1
Main Advanced H/W Monitor Boot Security Exit System Overview System Time System Date BIOS Version Processor Type Processor Speed Microcode Update :F7A/3A L1 Cache Size : 128KB L2 Cache Size : 512KB Total Memory DDRII 1 DDRII 2 DDRII 3 DDRII 4 [ 17:00:09] [Wed 07/12/2006] : ALiveNF6G-DVI BIOS P1.0 : AMD Athlon(tm) 64 Processor 3400+ (64bit supported) : 2200 MHz :512MB with 64MB shared memory Dual-Channel Memory Mode : 256MB/266MHz (DDRII533) : 256MB/266MHz (DDRII533) :None :None Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time. +- Change Field Tab Select Field Main Advanced H/W Monitor Boot Security Exit System Overview System Time System Date BIOS Version Processor Type Processor Speed Microcode Update :F7A/3A L1 Cache Size : 128KB L2 Cache Size : 512KB Total Memory DDRII 1 DDRII 2 DDRII 3 DDRII 4 [ 17:00:09] [Wed 07/12/2006] : ALiveNF6G-VSTA BIOS P1.0 : AMD Athlon(tm) 64 Processor 3400+ (64bit supported) : 2200 MHz :512MB with 64MB shared memory Dual-Channel Memory Mode : 256MB/266MHz (DDRII533) : 256MB/266MHz (DDRII533) :None :None Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time. +- Change Field Tab Select Field 2
Main Advanced H/W Monitor Boot Security Exit Advanced Settings Options for CPU WARNING : Setting wrong values in below sections may cause system to malfunction. CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperIO Configuration USB Configuration Enter Go to Sub Screen Advanced CPU Configuration AM2 Boost Overclock Mode CPU Frequency (MHz) PCIE Frequency (MHz) Boot Failure Guard CPU/LDT Spread Spectrum PCIE Spread Spectrum SATA Spread Spectrum Cool'n'Quiet Dual Core Support Processor Maximum Multiplier Processor Maximum Voltage Multiplier/Voltage Change Memory Clock Flexibility Option CAS Latency TRAS [200] [100] [0.75% Hershey] x11 1.550 V If AUTO, multiplier and voltage will be left at the rated frequency/voltage. If Manual, multiplier and voltage will be set based on User Selection in Setup. +- Change Option F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 3
4
Advanced CPU Configuration AM2 Boost Overclock Mode CPU Frequency (MHz) PCIE Frequency (MHz) Boot Failure Guard CPU/LDT Spread Spectrum PCIE Spread Spectrum SATA Spread Spectrum Cool'n'Quiet Dual Core Support Processor Maximum Multiplier Processor Maximum Voltage Multiplier/Voltage Change Processor Multiplier Processor Voltage [200] [100] [0.75% Hershey] x11 1.550 V [Manual] [x8] [1.500V] If AUTO, multiplier and voltage will be left at the rated frequency/voltage. If Manual, multiplier and voltage will be set based on User Selection in Setup. +- Change Option F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 5
6
Chipset Settings Onboard LAN Onboard HD Audio Front Panel Controller Share Memory Primary Graphics Adapter CPU-NB Link Speed CPU-NB Kink Width DRAM Voltage Advanced [PCI] To set DRAM Voltage. + - Change Option 7
Advanced ACPI Settings Suspend To RAM Repost Video on STR Resume Away Mode Support Restore on AC / Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On ACPI HPET Table [No] [Power Off] Select auto-detect or disable the STR feature. +- Change Option 8
Advanced IDE Configuration OnBoard IDE Controller OnBoard SATA Controller SATA Operation Mode IDE Master IDE Slave SATAII 1 SATAII 2 SATAII 3 SATAII 4 [non-raid] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] ENABLED: enables the integrated IDE Controller. DISABLED: disables the integrated IDE Controller. +- Change Option F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit Advanced IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. :Hard Disk :MAXTOR 6L080J4 :80.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-6 :Supported Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer Select the type of device connected to the system. +- Change Option 9
10
Advanced Advanced PCI / PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction. ValueinunitsofPCI clocks for PCI device latency timer register. PCI Latency Timer PCI IDE BusMaster [64] +- Change Option Advanced Floppy Configuration 1 Floppy A [1.44 MB 3 2 "] Select the type of floppy drive connected to the system. +- Change Option 11
Advanced Configure Super IO Chipset OnBoard Floppy Controller Serial Port Address Infrared Port Address Parallel Port Address Parallel Port Mode EPP Version ECP Mode DMA Channel Parallel Port IRQ OnBoard Game Port OnBoard MIDI Port [3F8 / IRQ4] [378] [ECP + EPP] [1.9] [DMA3] [IRQ7] Allow BIOS to Enable or Disable Floppy Controller. +- Change Option 12
Advanced USB Configuration USB Controller USB 2.0 Support Legacy USB Support To enable or disable the onboard USB controllers. +- Change Option 13
Main Advanced H/W Monitor Boot Security Exit Hardware Health Event Monitoring CPU Ambient Temperature CPU Internal Temperature M / B Temperature : 42C/107F : 52C/125F : 31C/87F CPU Fan Speed Chassis Fan Speed : 2833 RPM :N/A Vcore + 3.30V + 5.00V + 12.00V CPU Quiet Fan : 1.532 V : 3.129 V : 4.877 V : 11.741 V F1 F9 F10 ESC General Help Load Defaults Save and Exit Exit 14
Main Advanced H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration Configure Settings during System Boot. 1st Boot Device 2nd Boot Device 3rd Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [HDD: PM-MAXTOR 6L08] [CD/DVD: SM-CD-ROM] Enter Go to Sub Screen Boot Boot Settings Configuration Boot From Network Bootup Num-Lock [On] To enable or disable the boot from network feature. + - Change Option 15
Main Advanced H/W Monitor Boot Security Exit Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password Change User Password Install or Change the password. Enter Change 16
Main Advanced H/W Monitro Boot Security Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Enter Go to Sub Screen 17
18