Trimble GeoXH and Mobile phone connection In the main Windows screen, pick on the Start menu and then pick settings. In the Wireless Manager disable wireless internet and enable Bluetooth. In the settings window, pick on the connections tab on the bottom of the screen. Then double click on Bluetooth to pair your data collector with your VRS cell phone. You will want to check the box next to Turn on Bluetooth and also check the box next to Make this device discoverable to other devices. Sometimes you have to scan with your cell phone to find the data collector if it won t find your cell phone. Dalia Prizginiene 1
Pick on the devices tab on the bottom of the screen. To pair your cell phone, pick on New Partnership and your data collector will search for the phone. Once it finds it, you phone may ask for a pass key. Type in 1 2 3 4 and also type it in again when your data collector asks for the pass key. Once that is done, your data collector and your cell phone should be successfully paired. You will now be able to see it on your devices list. (In the phone set the data controller GeoXH as trusted for such a connection if it is possible ) Once your device is found, select it on the list and pick next. At this screen, you will want to make sure that you have the Dialup Networking checked. Then pick Save. The phone itself has to have DUN (dialup networking possibility) Once you are back at this screen, pick OK in the upper right corner. Dalia Prizginiene 2
When you are back in this screen, pick on the Connections icon to set up your ISP connection. Under the My ISP heading, pick on Add new modem connection In this screen, first type in a name for your new connection. Then, under the select a modem heading, pick Bluetooth in the pull down. Then pick Next on the bottom of the screen. Dalia Prizginiene 3
Once you are in this screen, select your phone that your partnered up with the data collector and then pick Next on the bottom of the screen. In this screen, type in the dial string that your cell phone provider requires to connect to the web. Then pick Next on the bottom of the screen. For siminn *99***1# For Vodafone *99# For Alterna *99***1# Enter in your username and password that your cell phone provider requires to connect to the web. For siminn: For Vodafone: Alterna: Username: siminn none none Password: siminn none none Pick on the Advanced button. Dalia Prizginiene 4
If your provider requires a special modem command, in the advanced settings box, type in the special modem command that is required by your cell phone provider. For siminn: +cgdcont=1, ip, internet.is For Vodafone: +cgdcont=1, ip, gprs.is For Alterna: +cgdcont=1, ip, gprs.imc.is When you are back in this screen, pick Finish on the bottom of the screen. (The domain box is to be left blank). After you pick finish, you will be brought back to this screen. Again pick Manage existing connections. Dalia Prizginiene 5
In this screen, you should see the connection you just made, along with the dial string. Pick and hold down on the connection and then pick connect on the pull down. This is a test to see if your GeoXH will successfully connect to the web via your phone. It should say that it is dialing, then the box will disappear. To check if it has connected, pick on the two arrows on the top of the screen next to the speaker icon. You will get a box that has a counter on it and a button that says disconnect. That means you are connected, so you can go ahead and pick Disconnect. Now, when you are connected to the internet run TerraSync software and go to setup. In GPS settings: NMEA Output: ON. In real-time settings : Choice 1: External source: Type: VRS Connection method: Internet Address: 213.167.147.216 Port: 2101 Source: select one from the table. Connection control: auto Real-time protocol: RTCM Choice 2: Wait for real-time Real-time age limit: 15-20sec. Source Table: Select the stream from the table. Go back to TerraSync software s setup by pushing OK button. There in setup window of TerraSync, push the GPS button to receive the corrections. If you are using external antenna, the button External source will appear beside the GPS button push that button. If you want to start measurements go to Setup/Data and push the button Create. Dalia Prizginiene 6