Important notice Dear Customer, On 7 February 07 the former NXP Standard Product business became a new company with the tradename Nexperia. Nexperia is an industry leading supplier of Discrete, Logic and PowerMOS semiconductors with its focus on the automotive, industrial, computing, consumer and wearable application markets In data sheets and application notes which still contain NXP or Philips Semiconductors references, use the references to Nexperia, as shown below. Instead of http://www.nxp.com, http://www.philips.com/ or http://www.semiconductors.philips.com/, use http://www.nexperia.com Instead of sales.addresses@www.nxp.com or sales.addresses@www.semiconductors.philips.com, use salesaddresses@nexperia.com (email) Replace the copyright notice at the bottom of each page or elsewhere in the document, depending on the version, as shown below: - NXP N.V. (year). All rights reserved or Koninklijke Philips Electronics N.V. (year). All rights reserved Should be replaced with: - Nexperia B.V. (year). All rights reserved. If you have any questions related to the data sheet, please contact our nearest sales office via e-mail or telephone (details via salesaddresses@nexperia.com). Thank you for your cooperation and understanding, Kind regards, Team Nexperia
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open Rev. 07 0 April 007 Product data sheet. Product profile. General description PNP Resistor-Equipped Transistors (RET) family in small plastic packages. Table. Product overview Type number Package NPN complement NXP JEITA JEDEC PDTA4TE SOT46 SC-75 - PDTC4TE PDTA4TK SOT46 SC-59A TO-6 PDTC4TK PDTA4TM SOT88 SC-0 - PDTC4TM PDTA4TS [] SOT54 SC-4A TO-9 PDTC4TS PDTA4TT SOT - TO-6AB PDTC4TT PDTA4TU SOT SC-70 - PDTC4TU [] Also available in SOT54A and SOT54 variant packages (see Section ).. Features 00 ma output current capability Built-in bias resistors Simplifies circuit design Reduces component count Reduces pick and place costs. Applications Digital applications Control of IC inputs Cost-saving alternative to BC857 series in digital applications Low current peripheral driver.4 Quick reference data Table. Quick reference data Symbol Parameter Conditions Min Typ Max Unit V CEO collector-emitter voltage open base - - 50 V I O output current - - 00 ma R bias resistor (input) 7 0 kω
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open. Pinning information Table. Pinning Pin Description Simplified outline Symbol SOT54 input (base) output (collector) GND (emitter) 00aab47 R 006aaa7 SOT54A input (base) output (collector) GND (emitter) 00aab48 R 006aaa7 SOT54 variant input (base) output (collector) GND (emitter) 00aab447 R 006aaa7 SOT; SOT; SOT46; SOT46 input (base) GND (emitter) output (collector) R 006aaa44 sym009 SOT88 input (base) GND (emitter) output (collector) Transparent top view R sym009 PDTA4T_SER_7 NXP B.V. 007. All rights reserved. Product data sheet Rev. 07 0 April 007 of
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open. Ordering information Table 4. Ordering information Type number Package Name Description Version PDTA4TE SC-75 plastic surface-mounted package; leads SOT46 PDTA4TK SC-59A plastic surface-mounted package; leads SOT46 PDTA4TM SC-0 leadless ultra small plastic package; solder lands; SOT88 body.0 0.6 0.5 mm PDTA4TS [] SC-4A plastic single-ended leaded (through hole) package; SOT54 leads PDTA4TT - plastic surface-mounted package; leads SOT PDTA4TU SC-70 plastic surface-mounted package; leads SOT [] Also available in SOT54A and SOT54 variant packages (see Section and Section 9). 4. Marking Table 5. Marking codes Type number Marking code [] PDTA4TE PDTA4TK PDTA4TM DE PDTA4TS TA4T PDTA4TT * PDTA4TU * [] * = -: made in Hong Kong * = p: made in Hong Kong * = t: made in Malaysia * = W: made in China PDTA4T_SER_7 NXP B.V. 007. All rights reserved. Product data sheet Rev. 07 0 April 007 of
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open 5. Limiting values 6. Thermal characteristics Table 6. Limiting values In accordance with the Absolute Maximum Rating System (IEC 604). Symbol Parameter Conditions Min Max Unit V CBO collector-base voltage open emitter - 50 V V CEO collector-emitter voltage open base - 50 V V EBO emitter-base voltage open collector - 5 V I O output current - 00 ma I CM peak collector current single pulse; - 00 ma t p ms P tot total power dissipation T amb 5 C PDTA4TE [] - 50 mw PDTA4TK [] - 50 mw PDTA4TM [][] - 50 mw PDTA4TS [] - 500 mw PDTA4TT [] - 50 mw PDTA4TU [] - 00 mw T j junction temperature - 50 C T amb ambient temperature 65 +50 C T stg storage temperature 65 +50 C [] Device mounted on an FR4 Printed-Circuit Board (PCB), single-sided copper, tin-plated and standard footprint. [] Reflow soldering is the only recommended soldering method. [] Device mounted on an FR4 PCB with 60 µm copper strip line, standard footprint. Table 7. Thermal characteristics Symbol Parameter Conditions Min Typ Max Unit R th(j-a) thermal resistance from junction to ambient in free air PDTA4TE [] - - 8 K/W PDTA4TK [] - - 500 K/W PDTA4TM [][] - - 500 K/W PDTA4TS [] - - 50 K/W PDTA4TT [] - - 500 K/W PDTA4TU [] - - 65 K/W [] Device mounted on an FR4 PCB, single-sided copper, tin-plated and standard footprint. [] Reflow soldering is the only recommended soldering method. [] Device mounted on an FR4 PCB with 60 µm copper strip line, standard footprint. PDTA4T_SER_7 NXP B.V. 007. All rights reserved. Product data sheet Rev. 07 0 April 007 4 of
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open 7. Characteristics Table 8. Characteristics T amb =5 C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit I CBO collector-base cut-off V CB = 50 V; I E =0A - - 00 na current I CEO collector-emitter cut-off current V CE = 0 V; I B =0A - - µa V CE = 0 V; I B =0A; - - 50 µa T j = 50 C I EBO emitter-base cut-off V EB = 5 V; I C =0A - - 00 na current h FE DC current gain V CE = 5 V; I C = ma 00 - - V CEsat collector-emitter saturation voltage I C = 0 ma; I B = 0.5 ma - - 50 mv R bias resistor (input) 7 0 kω C c collector capacitance V CB = 0 V; I E =i e =0A; - - pf f = MHz 600 006aaa554 006aaa555 h FE 400 () V CEsat (V) 00 () () 0 () () () Fig. 0 0 0 0 I C (ma) V CE = 5 V () T amb = 50 C () T amb =5 C () T amb = 40 C DC current gain as a function of collector current; typical values Fig. 0 0 0 0 I C (ma) I C /I B =0 () T amb = 00 C () T amb =5 C () T amb = 40 C Collector-emitter saturation voltage as a function of collector current; typical values PDTA4T_SER_7 NXP B.V. 007. All rights reserved. Product data sheet Rev. 07 0 April 007 5 of
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open 8. Package outline.8.4 0.95 0.60..7..0 0.45 0.5 0.6 0..75.45 0.9 0.7.0.5.7. 0.0 0.5 0.5 0.0.9 0.50 0.5 0.6 0.0 04--04 04-- Fig. Package outline SOT46 (SC-75) Fig 4. Package outline SOT46 (SC-59A/TO-6) 0.6 0.55 0.55 0.47 0.50 0.46 4..6 0.45 0.8 0.0 0. 0.0 0. 0.65.0 0.95 4.8 4.4 0.48 0.40.7.54 0.0 0. 0.5 0-04-0 5. 5.0 4.5.7 04--6 Fig 5. Package outline SOT88 (SC-0) Fig 6. Package outline SOT54 (SC-4A/TO-9) 4..6 4.8 4.4 max 0.48 0.40 0.45 0.8.54 5.08 4..6 4.8 4.4.5 max 0.45 0.8 0.48 0.40.7.54.7 5. 5.0 4.5.7 5. 5.0 4.5.7 04-06-8 05-0-0 Fig 7. Package outline SOT54A Fig 8. Package outline SOT54 variant PDTA4T_SER_7 NXP B.V. 007. All rights reserved. Product data sheet Rev. 07 0 April 007 6 of
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open.0.8. 0.9..8. 0.8 0.45 0.5.5..4. 0.45 0.5..0.5.5.9 0.48 0.8 0.5 0.09. 0.4 0. 0.5 0.0 04--04 04--04 Fig 9. Package outline SOT (TO-6AB) Fig 0. Package outline SOT (SC-70) PDTA4T_SER_7 NXP B.V. 007. All rights reserved. Product data sheet Rev. 07 0 April 007 7 of
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open 9. Packing information Table 9. Packing methods The indicated -xxx are the last three digits of the NC ordering code. [] Type number Package Description Packing quantity 000 5000 0000 PDTA4TE SOT46 4 mm pitch, 8 mm tape and reel -5 - -5 PDTA4TK SOT46 4 mm pitch, 8 mm tape and reel -5 - -5 PDTA4TM SOT88 mm pitch, 8 mm tape and reel - - -5 PDTA4TS SOT54 bulk, straight leads - -4 - SOT54A tape and reel, wide pitch - - -6 tape ammopack, wide pitch - - -6 SOT54 variant bulk, delta pinning - - - PDTA4TT SOT 4 mm pitch, 8 mm tape and reel -5 - -5 PDTA4TU SOT 4 mm pitch, 8 mm tape and reel -5 - -5 [] For further information and the availability of packing methods, see Section. PDTA4T_SER_7 NXP B.V. 007. All rights reserved. Product data sheet Rev. 07 0 April 007 8 of
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open 0. Revision history Table 0. Revision history Document ID Release date Data sheet status Change notice Supersedes PDTA4T_SER_7 007040 Product data sheet - PDTA4T_SERIES_6 Modifications: The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. Legal texts have been adapted to the new company name where appropriate. Type number PDTA4TEF removed Section. Features : amended Section. Applications : amended Table 4 Ordering information : added Table 5 Marking codes : enhanced table note section Table 6 Limiting values : I CM peak collector current conditions added Figure,, 7 and 8: added Figure, 4, 5, 6, 9 and 0: superseded by minimized package outline drawings Section 9 Packing information : added Section Legal information : updated PDTA4T_SERIES_6 004080 Product specification - PDTA4T_SERIES_5 PDTA4T_SERIES_5 000909 Product specification - PDTA4T_SERIES_4 PDTA4T_SERIES_4 00040 Product specification - PDTA4TE_ PDTA4TK_ PDTA4TS_ PDTA4TT_ PDTA4TU_ PDTA4TE_ 99807 Preliminary specification - PDTA4TE_ PDTA4TK_ 998055 Product specification - PDTA4TK_ PDTA4TS_ 998055 Product specification - PDTA4TS_ PDTA4TT_ 99904 Objective specification - PDTA4TT_ PDTA4TU_ 99904 Product specification - PDTA4TU_ PDTA4T_SER_7 NXP B.V. 007. All rights reserved. Product data sheet Rev. 07 0 April 007 9 of
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open. Legal information. Data sheet status Document status [][] Product status [] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [] Please consult the most recently issued document before initiating or completing a design. [] The term short data sheet is explained in section Definitions. [] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.. Definitions Draft The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.. Disclaimers General Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer s own risk. Applications Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 604) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights..4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.. Contact information For additional information, please visit: http://www.nxp.com For sales office addresses, send an email to: salesaddresses@nxp.com PDTA4T_SER_7 NXP B.V. 007. All rights reserved. Product data sheet Rev. 07 0 April 007 0 of
PDTA4T series PNP resistor-equipped transistors; R = 0 kω, R = open. Contents Product profile........................... General description....................... Features............................... Applications............................4 Quick reference data..................... Pinning information...................... Ordering information..................... 4 Marking................................ 5 Limiting values.......................... 4 6 Thermal characteristics................... 4 7 Characteristics.......................... 5 8 Package outline......................... 6 9 Packing information...................... 8 0 Revision history......................... 9 Legal information....................... 0. Data sheet status...................... 0. Definitions............................ 0. Disclaimers........................... 0.4 Trademarks........................... 0 Contact information..................... 0 Contents.............................. Please be aware that important notices concerning this document and the product(s) described herein, have been included in section Legal information. NXP B.V. 007. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 0 April 007 Document identifier: PDTA4T_SER_7