specifications Mechanical dimensions 1 SDsa28B2W 1. Dimension in millimeter (inch), and tolerance is 0.25 (.01) specified. 2. Specifications are subject to change without notice. nal EQuIvaLEnT CIRCuIT mended ng Pattern 1. Dimension in millimeter 1. (inch), Dimension and in tolerance millimeter is (inch), 0.25 (.01) and specified. tolerance is 0.25 2. Specifications are subject 2. Specifications to change without are subject notice. to change without notice. TyPICaL InTERnaL TyPICaL EQuIvaLEnT InTERnaL EQuIvaLEnT CIRCuIT CIRCuIT Recommended Recommended Soldering Pattern Soldering Pattern TyPICaL InTERnaL EQuIvaLEnT CIRCuIT Recommended Soldering Pattern Common Cathode 12 PIN No Connect 3 Notes: Common Cathode Common Cathode 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.25mm (0.01 ) unless otherwise noted. 12 PIN No Connect 12 PIN No Conn 3 E. Lexington Ave., Pomona CA 91766 Tel: 909-465-0080 Fax: 909-465-0130 www.aopled.com 3. Specifications are subject to change without notice. Version: A Date: 4/23/2009 Version: A Date: 4/23/2009 American Opto Plus LED American Corp. 1206 Opto E. Lexington Plus LED Corp. Ave., Pomona 1206 E. Lexington CA 91766 Ave. Tel:, 909-465-0080 Pomona CA 91766 Fax: 909-465-0130 Tel: 909-465-0080 www.aopled.com Fax: 909-465-0130 w Part Number Chip Material Color of Emission Lens Type Description SDsa28B2W InGaN Blue White Segment Common Anode Common Cathode 12 PIN No Connect
2 ABSOLUTE MAXIMUM RATINGS (Ta=25 C) Parameter Symbol Value Unit Power Dissipation per Dice Pad 120 mw Derating Liner from 25 C per Dice - 0.3 ma / c Continuous Forward Current per Dice Iaf 30 ma Peak Current per Dice (duty cycle 1/10, 1kHz) Ipf 100 ma Reverse Voltage per Dice Vr 5 V Operating Temperature Topr -40~+105 c Storage Temperature Tstg -40~+105 c OPTICAL-ELECTRICAL CHARACTERISTICS (Ta=25 C) Characteristic Symbol Condition Value Min. Type. Max. Unit Forward Voltage per Dice Vf If = 5mA - 2.85 3.0 V Reverse Current per Dice Ir Vr = 8V - - 10 µa Peak Wavelength per Dice λp If = 5mA - 472 - nm Dominant Wavelength per Dice λd If = 5mA 450 470 480 nm Luminous Intensity per Dice Iv If = 5mA 10 30 - mcd Spectral Radiation Bandwidth per Dice Δλ If = 5mA - 30 - nm *Tolerance of viewing angle: -10 / +5 deg.
3 optical characteristic curves Typical Electro-optical Characteristic Curves (25 Free air Temperature Unless Otherwise Specified)
4 soldering conditions lamp type led SMT LOW SOLDERING INSTRUCTIONS SMT Soldering Profile Pb free reflow soldering Profile 5 SEC. TEMPERATURE 217 C 200 C 150 C 255-260 C 3 C/SEC.MAX. 3 C/SEC.MAX. 6 C/SEC.MAX. 60-120SEC. 100SEC.MAX. SOLDERING IRON TIME Basic spec is 4 sec when 260 C. If temperature is higher, time should be shorter (+10 C 1 sec). Power dissipation of Iron should be smaller than 15W, and temperature should be controllable. Surface temperature of the device should be under 230 C. REWORK Customer must finish rework within 5 sec. under 260. The head of soldering iron cannot touch copper foil.
5 Dimensions of Tape (Unit: mm) Packaging specification