Laboratory automation

Siemens AG 2008 Laboratory automation /2 SIMATIC PCS 7 LAB: Compact control system for the laboratory automation Siemens ST PCS 7.1 Update October 2008

Laboratory automation Siemens AG 2008 Overview PCS 7 Add-on fit for SIMATIC PCS 7 V7 The following module combinations are offered as standard configurations: SIMATIC PCS 7 LAB ET 200M, consisting of PC module and ET 200M I/O module SIMATIC PCS 7 LAB ET 200pro, consisting of PC module, ET 200pro I/O module and POWER module These can also be expanded by the optional SER module. Further configurations and solutions are also possible. If your requirements cannot be solved using the standard configurations offered, please contact the address specified in the section "Further information" to obtain an alternative offer. PC module One feature of laboratory work is the frequent modification of experiments through which valuable knowledge, data and parameters are gained for series production. Particularly essential for automation of the laboratory - in addition to high quality, efficiency and safety - is therefore fast and flexible adaptation of the laboratory equipment to the automation technology. The simple and universal SIMATIC PCS 7 LAB is explicitly tailored to these specific requirements. Ready-to-use solution proposals for typical laboratory applications, e.g. for dosing, temperature control or inertization processes, significantly assist the laboratory personnel in their work with the integrated control technology. SIMATIC PCS 7 LAB not only allows autonomous automation of the laboratory. Integration in a SIMATIC PCS 7 plant network permits both efficient exchange of information and simple transfer of laboratory results to the production department. Design The basic components for configuration of a SIMATIC PCS 7 LAB are five rugged modules which can be integrated into any laboratory as a result of their compact design: PC module ET 200M I/O module ET 200pro I/O module POWER module for ET 200pro SER module It is then possible to implement an extremely flexible centralized or distributed design in various environments. Mobile use at changing locations is also possible. The PC module provides the functionalities for automation, engineering and HMI. It is technically comparable with the integral SIMATIC PCS 7 BOX 416 (see Catalog ST PCS 7, section "Starter systems, SIMATIC PCS 7 BOX"). On the front there are: 2 Industrial Ethernet connections 2 PROFIBUS DP connections 4 USB interfaces (2 x high current, 2 x for mouse and keyboard) 1 serial COM1 interface A DVI-I interface at the rear permits the connection of a suitable monitor (not included in the scope of supply). A monitor with VGA interface can also be connected via an adapter. Also at the rear are 2 ECOFAST interfaces for the PROFIBUS DP connection of the I/O modules and the SER module. The SIMATIC PCS 7 engineering software AS/OS, including 250 PO AS/OS runtime license for productive operation, is preinstalled on the PC module. This can be extended by SIMATIC BATCH and SIMATIC Route Control functionalities. /2 Siemens ST PCS 7.1 Update October 2008

Siemens AG 2008 Laboratory automation I/O modules Depending on the environment of use and the technical conditions, you can choose between two preconfigured I/O modules with selected modules from the ET 200M or ET 200pro distributed I/O systems. ET 200M I/O module The following components are mounted side by side on the module carrier: IM 154-2 High Feature PROFIBUS DP interface 7 ET 200M I/O modules from the following range: - EM 144 analog input module for current measurements: AI I 4 x +/-20 ma - EM 144 analog input module for voltage measurements: AI U 4 x +/- V - EM 144 analog input module for temperature measurements: AI RTD 4 x Pt0 - EM 145 analog output module: AO I 4 x +/-20 ma - EM 141 digital input module: DI 8 x 24 V DC - 2 x EM 142 digital output module: DO 4 x 24 V DC/2 A Actuators and sensors are connected via 5--pole M12 plugs to the connection modules of the electronic modules. POWER module for ET 200pro The ET 200M I/O module contains the following components: 0... 240 V AC/24 V DC power supply ( A) IM 153-2 High Feature PROFIBUS DP interface CP341 serial interface module (2 x RS 232C) 6 ET 200M I/O modules from the following range: - SM 331 analog input module for current measurements: AI I 8 x 0/4... 20 ma - SM 331 analog input module for voltage measurements: AI U 8 x ± V - SM 331 analog input module for temperature measurements: AI RTD 4 x Pt0 - SM 332 analog output module: AO I 8 x 0/4... 20 ma - SM 321 digital input module: DI 16 x 24 V DC - SM 322 digital output module: DO 16 x 24 V DC/0.5 A The I/O modules are wired on the front panels using color-coded safety laboratory sockets (4 mm) for DI, DO, AI, AO and functional ground. These plug connections allow fast and flexible connection to sensors and actuators, and are extremely advantageous when frequent modification or conversion is necessary. The two serial interfaces of the CP341 are connected to two 9-pole sub-d connectors. ET 200pro I/O module The POWER module is used for the external 24 V DC supply of the ET 200pro I/O module. The 24 V DC infeed is via the ECOFAST hybrid cable of the PROFIBUS DP. The PROFIBUS DP is looped through on the POWER module. SER module The ET 200pro I/O module with high IP65 degree of protection can be installed directly in the laboratory equipment. The SER module is equipped with four CP 341 and provides a total of 8 serial RS 232C interfaces for connecting external devices. These interfaces are connected to 9-pole sub-d connectors arranged in pairs on the front of the module. Siemens ST PCS 7.1 Update October 2008 /3

Laboratory automation Siemens AG 2008 Function Selection and Ordering Data An example project including hardware and bus configurations SIMATIC PCS 7 LAB ET 200M is installed on the SIMATIC PCS 7 LAB. This can be used for acquaintance purposes and to test the inputs and outputs. The Compact process control system for laboratory automation, without monitor; hardware and bus configurations can be used as the basis for operating system and SIMATIC own applications. PCS 7 software preinstalled Software equipment modules are additionally available free of Type of delivery: charge for the following laboratory-specific applications: 1 x PC module Agitation (stirring) 1 x ET 200M I/O module Pressure (aerating and venting) 1 x mouse (USB) 1 x keyboard (USB) Discharge (delivery/transfer) 2 x power cable "Europe" Dosing by means of a modulating valve 1 x backup battery for WinAC Analysis Slot 416 Temperature (temperature adjustment) 2 x ECOFAST cable, m 2 x ECOFAST bus termination Dosing of solids connector Dosing with open/closed valve 1 x restore DVD and license for Microsoft Windows XP Please contact: Professional Siemens AG 1 x SIMATIC PCS 7 engineering I IA CC CCG software for AS/OS, including Siemensallee 84 250 PO AS/OS runtime license for productive operation, floating 76187 Karlsruhe license for 1 user Germany 1 x license for SIMATIC PCS 7 SFC Visualization, Technical specifications floating license for 1 user 1 x CD with software and documentation for WinAC SIMATIC PCS 7 LAB Dimensions Weight Degree of modules (WxHxD) in mm in kg protection Slot 412/416 1 x CD for CP 341 1 x documentation for SIMATIC PCS 7 LAB and SIMATIC Box PC 627B PC module 585 x 300 x 332 21 IP20 I/O module ET 200M 585 x 300 x 332 19 IP20 I/O module ET 200pro 500 x 180 x 85 5,5 IP65 POWER module for 370 x 300 x 316 12 IP20 ET 200pro SER module 585 x 300 x 332 19 IP20 SIMATIC PCS 7 LAB ET 200pro Compact process control system for laboratory automation, without monitor; operating system and SIMATIC PCS 7 software preinstalled Type of delivery: 1 x PC module 1 x ET 200pro I/O module 1 x POWER module 1 x mouse (USB) 1 x keyboard (USB) 1 x backup battery for WinAC Slot 416 1 x ECOFAST cable, m 1 x ECOFAST cable, 5 m 2 x ECOFAST bus termination connector 2 x power cable "Europe" 1 x restore DVD and license for Microsoft Windows XP Professional 1 x SIMATIC PCS 7 engineering software for AS/OS, including 250 PO AS/OS runtime license for productive operation, floating license for 1 user 1 x license for SIMATIC PCS 7 SFC Visualization, floating license for 1 user 1 x CD with software and documentation for WinAC Slot 412/416 1 x documentation for SIMATIC PCS 7 LAB and SIMATIC Box PC 627B Order No. 6DL3 902-1BA00 6DL3 902-2BA00 /4 Siemens ST PCS 7.1 Update October 2008

Siemens AG 2008 Laboratory automation Selection and Ordering Data Order No. More information Option SER module for SIMATIC PCS 7 LAB Module with eight RS 232C serial interfaces for connection of external devices Type of delivery: 1 x SER module 1 x power cable "Europe" 1 x ECOFAST cable, m 1 x ECOFAST bus termination connector 1 x CD for CP 341 Accessories 6DL4 903-1AA Siemens AG Industry Sector Industry Automation Karlsruhe, Germany Phone: +49 721 595-3776 Fax: +49 721 595-4711 E-mail: addon_s2.aud@siemens.com Additional information is available in the Internet under: http://www.siemens.com/simatic-pcs7-lab Power cable, 3 m For Great Britain 6ES7 900-0BA00-0XA0 For Switzerland 6ES7 900-0CA00-0XA0 For the USA 6ES7 900-0DA00-0XA0 For Italy 6ES7 900-0EA00-0XA0 For China 6ES7 900-0FA00-0XA0 Notes: SIMATIC PCS 7 LAB is based on the software of the current SIMATIC PCS 7 V7 process control system. SIMATIC PCS 7 LAB can be extended by supplementary and expansion components for the SIMATIC PCS 7 BOX 416 (see Catalog ST PCS 7, section "Starter systems, SIMATIC PCS 7 BOX"). Siemens ST PCS 7.1 Update October 2008 /5

Laboratory automation Siemens AG 2008 /6 Siemens ST PCS 7.1 Update October 2008