Draft Version Setup Reference guide for KX-HTS Series (Tested with HTS824 Version 1.5) Netia SIP Trunk service with External Router Version 0.1(PSN) 22th.June, 2017
SUMMARY This document is a reference for configuring Netia SIP trunks onto Panasonic HTS and includes the settings required for Incoming Call DDI routing and Outgoing Call CLI presentation. SIP trunk specific account details are provided to you by Netia. Attention: This document was created based on the results of test environment accounts. Panasonic cannot guarantee SIP Trunk operation in all environments, however as a result of completing this Inter-Operability Test Panasonic will provide technical support for any issues experienced an assist as far as possible in providing a resolution. Please obtain relevant information from Service provider before configuration of SIP trunks. Panasonic will not be held liable for any information provided in this guidance document. Information used in this document is for interoperability testing. Information and Specifications in this document are subject to change without notice. Note [FAX] Unable to use FAX to PSTN when FAX CNG is detected on Netia with short protocol of FAX. Configure it to disable on the FAX. [Transfer/Forward function] Configure PBXs CLIP on HTS when operate Transfer/Forwarded. [Hold, REFER, Conference by other Party] Hold Method is supported by V1.7 Beta confirmed. Upload the firmware to Ver1.7 or later. Table of Contents (1) SIP Trunk, Extension Port Number and NAT Configuration: Page 4 (2) Network Settings: Page 5 (3) Trunk Port Attribution: Page 7 (4) Provisioning a SIP trunk: Page 8 (5) Incoming Call Routing: Page 12 (6) Outgoing Call CLI: Page 13 (7) CLIR Outgoing Call (Anonymous calls): HTS Not supported Page 14 (8) Router/Firewall Port Forwarding: Page 15 2
With External Router Example Existing User Network: 192.168.22.0 / Subnet Mask: 255.255.255.0 (/24) Existing Router IP Address: 192.168.22.1, Static DNS: Primary DNS Server 192.168.22.1 / Secondary DNS Server: 8.8.8.8 Internet Existing Router (192.168.22.1/24) Existing User Network (192.168.22.0 /24) KX-HDV series (e.g., KX-HDV230) HUB PC (Enable DHCP) To Existing Router To PC/HUB LAN1: 192.168.0.101/24 WAN1: 192.168.22.99/24 Note Configure the settings according to the IP address system of the existing user network. Also, set the IP address which does not duplicate other IP devices. 3
(1) SIP Trunk, Extension Port Number and NAT Configuration SIP Extension & SIP Trunk Common Select [PBX Configuration] - [2. Extension] - [7.SIP Extension Property] [SIP Extension & SIP Trunk Common] 1. Voice (RTP) UDP port No.(Server): Leave at 12000-2. SIP Port Number: Leave at 5060 3. NAT Traversal: Leave Off 4. NAT Fixed Global IP Address: Leave at 0.0.0.0 All other settings can be left at default. Click [Apply] Click [Apply Now] 4
(2) Network Settings Network Configuration WAN Setting Select [Network Configuration] - [3.WAN] [1.WAN Setting] and Select [WAN 1 Channel] Click [Modify] HTS WAN-1 IP: 192.168.22.99 (Example) Assigned HTS WAN IP address by user network administrator 1. WAN Type: Fix IP 2. WAN Connection Name: Leave WAN1_Fix_IP - Reference only- 3. IP address, by your ISP: 192.168.22.99 (Enter your actual IP address) 4. Subnet Mask: 255.255.255.0 5. ISP Gateway Address: 192.168.22.1 6. Static DNS Change to Enable 7. Primary DNS Server: 192.168.22.1 8. Secondary DNS Server: 8.8.8.8 Click [Apply] 5
LAN Settings Go to [Network Configuration] - [4.LAN] - [2.LAN Settings] 1. IP Address: 192.168.0.101 2. Subnet Mask: 255.255.255.0 3. DHCP Mode: Server [DHCP server] 4. IP Pool Staring Address: Leave 192.168.0.102 5. IP Pool Ending Address: Leave 192.168.0.254 6. Lease Time: Leave One day 6
(3) Trunk Port Attribution Select [PBX Configuration] - [3.Trunk] - [1.Port] and click [Edit / CO Line Number 1 to 8] [CO Line Number 1] 1. Attribution: SIP Carrier - 1 2. Trunk Group: Leave at 1 Click [Apply] Click [Apply Now] Example, Configure CO-Line 1-2: SIP Carrier-1, Other CO-Line: No Connect SIP Trunk 2 Channels Others 6 CO Line are not used, Configure to No Connect from Analog Line. 7
(4) Provisioning the SIP Trunk SIP Trunk Property - Common Select [PBX Configuration] - [3.Trunk] - [7. SIP Trunk Property] - [Common] 1. DNS SRV Record Resolve Ability: Leave Disable [Register] 2. Register Sending Interval (s): Leave at 3600 3. Register Resending Interval (s): Leave at 300 4. RTCP Sending Interval (s): Leave at 5 8
SIP Trunk Property continued SIP Carrier-1 [SIP Carrier-1] 1. Provider Name: Enter a name reference only 2. SIP Server Name: netiasa.integralnet.pl 3. SIP Server IP Address: Leave at 0.0.0.0 4. SIP Server port Number: Leave at 5060 5. SIP Server Domain: Not required 6. Subscriber Number: Not required [Account] 7. User name: Enter the SIP Account (User name) as supplied by Netia. (Note this is user name without @netiasa.integralnet.pl) For example: SIP Account (User name) = 221234560 Enter: 221234560 8. Authentication ID: Enter the Authentication ID as supplied by Netia. (Note this is user name without @ netiasa.integralnet.pl) For example: Authentication ID = 221234560 Enter: 221234560 9. Authentication Password: Enter the Authentication Password as supplied by Netia For example: Authentication Password = password Enter: password [Register] 10. Register Ability: Enable 9
SIP Trunk Property continued SIP Carrier-1 [Calling Party] 1. Header Type: P-Preferred-Identity Header 2. Host Name: netiasa.integralnet.pl 3. Format: Leave Without + 4. Send CLIP of caller when call from SIP Carrier is forwarded to same SIP carrier: Change to Disable [Called Party] 5. Format: Leave Without + 10
SIP Trunk Property continued SIP Carrier-1 [Voice] 1. IP Codec Priority 1st: G.711A 2. IP Codec Priority 2nd: G.711Mu 3. IP Codec Priority 3rd: Leave None 4. Packet Sampling Time: Leave at 20 (ms) 5. DTMF: Leave Outband (RFC2833) 6. Payload Type (DTMF): Leave at 101 [Session] 9. Session Timer Ability: Leave Enabled (Passive) 10. Session Expire Timer: Leave at 180 11. Session Incoming Refresher Request: Leave UAC Click [Apply] Click [Apply Now] Save the System data Click [Save & Logout] 11
(5) Incoming Call Routing DDI Table [PBX Configuration] - [3.Trunk] - [3.DDI] 1. DDI Number: Enter the DDI number in the format (as below) Example Landline Number: 22 123 4561 Enter: 221234561 2. Name: Determined by the installer (optional setting) 3. Destinations: Determined by the installer (extension number, group etc) Click [Apply] 12
(6) Outgoing Call CLI CLIP [PBX Configuration] - [Target Extension] Click (Example: Extension 101) [Port - Extension 101 / CLIP] 1. Extension Name: HTS Ext Name101 (Example) 2. SIP Carrier -1: 221234561 (Example) Click [Apply] Click [Apply Now] Click [Save & Logout] 13
(7) CLIR Outgoing Call (Anonymous calls) *Note: HTS does not support CLIR as function. 14
(8) Router/Firewall Port Forwarding For External router setup, configure Port Forwarding on the router as follows: udp port 5060 to HTS WAN1 IP address (e.g. 192.168.22.101) udp port range 12000-20000 (RTP) to WAN1 IP address (e.g. 192.168.22.101) IMPORTANT! To secure the PBX from illegal attacks, please restrict the above port forwarding ports to only be accessible from the Netia source IP addresses. END OF DOCUMENT 15