SSL 1.1 Series Product Data Sheet REV. 4, 2014 JUN
General Specification Number of Positions Current Rating 2, 4, 6P 3A (Max) Voltage Rating Dielectric Withstand Voltage Durability Color Operating Temperature 100 VAC/VDC (Max) 1200 VAC 100 cycles Natural White Receptacle: -40~+105 C Cable assemblies: -40~+100 C Certifications UL1977, CSA C22.2 No. 182.3, RoHS Material Specification Housing Terminal Thermoplastic, UL94V-0 Copper Alloy, Gold Plated, All over nickel underplated B-to-B, W-to-B, W-to-W Low profile design 2, 4 and 6 pins available SMT Receptacle : Right Angle and Straight types Customized cable length available upon request Single (wire) and dual (flat cable) ended cable assemblies available B2W / B2B locks available for various applications High temperature material for reflow processing Tape & reel packing for high speed SMT processes Cost-effective alternative to hand soldering UL 1977 / Lead Free and RoHS Compliant ** Waterproof receptacle and Field Installable (SSL 1.2) available soon
Physical Dimensions 4.0 6.9 9.9 4.0 6.9 9.9 Reference PCB Design Guideline 2P 4P 6P
Physical Dimensions 7.0 7.0 7.0 4.3 2.9 6.9 2.9 9.9 2.9 Reference PCB Design Guideline 2P 4P 6P
Physical Dimensions 3.3 3.3 3.3 6.0 6.0 6.0 4.3 7.2 10.2 Reference PCB Design Guideline 2P 4P 6P
Physical Dimensions 7.8 11.2 14.2 7.8 11.2 14.2
Current [A] SSL 1.1 Connector Test Characteristics The connector is tested to the following specifications: Mechanical Conditions and Performance Retention Force Durability Connector Mating & Unmating Force Mechanical Shock Vibration Cable Pull-Out Per EIA-364-29, Test Method B, minimum 0.3kgf(2.94N) per contact Per EIA-364-09, mated and unmated connector assemblies for 100 cycles at maximum rate of 500±50 cycles per hour Per EIA-364-13, shall be fully mated at a rate of 25.4 millimeters per minute Mating force 2/4/6P: 0.5/ 1.5/ 2.0kgf maximum Unmating Force / without lock 2/4/6P: 0.1/ 0.4/ 0.5kgf minimum Unmating Force / with lock 2/4/6P: 2.5kgf minimum Per EIA-364-27, Subject mated connector to 50G,half-sine shock pulses of 11 milliseconds duration. Three shocks in each direction applied along 3 mutually perpendicular planes, 18 total shocks. Per EIA-364-28, Test Condition Vll, Subject mated specimens to 3.10G s rms between 20~500HZ. Fifteen minutes in each of 3 mutually perpendicular planes. Per EIA-364-38, apply axial load of 2.0 kgf min. to the cable or wire for one minute. Current-Carrying Capacity Curve Conductor size: 22AWG Ambient Temperature [ C]
Test Characteristics The connector is tested to the following specifications: Electrical Conditions and Performance Low Level Contact Resistance Per EIA-364-23, measure and record the contact resistance with a test current of 100 ma maximum and 20 millivolts open circuit (source) voltage maximum 20 mω maximum initial, 10 mω changes maximum after test Insulation Resistance Per EIA-364-21, apply a test voltage 250V/DC ±10% between the adjacent contacts 1000 МΩ minimum Dielectric Withstand Voltage Temperature Rise Environmental Conditions and Performance Per EIA-364-20, Test Method B, apply a test voltage of 1,200VAC, 60 Hz between adjacent contacts for 1 minute Per UL2238 Section 25, mate connector and measure the temperature rise of contact when the maximum rated T<30 C at 3A Damp Heat, Cyclic Salt Spray Per EIA-364-31, Test method II, Test condition A, 40±2 C at 90% ~ 95% RH, four cycles (4 days) Per EIA-364-26, 5% salt solution for 24 hours unmated Thermal Aging Per EIA-364-17, Method A, Test Condition 4, 105 C for 250 hours Thermal Shock Solderability Resistance to Solder Heat Per EIA-364-32, Method A Test Condition VII. 25 cycles between -40 and 105 C with 30 minute dwells at temperature extremes Per EIA-364-52, Soldering Time : 3s±0.5s, Solder Temperature: 240±2 C 0.2mm from terminal tip 0.2mm from fitting nail tip Solderable area shall have a minimum of 95% solder coverage by 10x magnification. Per EIA-364-56, Procedure 3, Test Condition C, 260±5 C for 10±2 seconds