CEAG HandRail 930XX LED Hand rail mounted Luminaire for all applications
Safety luminaire When confronted with emergency lighting applications where a ceiling or post top mounting is not possible, Eaton offer a broad innovative low power hand hail mounted emergency luminaire. The hand rail luminaire has an outstanding performance with superior photometric and spacing. The flexible hand rail luminaire mounts within a tube, options for 42mm or 51mm (outer diameter) to provide a compact, slim and unobtrusive design with smooth edging to eliminate finger trap hazards. Features Selection of special optics for a variety of applications Selection of drivers to optimise performance requirements minimising energy consumption Monitored and un-monitored options for design flexibility High IP and IK rating for indoor and outdoor applications Available with a fully monitored CG-S solution or suitable for use with third party drivers as a un-monitored solution. It is ideally suited as a compensation measure for escape route / safe egress lighting and architectural decorative lighting. SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 2
HandRail 93011 LED ** * ** ** HandRail 930XX LED Safety luminaire in LED technology for mounting into handrail Can be mounted in stainless steel, galvanized steel or plastic handrail Discrete mounting for improved aesthetics Superior spacing due to optics technology and highly efficient HighPower LEDs Suitable for indoor and outdoor applications Up to 11 m from luminaire to luminaire with optics for open area illumination Minimum service requirement due to high service life of the LEDs (50,000 hours) Luminous flux Φ N 350 ma: 118 lm 490 ma: 164 lm 700 ma: 235 lm HandRail 93012 LED Luminous flux Φ E /Φ N at end of rated operating time Housing material Housing colour Weight Power supply Permissible ambient temperature 100% Polycarbonate, Aluminium Aluminium 0.068 kg Recessed mounting into handrail approx. 3V DC, max 700 ma (constant current) -20 C to +50 C Light source 1 x High Power LED (U F = 2.8 V... 3.15 V) HandRail 93015 LED Ordering details Type Scope of supply Order No. HandRail LED 93011 LED HandRail LED 93012 LED HandRail LED 93015 LED HandRail LED 93021 LED HandRail LED 93022 LED HandRail LED 93025 LED HandRail LED 93011 LED handrail mounting with 70 asymmetric optics for escape route illumination, indoor and outdoor 40071355046 applications, for installation into 42mm diameter handrail (Does not include driver) HandRail LED 93012 LED handrail mounting with asymmetric optics for escape route illumination, indoor and outdoor 40071355051 applications, for installation into 42mm diameter handrail (Does not include driver) HandRail LED 93015 LED handrail mounting for escape route illumination with opal lens, indoor applications only, for installation into 42mm diameter handrail (Does not include driver) 40071355049 HandRail LED 93021 LED handrail mounting with 70 asymmetric optics for escape route illumination, indoor and out- 40071355050 door applications, for installation into 51mm diameter handrail (Does not include driver) HandRail LED 93022 LED handrail mounting with asymmetric optics for escape route illumination, indoor and outdoor 40071355047 applications, for installation into 51mm diameter handrail (Does not include driver) HandRail LED 93025 LED handrail mounting for escape route 40071355048 illumination with opal lens, indoor applications only, for installation into 51mm diameter handrail (Does not include driver) * Degree of protection of the luminaire: IP66 Degree of protection of the Eaton driver housing: IP20 ** Only with Eaton Emergency Lighting LED driver SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 3
V-CG-SLS xxx V-CG-SLU xxx Ordering details modules Number of HandRail Luminaires LED Driver* Constant current Minimum Maximum Order No. V-CG-SLS 701 700 ma 1 1 40071352399 V-CG-SLS 501 500 ma 1 1 40071352369 V-CG-SLS 500 500 ma 2 2 40071352418 V-CG-SLS 350 350 ma 2 4 40071352417 V-CG-SLR 350 350 ma 2 4 40071352420 V-CG-SLU 700 700 ma 2 4 40071352917 V-CG-SLU 490 490 ma 2 4 40071352916 V-CG-SLU 350 350 ma 2 4 40071352915 Optional IP66 rated installation box suitable for 2 x V-CG-SLU xxx 40071355090 * Detailed LED drived data - see catalogue pages Monitoring and Lamp Control Gear Modules Attention: V-CG-SLI is not suitable V-CG-SLR 350 Schematic drawing of driver and luminaire/s -Ve +Ve -Ve +Ve -Ve +Ve -Ve +Ve! IMPORTANT: Connection of driver to luminaires is a series connection NOT parallel. Numbers of possible HandRail luminaires per LED driver see table above - + Installations Box, -Ve +Ve -Ve +Ve -Ve +Ve -Ve +Ve 253 200 120 Type Suitable HandRail/ Optic Recommended application Pipe diameter 93011 LED 42.4 x 2.0 70 Lens Trackside and walkways handrails (level surface) 93012 LED 42.4 x 2.0 Lens Walkways and stair handrails 93015 LED 42.4 x 2.0 No optic, Opal diffuser Walkways and stair handrails (low glare) 93021 LED 51.0 x 3.8 70 Lens Trackside and walkways handrails (level surface) 93022 LED 51.0 x 3.8 Lens Walkways and stair handrails 93025 LED 51.0 x 3.8 No optic, Opal diffuser Walkways and stair handrails (low glare) 75 SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 4
LED driver 700 ma Planning assistance for HandRail 930x1 LED (70 ) for E = 1.0 lx (10.8 lx) 1000 1500 2000 HandRail 930x1 LED 0.8 Handrail mounting 4.2 (1.6) 9.2 (5.6) 0.5 (0.5) 0.9 Escape route center 4.6 (1.9) 10.1 (7.1) 0.5 (0.5) 1 5.0 (2.6) 11.0 (8.1) 0.5 (0.5) Planning assistance for HandRail 930x2 LED () for E = 1.0 lx (10.8 lx) 400 HandRail 930x2 LED 0.8 Handrail mounting 2.35 (1.75) 5.05 (3.6) 0.5 (0.5) 0.9 Escape route center 2.5 (1.85) 5.4 (3.85) 0.5 (0.5) 1 2.6 (1.95) 5.7 (4.1) 0.5 (0.5) Planning assistance for HandRail 930x5 LED (opal) for E = 1.0 lx (10.8 lx) 200 HandRail 930x5 LED 0.8 Handrail mounting 2.4 (1.7) 6.0 (4.25) 0.5 (0.5) 0.9 Escape route center 2.5 (1.8) 6.3 (4.45) 0.5 (0.5) 1 2.6 (1.8) 6.55 (4.65) 0.5 (0.5) 70 h L1 L2 25 L3 SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 5
LED driver 490 ma / 500 ma Planning assistance for HandRail 930x1 LED (70 ) for E = 1.0 lx (10.8 lx) 1000 1500 2000 HandRail 930x1 LED 0.8 Handrail mounting 4.05 (1.4) 8.9 (3.3) 0.5 (0.5) 0.9 Escape route center 4.4 (1.6) 9.75 (6.0) 0.5 (0.5) 1 4.75 (1.8) 10.55 (6.9) 0.5 (0.5) Planning assistance for HandRail 930x2 LED () for E = 1.0 lx (10.8 lx) 400 HandRail 930x2 LED 0.8 Handrail mounting 2.2 (1.6) 4.7 (3.3) 0.5 (0.5) 0.9 Escape route center 2.3 (1.7) 5.0 (3.6) 0.5 (0.5) 1 2.45 (1.8) 5.25 (3.8) 0.5 (0.5) Planning assistance for HandRail 930x5 LED (opal) for E = 1.0 lx (10.8 lx) 200 HandRail 930x5 LED 0.8 Handrail mounting 2.15 (1.4) 5.4 (3.7) 0.5 (0.5) 0.9 Escape route center 2.25 (1.5) 5.6 (3.9) 0.5 (0.5) 1 2.35 (1.55) 5.85 (4.1) 0.5 (0.5) L1 L3 L2 70 L1 L1 L3 L1 h SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 6
LED driver 350 ma Planning assistance for HandRail 930x1 LED (70 ) for E = 1.0 lx (10.8 lx) 1000 1500 2000 HandRail 930x1 LED 0.8 Handrail mounting 3.9 8.55 0.5 (0.5) 0.9 Escape route center 4.2 9.35 0.5 (0.5) 1 4.55 10.1 0.5 (0.5) Planning assistance for HandRail 930x2 LED () for E = 1.0 lx (10.8 lx) 400 HandRail 930x2 LED 0.8 Handrail mounting 2.05 4.53 0.5 (0.5) 0.9 Escape route center 2.15 4.65 0.5 (0.5) 1 2.3 4.9 0.5 (0.5) Planning assistance for HandRail 930x5 LED (opal) for E = 1.0 lx (10.8 lx) 200 HandRail 930x5 LED 0.8 Handrail mounting 1.95 4.85 0.5 (0.5) 0.9 Escape route center 2.0 5.05 0.5 (0.5) 1 2.1 5.25 0.5 (0.5) h L1 L2 25 L3 SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 7
V-CG-SLU 700 V-CG-SLU 700 Low operating costs due to decreased standby losses < 0.7 W Minimized dimensions on the basis of conventional T5 EVG cross section (H x B: 21 x 30 mm) for an eased mounting in narrow luminaires Without protective conductor connection. For the use in luminaires with insulation class I or II Variable mounting possibilities for different mounting positions (horizontal or sidewise upright) Avoidance of installation failures due to a mains connection being protected against polarity reversal Shortened inspection effort due to the CEWA GUARD- and S + -Technology: Automatic function monitoring of up to 20 luminaires per circuit Reduced installation costs due to STAR-Technology: Freely programmable mixed operation of the switching modes per luminaire in one circuit Reduced installation expenditures as no additional data line to the luminaires is needed 4.3 130 139 30 130 Module housing 262 195 21 26 86 Primary side Rated voltage ranges Standby power loss Current consumption Power input 220-240 V, 50/60 Hz / 176-275 V DC < 0.7 W (230 V / 50 Hz) 93 ma (230 V AC) / 56 ma (220 V DC) 21.4 VA (230 V AC) Power factor 0.52...0.61 Inrush current Operating frequency EEI Connection terminals Secondary side Output current Output voltage Lamp load Output power (max.) Connection terminals Maximum line length Degree of protection 3.0 A 25-130 khz A2 Clamp terminals 2.5 mm 2 / reverse-polarity protected 700 ma (constant current) 14 V DC (open-circuit operation) 1-4 LEDs (rated current 700 ma, UF = 2.85... 3.5 V), series connection 9.8 W Clamp terminals 1.5 mm 2 / not reverse-polarity protected 1 m (module LED) To be mounted in luminaires with protection category I or II IP20 Permissible ambient temperature ta = 20 C to +50 C Maximal permissible test point temperature tc = 70 C (H x L x B) 21 x 139 x 30 Housing material / Colour Weight Flame retardant polycarbonate / grey 0.061 kg Luminous flux Φ E /Φ N at the end of rated operating time 100 % 46 Ordering details Without individual packaging Individual packaging Scope of supply Order No. Order No. V-CG-SLU 700 40071352917 40071352947 Module housing with strain relief 40071352765 SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 8
V-CG-SLU 490 V-CG-SLU 490 Low operating costs due to decreased standby losses < 0.7 W Minimized dimensions on the basis of conventional T5 EVG cross section (H x B: 21 x 30 mm) for an eased mounting in narrow luminaires Without protective conductor connection. For the use in luminaires with insulation class I or II Variable mounting possibilities for different mounting positions (horizontal or sidewise upright) Avoidance of installation failures due to a mains connection being protected against polarity reversal. Shortened inspection effort due to the CEWA GUARD- and S + -Technology: Automatic function monitoring of up to 20 luminaires per circuit Reduced installation costs due to STAR-Technology: Freely programmable mixed operation of the switching modes per luminaire in one circuit Reduced installation expenditures as no additional data line to the luminaires is needed 4.3 130 139 30 130 21 Primary side Rated voltage ranges 220-240 V, 50/60 Hz / 176-275 V DC Standby power loss < 0.7 W (230 V / 50 Hz) Current consumption 67 ma (230 V AC) / 41 ma (220 V DC) Power input 15.4 VA (230 V AC) Power factor 0.45...0.59 Inrush current 3.0 A Operating frequency 25-130 khz EEI A2 Connection terminals Clamp terminals 2.5 mm 2 / reverse-polarity protected Module housing 262 195 26 86 Secondary side Output current Output voltage Lamp load Output power (max.) Connection terminals Maximum line length Degree of protection 490 ma (constant current) 14 V DC (open-circuit operation) 1-4 LEDs (rated current 490 ma, UF = 2.85... 3.5 V), series connection 6.9 W Clamp terminals 1.5 mm 2 / not reverse-polarity protected 1 m (module LED) To be mounted in luminaires with protection category I or II IP20 Permissible ambient temperature ta = 20 C to +50 C Maximal permissible test point temperature tc = 70 C (H x L x B) 21 x 139 x 30 Housing material / Colour Weight Flame retardant polycarbonate / grey 0.061 kg Luminous flux Φ E /Φ N at the end of rated operating time 100 % 46 Ordering details Without individual packaging Individual packaging Scope of supply Order No. Order No. V-CG-SLU 490 40071352916 40071352946 Module housing with strain relief 40071352765 SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 9
V-CG-SLU 350 V-CG-SLU 350 Low operating costs due to decreased standby losses < 0.7 W Minimized dimensions on the basis of conventional T5 EVG cross section (H x B: 21 x 30 mm) for an eased mounting in narrow luminaires Without protective conductor connection. For the use in luminaires with insulation class I or II Variable mounting possibilities for different mounting positions (horizontal or sidewise upright) Avoidance of installation failures due to a mains connection being protected against polarity reversal Shortened inspection effort due to the CEWA GUARD- and S + -Technology: Automatic function monitoring of up to 20 luminaires per circuit Reduced installation costs due to STAR-Technology: Freely programmable mixed operation of the switching modes per luminaire in one circuit Reduced installation expenditures as no additional data line to the luminaires is needed 4.3 130 139 30 130 21 Primary side Rated voltage ranges 220-240 V, 50/60 Hz / 176-275 V DC Standby power loss < 0.7 W (230 V / 50 Hz) Current consumption 91 ma (230 V AC) / 54 ma (220 V DC) Power input 20.9 VA (230 V AC) Power factor 0.44...0.61 Inrush current 3.0 A Operating frequency 25-130 khz EEI A2 Connection terminals Clamp terminals 2.5 mm 2 / reverse-polarity protected Module housing 262 195 26 46 86 Secondary side Output current Output voltage Lamp load Output power (max.) Connection terminals Maximum line length Degree of protection 350 ma (constant current) 28 V DC (open-circuit operation) 1-8 LEDs (rated current 350 ma, UF = 2.85... 3.5 V), series connection 9.8 W Clamp terminals 1.5 mm 2 / not reverse-polarity protected 1 m (module LED) To be mounted in luminaires with protection category I or II IP20 Permissible ambient temperature ta = 20 C to +50 C Maximal permissible test point temperature tc = 70 C (H x L x B) 21 x 139 x 30 Housing material / Colour Weight Flame retardant polycarbonate / grey 0.061 kg Luminous flux Φ E /Φ N at the end of rated operating time 100 % Ordering details Without individual packaging Individual packaging Scope of supply Order No. Order No. V-CG-SLU 350 40071352915 40071352945 Module housing with strain relief 40071352765 SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 10
SAFETY LUMINAIRES Handrail 930XX LED www.ceag.de 11
At Eaton, we re energized by the challenge of powering a world that demands more. With over 100 years experience in electrical power management, we have the expertise to see beyond today. From groundbreaking products to turnkey design and engineering services, critical industries around the globe count on Eaton. We power businesses with reliable, efficient and safe electrical power management solutions. Combined with our personal service, support and bold thinking, we are answering tomorrow s needs today. Follow the charge with Eaton. Visit eaton.eu/electrical. To find your contact person, please visit www.ceag.de/en. Eaton Industries Manufacturing GmbH Electrical Sector EMEA Route de la Longeraie 7 1110 Morges, Switzerland www.eaton.eu CEAG Notlichtsysteme GmbH Senator-Schwartz-Ring 26 59494 Soest, Germany Tel.: +49 (0) 2921 69-870 Fax: +49 (0) 2921 69-617 E-Mail: info-n@eaton.com Web: www.ceag.de 2018 Eaton All Rights Reserved Changes to the products, to the information contained in this document, and to prices are reserved; so are errors and omissions. Only order confirmations and technical documentation by Eaton is binding. Photos and pictures also do not warrant a specific layout or functionality. Their use in whatever form is subject to prior approval by Eaton. The same applies to Trademarks (especially Eaton, Moeller, and Cutler-Hammer). Eaton is a registered trademark. All other trademarks are property of their respective owners.