Howto Guide Modem Router Connection DLINK DSL-2750B (wifi). PPPoE Configuration Hardware overview Please read the instructions over the page before plugging in your new Modem Router.
1. If the router is new, unbox and plug in via Ethernet cable to your pc. This is the Yellow cable in the box with the router. NOTE: If we have already configured your modem, you can use wifi to connect to the modem. You will find the wifi network name and SSID (Password) on the bottom of the device. If you do not know the wifi name and password, contact our service desk for assistance. The Router must be used with the power adapter included with the device. Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Router and plug the adapter into a suitable nearby power source. Push down the Power button, and you should see the Power LED indicator light up and remain lit. If the Ethernet port is connected to a working device, check the Ethernet Link/Act LED indicators to make sure the connection is valid. Once connected, set your PC s IP settings to DHCP 2. If the modem is existing, but you are experiencing problems, you might use the Reset button on the rear of the unit. HOW DO I RESET MY DSL- 2750B ROUTER TO FACTORY DEFAULT SETTINGS?!! Warning only do this if instructed by a Living Networks Staff Member!! - Ensure the router is powered on. - Press and hold the reset button on the rear of the device for 10 seconds. Note: Resetting the router to factory default will erase the current configuration settings. You won t be able to connect to the Internet until it is reconfigured. To reconfigure your settings, log into the router, then run the Setup Wizard. Seek assistance from Living Networks before resetting the modem/router.
If you need to configure a new Router, or reconfigure your existing router, use the following steps: 3. Open a web browser, and enter: 192.168.1.1 in the address bar enter the username: admin password: admin 4. you should be presented with the following screen: 5. click on setup Wizard
6. click next Ph: 1300 650 679 7. click skip
8. click the check box to Automatically Synchronise with Internet time servers also set the time zone to Perth scroll down to the bottom of the page, and click next
9. uncheck enable DSL autoscan 10. Follow the connection parameters in this screenshot. Australia Others PPPoE LLC/SNAP- BRIDGING VPI: 8 VCI: 35 Then click NEXT 11. enter the pppoe username and password (if unsure ring the helpdesk)
12. check Enable Your Wireless Network box to enable your wireless network. Enter Wireless Network Name (SSID) to identify your wireless network. Visibility Status selects Visible can be found by wireless clients, Invisible to hide your wireless network Choose one wireless encryption mode for your wireless network. (Normally WPA2- PSK is the best to choose) Security Level form low to high as below: None < WEP < WPA- PSK < WPA2- PSK Ph: 1300 650 679 We recommend WPA2- PSK as your security level. Select the button as shown and Enter your desired Wifi Password as the WPA2 Pre- Shared Key
13. CONFIGURE LOCAL NETWORK Ph: 1300 650 679 Configure the DSL IP Address and Subnet Mask for Lan interfance. Default setting as below: IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 Check Enable DHCP Server box to config DHCP IP Address Range and DHCP Lease Time. Default setting as below: DHCP IP Address Range: 192.168.1.2 to 192.168.1.254 DHCP Lease Time: 24 hours Checked the Configure the second IP Address and Subnet Mask for Lan interfance box to enter the second IP address and Subnet Mask. Click on the Next button to go to the next Setup Wizard window. 14. COMPLETED AND APPLY Click Finish button to complete Setup
15. (Optional) if you have any difficulty with wifi after committing settings, You can manually check your Wifi settings in Wireless setup. set wifi to auto and wpa- psk if you have any trouble with wifi Enjoy your time on the Internet!