R Thank you for purchasing the Maxxsonics ipod / MP3 interface module. This model allows you to connect your ipod / MP3 music source directly into your aftermarket amplifier with out having to use a radio frequency transmitter that degrades the signal path and sound quality performance. Enjoy the direct wire benefits of the and the outstanding sound quality it provides. FEATURES R - COMPATIBLE WITH ALL ipod / MP3 PLAYERS / SATELLITE RADIOS - BLUE LED VOLUME KNOB BACK LIGHTING - ILLUMINATED MAXXSONICS LOGO - SMALL IN OR UNDER DASH CONTROL HEAD WITH 3.5mm HEADPHONE - HEADPHONE INTERFACE CABLE INCLUDED - ADJUSTABLE LEVEL CONTROL - AUTOMATIC RADIO BYPASS CIRCUIT - ULTRA-LOW THD & N CIRCUITRY - UNDER-DASH OR HIDDEN MAIN MODULE - INSTALLATION HARDWARE INCLUDED R R ipod is the registered trademark of Apple Computer, Inc, which is not affiliated with this product. Maxxsonics is not R an agent or affiliated in any way with Apple Computer, Inc. 1
OPERATING INSTRUCTIONS The is an interface module installed in-between the radio and aftermarket amplifier that allows you to connect your ipod / MP3 audio player directly into your aftermarket amplifier with out having to use a sound quality degrading FM or AM adaptor. NOTE: The radio signals travel into the main control module and pass through to the amplifier. When the headphone cable is plugged into the control head, the radio signal will be bypassed so that the ipod / MP3 signals can be routed directly to the amplifier. When the headphone cable is unplugged, the radio signal path will be restored directly to the amplifier for normal operation. Please follow the directions below. 1. Turn the radio / CD player off. 2. Plug one end the 3.5mm headphone adaptor cable into the ipod / MP3 player headphone output jack as shown below. 3. Plug the other end of the 3.5mm headphone adaptor cable into the control head 3.5 mm jack. NOTE: The radio will not play as long as the headphone adaptor cable is plugged in. 4. Turn the volume to minimum 5. Turn the ipod / MP3 player volume to maximum. 6. Turn the Radio / CD player on (note: radio must be on to use ) 7. Adjust the volume to your preferred listening level. Note: The radio volume control will not affect the ipod / MP3 volume level. MAXXSONICS Headphone Adaptor Cable MIN MAXX Control Head HEADPHONE JACK MP3 Player 2
INSTALLATION INSTRUCTIONS CONTROL MODULE WIRING 1. Using a small flat blade screw driver, connect 3 different color wires (one each) to the green power connector on the back of the module labeled - REM +. We recommend you choose red for +, black for - & blue for REM. 2. Connect the + (red wire) to a constant + 12 volt source such as the radio power wire with an in-line 5 amp fuse. 3. Connect the - (black wire) to a good chassis ground source. Note: Be sure to remove all paint and primer to expose clean metal. Use a nut, bolt and lock washer to secure the ground wire. 4. Connect the REM remote turn-on (blue wire) to the radio remote turn-on wire. CONTROL MODULE RCA CONNECTIONS 1. If the radio / CD player has front (L & R) and rear (L & R) RCA outputs, plug them into the Control Module connectors. 2. Connect good quality RCA cables into the Control Module OUTPUT connectors. 3. Route the OUTPUT RCA cables to the amplifier RCA S as specified in your amplifier installation manual. CONTROL MODULE 1. Plug the RJ45 cable into the Control Module and route to the location you have chosen to mount the Control Head 2. Mount the Control Module in a concealed location under the dash board. CONTROL HEAD 1. Mount the control head under the dash with the supplied C Bracket and hardware supplied or in the dash in a location easily accessible by the driver. 2. Plug the RJ45 cable into the back of the Control Head. 3
WIRING DIAGRAM BACK OF CONTROL HEAD FRONT OF CONTROL HEAD MAXXSONICS 36 rj45 cable to connect the control head to the control module. FRONT CONTROL MODULE BACK CH1 CH3 LEVEL OUTPUT CH2 CH4 - REM + 6V - 0.2V Connect to Radio / CD player RCA Front (L & R) and Rear (L & R) RCA outputs To Battery (+) With 5-Amp Fuse Remote Input (Turn-On Input) Chassis Ground Connect to Amplifier RCA Front (L & R) and Rear (L & R) RCA inputs MAXXSONICS 30 3.5mm headphone cable MP3 Player 4
DIMENSIONS 5.5 4.9 4.75 5.5 6.75 1.9 2.25 1.75 1 1.25 1 2.75 5
Maxxsonics Limited Warranty As the manufacturer of Maxxsonics, Autotek, MB Quart, Crunch and Hifonics car audio products, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one (1) Year from date of purchase. All other parts and accessories of the system are warrantied to be free from defects in material and workmanship for one (1) year from date of purchase. Maxxsonics will repair or replace at it s option and free of charge during the warranty period, any system component that proves defective in materials and workmanship under normal installation, use and service provided that the product is returned to the authorized Maxxsonics dealer from where it was purchased. A photo copy of the original receipt must accompany the product being returned. Valid purchase receipts will contain the name and address of the authorized reseller. Any damage to the product as a result of misuse, abuse, accident, incorrect wiring, improper installation, alteration of date code or bar code labels, revolution, natural disaster, or any sneaky stuff because someone messed up, repair or alteration out side of our factory or authorized service centers and any thing else you have done that you should not have done is not covered. This warranty is limited to defective parts and specifically excludes any incidental or consequential damages connected therewith. This warranty is not to be construed as an insurance policy. Warranty on installation labor, removal, re-installation and freight charges are not the responsibility of Maxxsonics USA Inc. Warranty products damaged as a result of insufficient or improper packing materials are not covered by this limited warranty and such damaged product will be returned as is at the expense of the owner. 6