Electrical input data minal input voltage 220...240 Vac minal input frequency 47.5...63 Hz minal input current 0.19 minal input power 43 W Power factor 0.96 Total harmonic distortion 10 Efficiency 87, maximum output power minal input voltage DC 0 Vdc minal input current DC 0 Input voltage C 202...254 Vac Performance range Input frequency C 47.5...63 Hz Maximum permissible range Input voltage DC 0 Vdc Maximum permissible range
Electrical output data Regulation method Constant Current Output voltage 33...40 Vdc Output voltage max 55 Vpk Peak voltage at open load Output current 0.94...1.16 Full output current setting Output current tolerance ±8 Output current ripple 30 Ripple = peak / average Output power 36...38 W Full output Galvanic isolation SELV Lamp to mains Electrical data controls input Control method Fixed 0.2...1.5 2 WGO250 (3.5 ), solid wire 16...24 WG WGO250 (3.5 ), solid wire Input wire strip length 8.5...9.5 Output wire cross-section 0.2...1.5 2 WGO250 (3.5 ), solid wire 16...24 WG WGO250 (3.5 ), solid wire Output wire strip length 8.5...9.5 Maximum cable length 80 Wiring Input wire cross-section Total length of wiring including LED module, one way 2013 Koninklijke Philips Electronics N.V. ll rights reserved. Page 2 of 6
Dimensions and weight Length (1) 104 Width (B1) 67.8 Height (C1) 32 Fixing hole diameter (D1) 4 Fixing hole distance (2) 93.5 Weight 144 gram Operational temperatures and humidity mbient temperature +0...+50 Tcase-max 75 Tcase-life 65 Measured at Tc-point Maximum housing temperature 130 In case of a failure Relative humidity 10...90 n-condensing Maximum temperature measured at Tc-point (lifetime reduced by 50) Storage temperature and humidity mbient temperature -25...+85 Relative humidity 5...95 n-condensing Driver lifetime 50,000 30,000 hours Measured temperature at Tc-point is Tcase-life. Lifetime Maximum failures = 10 Remark: this driver is designed to provide a life time of 50K hours at <=55 C <=65 C TC with min. 90 survivals. 2013 Koninklijke Philips Electronics N.V. ll rights reserved. Page 3 of 6
Features Open load protection Yes utomatic recovering Short circuit protection Yes utomatic recovering Over power protection Yes utomatic recovering Hot wiring Suitable for fixtures with protection class I and II Set output current See Design-in guide. Default output current: 1.05 LED module temperature derating Constant Lumen Over Lifetime DC emergency diing Current output decreased to 15 Certificates and standards pproval marks CE/ENEC/C-tick Ingress Protection classification 20 dditional information Inrush current Inrush current Ipeak 18.4 Input voltage 230V Inrush current Twidth 220 µs Input voltage 230V, measured at 50 Ipeak Drivers / MCB 16 type B 28 pcs Earth leakage current 0.7 mpk LED module contribution not included Surge capability (L-N) 1 kv Surge capability (L/N-Ground) 2 kv Earth leakage current Mains input surge capability 2013 Koninklijke Philips Electronics N.V. ll rights reserved. Page 4 of 6
Graphs Operating window Power factor versus output power Efficiency versus output power 2013 Koninklijke Philips Electronics N.V. ll rights reserved. Page 5 of 6
Logistical data Product name Order code Logistic code 12NC 9290 008 83006 EN3 Pieces per box 12 2013 Koninklijke Philips Electronics N.V. ll rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Data subject to change. Date of release: www.philips.com/xitanium