Part no 6159921150 Issue no 04 Date 03/2018 ExBA software A5.7.X User manual Model Part number EABA15-900 6151659610 EABA26-560 6151659620 EABA32-410 6151659630 EABA45-330 6151659640 EABA50-450 6151659650 EABA60-370 6151659660 EABA75-300 6151659670 EABA95-240 6151659680 Model Part number EPBA8-1800-10S 6151659710 EPBA8-1800-4Q 6151659720 EPBA14-900-10S 6151659730 EPBA14-900-4Q 6151659740 EPBA17-700-10S 6151659750 EPBA17-700-4Q 6151659760 Model Part number BLRTA025-2350-10S 6151660230 BLRTA025-2350-4Q 6151660240 Model Part number EABA26-560 QRX 6151660800 EABA32-410 QRX 6151660810 EABA45-330 QRX 6151660820 EABA50-450 QRX 6151660830 EABA60-370 QRX 6151660840 EABA75-300 QRX 6151660850 EABA95-240 QRX 6151660860 www.desouttertools.com
TABLE OF CONTENTS 1 - GETTING STARTED...5 1.1 - Main menu... 5 1.2 - How to unlock the tool menu... 5 2 - TOOL DISPLAY MENU...6 2.1 - Overview... 6 2.2 - How to change the parameters... 7 3 - TOOL PARAMETERS...7 3.1 - Ergostop... 7 3.2 - Sound... 7 3.3 - Torque unit... 7 3.4 - Power saving... 7 4 - PSET PARAMETERS...8 8 - RESULTS MONITORING... 11 9 - RESULTS COLLECTION AND ANALYSIS... 11 10 - MAINTENANCE...12 10.1 - New passwords setting... 12 10.2 - Tool calibration... 12 10.3 - Service alarm... 12 10.4 - Alarm reset... 12 10.5 - Tool information... 12 10.6 - Trouble-shooting... 13 10.7 - Upgrade firmware and tool test... 13 11 - APPENDIX - USER INFO CODES...14 4.1 - List of parameters... 8 4.2 - Motor control... 8 5 - HOW TO PAIR A PSET TO AN ACCESSORY...9 6 - HOW TO RUN THE PSET...10 6.1 - Pset selection... 10 6.2 - Reverse... 10 6.3 - Using icons... 10 7 - TIGHTENING STATUS AND LED REPORTING...10 7.1 - Torque control with angle monitoring... 10 7.2 - Angle control with torque monitoring... 10 Table of contents_03/2018-3 -
- 4 - Table of contents_03/2018
Original instructions Copyright 2018, Ets Georges Renault 44818 St Herblain, FR All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorised parts is not covered by Warranty or Product Liability. 1 - GETTING STARTED This user manual describes how to set up and use the functionalities of the software embedded in the battery nutrunners. Put the tool into service as described in the user manual delivered with the tool or available at https://www.desouttertools.com/resourcecentre. Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. When the tool is powered on, the Desoutter logo is displayed and the LEDs are blinking. Wait for a few seconds while the software is being initialized. 1.1 - Main menu Follow the steps in the chart below to display the different menus and get used to the buttons and icons.... 1.2 - How to unlock the tool menu When delivered, passwords are enabled (1 by default). Passwords are used to protect the Pset and Calibration settings against hazardous changes. The red padlock is displayed on the top line. The first action is to disable the Pset password protection. The process is the same to disable the Maintenance password protection. Configuration Enter pwd. Enter pwd. Pset pwd Enter pwd. Pset pwd 0 Enter pwd. Pset pwd 1 P0 Tool locked Enter pwd. Press for 2 seconds Pset Enter pwd. Pset pwd Configuration Maintenance The password is wrong. Try again The password is correct. Press to quit Each time the battery pack is plugged in, the tool is protected against changes and the red padlock is displayed. 6159921150_04_03/2018-5 -
2 - TOOL DISPLAY MENU 2.1 - Overview Main menu Pset Configuration Maintenance Enable Thread CW/CCW Tightening strategy Target torque/angle Min torque Max torque Min angle Max angle Abort angle/torque Start torque Pulse threshold Angle threshold Rundown speed Downshift torque Final speed Pulse amplitude Ergostop Enable Maximum time QR Acc Pairing Enable Save (only in case of changes) Enter password Pset password Maintenance password Set password Pset password Maintenance password Reverse Enable Alternate Once Sound Sound No sound Torque unit Nm ft.lb in.lb kg.m kg.cm oz.in dnm Power saving Tool Total counter Battery Service alarm Software version Serial number Calibration Calibration Adjust Protected by the Pset password Protected by the Maintenance password - 6-6159921150_04_03/2018
2.2 - How to change the parameters Check that the Pset password is disabled. The green padlock is displayed on the top line. Go to the "Pset" menu and press. Roll the following parameters by using the left and right buttons. Press to validate. To change the parameter, press. The value will switch to orange. Change the values by using left / right buttons and press to validate. Values are coloured in white. When changes are all made in the selected Pset, save the new values. Pressing the trigger at that stage will cancel all modifications done. Go to the screen "" at the end of the Pset parameters list and press. Then use the left / right buttons to select one of the following: Press to save the changes. Press. The parameters are not changed. If no action is done, the display returns to the Pset screen after 15 seconds and the changes will not be saved. 3 - TOOL PARAMETERS 3.1 - Ergostop This function allows a smoother tool stop to reduce the torque reaction on the operator. When delivered, this function is disabled. 3.2 - Sound The "Ergostop" function must be disabled for tightening tests or certification on tightening benches. Voice messages have been created to alert the operator in case of problems or events that may happen during the tightening operation. The voice messages concern the following topics: tightening out of tolerances calibration procedure preventive maintenance low battery hardware failure maintenance When delivered, the function is disabled. 3.3 - Torque unit The sound function is disabled. The sound function is enabled. This function allows to select the torque unit by default. 3.4 - Power saving This function allows to optimize the battery life. Set up the time: none (by default) from 1 to 99 minutes. When the tool is in standby mode, press the reverse button to wake up the tool. 6159921150_04_03/2018-7 -
4 - PSET PARAMETERS There are 6 pre-defined Psets in the tool. The parameters of the Psets are already configured according to the tool characteristics. 4.2 - Motor control (Nm) rpm Rundown speed 4.1 - List of parameters Parameter Description Downshift torque Start torque Downshift speed Time Enable Thread The Pset is enabled. The Pset is disabled. Selection of the thread direction of the screw. When the trigger is pressed, the tool keeps running at Rundown speed. Once Downshift torque has been reached, the speed changes to Downshift speed. CW CCW When operating in forward, the tool rotates clockwise. When operating in forward, the tool rotates counterclockwise. Tightening strategy Target torque Target angle Min./max. torque Min./max. angle Abort angle Abort torque Start torque Torque control with angle monitoring. Angle control with torque monitoring. Torque value to reach. Angle value to reach. Torque values which define the min./max. torque tolerances. Angle values which define the min./max. angle tolerances. Safety angle value to stop the tool. Safety torque value to stop the tool. The "Start torque" is the torque value that must be reached to declare the Pset as started. Below this value, neither result or report will be generated. Angle threshold Rundown speed Downshift torque Final speed Max. time Pulse threshold Pulse amplitude Torque threshold value to start counting angle. Speed applied from start to downshift torque. Torque where speed moves from Rundown to Downshift speed. Speed applied from Downshift torque to motor stop. 30 sec by default. The tools stops when the time is reached. Torque threshold value to switch from continuous mode to pulse mode. (BLRT tools only). Pulse amplitude threshold value in pulse mode. (BLRT tools only). "Ergostop" and "QR Acc pairing" parameters are described in the relevant chapters in this manual. - 8-6159921150_04_03/2018
5 - HOW TO PAIR A PSET TO AN ACCESSORY Plug a battery pack to the tool. This icon lights up green on the QR accessory reader. The tool display is as follows: P0 Plug the accessory into the quick-release output. This icon appears on the top left of the tool display. P0 Go to the tool display and select a Pset. Tick "Pset enabled", change the tightening parameters if needed and tick "QR Acc Pairing". Save the Pset. The tool display is as follows: P1 40.00Nm The tool is ready to run the Pset. This icon lights up green on the QR accessory reader. 6159921150_04_03/2018-9 -
6 - HOW TO RUN THE PSET 6.1 - Pset selection Check that the Pset password is disabled. The green padlock is displayed on the top line. In the Pset menu, check that the Pset is enabled. Press the trigger: the tool will run the Pset. Select another Pset by using the buttons. 6.2 - Reverse When delivered, the "Reverse" function is disabled. Go to the "Configuration" menu and press. Then go to "Reverse" and press. Press again to turn "Enable" orange. Use the right button to enable the function and the left button to disable the function. Press to validate. EAB models only Select "Alternate" or "Once" in the "Configuration/Reverse" menu. alternate once The tool will run in reverse until the operator presses the Reverse button again. The tool will run in reverse once only. To run the tool in reverse again, the operator will have to press the "Reverse" button. To free the assembly, press the "Reverse" button. LEDs will alternatively blink red and green. The tool rotates clockwise or counterclockwise depending on the thread direction already set up in the "Pset" menu. 6.3 - Using icons Press this icon: to validate to wake up the tool to reverse The battery is full The battery is low. 7 - TIGHTENING STATUS AND LED REPORTING The amount of tightenings that can be performed with a fully loaded battery depends on the tool model and application (from 100 to 1,000 tightenings with a 36 V 1.3 Ah battery pack). 7.1 - Torque control with angle monitoring Max torque Target torque Min torque Downshift torque Start torque Examples: (Nm) Angle start Min angle Max angle - Both torque & angle within tolerances will lead to a green LED reporting + backlight. - Torque within tolerances + angle below tolerances will lead to red + yellow status (red backlight). When out of tolerances, a voice message is heard: torque error angle error torque & angle error For high torque tools running in severe applications, it may happen that reports are null when the battery is low. 7.2 - Angle control with torque monitoring ( ) (Nm) This icon and the message Low battery are displayed when the battery is low and a voice message can be heard when the sound function is enabled. The tool cannot perform anymore tightening. Load the battery by using the Desoutter battery charger. Abort torque Max torque Min torque Angle threshold The Pset/Maintenance password is locked. The Pset/Maintenance password is disabled. This icon blinks when the tool memory is full. New results will overwrite the oldest results. Start torque Min angle Target angle Max angle ( ) The accessory has been detected by the QR accessory reader. - 10-6159921150_04_03/2018
8 - RESULTS MONITORING Connect the tool to the PC by using the e-dock device. Launch "CVI MONITOR" to collect and display the last 100 results. Refer to the user manual of "CVI MONITOR" available at http://resource-center.desouttertools. com. 9 - RESULTS COLLECTION AND ANALYSIS CVI ANALYZER is intended to analyse and import/export tightening data with results, curves, filters, profiles. Connect the tool to the PC by using the e-dock device. Launch "CVI ANALYZER". The tool is automatically recognized Refer to the user manual of "CVI ANALYZER" available at http://resource-center.desouttertools. com 6159921150_04_03/2018-11 -
10 - MAINTENANCE 10.1 - New passwords setting Both Pset and Maintenance passwords are set to 1 by default. To set new passwords, current passwords must be disabled and the green padlock displayed. This function is set in the "Configuration" menu: Enter a figure from 0 to 999 for the Pset password. Enter a figure from 0 to 999 for the Maintenance password. Setting the password at 0 will disable all password protections. Save the new password as follows: 10.2 - Tool calibration Press : the password is saved. Press : the password is not saved. The calibration procedure is recommended to compensate for any possible drift of the tool torque or after each change of tool element. This function is set in the "Maintenance" menu. First enter the Maintenance password in the "Configuration" menu. Insert a torque transducer in line with the tool and connect it to any measuring unit from the Desoutter range. Go to the "Maintenance/Calibration" menu. Select the number of tightenings required to execute the calibration and press. Run a tightening Pset the number of times already configured at max. torque and with an angle above 180 (at low speed). 10.3 - Service alarm When a new battery is plugged in, the following may be displayed when service is required: this icon is displayed a service message is displayed (see below) a voice message is heard. Go to "Maintenance" menu and press Go then to "Service alarm" and press When no service is required, "none" is displayed. There are 3 service levels: Level Number of tightenings Service type 1 25,000 calibration 2 250,000 intermediate** 3 500,000 standard ** this type of service is required for heavy duty applications only. Refer to the chapter "Maintenance" in the manual delivered with the tool. 10.4 - Alarm reset Once the service is performed, reset the indicators: Go to the "Maintenance/Service alarm" menu and press. Press to reset the current indicator. Press : indicators will not be reset. 10.5 - Tool information Refer to the "Maintenance" menu (for reading only). If more than 5 tightenings are required, go on with 5 extra tightenings by pressing the trigger. Total counter T Number of tightenings done since the manufacturing of the tool. At the end, the average torque value is displayed in white. On the line below, enter the average torque value measured by the measuring unit (± 20 % vs the tool nominal torque are allowed). Use the left/right buttons to increase or decrease the value. Press and save your data. Battery P Number of pulses done since the manufacturing ot the tool (BLRT tools only). The current voltage value is displayed. Mininimum and maximum voltage values allowed depend on the battery model. Software version AX.YY.ZZ Serial number 17A64685 for example. - 12-6159921150_04_03/2018
10.6 - Trouble-shooting Refer to the Appendix "User info codes" enclosed in this manual. When this icon appears and that the voice message "Hardware failure" is heard at powering on, contact your Desoutter representative for support. 10.7 - Upgrade firmware and tool test These functions are described in the user manual of "CVI MONITOR" software available at https://www. desouttertools.com/resource-centre. 6159921150_04_03/2018-13 -
APPENDIX - USER INFO CODES User info codes are messages displayed on the system or tool display. Information For information only. No action is required. Warning The tool is locked. Tap the message to unlock the tool. Error The tool is locked. The issue has to be solved to unlock the tool and clear the error message. Number Description Procedure I004 Span failure 1- Span value from torque sensor is outside bounds. 2- Try once again to start the tool with no mechanical constraints. If the problem occurs again, contact your Desoutter representative for support. I005 Offset failure 1- Offset value from torque sensor is outside bounds. 2- Try once again to start the tool with no mechanical constraints. If the problem occurs again, contact your Desoutter representative for support. I026 Tool maintenance alarm n1 1- The tool tightening counter has been reached. I027 Tool maintenance alarm n2 1- The tool tightening counter has been reached. I038 Tool logs 1- Unexpected tool software exception. 2- Log file has been generated by the tool. 3- Contact your Desoutter representative for support. I046 Abnormal battery current 1- Abnormal battery current consumption. Check the Pset settings. 2- This error can be due to wrong speed settings. I205 Torque settings 1- Invalid Torque setting: torque is greater than tool characteristics. 2- Check Pset settings with the tool characteristics. I206 Speed settings 1- Invalid speed setting: speed is greater than tool characteristics. 2- Check Pset settings with the tool maximum speed. I210 Invalid Pset selected 1- The selected Pset does not match the Pset selectable in the Assembly Process. I211 Invalid trigger configuration 1- The tool connected to the system is not equipped with the trigger required by the trigger configuration. 2- Adjust your trigger configuration to the tool or change the tool according to the trigger configuration. I224 IGBT too hot 1- Power electronics too warm. 2- Let the system cool down. I251 No Pset selected 1- No Pset selected. 2- Select a Pset. I922 Additional transducer span failure 1- Span value from additional torque sensor is outside bounds. 2- Restart the tool with no mechanical constraints. 3- If the problem occurs again, contact your Desoutter representative for support. W010 Tool calibration expired 1- The tool calibration date has expired. 2- A tool calibration needs to be done to ensure the measurement accuracy. W028 Battery tool version error 1 - Battery tool version and system version are not compatible. W030 The battery is low 1- The battery is low. 2- Recharge the battery. W033 Tool time error 1- The tool time is not set correctly. The tightening results will not be time stamped. 2- Connect the tool to the system to set date and time. W036 Tool memory full 1- The tool memory is full. 2- Connect the tool to the system to empty the memory. W039 Tightening unit configuration error 1- Tightening unit settings are invalid. - 14 - Appendix - User info codes _03/2018
Number Description Procedure W062 Overload of torque 1- Overload of the torque (could be a rehit). 2- Check the tool cable is not damaged. W212 Result not stored 1- It is not possible to store the tightening result in the system. 2- Contact your Desoutter representative for support. W216 Current high 1- Maximum current exceeded. 2- Contact your Desoutter representative for support W267 Result transfer error Result transfer error E007 E008 E009 E012 Motor too hot Tool angle fault Tool invalid parameters Tool EEPROM error 1- Tool is locked because the maximum motor temperature has been reached. 2- Tool will remain locked until the motor temperature comes back to its normal value. 1- Problem detected with the tool angle sensor. 2- The tool needs maintenance. 1- Check the tool compatiblity. 2- The tool memory cannot be read or is invalid. 3- The tool needs maintenance. If the problem occurs again, contact your Desoutter representative for support. 1- The tool memory cannot be read or is invalid. 2- The tool needs maintenance. If the problem occurs again, contact your Desoutter representative for support. E018 Torque out of range! E029 The battery is empty 1- The target torque value is above the tool maximum torque. 2- Check Pset settings with tool characteristics. 1- The battery back is discharged. The tool cannot tighten. 2- Recharge the battery pack. E031 E032 E034 E035 E037 Battery error Tool display error Tool memory error Tool memory locked Tool trigger error 1- Abnormal battery voltage. The tool cannot tighten. 2- Recharge the battery pack. If the problem occurs again, replace the battery pack. 1- Board display malfunction. 2- Contact your Desoutter representative for support. 1- The tool memory does not work properly. 2- Contact your Desoutter representative for support. 1- The tool memory is locked to protect old data from rewriting. 2- Connect the tool to the computer via edock to retrieve old data. 1- The tool trigger does not work properly. 2- Check and clean the trigger. If the problem occurs again, contact your Desoutter representative for support. E045 E047 E048 Abnormal battery voltage Battery is too low Battery type not allowed 1- Check the battery pack. 2- This error can be due to charger malfunction or end of life battery. 1- Check the battery pack. 2- If the problem occurs again, replace the battery pack. 1- Battery type not allowed. 2- Replace the battery pack or your configuration. E223 Drive init error 1- Software failure. 2- Restart the system. 3- If the problem occurs again, contact your Desoutter representative for support. E227 Motor stalled 1- Motor stalled (could be missing phase, wrong motortune or power electronics failure) 2- Try once again. 3- If the problem occurs again, contact your Desoutter representative for support. E228 Drive error 1- Software failure. 2- Restart the system. 3- If the problem occurs again, contact your Desoutter representative for support Appendix - User info codes_03/2018-15 -
More Than Productivity www.desouttertools.com Copyright 2018