030-000218 REV F 1114-03F June 29, 2017 Westell Breaker Panel Technical Practice NPDRP1114 FEATURES DIN rail panel accepts up to 6 DIN rail devices (one surge and 5 breakers) Specific configuration of breakers is determined by the user This panel typically operates at output current determined by the breakers installed Single 1.75 mounting height (single panel space) Steel metal chassis. Mounting brackets are supplied for 1 & 1-3/4 spacing and are universal for 19 and 23 racks, with flush mounting options Ground bonding terminations provided that will accept two hole lugs Breakers and surge suppressors are ordered separately UL Recognized
1. GENERAL DESCRIPTION 1.1. The NPDRP1114 Breaker Panel provides up to 5 circuits for the distribution of AC power to equipment. Each of the 5 circuits is protected by a breaker located on the panel's faceplate. The bus is protected by an overvoltage surge protector. The panel is wired in the field by the user for complete flexibility in determining the number of distributions and the number of feeds, within the limit of the 5 breaker positions. 1.2. The power is distributed to the load side equipment through breakers. Each circuit is available for installer connection at the rear of the panel. 1.3. These Breaker Panels are made from steel that s painted off-white. This single rack height panel is shipped with universal brackets (1 & 1-3/4 spacing) that will fit both 19" and 23" wide racks and use only one 1.75" panel space. 2. APPLICATION 2.1. The NPDRP1114 Breaker Panels are designed to be used in the distribution of AC power. They are rack mount panels that can provide AC power to 5 different circuits. Breakers and surge suppressors are ordered separately, consult factory. 2.2 The NPDRP family breaker panels are suitable for installation as part of a Common Bonding Network (CBN, bonded to the equipment rack rails via the rack mounting screws). As well, this family of breaker panels is suitable for restricted access locations in Network Telecommunications Facilities and OSP. 3. INSTALLATION Please read completely before beginning. WARNING: Installation and service should only be performed by an experienced Installer (service person) familiar with AC power distribution systems. An electrician is recommended when working with AC circuits. This equipment is intended to be installed in RESTRICTED ACCESS LOCATIONS by TRAINED SERVICE PERSONNEL ONLY. damage is found, file a claim immediately with the courier, and notify the Customer Service Department. 3.2. Once the panel is unpacked, verify that there are three mounting brackets. The bracket with the vertical slot is used on both 1 and 1-3/4 spacing. There will be two brackets with horizontal slots, these will fit 1 or 1-3/4 spacing. All three brackets are universal for 19 and 23 rack mount spacing (see figure 3.2.1) and can be mounted so the panel can be installed for a flush mounting at front or at rear. Adjust the position and orientation of the correct mounting brackets on the breaker panel, such that it will fit the rack you wish to mount the panel in. 3.3. Mount the panel on the equipment rack using the thread forming #12-24 rack mounting screws and tooth lock washers provided. WARNING: For safety reasons all wiring should be done with the power source removed (when possible). 19" Mounting Position Figure 3.2.1 23" Mounting Position 3.4. CHASSIS GROUND; For safety reasons, the chassis should be electrically connected to the rack ground. From step 3.3. the panel should already be ground to the rack via the #12-24 thread forming rack screws and outside tooth lock washers. In addition to grounding via the mounting brackets, it is recommended you ground the chassis using a ground cable and the two #10 Studs (on 5/8 centers) and locks on back of chassis (#10 bolt torque; 25 IN-LB). Consult your internal practice or local electric code for AWG sizes. Grounding lugs are not included. 3.1. Unpack and inspect the Breaker Panel for possible damage incurred during shipping. If 2
4. SPECIFICATIONS 4.1. Voltage 120 VAC 4.2. Dimensions 1¾ H, 17 W, 3 D (excluding brackets) 4.3. Rack Mounting 19 and 23 Racks for 1 or 1-3/4 Panel Spaces 4.4. Weight Appx 3 Lbs 4.5. Operating Temp. -40 to +65 C (-40 to +149 F) 4.6. Color Off White Compatible Breakers: Square D QOU Series Compatible Surge Suppressors: Transector I 2 R SA-120-50 Series TVS AC Data DRM-120-90 Series 5. TECHNICAL SERVICES 5.1 If technical or customer assistance is required, contact Westell by calling or using one of the following options: Voice: (800) 377-8766 email: global_support@westell.com For additional information about Westell, visit the Westell World Wide Web site at http://www.westell.com. 6. WARRANTY & REPAIRS 6.1 Westell warrants this product to be free of defects at the time of shipment. Westell also warrants this product to be fully functional for the time period specified by the terms and conditions governing the sale of the product. Any attempt to repair or modify the equipment by anyone other than an authorized Westell representative will void the warranty. Ordering Options: NPDRP1114 BR15A240QOU BR30A240QOU BR60A240QOU-2 BRTVS120VAC Blank Din Rail Panel with cover and brackets. Breaker, 15A, 240VAC, 1-Pole Breaker, 30A, 240VAC, 1-Pole Breaker, 60A, 240VAC, 2-Pole Transient voltage suppressor for 120VAC Transient voltage suppressor BRTVS240VAC for 240VAC Additional breaker values are available through Westell or Square D. Contact Technical Services for more information. 6.2 Westell will repair or replace any defective Westell equipment without cost during the warranty period if the unit is defective for any reason other than abuse, improper use, or improper installation. To return defective equipment, first request a Return Material Authorization (RMA) number from Westell by calling or emailing (Customer Service) at the address below. Once an RMA number is obtained, return the defective unit (freight prepaid), along with a brief problem description, to the address we will provide to you when you contact us. email: rgmdept@westell.com Voice: (800) 377-8766 Replacements will be shipped in the fastest manner consistent with the urgency of the situation. Westell will continue to repair or replace faulty equipment beyond the warranty period for a nominal charge. Contact Westell for details. 3
4 Noran Tel
1 2 3 4 5 SURGE PROTECTOR DANGER HIGH VOLTAGE Personnel Only Certified Risk of Electrical Shock Noran Tel 5