2017 Price List and Specifications Brodart Co. Contract Furniture - Made in USA 280 North Road, Clinton County Industrial Park McElhattan, PA 17748 Toll-Free: 888-521-1884 E-Mail: furniture@brodart.com www.brodartfurniture.com
Specs General Specifications The Brodart power distribution system distributes power from the building s power supply to the furniture through the use of power-distribution channels which may be interconnected to allow multiple pieces to be shared from one power source. The components of the system are as follows: A.) Power entry: Connects the building s power supply and feeds power to the furniture. B.) Power-distribution channel: Houses duplex electrical outlets to access power and serves as a wire management channel. C.) J-channel: An optional wire management tray, which may house data jacks. This channel is necessary when additional storage is required or when data lines are run in addition to electrical cords. POWER-ENTRY ASSEMBLIES Single-circuit power-entry assembly consist of a wood chase that is fastened to the unit with modular fasteners, a PVC plastic liner fastened to the wood chase, and the power-entry cable which is fastened inside of the PVC liner. The power entry cable has a 24 STO cord fitted with a 20-amp plug at the bottom of the assembly and a flexible metal conduit with a quick-connect coupling at the top. This power-entry assembly is used for single-circuit power distribution systems and provides access to circuit #1. The assembly can be plugged into any 20-amp outlet. Multiple-circuit power-entry assembly is to be used if more than one circuit is required. The multiple-circuit power-entry assembly consists of a wood chase that is fastened to the unit with modular fasteners, a PVC plastic liner that is fastened to the wood chase and the power-entry cable which is fastened inside the PVC liner. The bottom of the power-entry has a 72 long liquid-tight conduit. Inside the conduit is an eight-wire harness that is wired to four building circuits: three sharing a common ground and one dedicated with an isolated ground. The top of the power entry consists of a flexible metal conduit and a quick-connect coupling. This power entry is required when more than one circuit or when an isolated with a dedicated ground is required. This assembly must be installed by a qualified licensed electrician. A multiple-circuit system is required under the following conditions: 1.) The length of the wiring served by the power entry exceeds 30 feet. 2.) The total amperage served by the power entry exceeds 20 amps. 3.) A dedicated computer circuit is required. The dedicated computer circuit on system is circuit #4. 4.) More than thirteen (13) duplex receptacles are required. Note: One power-entry assembly is required for each building power source accessed. PANEL-MOUNT, POWER-DISTRIBUTION CHANNEL The panel-mount power-distribution channel is constructed of 20-gauge steel and is finished using a black electrostatically applied epoxy powder paint. The channel is open at the top to allow excess wire to be stored behind the power blocks and the duplex receptacles. Front of the channel has cutouts so two duplex outlets can be mounted. The duplex outlets are rated 15-amps at the receptacle with 20-amps though power. The duplex outlets are connected to each other and the power entry by means of 3/4 flexible metal conduit, which has a quick-connect coupling. The cable consists of an eight-wire, four-circuit system with three standard utility circuits and one isolated circuit with a dedicated ground (computer circuit). If a channel is ordered with one duplex outlet, a plastic cover is provided to cover the unused hole. Units mount to back panels or table keels. 15-AMP POWER-ENTRY LEGS Power-entry legs are to be used with leg-base tables and computer-access stations. Power-entry legs are available in single circuit only. Power-entry legs are finished to match the other legs on the table. Note: 15-amp power legs cannot accept power strips. Receptacles are for electrical device only. WIRE MANAGEMENT LEGS Wire management legs are to be used with leg-base tables and computer-access stations. Wire management legs are finished to match the other legs on the table and allow wires to be run from the floor to the table inconspicuously. ELE 2
Specs Electrical Accessories When ordering duplex receptacles for circuits I, II, III, or IV, the following catalog numbers should be specified. X3 001 S00 Circuit I $65 X3 002 S00 Circuit II $65 X3 003 S00 Circuit III $65 X3 004 S00 Circuit IV (Isolated Circuit) $65 ELE 3
Circulation Desks ELE 4
Circulation Desks Electrical Accessories UL Listed Electric for Circulation Desks, Oak Wood X3 100 S00 Power Entries, All Series, Cord and Plug (Single Circuit) $393 X3 100 S02 Power Entries, All Series, Hardwired (Multiple Circuit) $465 UL Listed Electric for Circulation Desks, Maple Wood X3 100 S00 MAP Power Entries, All Series, Cord and Plug (Single Circuit) $393 X3 100 S02 MAP Power Entries, All Series, Hardwired (Multiple Circuit) $465 Note: Grommets are not always included on product as a standard item. If wires are to be passed through the work surface or from one unit to another, grommets may need to be ordered separately. Power Distribution Channels for Circulation Desks, All Series One Duplex Outlet Channel X3 012 S02 Circ Desk, One Outlet Channel, SW Unit $486 X3 017 S02 Circ Desk, One Outlet Channel, Multipurpose Corner $825 X3 032 S02 Circ Desk, One Outlet Channel, ADA Unit $605 X3 040 S02 Circ Desk, One Outlet Channel, 90 Curved Corner $572 Two Duplex Outlet Channel X3 011 S00 Circ Desk, Two Outlet Channel, DW Unit $608 X3 012 S00 Circ Desk, Two Outlet Channel, SW Unit $576 X3 017 S00 Circ Desk, Two Outlet Channel, Multipurpose Corner $906 X3 032 S00 Circ Desk, Two Outlet Channel, ADA Unit $625 X3 040 S00 Circ Desk, Two Outlet Channel, 90 Curved Corner $608 X3 047 S00 Circ Desk, Two Outlet Channel, 60 g Nu-Curve Desk $689 Bypass Channels X3 311 S00 Circ Desk, Bypass Channel, DW Unit $573 X3 312 S00 Circ Desk, Bypass Channel, SW Unit $447 X3 316 S00 Circ Desk, Bypass Channel, 90 Closed Corner $441 X3 317 S00 Circ Desk, Bypass Channel, Multipurpose Corner $575 X3 318 S00 Circ Desk, Bypass Channel, 45 Closed Corner $441 X3 332 S00 Circ Desk, Bypass Channel, ADA Unit $477 X3 340 S00 Circ Desk, Bypass Channel, 90 Curved Corner $579 X3 347 S00 Circ Desk, Bypass Channel, 60 Nu-Curve Desk $572 Note: This asssembly is for units that do not require electrical access but need to have power passed through to the adjoining units. Unit does not include any duplex outlets. ELE 5
Media Stations & Carrels ELE 6
Media Stations & Carrels Electrical Accessories Power Entries for Modular Media Stations, Oak Wood X3 300 S00 Power Entry, Cord and Plug (Single Circuit) $385 X3 300 S02 Power Entry, Hardwired (Multiple Circuit) $458 Power Entries for Modular Media Stations, Maple Wood X3 300 S00 MAP Power Entry, Cord and Plug (Single Circuit) $385 X3 300 S02 MAP Power Entry, Hardwired (Multiple Circuit) $458 Note: Grommets are not always included on product as a standard item. If wires are to be passed through the work surface or from one unit to another, grommets may need to be ordered separately. Power Distribution Channels for Modular Media Stations One Duplex Outlet X3 354 S00 36" Wide Position $349 X3 454 S00 48" Wide Position $377 X3 554 S00 Functional Corner Unit $533 Note: This asssembly is for units that do not require electrical access but need to have power passed through to the adjoining units. Power Entries for Panel Based Carrels, Oak Wood Chase X3 100 S00 Power Entries, All Series, Cord and Plug (Single Circuit) $393 X3 100 S02 Power Entries, All Series, Hardwired (Multiple Circuit) $465 Power Entries for Panel Based Carrels, Maple Wood Chase X3 100 S00 MAP Power Entries, All Series, Cord and Plug (Single Circuit) $393 X3 100 S02 MAP Power Entries, All Series, Hardwired (Multiple Circuit) $465 Power Entries for Panel and Post Furniture, Oak Wood Chase X3 101 S00 Power Entries, All Series, Cord and Plug (Single Circuit) $393 X3 101 S02 Power Entries, All Series, Hardwired (Multiple Circuit) $465 Power Entries for Panel and Post Furniture, Maple Wood Chase X3 101 S00 MAP Power Entries, All Series, Cord and Plug (Single Circuit) $393 X3 101 S02 MAP Power Entries, All Series, Hardwired (Multiple Circuit) $465 Power Distribution Channels for Carrels One Duplex Outlet X3 673 S02 36" Wide Position $486 X3 460 S02 48" Wide Position $501 Two Duplex Outlet X3 673 S00 36" Wide Position $569 X3 460 S00 48" Wide Position $595 Note: Grommets are not always included on product as a standard item. If wires are to be passed through the work surface or from one unit to another, grommets may need to be ordered separately. ELE 7
15-Amp Legs Quorum 94 Series Plate Style, 15-Amp Power-Outlet Leg, Oak Wood Veneer X1 941 S00 Leg & Plate Type for 29"H Table $597 X1 941 S02 Leg & Plate Type for 27-1/2"H Table $593 X1 941 S03 Leg & Plate Type for 25"H Table $582 X1 941 S04 Leg & Plate Type for 32"H Table $638 Quorum 94 Series Plate Style, 15-Amp Power-Outlet Leg, Maple Wood Veneer X1 941 S00 MAP Leg & Plate Type for 29"H Table $650 X1 941 S02 MAP Leg & Plate Type for 27-1/2"H Table $646 X1 941 S03 MAP Leg & Plate Type for 25"H Table $634 X1 941 S04 MAP Leg & Plate Type for 32"H Table $695 Quorum 94 Series Apron Style, 15-Amp Power-Outlet Leg, Oak Wood Veneer X1 942 S00 Leg & Apron Type for 29"H Table $556 X1 942 S04 Leg & Apron Type for 32"H Table $596 X1 942 S05 Leg & Apron Type for 39"H Table $636 Quorum 94 Series Apron Style, 15-Amp Power-Outlet Leg, Maple Wood Veneer X1 942 S00 MAP Leg & Apron Type for 29"H Table $606 X1 942 S04 MAP Leg & Apron Type for 32"H Table $649 X1 942 S05 MAP Leg & Apron Type for 39"H Table $693 Leg is 2-1/4" square, 1/8" thick wall, aluminum extrusion with 3/4" radius on the outside corners. Leg is oak beneer wrapped to match other legs on the table and has three receptacles for power outlet and a 2' SJT power cord. A Hi-Pot Test of insulation and connections of 1,200 volts is given to each leg. Note: The use of grommets for wire passage through the work surface is recommended. 15-amp power legs cannot accept power strips. Receptacles are for electrical device only. ELE 8
Wire Management Legs Electrical Accessories Chancellor's Series Wire Management Leg Round Leg Style X3 CHR6 S00 Leg & Apron Type for 29"H Table $287 X3 CHR6 S02 Leg & Apron Type for 27-1/2"H Table $287 X3 CHR6 S03 Leg & Apron Type for 25"H Table $287 X3 CHR6 S04 Leg & Apron Type for 32"H Table $287 Square Leg Style X3 CH25 S00 Leg & Plate Type for 29"H Table $287 X3 CH25 S02 Leg & Plate Type for 27-1/2"H Table $287 X3 CH26 S05 Leg & Apron Type for 39"H Table $287 Leg is constructed according to standard Chancellor Series Leg construction. Leg is slotted 4" from the top and 2-1/2" from the bottom with a 1/2" W slot. Slots receive a snap-on metal cover, which allows a 1" opening at the top and bottom of the slot for cord exit. Slot accepts two 3/8" power cords or four data cables. Epoch Series Wire Management Leg Powder-Coated Leg Style 59 945 S00 Powder-Coated Leg for 29"H Table $331 59 945 S02 Powder-Coated Leg for 27-1/2"H Table $332 59 945 S03 Powder-Coated Leg for 25"H Table $331 Powder-Coated Chrome Leg Style 59C 945 S00 Chrome Leg for 29"H Table $655 59C 945 S02 Chrome Leg for 27-1/2"H Table $643 59C 945 S03 Chrome Leg for 25"H Table $643 Oak Wood Leg Style 59W 945 S00 Wood Leg for 29"H Table $388 59W 945 S02 Wood Leg for 27-1/2"H Table $388 59W 945 S03 Wood Leg for 25"H Table $388 Chrome Maple Wood Leg Style 59W 945 S00 MAP Wood Leg for 29"H Table $388 59W 945 S02 MAP Wood Leg for 27-1/2"H Table $388 59W 945 S03 MAP Wood Leg for 25"H Table $388 Leg is constructed according to standard Epoch leg construction. The leg will receive a 3/4" wide slot located in the back of the leg underneath the angle bracket, 6-5/16 down from the top of the leg and 2-1/4" from the bottom of the leg. A spring loaded cover of 1/8" bent metal will provide access and storage of electrical cords. The spring loaded cover will provide a 1"D egress at the top and bottom of the slot for cords. The leg is powder coated, chromed, or wraped in wood veneer according to the product specified. Wood ELE 9
Wire Management Legs Quorum 94 Series Wire Management Leg X3 945 S00 Leg & Plate Type for 29"H Table $267 X3 945 S02 Leg & Plate Type for 27-1/2"H Table $267 X3 945 S03 Leg & Plate Type for 25"H Table $267 X3 945 S04 Leg & Plate Type for 32"H Table $267 X3 946 S00 Leg & Apron Type for 29"H Table $267 X3 946 S04 Leg & Apron Type for 32"H Table $267 X3 946 S05 Leg & Apron Type for 39"H Table $267 Leg is constructed according to standard Quorum 94T Leg construction. Leg is slotted 4" from the top and 2-1/2" from the bottom with a 1/2" W slot. Slots receive a snap-on veneer wrapped cover, which allows a 1" opening at the top and bottom of the slot for cord exit. Slot accepts two 3/8" power cords or four data cables. ELE 10
Accessories Electrical Accessories Duplex Outlet Receptacles X3 001 S00 Circuit I $65 X3 002 S00 Circuit II $65 X3 003 S00 Circuit III $65 X3 004 S00 Circuit IV (Isolated Circuit) $65 Circuit I receptacles are supplied as standard. When ordering duplex receptacles for circuits II, III or IV, the following numbers should be specified. Data/Communication Terminal & Jacks X3 005 S00 RJ11 Telephone Jack $37 X3 007 S00 RJ45 Category Five Data Jack $40 X3 007 S02 RJ45 Category Five Data Jack w/9 ft Patch Cord $65 X3 007 S03 RJ45 Category Five Data Jack w/12 ft Patch Cord $69 Note: Data jacks are wired for TIA/EIA T568A. Horizontal Surface-Mount Data Outlet Box without Data Jacks & Cables X1 700 074 Horizontal Data Outlet Box $66 Constructed of black ABS plastic, box is designed for use in the horizontal mounting of data. This box inter-members with the X1 700 065 and X1 700 066 raceways. Capacity of two jacks. Note: Data jacks not included. Vertical Date Outlet Box without Data Jacks X1 700 070 Vertical Data Outlet Box $99 Constructed of black ABS plastic, box is designed for use in the vertical mounting of data. This box inter-members with the X1 700 065 and X1 700 066 raceways. Capacity of two jacks. Note: Data jacks not included. Power Strips X1 700 112 Power Strip, 3 Outlet Power Strip with a 9' SJT Cord $65 73 200 S00 Electrical Interport w/2 outlets & 2 ports for data (purchase data separately) $267 73 258 S00 15-amp Power/Data Strip $305 This unit consists of an outlet strip with four surge-protected electrical outlets and two RJ45 category 5 data jacks. Unit has two 9' patch cords for data and a 9' power cord. Unit has a resettable circuit breaker. Note: Grommets are not always included on product as a standard item. If wires are to be passed through the work surface or from one unit to another, grommets may need to be ordered separately. ELE 11
Accessories Tabletop/Worksurface Distribution Corner Mounted Power/Communication Center 73 560 S00 Corner Power Unit $258 Constructed of black ABS plastic, the unit has four electrical outlets; three above the work surface, one below. The unit mounts in the corner of a carrel or PAC station. Unit comes with a nine foot SJT power cord. 73 559 S00 Corner Power and Communication Center without Patch Cords $436 73 559 S02 Corner Power and Communication Center with 9' Patch Cords $473 Constructed of black ABS plastic, the unit has four electrical outlets; three above the work surface, one below. Unit also has a data module which allows for up to three data jacks. Unit comes standard with two RJ45 Category 5 data jacks. The unit mounts in the corner of a carrel or PAC station. Unit comes with a nine foot SJT power cord and can be ordered with or without nine foot data patch cords. Note: Data jacks are wired for TIA/EIA T568A. Tabletop/Worksurface Distribution OPAC Station Power Assembly 73 274 S00 Panel Power Assembly for 3-, 4- and 6-Position PAC Station $895 Overall dimensions: 14"H x 27-1/2"W x 2"D Power assembly panel is constructed of 3/4" veneered particleboard with 2-1/2"D cleats on the end for mounting to the PAC unit. The assembly is installed in the well created in the center of the PAC stations. The power assembly has two six-outlet, 15-amp power strips. Each outlet strip has a 9' SJT power cord. Space is available on the panel for future data patch panel requirements. Note: Outlets are for electrical devices only and are not for plugging in power strips. Tabletop/Worksurface Distribution Panel Table Power and Data Outlet 73 280 S00 Panel Mounted Power and Data Outlet $589 Overall dimensions: 2-3/4" x 8-1/2" x 3-3/8"D Unit is constructed using the same species of wood and the same finish as the unit on which it is mounted. The unit has three 15-amp electrical outlets with resettable circuit breaker and is provided with a 9' SJT cord and two RJ45 category 5 data jacks with nine foot patch cords.. Note: Outlets are for electrical devices only and are not for plugging in power strips. ELE 12
Accessories Electrical Accessories Tabletop/Worksurface Distribution Single-Faced Tilt Up Power and Data Center 73 268 S00 S/F Tilt Up Power and Data Center $572 Overall dimensions: 10"W x 5-3/4"D Tilt up data and power center is constructed from 18-gauge steel painted black. The unit has three electrical outlets with resettable circuit breaker and comes standard with two RJ45 category 5 data jacks with 9' patch cords and a 9' SJT cord. The access door is spring loaded and opens to an approximate 42 angle. The access door is held closed with a spring-loaded clasp. Unit mounts into the tabletop. Door opening is 4-1/4"D x 8-3/8"W. Tabletop/Worksurface Distribution Double-Faced Tilt Up Power and Data Center 73 368 S00 D/F Tilt Up Power and Data Center $1,195 Overall dimensions: 10"W x 10-3/4"D Tilt up data and power center is constructed from 18-gauge steel painted black. The unit has six electrical outlets with resettable circuit breaker and comes standard with four RJ45 category 5 data jacks with 9' patch cords and two 9' SJT cords. The access doors are spring loaded and open to an approximate 42 angle. The access door is held closed with a spring-loaded clasp. Unit mounts into the tabletop. Door opening is 4-1/4"D x 8-3/8"W. Tabletop/Worksurface Distribution Table Power Tap, Round Note: Data jacks are wired for TIA/EIA T568A. For factory cutout to install the unit, a sketch must be provided to show the unit in the work surface with dimensions noting the exact location. XSU PT4RD S Table Power Tap, Round $298 Unit is designed to allow hidden power and data access in a work surface. Constructed of black ABS plastic, the unit contains three (3) 15-amp outlets and two (2) Cat 5 Ethernet connections. Power cord is 8' in length. Unit fits into a 4-7/32" diameter hole and overall dimension is 4-3/8" diameter. Note: For factory cutout to install the unit, a sketch must be provided to show the unit in the work surface with dimensions noting the exact location. Power Sphere (Fits into Standard 3" Grommet Hole) Two Outlets per sphere - 8 spheres can be linked off one plug (in sequential order) XBE01640L1 S Power Sphere Starter, Link 1, 10' Cord & Plug $312 XBE01640L2 S Power Sphere Adder, Link 2, 5' Cord (Black/Red) $239 XBE01640L3 S Power Sphere Adder, Link 3, 5' Cord (Red/Blue) $239 XBE01640L4 S Power Sphere Adder, Link 4, 5' Cord (Blue/Orange) $239 XBE01640L5 S Power Sphere Adder, Link 5, 5' Cord (Orange/Yellow) $239 XBE01640L6 S Power Sphere Adder, Link 6, 5' Cord (Yellow/Green) $239 XBE01640L7 S Power Sphere Adder, Link 7, 5' Cord (Green/White) $239 XBE01640L8 S Power Sphere Adder, Link 8, 5' Cord (White) $239 Unit is designed to fit into a standard 3" grommet hole. This 15A system can link up to 8 duplex devices (must be connected in sequence). Each module contains two outlets. Note: For factory cutout to install the unit, a sketch must be provided to show the unit in the work surface with dimensions noting the exact location. ELE 13
Grommets & Wire Managers General Specifications Have electrical power and data access conveniently located; where you need it and in the format required by your computer system and all other electrically powered equipment. Prevent wire clutter by storing excess cables and wires in wire-management channels. Based upon your specification, Brodart provides single or multi-circuit power systems with optional dedicated computer circuitry. Also, a choice of 15-amp or 20-amp systems, as you specify. Quick-connect cable couplings are utilized by Brodart to permit easy, on-site installations and to provide for rearrangement as changing needs dictate. NOTES: Grommets are not always included as standard with the product. If wires are to be passed though work surfaces or from one unit to another you will need to order the grommets separately. For factory-cut holes to install grommets, a sketch must be provided to show the unit in the work surface with dimensions noting the exact location. Grommet with Cap, 2" Round X1 700 001 Grommet with Cap, 2" Round $64 Constructed Black of ABS plastic, 2" round grommet fits 1-3/4" diameter hole. Nominal 1-5/8" inside diameter. Includes notched 5/8" W removable cap. Grommet with Cap, 3-1/2" Round X1 700 002 Grommet with Cap, 3-1/2" Round $72 Constructed Black of ABS plastic, 3-1/2" round grommet fits 3" diameter hole. Nominal 2-7/8" inside diameter. Includes notched 5/8" W removable cap. Grommet with Paper Slot, 17" Long X1 700 111 Grommet with Paper Slot, 17" Long $151 Constructed Black of ABS plastic. Inside dimensions are 17" x 1". ELE 14
Grommets & Wire Managers Electrical Accessories Plastic J-Channel Wire Manager X1 700 020 Plastic J-Channel Wire Manager $86 Constructed of dark brown ABS plastic. Designed to be mounted by screwing or stapling to most surfaces. Front "J" is flexible for inserting cords. Inside dimensions: 1-1/2"H x 1"W x 72"L Data and Communication Raceway, 1/2"H x 1"W x 6'L X1 700 065 Data and Communication Raceway, 1/2"H x 1"W x 6'L $107 One-piece, black, latching surface raceway for low voltage communications cabling applications. Supplied with preapplied adhesive-backed tape for trouble-free and permanent mounting. Will hold up to four data cables. Can be used with category 5 and fiber optic cabling applications. Power Data Raceway, 7/8"H x 1-1/2"W x 10'L X1 700 066 Power Data Raceway, 7/8"H x 1-1/2"W x 10'L $164 One-piece, brown, latching surface raceway for data, voice, video, fiber optic and power cabling applications. Unit has two channels that can route both power and data. Supplied with preapplied adhesive-backed tape for trouble-free and permanent mounting. Unit requires screw mounting when using for power applications. Wire Manager For Table Mounting X1 700 030 22" J-Channel, 3-1/2"H x 22"W x 3-1/4"D $72 X1 700 031 28" J-Channel, 3-1/2"H x 28"W x 3-1/4"D $92 Designed for electrical or data cables, unit is constructed of 18-gauge steel with electrostatically applied black powder-paint. Designed to be mounted to the underside of a tabletop. Note: Grommets are not always included on product as a standard item. If wires are to be passed through the work surface or from one unit to another, grommets may need to be ordered separately. Wire Manager For Panel Mounting XJ 012 S00 30" J-Channel, 3-1/8"H x 30"W x 4"D $145 XJ 673 S00 32" J-Channel, 3-1/8"H x 32"W x 4"D $145 XJ 047 S00 38" J-Channel, 3-1/8"H x 38"W x 4"D $164 XJ 460 S00 44" J-Channel, 3-1/8"H x 44"W x 4"D $175 Designed for electrical or data cables, unit is constructed of 18-gauge steel with electrostatically applied black powder-paint. The front lip of the panel is 2"H. Unit mounts to back panels or keels. Note: Grommets are not always included on product as a standard item. If wires are to be passed through the work surface or from one unit to another, grommets may need to be ordered separately. Modular insert data jacks sold separately. ELE 15
Grommets & Wire Managers Vertical Wire Chase, Oak Wood X1 700 195 Wood Wire Chase for 25"H Work Surface, Actual height 22" $164 X1 700 197 Wood Wire Chase for 29"H Work Surface, Actual height 26" $205 X1 700 199 Wood Wire Chase for 39"H Work Surface, Actual height 36" $223 Vertical Wire Chase, Maple Wood X1 700 195 MAP Wood Wire Chase for 25"H Work Surface, Actual height 22" $164 X1 700 197 MAP Wood Wire Chase for 29"H Work Surface, Actual height 26" $205 X1 700 199 MAP Wood Wire Chase for 39"H Work Surface, Actual height 36" $223 Designed to manage cords below the work surface, unit is constructed the wood species specified and finished to match. Inside Dimensions are 2-1/4" x 3" Flexible Wire Management Channels (Leg Style) 73 210 S00 32" for Sitting Height Tables $329 73 210 S01 39" for Standing Height Tables $362 Metal Vertical Wire Manager X1 700 050 Vertical Wire Manager for Table Mounting $254 Designed to be mounted underneath the work surface below a grommet. Unit is constructed of a 3-1/2" diameter steel tube and finished with black electrostatically applied powder paint. ELE 16 F11-1-17A-ELE