is mounted in the switch cabinet on a 5 mm DIN mounting rail according to EN 6075. Connection Release date 08-09- :59 Date of issue 08-09- _eng.xml Zone 0,, Div., TB 5 6 7 8 9 0 CH TB 5 6 X TB TB V DC (I), V DC (II) USIO/UPIO Pepperl+Fuchs Group USA: + 0 86 000 Germany: +9 6 776 Singapore: +65 6779 909
Release date 08-09- :59 Date of issue 08-09- _eng.xml Connection terminal block TB (-, +; -, +) Nominal voltage V DC, in consideration of rated voltage of used isolators Voltage drop 0.9 V, voltage drop across the series diode on the termination board must be considered Ripple 0 % Fusing A Power dissipation 500 mw, without modules Reverse polarity protection yes Redundancy Redundancy available. The supply for the isolators is decoupled, monitored and fused. indication output Output type Contact loading Indicators/settings Display elements volt-free contact 0 V DC, A LEDs PWR ON (power supply) - LED power supply I, green LED - LED power supply II, green LED LED (fault indication), red LED Directive conformity Electromagnetic compatibility Directive 0/0/EU EN 66-:0 (industrial locations) Conformity Electromagnetic compatibility NE :0 For further information see system description. Degree of protection IEC 6059:00 Ambient conditions Ambient temperature -0... 60 C (-... 0 F) Storage temperature -0... 70 C (-0... 58 F) Mechanical specifications Degree of protection IP0 Connection Field side explosion hazardous area: pluggable screw terminals, blue Control side non-explosion hazardous area: 7-pin Sub-D connector pluggable screw terminals, black output pluggable screw terminals, black Core cross-section screw terminals: 0.....5 mm (... AWG) Material housing: polycarbonate Mass approx. 900 g Dimensions 7 x 55 x 5 mm (L x W x H), height including module assembly Mounting on 5 mm DIN mounting rail acc. to EN 6075:00 Data for application in connection with hazardous areas EU-Type Examination Certificate CESI 06 ATEX 0 Marking II ()G [Ex ia Ga] IIC II ()D [Ex ia Da] IIIC I (M) [Ex ia Ma] I Non-hazardous area Maximum safe voltage 50 V (Attention! U m is no rated voltage.) Galvanic isolation Field circuit/control circuit safe electrical isolation acc. to IEC/EN 60079-, voltage peak value 75 V Directive conformity Directive 0//EU EN 60079-0:0+A:0, EN 60079-:0, EN 500:000 International approvals UL approval Control drawing 6-07 IECEx approval IECEx CES 06.000 Approved for [Ex ia Ga] IIC [Ex ia Da] IIIC [Ex ia Ma] I General information Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. Accessories Designation provided accessory: Label Carrier HiALC-HI*TF-SET-** optional accessories: system cable CAB-HON-**-S7C-MX-0000 Pepperl+Fuchs Group USA: + 0 86 000 Germany: +9 6 776 Singapore: +65 6779 909
Application Typical loop Field side Control side Board Loop In function Digital In.5 kω 0 kω - external fault VDC 0 VDC TB TB F F & Digital Out Analog In ma - - - TB V 0 V SL 5a 5b a b Pos. SL 8a a, b a, b V DC Jumper: Loop In function signal X 7 9 7 9 Pepperl+Fuchs system cable HIACA-HW... 7 9-6+ 6- Honeywell USIO/UPIO Pos. 6 TB 9 0 6 SL 5a 5b a b SL 8a a, b a, b V DC Release date 08-09- :59 Date of issue 08-09- _eng.xml HART HART Analog Out P I HART - Pepperl+Fuchs Group USA: + 0 86 000 Germany: +9 6 776 Singapore: +65 6779 909
Pin-out Table Module Channel IS Terminal TB IS terminals SL 5 5 6 6 7 7 8 8 5a 5b a b 5 5a 6 5b 7 a 8 b 9 5a 0 5b a b 5a 5b 5 a 6 b 7 5a 8 5b 9 a 0 b 5a 5b a b 5 5a 6 5b 7 a 8 b 9 5a 0 5b a b Modules Non-IS terminals SL System connector X 8a 7 9 8a 6 8 8a 5 7 8a 6 8a 5 8a 8a 8a 0 Release date 08-09- :59 Date of issue 08-09- _eng.xml Pepperl+Fuchs Group USA: + 0 86 000 Germany: +9 6 776 Singapore: +65 6779 909
Pin-out Table Module Channel IS Terminal TB IS terminals SL 9 9 0 0 5 5 6 6 5a 5b a b 5 5a 6 5b 7 a 8 b 9 5a 0 5b a b 5a 5b 5 a 6 b 7 5a 8 5b 9 a 0 b 5a 5b a b 5 5a 6 5b 7 a 8 b 9 5a 0 5b a b Modules Non-IS terminals SL System connector X 8a 9 8a 8 0 8a 7 9 8a 6 8 8a 5 7 8a 6 8a 5 8a Release date 08-09- :59 Date of issue 08-09- _eng.xml pin out Power supply TB TB Module pin-out (SL): module... 6 a V cc b a b FAULT I - I + II - II + Board fault External fault Pepperl+Fuchs Group USA: + 0 86 000 Germany: +9 6 776 Singapore: +65 6779 909 5