The ACPGM-80V has a built in Dual-Link module that allows connection of Android and other devices with two-way mirroring control. Adds a reverse camera input with active parking guidelines. Adds 2 Audio/Video inputs. Compatible with Cadillac CUE, GM MyLink (io3, io5 & io6) Infotainment Systems with 4.3 and 8 screens. ACPGM-80V MODULE CAN BOX CUE Harness MyLink Harness MICROPHONE VIDEO CABLE PUSH BUTTON SWITCH USB CABLE 3.5 AUX CABLE Audio Cable 1 / 8
2 / 8
Below is an example of how to remove the radio of a Cadillac for reference. Other models may have a different way of removing the radio. 1. Remove radio to gain access to the rear connectors. Be careful not to break the mounting clips on the radio trim bezel. Please see pictures above for reference. 2. Unplug the radio connector, USB and mini USB from radio. 3. Plug the male power connector to the harness provided in this kit. Please note that the CUE system will have a 16-pin connector and the MyLink System will have a 10-pin connector. A harness for each system is included in the ACPGM-80V kit. 4. Plug the 6-pin Molex connector of the harness being used to the CAN box included in the kit. 5. Plug male mini USB connector from the vehicle into the female mini USB port of the LVDS cable provided. 6. Plug the male mini USB of the LVDS cable to the radio. 7. Reconnect the USB and any other connector that was unplugged during removal of the radio. 8. Plug the audio 3.5mm Aux Cable into the interface and route to the vehicle s OE Aux input jack. 9. Install the camera (not included) to the rear of the vehicle and run the cable towards the interface location. 10. Plug the camera RCA connector to the red RCA of the video harness. 11. Use the green wire from the CAN Box power harness to power the camera. 12. Use the two extra video inputs and audio cable to connect other AV sources. 13. Test the system for functionality before reinstalling the radio. Put the vehicle in reverse and verify that the camera image is seen on the screen. For touch screen radios, press and hold anywhere on the screen for 3 seconds to toggle between the AV inputs. For non-touch screen radios, press the MENU button to toggle between AV inputs. 14. Reverse the order of installation to put back the radio and all the trim. 3 / 8
DIP DOWN (ON) UP (OFF) 1 RGBS INPUT ENABLED RGBS INPUT DISABLED 2 AV1 ON AV1 OFF 3 AV2 ON AV2 OFF 4 When using the RGB port and need a high definition input. When using CVBS (RCA) camera video input. 5 When using an aftermarket camera. When using the OEM camera. 6 Set to OFF 7, 8 Both DOWN = 4.3 screen Both UP = 8 Screen To toggle to Smartphone Connectivity mode (i.e. Android Auto), press the MENU button on the radio. 1. SCREEN CALIBRATION The screen needs to be calibrated to the ACPGM-80V after it is installed for the first time. Please see calibration steps below: 1. Click 5 times on the screen to activate screen adjustment. 2. Adjust the screen position using the arrows until the green edges can be seen on all sided. Click OK when finished. 3. Click on the cross that will show up around the screen to complete the touch calibration. 4 / 8
2. ANDROID SMARTPHONE CONNECTION To use Android Auto and dual controlled Android Mirroring, please follow the steps below: 1. Go to Settings and then go to About device. 2. Go to Software info and click Build Number 5 times to activate Developer Mode. 3. Go to Developer options and then enable USB debugging. 4. You will need to install two apps: Android Auto and DualLinkUnlocked. 5. Scan QR code to download DualLinkUnlocked App: 6. Go to the Playstore to download the Android Auto app. 1. Connect the original USB cable to the interface s USB extension cable and to the phone. Android Auto will automatically be launched. User may use the OE touch screen to control all the functions. If connection failed or lost message appears on the screen, check USB connection and try again. 2. Once Android Auto is launched, users may use the original features of Android Auto such as Google Maps, Music, Radio, Call, etc. In case the phone has no onscreen HOME or BACK button, user can download onscreen navigation buttons from Playstore. 5 / 8 3. Press the HOME key or BACK button to exit Android Auto. Once the phone exits the app, full phone screen mirroring will be shown. User can then use the apps of the phone such as Waze and Videos. OE touch screen will be used to control the apps. The Screen orientation will depend if the app supports it.
AUDIO: To get the audio from the Android device, pair the phone to the vehicle s Bluetooth or connect the phone s AUX output to the vehicle s AUX input for sound to come from the OE speakers. NOTE: When using full phone mirroring two-way control feature, make sure to enable Onscreen Navigation (HOME and BACK) keys in case they are not active. 3. SIDE BUTTONS ON THE MODULE The 3 buttons on the side of the interface is used to fine tune the picture display (MENU, +, -). When the MENU button is pressed, the OSD strings will pop up on the screen. Pressing the +/- will change the settings. CONTRAST Adjust contrast of Navigation screen BRIGHTNESS Adjust brightness of Navigation screen SATURATION Adjust color saturation POSITION H Adjust horizontal position POSITION V Adjust vertical position IR. AV1 Set IR code for AV1 (if applicable) IR. AV2 Set IR code for AV2 (if applicable) Guide-L No Function Guide-R No Function Guide-Control Set to OFF H-Size Adjust screen horizontal size V-Size Adjust screen vertical size To toggle the Smartphone Connectivity function, press the MENU button on the radio or use the supplied Remote Pushbutton Switch. The ACPGM-80V works on the 8 CUE and on the 8 and 4.3 (RPO io3, io5 & io6) MyLink systems. To find the RPO Codes, please check the label in the glove box or under the spare tire location. The label would look like this: 6 / 8
CADILLAC 2016 2017 ATS CTS XTS Escalade SYSTEM / SCREEN SIZE CUE io5/io6 with 8 Screen 2016 2017 XT5 CUE with 8 Screen CHEVROLET 2014 2015 2014 2015 2015 2015 2015 2015 Impala Silverado Suburban Tahoe io3 4" Screen 2016 2017 Cruze MyLink io5/io6 with 8 Screen 2016 2017 2016 2017 Volt (high end) Equinox 6 / 8
Impala MyLink io5/io6 with 8 Screen Silverado Suburban Tahoe MyLink io5/io6 with 8 Screen GMC 2014 2015 2014-2015 Sierra Yukon io3 4 Screen 2016 2017 2015 Acadia Canyon Sierra Yukon IntelliLink io5/io6 with 8 Screen 8 / 8