kéï=~ë=çñw== MOKOMMU `bob`=pa pçñíï~êé=réç~íéi=séêëáçå=pknm= båöäáëü
Table of contents Sirona Dental Systems GmbH Table of contents 1 Installation... 3 1.1 General information... 3 1.2 System requirements... 3 1.3 Installing CEREC 3D software... 3 1.4 Activating all milling instruments... 4 1.5 Installing the software on the milling unit (download) 5 1.5.1 Download via the DECT radio interface... 5 1.5.2 Procedure in case of problems downloading via the DECT radio interface... 7 1.5.3 Download via the Höft&Wessel radio interface 7 1.5.4 Procedure in case of problems downloading via the Höft&Wessel radio interface... 9 1.5.5 Download via the Futaba FRH-SD03Tx radio interface 9 1.5.6 Procedure in case of problems downloading via the Futaba FRH-SD03Tx radio interface... 11 1.5.7 Download using the serial cable supplied... 11 1.5.8 Procedure in case of problems downloading with the supplied serial cable... 13 2 Software Update, Version 3.1X... 14 2.1 General information... 14 2.2 Failure to detect the new baud rate... 14 2.3 Wrong blocks in the block selection dialog... 14 2.4 MC XL... 14 2.5 Displacement of the proximal contact line during inlay correlation... 15 2.6 Prepositioning tool for crown dental database (in 3D mode)... 15 2.7 Simultaneous display of occlusal and proximal contact points... 15 2.8 Loading of restorations in CEREC 3D Mode and Master Mode... 16 2.9 VITABLOCS TriLuxe forte... 16 2.10 New milling instruments... 16 2.11 New materials from 3M ESPE... 16 2.12 Windows Vista compatible... 17 2 D 3439.116.10.05.02 02.2008
Sirona Dental Systems GmbH 1 Installation General information 1 Installation 1.1 General information Administrator rights NOTE: Installation only with administrator rights You must have administrator rights on the PC on which you want to install the software! Notes on the software version Notes on this software version You can load a restoration made with an earlier software version with this version as well. However, once this restoration has been saved with the current software version, it can no longer be loaded with the earlier software version. The restoration can be saved according to the following procedures: By selecting "Restoration" / "Save". By selecting "Restoration" / "Save as ". Automatically, by confirming the image catalog with the "Next" icon. Automatically, by pressing the "Mill" icon. Automatically, during virtual seating ("Design" / "Quadrant ".) Parameters NOTE: Adjusting parameters after the installation Following the installation of the software all parameters are set to the recommended factory settings. If you install this software over an existing CEREC 3D software and wish to retain your parameter settings, adjust the parameter values as desired after the installation. 1.2 System requirements The hardware version of the acquisition unit must be PC Hardware EA or higher. 1.3 Installing CEREC 3D software Installing the software Performing the installation The PC is powered up and all programs are terminated. 1. Insert the CD in the CD/DVD drive. The setup program starts automatically. 2. If this is not the case, run the "Setup.exe" file in the root directory of the CD. 3. Select the language of the installation and click the "OK" button. The installation wizard opens. 4. Click the "Next" button. The license agreement appears. 5. Accept the license agreement with the Yes button. The installation routine continues. D 3439.116.10.05.02 02.2008 3
1 Installation Sirona Dental Systems GmbH Activating all milling instruments Standard installation Selecting the standard installation 1. Click the "Standard Installation" button. NOTE: Installing DirectX If DirectX is not yet installed on your computer, it will be installed now. Accept the license agreement and decide whether the computer is to be restarted now or later. New milling program New milling program 2. To complete the installation, you can register to receive current information on software updates and/or have the "ReadMe" file displayed. This file contains the latest information on the software. Select or deselect the corresponding checkbox. 3. Click the "Finish" button. 4. Decide whether the computer should be restarted now or later and click the "Finish" button. CAUTION: Transferring the milling program Following installation of the new software, the new milling program must be transferred to the milling unit (see "Installing the software on the milling unit (download) [ 5]). 1.4 Activating all milling instruments CEREC 3 milling unit In the factory default condition in CEREC 3D mode you can select the Step bur 10 and Cylinder Pointed Bur milling instruments in the dialog "Change instruments". When you switch to Master Mode all possible milling instruments will be displayed. If you switch the Step bur 10 and Cylinder Pointed Bur milling instruments to another possible combination in Master Mode, this setting will be saved. When you switch to CEREC 3D mode again, all possible milling instruments will also be displayed in CEREC 3D mode. CEREC MC XL All milling instruments are available in CEREC 3D mode as well as in the Master Mode. 4 D 3439.116.10.05.02 02.2008
Sirona Dental Systems GmbH 1 Installation Installing the software on the milling unit (download) 1.5 Installing the software on the milling unit (download) When installing the software update, it is necessary to install the corresponding software on the milling unit again. 1.5.1 Download via the DECT radio interface Preparations Preparations 1. For this installation step, place your PC as close as possible to the milling unit. 2. Switch on the PC. The milling unit must be switched off. Performing a download, DECT, new Downloading the milling program Switching the milling unit on (DECT) Switch the milling unit on (B), while keeping the download key (A) pressed. Wait until the left operating indicator (C) of the radio interface on the milling unit lights up continuously. You can now release the Download key on the milling unit. The green LED on the milling unit is lit and the yellow LED is off. Software note for CEREC 3D Software versions NOTE: For a software update/upgrade from Version 2.8X to Version 3.1X, the milling software is automatically downloaded to the milling unit when the CEREC 3D user software is started. In this case, the steps described are not required after starting the CEREC 3D program. For a software upgrade from Version 2.6X or lower to Version 3.1X, proceed as follows. Configuring the milling unit Configuring the milling unit 1. Start the CEREC 3D program. The message "Downloading software to COMx" (COM1, COM2,... depending on which interface the milling unit is connected to) appears in the status bar. Wait until the status display goes out. 2. Select the menu item "Settings"/"Configuration"/ "Devices...". 3. Select the milling unit to be configured in the "Configure Devices" dialog box and click the "Configure" button. D 3439.116.10.05.02 02.2008 5
1 Installation Sirona Dental Systems GmbH Installing the software on the milling unit (download) Installation completed 4. Enter a name for this milling unit ("Milling unit" is offered as the default name). 5. Corresponding to your unit configuration, place a checkmark in front of "Scanner", in front of "inlab gearhead installed" and, if installed, in front of "Large watertank". 6. Click "OK". 7. After a successful download, a green check mark appears next to the milling unit symbol if the milling unit and scanner were calibrated beforehand. Click the "OK" button to close the "Configure Devices" dialog box. The installation is now completed. Should problems have occurred in one of the above items, please observe the instructions on the next page 6 D 3439.116.10.05.02 02.2008
Sirona Dental Systems GmbH 1 Installation Installing the software on the milling unit (download) 1.5.2 Procedure in case of problems downloading via the DECT radio interface Problems with DECT and H&W 1. Make sure that the radio interface(s) is (are) correctly connected. 2. Shut down the PC and switch it off. Unplug the plug-in power supply of the PC radio interface from the power outlet for 5 seconds. Switch the milling unit off. Restore all cable connections and test these. Start over again at Preparations, Item 2. 3. Open the "Settings" / "Configuration" / "Devices..." menu. Select the required milling unit in the "Configure Devices" dialog box and click the "Configure" button. Make sure that the correct COM interface and baud rate have been selected. The baud rate must be set to 115200. If an optical impression unit is used, set the COM 1 port. When using a PC set the port to which the radio interface is connected. 4. Should the installation of the software on the milling unit fail again, attempt the installation using the serial cable supplied. 1.5.3 Download via the Höft&Wessel radio interface Preparations Preparations 1. For this installation step, place your PC as close as possible to the milling unit. 2. Switch on the PC. The milling unit must be switched off. Performing a download, Hu.W, cable, new Downloading the milling program Switching the milling unit on Switch the milling unit on (B), while keeping the download key (A) pressed. You can release the Download key on the milling unit after approx. 5 seconds. The green LED on the milling unit is lit and the yellow LED is off. Software note for CEREC 3D Software versions NOTE: For a software update/upgrade from Version 2.8X to Version 3.1X, the milling software is automatically downloaded to the milling unit when the CEREC 3D user software is started. In this case, the steps described are not required after starting the CEREC 3D program. For a software upgrade from Version 2.6X or lower to Version 3.1X, proceed as follows. Configuring the milling unit Configuring the milling unit 1. Start the CEREC 3D program. D 3439.116.10.05.02 02.2008 7
1 Installation Sirona Dental Systems GmbH Installing the software on the milling unit (download) Installation completed The message "Downloading software to COMx" (COM1, COM2,... depending on which interface the milling unit is connected to) appears in the status bar. Wait until the status display goes out. 2. Select the menu item "Settings"/"Configuration"/ "Devices...". 3. Select the milling unit to be configured in the "Configure Devices" dialog box and click the "Configure" button. 4. Enter a name for this milling unit ("Milling unit" is offered as the default name). 5. Corresponding to your unit configuration, place a checkmark in front of "Scanner", in front of "inlab gearhead installed" and, if installed, in front of "Large watertank". 6. Click "OK". 7. After a successful download, a green check mark appears next to the milling unit symbol if the milling unit and scanner were calibrated beforehand. Click the "OK" button to close the "Configure Devices" dialog box. The installation is now completed. Should problems have occurred in one of the above items, please observe the instructions on the next page 8 D 3439.116.10.05.02 02.2008
Sirona Dental Systems GmbH 1 Installation Installing the software on the milling unit (download) 1.5.4 Procedure in case of problems downloading via the Höft&Wessel radio interface Problems with DECT and H&W 1. Make sure that the radio interface(s) is (are) correctly connected. 2. Shut down the PC and switch it off. Unplug the plug-in power supply of the PC radio interface from the power outlet for 5 seconds. Switch the milling unit off. Restore all cable connections and test these. Start over again at Preparations, Item 2. 3. Open the "Settings" / "Configuration" / "Devices..." menu. Select the required milling unit in the "Configure Devices" dialog box and click the "Configure" button. Make sure that the correct COM interface and baud rate have been selected. The baud rate must be set to 115200. If an optical impression unit is used, set the COM 1 port. When using a PC set the port to which the radio interface is connected. 4. Should the installation of the software on the milling unit fail again, attempt the installation using the serial cable supplied. 1.5.5 Download via the Futaba FRH-SD03Tx radio interface Preparations Preparations 1. For this installation step, place your PC as close as possible to the milling unit. 2. Switch on the PC. The milling unit must be switched off. Configuring the Futaba milling unit Configuring the milling unit 1. Start the CEREC 3D program. 2. Select the menu item "Settings"/"Configuration"/ "Devices...". 3. Select the milling unit to be configured in the "Configure Devices" dialog box and click the "Configure" button. 4. Check and, if necessary, change the following: for the COM port to which the radio module is connected, the baud rate must be set to 19200. 5. Confirm these checks/changes with "OK". Leave the "Configure Devices" dialog box open. Performing a download, Hu.W, cable, new Downloading the milling program Switching the milling unit on Switch the milling unit on (B), while keeping the download key (A) pressed. You can release the Download key on the milling unit after approx. 5 seconds. D 3439.116.10.05.02 02.2008 9
1 Installation Sirona Dental Systems GmbH Installing the software on the milling unit (download) The green LED on the milling unit is lit and the yellow LED is off. Registering the milling unit, Futaba Registering the milling unit 1. Click "Refresh status" in the "Configure Devices" dialog box. Installation completed The message "Downloading software to COMx" (COM1, COM2,... depending on which interface the milling unit is connected to) appears in the status bar. Wait until the status display goes out. 2. Enter a name for this milling unit ("Milling unit" is offered as the default name). 3. Corresponding to your unit configuration, place a checkmark in front of "Scanner", in front of "inlab gearhead installed" and, if installed, in front of "Large watertank". 4. Click "OK". 5. After a successful download, a green check mark appears next to the milling unit symbol if the milling unit and scanner were calibrated beforehand. Click the "OK" button to close the "Configure Devices" dialog box. The installation is now completed. Should problems have occurred in one of the above items, please observe the instructions on the next page 10 D 3439.116.10.05.02 02.2008
Sirona Dental Systems GmbH 1 Installation Installing the software on the milling unit (download) 1.5.6 Procedure in case of problems downloading via the Futaba FRH-SD03Tx radio interface Problems with DECT and H&W 1. Make sure that the radio interface(s) is (are) correctly connected. 2. Shut down the PC and switch it off. Switch the milling unit off. Restore all cable connections and test these. Start over again at Preparations, Item 2. 3. Open the "Settings" / "Configuration" / "Devices..." menu. Select the required milling unit in the "Configure Devices" dialog box and click the "Configure" button. Make sure that the correct COM interface and baud rate have been selected. The baud rate must be set to 19200. If an optical impression unit is used, set the COM 1 port. When using a PC set the port to which the radio interface is connected. 4. Should the installation of the software on the milling unit fail again, attempt the installation using the serial cable supplied. 1.5.7 Download using the serial cable supplied Preparations, cable Preparations Switch on the PC. The milling unit must be switched off. Performing a download, Hu.W, cable, new Downloading the milling program Switching the milling unit on Switch the milling unit on (B), while keeping the download key (A) pressed. You can release the Download key on the milling unit after approx. 5 seconds. The green LED on the milling unit is lit and the yellow LED is off. Software note for CEREC 3D Software versions NOTE: For a software update/upgrade from Version 2.8X to Version 3.1X, the milling software is automatically downloaded to the milling unit when the CEREC 3D user software is started. In this case, the steps described are not required after starting the CEREC 3D program. For a software upgrade from Version 2.6X or lower to Version 3.1X, proceed as follows. Configuring the milling unit Configuring the milling unit 1. Start the CEREC 3D program. D 3439.116.10.05.02 02.2008 11
1 Installation Sirona Dental Systems GmbH Installing the software on the milling unit (download) Installation completed The message "Downloading software to COMx" (COM1, COM2,... depending on which interface the milling unit is connected to) appears in the status bar. Wait until the status display goes out. 2. Select the menu item "Settings"/"Configuration"/ "Devices...". 3. Select the milling unit to be configured in the "Configure Devices" dialog box and click the "Configure" button. 4. Enter a name for this milling unit ("Milling unit" is offered as the default name). 5. Corresponding to your unit configuration, place a checkmark in front of "Scanner", in front of "inlab gearhead installed" and, if installed, in front of "Large watertank". 6. Click "OK". 7. After a successful download, a green check mark appears next to the milling unit symbol if the milling unit and scanner were calibrated beforehand. Click the "OK" button to close the "Configure Devices" dialog box. The installation is now completed. Should problems have occurred in one of the above items, please observe the instructions on the next page 12 D 3439.116.10.05.02 02.2008
Sirona Dental Systems GmbH 1 Installation Installing the software on the milling unit (download) 1.5.8 Procedure in case of problems downloading with the supplied serial cable Problems with the cable 1. Shut down the PC and switch it off. Switch the milling unit off. Restore all cable connections and test these. Make sure that you have used the 2 meter long serial interface cable supplied. Start over again at Preparations. 2. Open the "Settings" / "Configuration" / "Devices..." menu. Select the required milling unit in the "Configure Devices" dialog box and click the "Configure" button. Make sure that the correct COM interface and baud rate have been selected. The baud rate must be set to 115200. When using an acquisition unit with external interface extension set the COM 2 port. When using an acquisition unit without external interface extension, you must proceed as for a PC and select the port to which the serial cable is connected. D 3439.116.10.05.02 02.2008 13
2 Software Update, Version 3.1X Sirona Dental Systems GmbH General information 2 Software Update, Version 3.1X 2.1 General information Note on CEREC 3D NOTE: This software does not allow the loading, importing and editing of bridge frameworks and implants. Continuous further product development Continuous further product development In the course of continuous further product development, this software has been developed further regarding the points listed below: List for CEREC 3D Failure to detect the new baud rate [ 14] Wrong blocks in the block selection dialog [ 14] MC XL [ 14] Displacement of the proximal contact line during inlay correlation [ 15] Prepositioning tool for crown dental database (in the CEREC 3D mode [ 15]) Simultaneous display of occlusal and proximal contact points [ 15] Loading of restorations in CEREC 3D Mode and Master Mode [ 16] VITABLOCS TriLuxe forte [ 16] New milling instruments [ 16] New materials from 3M ESPE [ 16] Windows Vista compatible [ 17] 2.2 Failure to detect the new baud rate When the radio interface was changed (e.g. from Futaba to H&W), the software retained the previously set baud rate during the download for the CEREC 3 milling unit. For this reason, the acquisition unit did not communicate with the milling unit. This problem occurred only with CEREC 3 milling units in cases where the new radio interface operated at a different baud rate than the old one had used 2.3 Wrong blocks in the block selection dialog If possible, the software will automatically rotate the ceramic block 90 so that a restoration can be milled with the smallest block (e.g. I12/90). In rare cases, the software suggested a block size which was too small, and therefore not suitable for the restoration (e.g. I12 and I14 were displayed, however, only I14 was large enough). 2.4 MC XL The following change was implemented in the block database: Effective immediately, fast grinding is no longer available for e.max CAD. 14 D 3439.116.10.05.02 02.2008
Sirona Dental Systems GmbH 2 Software Update, Version 3.1X Displacement of the proximal contact line during inlay correlation The filter change prompt was introduced. The user is prompted to change the filter at the same time in the water change dialog. This message must be confirmed; otherwise it will display repeatedly. The automatic reset of the warning after one minute has been removed. 2.5 Displacement of the proximal contact line during inlay correlation Until now, it was not possible to move the attachment points of the proximal contact line in a large area. This is now possible. 2.6 Prepositioning tool for crown dental database (in 3D mode) With this software version it is possible to exit from the Restoration step to the prepositioning tool in the 3D mode with the crown dental database using the "Undo" command. There, it is possible to move or rotate the crown using the position and rotation tools. Settling and cusp settling are automatically performed following prepositioning. 2.7 Simultaneous display of occlusal and proximal contact points With this software version the occlusal and proximal contact points can be displayed without distortion (see figure right). The left figure shows a crown restoration suggestion with an older software version. Here, you see problems with the visualization in regions in which the occlusal and proximal planes overlap. The right image shows a crown restoration suggestion using the software Version 3.1X with the correct display in the overlapping regions. D 3439.116.10.05.02 02.2008 15
2 Software Update, Version 3.1X Sirona Dental Systems GmbH Loading of restorations in CEREC 3D Mode and Master Mode 2.8 Loading of restorations in CEREC 3D Mode and Master Mode All stored restorations can now be shown in the selection dialog both in CEREC 3D Mode and in Master Mode in the preview, and they can be loaded in Master Mode. Images produced in Master Mode can still not be loaded in CEREC 3D Mode. 2.9 VITABLOCS TriLuxe forte In the milling preview, the VITABLOCS TriLuxe forte blocks are displayed with four layers instead of three layers, as previously. The selection of the VITABLOCS TriLuxe forte blocks in the milling preview dialog is now also separate from the normal VITABLOCS TriLuxe blocks. 2.10 New milling instruments There are two new milling instruments for Product MC XL: Step Bur 12 S Cylinder Pointed Bur 12 S They are suitable for milling the following materials: Sirona CEREC Blocs Sirona CEREC Blocs PC VITA Mark 2 VITA TriLuxe VITA TriLuxe Forte VITA Esthetic Line Ivoclar Vivadent IPS Empress CAD Ivoclar Vivadent IPS Empress CAD Multi Ivoclar Vivadent IPS e.max CAD Merz artegral imcrown 3M ESPE Paradigm MZ 100 3M ESPE Paradigm C 2.11 New materials from 3M ESPE In the block selection two additional materials can be selected from 3M ESPE: the composite material Paradigm MZ 100 the glass ceramic Paradigm C 3M ESPE Paradigm MZ 100 blocks 3M ESPE Paradigm MZ 100 blocks are produced from the restoration material Z100, a universal composite. They are available in 2 sizes (10 and 14) as well as in six colors (A1, A2, A3, A3.5, B3, dental enamel). The Paradigm MZ100 blocks are suitable for milling the following restorations: inlays, onlays, crowns and veneers. 16 D 3439.116.10.05.02 02.2008
Sirona Dental Systems GmbH 2 Software Update, Version 3.1X Windows Vista compatible 3M ESPE Paradigm C blocks 3M ESPE Paradigm C blocks are made from a leucite-reinforced, glass ceramic material. They are available in five sizes (V-5-12, 8, 10, 12 and 14) as well as in six balanced colors (bleached, A1, A2, A3, A3.5 and B3). The Paradigm C blocks are suitable for milling the following restorations: inlays, onlays, crowns and veneers. 2.12 Windows Vista compatible The CEREC 3D software update, Version 3.10 is Windows Vista compatible. D 3439.116.10.05.02 02.2008 17
té=êéëéêîé=íüé=êáöüí=íç=ã~âé=~åó=~äíéê~íáçåë=ïüáåü=ã~ó=äé=êéèìáêéç=çìé=íç=íéåüåáå~ä=áãéêçîéãéåíëk «=páêçå~=aéåí~ä=póëíéãë=dãäe=ommu péê~åüéw==éåöäáëåü= mêáåíéç=áå=déêã~åó a=pp44.nnsknmkmrkmo MOKOMMU ûkjkêkw= NMV=TNQ páêçå~=aéåí~ä=póëíéãë=dãäe áå=íüé=rp^w c~äêáâëíê~ É=PN páêçå~=aéåí~ä=póëíéãë=ii` SQSOR=_ÉåëÜÉáã QUPR=páêçå~=aêáîÉI=pìáíÉ=NMM déêã~åó `Ü~êäçííÉI=k`=OUOTP ïïïkëáêçå~kåçã rp^ lêçéê=kç RV=UQ=NSN=a=PP44